Spectra APR3-ADM2 : User Guide
Contents
1. SPECTRA Voice Assisted Arm Disarm Module User Manual A RA X SECURITY SYSTEMS Printed in Canada 06 2007 paradox com APR3ADM2 EU02 TABLE OF CONTENTS INTRODUCTION LA na ieee stiles 4 ACCESS CODES da nan kik Stand alone Code default 123456 User Access Codes HOW DO l USE 5 THINGS YOU SHOULD KNOW When Accessing your APR3 ADM2 When Arming or Disarming When Activating or Deactivating an Output When Entering Your Stand alone Code When Using your APRS3 ADM2 TELEPHONE PUSH BUTTON FEATURES 8 Clear 8 Change Stand alone Code 8 9 Activate Deactivate APR3 ADM2 Output 0 9 Hang Up 9 haa k i eie 9 SYSTEM CHECKLIST a 9 APR3 ADM2 EXAMPLE 10 COMPATIBILITY e Spectra 1728 1738 1759MG INTRODUCTION Congratulations for choosing the Paradox Voice Assisted Arm Disarm Module The APR3 ADM turns any touch tone telephone into a keypad With the APR3 ADM2 you can now arm or disarm your Spectra security system as well as activate or deactivate your APR3 ADM2 s programmable outputs PGMs all from your telephone Using detailed voice prompts to guide your way the APR3 ADM2 is as simple as picking up your telephone ACCESS CODES The APR3 ADM2 uses two types2. deactivate the APR3 ADM2 s output press the key and then the 0 key Refer to Example 1 on page 10 STEP 6 To change your stand alone code press the key and then the 8 key After the voice prompt enter your new stand alone code Then enter the same code again so that the APR3 ADM can verify your new code The APR3 ADM2 will confirm the new stand alone code with a Code changed prompt THINGS YOU SHOULD KNOW When Accessing your APR3 ADM2 e To access a system that is connected to an answering machine or service call the APR3 ADM2 hang up wait 10 seconds and then call the APR3 ADM again When Arming or Disarming You will only be able to arm or disarm areas that your User code has access to 6 Spectra User Manual If your security system is partitioned once you have performed an action to a partition you will not be able to perform another action to the same partition until you exit and re enter your user access code If your security system has not been partitioned once you enter your user access code the arming state of the system will automatically be changed and no partition options will be prompted If your security system has been partitioned but your user access code only has access to one partition when you enter your user access code the APR3 ADM will automatically change the arming state of the partition you have access to When Activating or Deactivating an Output Y
3. stand alone code Then enter the same code again so that the InTouch can verify your new code Activate Deactivate APR3 ADM2 Output 0 To activate or deactivate the APR3 ADM2 s output press the key and then the 0 key from your telephone Hang Up 9 When you wish to hang up press the key and then the 9 key to immediately hang up The APR3 ADM2 will confirm the hang up with Good bye If the Hang Up feature is not used A and if no action is performed after 2 minutes the APR3 ADM2 will hang up automatically SYSTEM CHECKLIST Telephone Number Stand alone Code J 6 digits J 4 digits InTouch 9 Output Activates Output follows J Output Timer Manual Deactivation Output Timer Length sec or O min Call hang up and then call back within __ secs of rings before the APR3 ADM2 answers An area and a partition are two words to describe the same thing Your Spectra s partitions are called areas by the APR3 ADM2 APR3 ADM2 EXAMPLE Example 1 Using the APR3 ADM2 Nelson has a Spectra security system and an APR3 ADM2 hooked up at home His security system has two partitions Both partitions are presently armed and the APR3 ADM2 s output which is hooked up to his garage door opener is deactivated Nelson is on his way home and wishes to disarm both partitions and open his garage door Nelson performs the following action 10 Spectra User Manual N
4. elson first dials the telephone number of the line to which the APR3 ADM2 is connected When the APR3 ADM2 picks up it will prompt Nelson with the following Enter your stand alone code Nelson enters his stand alone code The APR3 ADM2 then prompts Nelson with the following Area 1 armed Area 2 armed Output is deactivated Please enter your code Nelson enters his user access code The APR3 ADM2 then prompts Nelson with the following Area 1 armed Area 2 armed Output is deactivated To change enter area number 1 Area number 2 InTouch 11 12 Spectra User Manual Nelson presses the 1 key on his telephone to disarm partition 1 The APR3 ADM2 then prompts Nelson with the following Area 1 disarmed Area 2 armed Output is deactivated To change enter area number 2 Nelson presses the 2 key on his telephone to disarm partition 2 The APR3 ADM2 then prompts Nelson with the following Area 1 disarmed Area 2 disarmed Output is deactivated Please enter your code Nelson then presses the 4 key and then the 0 key on his telephone to activate the output connected to the garage door The APR3 ADM2 then prompts Nelson with the following Output is activated o X SY STEMS D
5. of access codes to allow access to your security system the stand alone code and the user access codes Stand alone Code default 123456 The stand alone code is the code that logs you on to the APR3 ADN2 This code does not give you access to your security system To do so you must then enter your user access code Ask your installer whether your stand alone code is 4 digits or 6 digits in length 4 Spectra User Manual User Access Codes The APR3 ADM2 uses your user access code to grant you access to your security system The user access code you would enter into your security system keypad is the same user access code you will use to enter on your telephone How Do I USE IT STEP 1 STEP 2 STEP 3 STEP 4 Pick up your telephone and dial your telephone number the telephone number of the line to which your APR3 ADM is connected The APR3 ADM2 asks you to enter your stand alone code Enter your stand alone code default 123456 After the voice prompt enter your user access code If your security system has not been partitioned proceed to STEP 5 If your security system has been partitioned keys 1 and 2 from your telephone represent partitions 1 and 2 just like your keypad To arm or disarm your security system press the desired partitions s number on your telephone InTouch 5 This will toggle the partition between armed to disarmed Refer to Example 1 on page 10 STEP 5 To activate or
6. our APR3 ADM2 s output can be used to turn on lights open or close a garage door and much more Ask your installer about this useful feature If the APR3 ADM2 s output is not enabled you will not be able to activate or deactivate the output Your installer can program the output to either deactivate manually or follow a timer If programmed to be deactivated manually InTouch 7 the output will remain activated until you deactivate it lf programmed to follow a timer the output will deactivate after the timer has elapsed When Entering Your Stand alone Code If the stand alone code is entered incorrectly after 3 consecutive attempts the APR3 ADM2 will immediately hang up When Using your APR3 ADM2 In some cases your telephone s tone may not be powerful enough to interrupt the APR3 ADM s voice prompt If this is the case simply wait for the APR3 ADM2 s voice prompt to finish before entering your action If your security system and APR3 ADM2 share the same telephone number you may be interrupted at times when using your APR3 ADM2 TELEPHONE PUSH BUTTON FEATURES Clear If you have made an error press the key on your telephone to clear the error and then re enter the information 8 Spectra User Manual Change Stand alone Code 8 To change the stand alone code default 123456 press the key and then press the 8 key from your telephone After the voice prompt enter your new
Download Pdf Manuals
Related Search