User's Manual - EZRecoveryCard
Contents
1. Legends Detailed description of the problems Analysis of possible causes Ways to solve the problems Further notes Caution I forgot the password Try default password first If that won t do please get the serial number password from your distributor As if no Ezrecovery card is plugged in After rebooting no installation menu appears and the computer starts OS as usual For the case the possible causes may be The card is not properly plugged The power supply has poor loading capacity CMOS is not properly configured The boot mode does not match BIOS Please refer to Boot Mode section in the Advanced Guide chapter to change the Boot Mode by pressing lt Ctrl B gt Plug the card again or change a slot or clean the slot the card Retry it with another ezrecovery card If the power supply does not 22 work contact your computer distributor or the manufacturer and replace either the power supply or the computer itself For some AMI BIOS motherboard set the CMOS parameter BIOS FEATURES SETUP as follows Set First boot device to LAN Or set Boot from LAN first to Enable Certain motherboards or BIOS may also require Set PnP OS installed to Yes Update BIOS There is little possibility that the above causes concur combinedly Improper CMOS configuration or Boot Mode not matching BIOS perhaps occurs with motherboards using AMI BIOS Displaying blue2. 21 I forgot the password 21 As if no ezrecovery card is plugged in 21 Displaying blue screen and Windows breaks down 22 4 Chapter 1 Introduction 1 1 Function An express installation can be performed by pressing the lt Enter gt key 3 times it cost you only five seconds Once hard disk data is destroyed by any mistake virus and or hacker only press lt 9 gt key one time to recover it in half a second Support IDE and SCSI hard disk controller Support PIO DMA33 DMA66 Ultra DMA66 ATA 100 Ultra ATA 100 IDE and SATA interface Support FAT16 16E FAT32 32E NTFS HPFS partitions and file systems Support 256GB hard disk Guarder whole hard disk or selected partitions Support multi OS booting by System Commander and multi bootable partition booting by BootMagic Support not only DOS Windows 3x 95 98 ME but also Windows NT 2000 XP 2003 server better Guard CMOS intelligently 1 2 Features When first set up saved or recovered the ezrecovery card uses only 5KB of hard disk when running it uses 1 33MB of hard disk at most Dynamic Virtual Hard Disk Drive DVHDD is one created and managed by the ezrecovery card in guarded partitions for new data saving Theoretically the ezrecovery card su
3. User s Manual http www ezrecoverycard com Disclaimer We have done our best to ensure that the material in this manual is both accurate and useful however please be aware that errors maybe exist and it dose not make any guarantee concerning the accuracy of information found here or in the use to which it may be put Before you install ezrecovery card please backup all your important files and ensure that it is stored separately CONTENTS CHAPTER 1 INTRODUCTION 4 1 1 Function 4 1 2 Features 4 CHAPTER 2 INSTALLATION 6 2 1 System requirements 6 2 2 Before installation 6 2 3 Start installation 6 2 3 1 Installation of driver for Windows 2000 NT XP software installation 6 2 3 2 Installation of ezrecovery card h
4. screen and Windows breaks down After rebooting PC displays blue screen with error message The free space in hard disks is limited There is no cache for the Ezrecovery card Anti Virus software or System Performance Administration software has been installed Recover the hard disk data or set it to Automatic Recovery Uninstall the Ezrecovery card Anti Virus software and System Performance Administration software Reinstall it after the system is Ok PC always requires to input SN password Ezrecovery card provides special anti evil uninstallation and haker affection if Ezrecovery card is not normally uninstalled it will require to input SN password before enter into OS Only after inputting correct SN password that is provided from your distributors You could enter into OS 23 If you have no SN password on hand please contact with your distributor in time for the solutions After installation of Ezrecovery card the PC always reboot before Windows loading Ezrecovery card provides three kinds of Boot mode each kind could meet difference BIOS setting After reboot Press lt Ctrl B gt just after CMOS setting list while before OS loading Ezrecovery card Boot mode menu will appear Choose the second or third Boot mode to try When I set hotkey menu as hidden how could I have it shown back when I want to check the Hotkey operation After reboot press lt
5. the correct password the following screen will appear 16 the default setting is protected all drives Press lt Tab gt to move and press lt Space Bar gt to mark or not mark V for every drive If there is mark of V this drive will be protected otherwise will not be protected 3 2 3 Set Parameters Menu Press lt 8 gt key in Hotkeys Menu the following screen will appear 17 The default settings are as the above settings You could set the recover interval from every 1 99 boot or every 1 2 day or every 1 99 days or every week or manual recover If you mark V in the item of manual with password that means you have to input password when you press lt 9 gt key to recover data otherwise you do not need If you mark V in the item of protect CMOS that means the setting of CMOS is protected If you mark V in the item of protect BIOS the BIOS will be protected otherwise not be protected If you mark V in the item of boot from HD only that means the computer has to boot from hard disk otherwise not If you choose Booting Display as none that means when the computer booting there will be no any screen about Ezrecovery card and the computer will enter directly operating system While you could get the Hotkeys Menu by pressing lt 8 gt key when booting your computer If you choose Booting Display as hotkeys the Hotkeys menu will appear when booting your computer The display
6. Ctrl M gt just after CMOS setting list while before OS loading and reconfig Ezrecovery card to show Hotkeys menu
7. ardware installation 6 2 4 Express test 9 CHAPTER 3 BASIC OPERATION GUIDE 10 3 1 Definition of terms 10 3 2 Operation Guide 10 3 2 1 Hotkeys Menu 10 3 2 2 Set Protected Partition Menu 15 3 2 3 Set Parameters Menu 16 3 2 4 Protect CMOS 17 3 2 5 How to modify the password 18 3 2 6 How to uninstall the ezrecovery card 19 3 3 Unique Serial Number and Serial Number Password 19 3 4 How to set Multi Boot 19 3 4 1 Setting Multi Bootable Partition Booting by BootMagic 19 3 4 2 Setting Multi OS Booting by System Commander 20 3 4 3 How to Skip Possible Virus Warning 20 CHAPTER 4 TROUBLESHOOTING
8. are installation and software installation separately for Ezrecovery card 2 3 1 Installation of driver for Windows 2000 NT XP 2003 software installation Boot the computer with Windows 2000 NT XP 2003 Run Install exe in the driver disk or CD supplied with the product Reboot your computer to complete the installation 2 3 2 Installation of ezrecovery card hardware installation Make your computer turn off Insert the card into one of empty PCI slots on the motherboard of the computer Turn on your computer Check the setting of CMOS to make sure the parameters of hard disk are 7 correct If there is Boot From LAN First or similar item enable it Disable the Virus Warning item in CMOS setting If there is a Hard Disk Recovery program in CMOS disable it Reboot your computer the following screen Installation menu will appear Installation Menu Press lt Enter gt key three times express installation will be finished with default parameters setting Press Install the following screen Set Parameters Menu will appear 8 Set Parameters Menu Press lt Tab gt key to move Press lt Space Bar gt or lt PgUp gt lt PgDn gt to modify the setting Press OK to save the setting and press Cancel to give up the change of setting Noted Without recovery if you choose it in Hotkey menu will appear this option the detail function kindly refer to 3 2 1 Hotkey menu After p
9. ing time could be modified from 15 seconds to 1 second the default time is 9 seconds You could press lt Tab gt to move from one item to another press lt Space Bar gt or lt PgUp gt lt PgDn gt to modify the setting 3 2 4 Protect CMOS If you choose protect CMOS in Set Parameters menu and if there are any changes for the setting of CMOS the following screen will appear Press Yes the changes of CMOS will be saved 18 Press No the changes of CMOS will be recovered Press Cancel the computer will reboot three times you could make any change for CMOM during the three reboots and all changes will be saved permanently 3 2 5 How to modify the password The default password is function all letters are in smaller case Press Change Password in the Set Parameters menu the following screen will appear After inputting the new password press lt Enter gt key the following screen will appear Input the new password again then press lt Enter gt key the following screen will appear Press OK the password is modified now If the two passwords you enter are not consistent or you pressed key Esc the following screen will appear to indicate that the password is not changed 19 3 2 6 How to uninstall ezrecovery card Press lt 0 gt key in Hotkeys Menu please refer to 3 2 1 3 3 Unique Serial Number and Serial Number Password If you press key F1 when entering the password the e
10. orrect password press lt Enter gt key to enter Set Protected Partition menu Press lt 0 gt key to uninstall The ezrecovery card After pressing lt 0 gt key the following screen will appear After inputting the correct password press lt Enter gt key the following screen will appear If you click Yes the ezrecovery card will automatically delete all the installation information then the following screen appears 14 Press lt 6 gt key to save the changes you made after last saving After pressing lt 6 gt key the following screen will appear After inputting the correct password press lt Enter gt key the following screen will appear Press Yes the following screen will appear then the computer will automatically reboot Press lt 9 gt key to recover the changes After pressing lt 9 gt key the following screen will appear After inputting the correct password press lt Enter gt key the following 15 screen will appear After pressing Yes you will enter into Operating System with all changed data will be recovered Press lt 8 gt key to enter Set Parameters menu in which you could set the parameters of Ezrecovery card After pressing lt 8 gt key the following screen will appear After inputting the correct password press lt Enter gt key to enter Set Parameter menu 3 2 2 Set Protected Partition Menu Press lt 5 gt key in Hotkeys Menu after inputting
11. pports a DVHDD of 1207GB practically it supports a 12GB one so it better supports Windows NT 2000 XP 2003 server and ensures that the Defrag routine can run and large data can be saved when any partition is guarded The magic Save function is best suitable for such application environment about government business institute home finance securities accounting and the military When any partition is guarded all 5 writing on it will be recorded as new data Once we use recovery or uninstallation function all new data will be cleaned The ezrecovery card provides Save function to write data onto hard disk Anti Evil Attack function is best suitable for cyber cafe and the computer labs of schools and colleges When the attacker deletes all installation information on the guarded partitions and reboots the computer the ezrecovery card will enter a Security Check routine OS can only be booted when the manager inputted the correct serial number password 6 Chapter 2 Installation 2 1 System requirements CPU 386 or above Memory 8M or more Hard disk IDE EIDE and SCSI 2 2 Before installation Make sure that your computer meets the above mentioned system requirements If a similar product has been installed remove it and its drivers Scan and clean viruses with anti virus software Make sure there is no static electricity 2 3 Start installation There are two steps of installation hardw
12. ressing OK the following screen will appear Set Protected Partition Menu 9 Set Protected Partition Menu Press lt Tab gt key to move Press lt Space Bar gt to modify the setting Press OK to save the setting and press Cancel to give up the change of setting After pressing OK The computer will reboot automatically Now you have finished the installation of the ezrecovery card 2 4 Express test Create a folder at the root of drive C and create another at Windows desktop Reboot your computer if the folders disappear it means that the ezrecovery card functions well and has automatically finished recovery 10 Chapter 3 Basic Operation Guide 3 1 Definition of terms Protected Mode General operators such as students are recommended to use this mode All useful data files or programs are set to be protected and will be protected under this mode All modification of the protected data will be recovered after Restore Data operation is executed Supervisor Mode The data on hard disk is not protected under this mode the operator can really install uninstall upgrade etc even if the drive is set to be protected Save Data If useful data are created under protected mode and need to be saved you can perform this operation to update the changes you made during last session Recover Data No matter how do you set the parameter you could recover data by press this hotkey lt 9 gt key Manual with pa
13. ssword If you select this item you have to input password after press lt 9 gt key otherwise you don t need password to recover data 3 2 Operation Guide 3 2 1 Hotkeys Menu When booting your computer with Ezrecovery card installed completely the following screen Hotkeys Menu will appear 11 If you choose Boot without recovery in set parameter menu the following screen will appear Pressing any key could stop the time counting Press lt Enter gt key you will enter protected mode in this mode all changes in the protected partitions will be protected Press lt Esc gt key the following screen will appear 12 After inputting the correct password press lt Enter gt key the following screen will appear Press Yes you will enter Operating System Press Ctrl Enter you will enter into Keep Mode it will not check the recovery interval Even if the recovery interval is Every 1 boot Keep Mode will keep data in the status of last shutdown or power off Notice If user press Ctrl Enter to use Boot without recovery then all changed data will be temporary saved in HDD If you want to enter into supervisor in next reboot kindly noted all changed data will be recovered Press lt 5 gt key to enter Set Protected Partition Menu in which you could set protection or not for each drive After pressing lt 5 gt key the following screen will appear 13 After inputting the c
14. zrecovery card will display its serial number 20040214 8899AABB CCDDEEFF 20040214 is the manufacture date of your ezrecovery card 8899AABB CCDDEEFF is the serial number It is unique By the serial number you can get the serial number password The serial number password is an all purpose password corresponding with your unique serial number it is used in case you forgot the password or the ezrecovery card carries security check to prevent evil attack and it can be only got from the distributors 3 4 How to set Multi Boot 3 4 1 Setting Multi Bootable Partition Booting by BootMagic BootMagic is a software packed with PQmagic It is specially used in installing Multi Bootable Partitions Please set HD partitions in PQmagic first and then install BootMagic OS 20 applications and the ezrecovery card in this order 3 4 2 Setting Multi OS Booting by System Commander At the first install OS and applications At the second install System Commander At last install the ezrecovery card 3 4 3 How to Skip Possible Virus Warning At the first time System Commander starts after the ezrecovery card installation the Possible Virus Warning window will appear as follows Press lt U gt key to update Reboot the computer and save hard disk data and then as long as you do not uninstall the ezrecovery card this window will not appear whenever you recover hard disk data 21 Chapter 4 Troubleshooting
Download Pdf Manuals
Related Search