IBDRW User Manual V1.0
Contents
1. Legacy USB Support Enabled BIOS Setting Description Setting options available only for EFI applications Support disable USB port Enable all the USB Enable l devices User can enable or USB 3 0 is enable USB 3 0 Support disable USB 3 0 XHCI Disable USB 3 0 is disable controller support This is a workaround for Disables this function XHCI Hand off OSes without XHCI Enable Enables this function hand off support This is a workaround for Disables this function EHCI Hand off OSes without ECHI Enable Enables this function hand off support USB mass User can Enable or Disables this function storage driver disable USB mass Enable Enables this function support storage driver support The time out value for USB Transfer Depends on the time out control bulk and time out value interrupt transfers USB mass storage Device Reset Depends on the time out device start unit time out value command time out Maximum time the Uses default value for a Device power up device will take before it root port itis 100 ms for a delay properly reports itself to Hub port the delay is taken the host controller from Hub descriptor 22 3 3 7 Chipset Setup Utility Copyright C 2013 American Megatrends Inc gt North Bridge 3 3 8 Chipset North Bridge Parameters Aptio Setup Utility Copyright 0 2013 American Megatrends Inc Intel IGD Confi2. from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient over voltage Never pour any liquid into an opening This could cause fire or electrical shock Never open the equipment For safety reasons only qualified service personnel should open the equipment If any of the following situations arises get the equipment check personnel n power cord or plug is damaged n Liquid has penetrated into the equipment n The equipment has been exposed to moisture n The equipment does not work well or you cannot get it to work according to user s manual gt The equipment has been dropped and damaged n The equipment has obvious signs of breakage UNMATE Donotleave this equipment in an uncontrolled environment where temperature is below 20 C 4 or above 60 C 140 F It may damage the equipment Caution Use recommended mounting apparatus to avoid risk of injury Warning Only use the connection cords which come along with the product when in doubt please contact the manufacturer Provision shall be made to provide transient protection devic
3. Securit ave 8 11 System Time 18 sowing Description Soning options Eroi This 15 current time setting The time is mE mE Adjustment of the Set the time in the System Time maintained by the format hh mm ss battery when the device is turned off This is current date setting The time is Set the date in the Changes to the System Date maintained by the format ate battery when the device mm dd yyyy is turned off Set the language in other language This is current language Adjustment of the System Language The language setting language uu this device is English 3 3 4 BIOS Advance Setup Utility Enable and disable BIOS support for Intel Active Management Intel AMT Support Technology Enable and disable the boot interruption lt Ctrl P gt to call up Intel Intel AMT Setup Prompt Management Engine BIOS Extention configuration Enable Client Initiated Remote Access CIRA Fast Call for Help AMT CIRA Request Trig CIRA allows AMT maintenance event if the AMT PC is not in the Intranet CIRA timeout for connection establishment with MPS AMT CIRA Timeout Manageability Presence Server vPro Enabled Gateway Resets all the values of the MEBx to their defaults see section Un Configure ME Reset with Un Configure USB Configure USB Configure E Enable and disable the USB configuratio
4. critical location While IBDRW Ex is ATEX and Class 1 Division 2 certified DIN Rail Box pc for hazardous location deployment and for ATEX certified Box PC requires special enclosure box 1 2 Hardware Specification 1 2 1 System Specification Processor Intel amp Celeron Bay Trail M oystem Chipset Bay Trail SoC Chipset System Memory 1 x DDR3L 1333MHz SO DIMM 2GB max 8GB Ethernet Controller 4 x Intel OMG82574L LAN USB 1 x USB 3 0 3 x USB 2 0 external 2 x USB 2 0 by pin header internal Storage Default 32GB mSATA SSD Second Storage optional 2 5 SSD 64 512GB 1 2 2 Mechanical and Power Dimensions 85 5mm x 152mm x 139mm Lx W x H Construction Aluminum Housing Power Input 9 36V DC IN isolation Power Source Range 20W max Mounting DIN Rail 1 2 3 Connectors Front Side I O 1 x Power ON OFF button with LED indicator 1 x Line Out Line In Mic In 4 x RJ 45 Giga LAN 1 x RS232 default 422 485 as optional 1x VGA 1 x USB3 0 3 x USB2 0 1 x DC Power Terminal Block 1 x 5232 default Isolated RS232 485 as optional 1 x 20 pins terminal block DIDO 1 2 4 Environment Considerations Operating Temperature 20 to 60 deg C Operating Humidity 5 to 95 non condensing Anti Vibration oHz 500Hz 1 Grms 3 Axis 1 3 Packing List e 1 x DIN Rail Mounting clip 1 x User Manual 1 x 12V AC to DC Power Adapter with power cord 1 x System Re
5. 13 14 CHAPTER 3 INITIAL SETUP Li 15 3 1 DIN Rail Mounting Set 15 3 2 Cable ARM Bracket Installation optional for IBDR Ex 16 99 Configuration ofthe BIOS ip bruit Uo e aiaa 17 3 3 1 BIOS setup and Boot 17 222 BIOS Sell 0 IM Ma EAM 17 MAN 18 3 3 4 BIOS Advance Setup 19 20 VERT NN 21 NNN 23 3 3 8 Chipset North Bridge Parameters 23 3 3 9 Chipset South Bridge 24 25210 PEN F 25 3 3 11 Security Boot 27 EG DE E RD NES 28 ENE 29 AL 31 Chapter 1 Winmate IBDRW IBDRW Ex Overview 1 1 Introduction Winmate IBDRW is a DIN rail mounted Fanless Box PC which provides several serial communication ports With a compact size and small form factor as well as front accessible I Os Winmate IBDR is very convenient for wiring and DIN rail installation in the control cabinet The Wide operation temperature and Industrial serial port design makes this unit a perfect communication even in harsh and
6. 2 1 14 Clear CMOS 1 2 Clear CMOS 2 3 Normal 2 1 15 5422 RS485 Terminal Resistor B 1 2 120 ohm 2 1 16 85422 RS485 1 2 5485 2 3 RS422 2 1 17 5232 RS422 5485 Jumper RSm 2 3 2 3 JP9 3x4 14 Chapter 3 Initial Setup 31 DIN Rail Mounting Setup Please follow these steps to mount the IBDRW hook kit on a DIN rail 1 Screw the provided DIN rail Kit on the rear side of the box as the diagram shown below 2 Please make sure the stiff metal handle part is located on the top UNMATE 3 2 Cable ARM Bracket Installation optional for IBDR Ex In hazardous locations sparks caused by the movement from a cable and connector which is even slightly loose could lead to a disaster and to prevent this cable arm bracket can be use to secure some LAN USB and Audio connectors Follow these steps to complete the installation y 1 1 Find the cable arm bracket in the package including the plate bracket holder and screws Install the plate on the top of the box and screw it tightly Plug all the necessary cables into the connectors Place the cable arm bracket according to the picture and then attach the bracket holders to the plate and then screw it for securing the installed cables A For ATEX deployment it is require to have Enclosure box Note 16 3 3 Configuration of the BIOS 3 3 1 BIOS setup and B
7. AN3 1287 2 lt 4 5 6 7 8 9 2 Signal LAN1 MDIO IN LAN1 MDIO IN LAN1 IN LAN1 IN LAN1 MDI2 IN LAN1 MDI2 IN LAN1 MDI3 IN LAN1 MDI3 IN DGND LAN1 VDD33 LAN1 ACTIVE Y LAN1 1000 O LAN1 100 10 G 2 1 8 Dual LAN Pin Signal Name Pin Signal Name 6 LANG MDIZIN 24 LANSVDD33 LAN3 MDI3 IN 1000 O 9 NA 27 ACTNE Y 20 LANA MDIO IN LAN GND 12 IN LAN ry 13 IN LAN GND 14 IN 2 2 1 9 COM VGA Signal Name DCD4 485TXRX Vi R FILTER SRD4 485TXRX G FILTER STD4 422RX B_FILTER DTR4 422RX O M __ OMD _ __ OMD _ NA GND GND GND GND GND V2 V3 V4 V5 V6 V7 V8 V9 VGA 5V 2 1 10 Audio Pin Signal Name Pin Signal Name _ TT AUGND 2 9 AUGND de so 2 1 11 DIDO Pin SignalName Pin Signal GND 8 2 9 DN 6 200 18 2 1 12 5422 RS485 Pim Signal Name Pin Signal Name af wo 8 DINT 1 wow fe owe 2 1 13 Isolator DIDO Pin Signal Name Pin Signal Name gt i ov 6 3 me a 4 porero
8. DIN Box PC Intel Celeron Bay Trail M IBDRW IBDRW Ex User Manual Version 1 0 Contents CHAPTER 1 WINMATE IBDRW IBDRW EX OVERVIEW 4 1 1 Moll mmm 4 1 2 Hardware issenensis i etes ni saaie ee ea 4 1 2 1 System 4 1 2 2 Mechanical and 4 123 COPD IGCIDIS E 5 1 2 4 Environment 5 149 PACK 5 1 4 5 1 5 Chassis DINE ST ne 7 CHAPTER 2 HARDWARE FUNCTIONALITY 8 2 1 Winmate IBDRW IBDRW Ex 8 1 DANTE 8 2 1 2 DE ROAST 15 8 1 LC 9 12 DEN 9 215 9 GDS 10 2 1 7 USB 2 0 USB 3 0 LAN 9 10 ALS DJALAN 11 218 MENN 11 _______ 12 DD 12 25112 RTR 12 2113 BRT 13 718 ET NS 13 2 115 5422 RS485 Terminal 2 2 13 2116 9422 eee ee
9. covery DVD optional Terminal block female connectors Cable Arm Bracket Optional for IBDR Ex 1 4 Safety Precaution WARNING Always completely disconnect the power cord from your chassis whenever you work with the hardware Do not make connections while the power is on Sensitive electronic components can be damaged by sudden power surges Only experienced electronics personnel should open the PC chassis CAUTION Always ground yourself to remove any static charge before touching the CPU card Modern electronic devices are very sensitive to static electric charges As a safety precaution use a grounding wrist strap at all times Place all electronic components in a static dissipative surface or static shielded bag when they are not in the chassis SAFETY PRECAUTIONS Please read this safety instruction carefully Place keep this user s manual for later reference Please disconnect this equipment for any AC outlet before cleaning Use liquid or spray detergents for cleaning Use a damp cloth Do not touch the LCD panel surface with sharp or hard objects For pluggable equipment the power outlet must be installed near the equipment and must be easily accessible Keep this equipment away from humidity Place this equipment on a reliable surface during installation dropping letting it fall could cause damage The openings on the enclosure are for air convection Protect the equipment
10. cure Boot state Enables this Enable function Disables this Disable Allows user to configure function Secure Boot Mode the secure boot mode Enables this Enable function Enroll all factory default keys Platform Provides user with key key exchange configuration options for key Authorized Select the Key Management secure boot key signatures desired key management Authorized timestamps Forbidden signatures 21 3 3 12 Boot Setup Utility Copyright C 2013 American Megatrends Inc Setup Prompt Timeout BIOS Setting Description Setting options Allows user to configure the number of seconds to stay Set the prompt Setup Prompt Timeout BIOS setup prompt timeout screen Numlock feature on the Boot NumLock State numeric keypad of the keyboard after the POST Off Remains Off Default On Determines if POST Disables this Disabled message OEM logo function Quite Boot default Black Enables this Enabled background is displayed function Disables this Enables or disables Fast Disable function Fast Boot Boot to shorten the OS boot Enables this process Default Disabled Enable function 28 Specifies the overall boot Ex Hard drive as Boot Option Priority order from the available Boot Option 1 the first priority devices hard drive Specifies the boot order for Enter the a specific device type such sub
11. e to be set at a level not exceeding 14096 of the rated voltage at the power supply terminals of the apparatus Warning Explosion Hazard Do not disconnect equipment unless power has been switched off or the area is known to be non hazardous Warning The equipment should be adequately protected from direct light when installed indoor or outdoor 1 5 Chassis Dimension 139 0 5 H L Chapter 2 Hardware Functionality 2 1 Winmate IBDRW IBDRW Ex Peripherals The following figures show the connectors on Winmate IBDRW and the following sections give you detailed information about function of each peripheral 2 1 1 DC Adapter Jack Pin Signal Name Adapter Adapter DC 2 1 2 DC Adapter Jack Pin name Pin Signal Name gt USB TX2 GND TX3 USB TX4 GND LEDGND TX1 GLED 2 1 3 1 00000 GND 8 V smum o w _ Pin Signa Name Pin Signal Name af as s 2 1 4 DVI Connector Pin Signal ome GND GND GND GND Ls Dam 16 nomenet fv ie ves 2 1 5 Mini PCIe 2 1 6 SSD 2 1 7 USB 2 0 USB 3 0 LAN Connector Signal Name Pin 2 9 5 6 ge 13 10 U3TXDN1 U3TXDP1 0000 5VUSB3 0 29 2 pen N89607501 Cy USBL
12. ed Express Enable Disable port 3 this function Disables this Disable function Enables this Enable function The System configuration Configures high precision High Precision Timer timer HPET in the operating system stays off upon Power Off the return of the AC power The System is turned on upon Configures the state of the Power On the return of the Restore AC Power Loss system after return of power AC power on AC power loss The system returns to its last known awake Last State state upon the return of the AC power Entering quite Quite active mode Serial IRQ Mode Configures IRQ mode Entering Continuous Continuous idle mode 3 3 10 Security Allows user to configure an administration or user password user must enter the administrator or user password at system startup and when entering BIOS setup 25 Winmare Aptio Setup Utility Copyright C 2013 American Megatrends Inc gt Secure Boot menu BIOS Setting Administrator Password User Password Description Setting options Displays whether or not an administrator password has Enter Password been set Display whether or not a Enter Password user password has been set 26 INMATE 3 3 11 Security Boot Menu aptio Setup Utility Copyright C 2013 American Megatrends Inc Secure Boot Disabled Disables this Disable l Displays the current boot function Se
13. gnetic Compatibility Directive European for Industrial Control Equipment Self Declaration in accordance with EMC Directive 2004 108 EC Independent 3rd party assessment Accredited by IEC 17025 31 Federal Communications Commission on electromagnetic interference C This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may cause harmful and 2 this device must accept any interference received including that may cause undesired operation 32
14. guration BIOS Setting Description Setting options Provides onboard Opens Intel IGD Configuration graphics related submenu 25 Vinmare Tommros Configures IGD LCD Opens IGD LCD Control Enter setting submenu Provides power saving Graphic Power Opens configuration options for the Management Control onboard graphics 3 3 9 Chipset South Bridge Parameters Aptio Setup Utility Copyright 0 2013 American Megatrends Inc gt Azalia HD Audio BIOS Setting Description Setting options Disables this Disable Configures onboard audio function Azalia HD Audio function Enables this Enable function Provides user with Enable Disable USB Configuration USB 2 0 EHCI configuration options for the this function USB controller such as Enable Disable mE USB Port 0 enabling disabling a this function specific USB port and Enable Disable USB Port 1 support for certain features this function Enable Disable USB Port 2 this function 24 Win Enable Disable USB Port 3 this function Express Enable Disable Provides user with port 0 this function configuration options for the Express Enable Disable Express bus such as 55 mM port 1 this function enabling disabling Configuration Express Enable Disable a specific PCI Express port 2 this function channel and spe
15. menu that as hard drives optical present the Hard Drive BBS Priority drives floppy disk drives devices of the and devices that support same type are Boot from LAN function connected 3 3 13 Save amp Exit Aptio Setup Utility Copyright iC 2013 American Megatrends Inc Save Changes and Exit Setting BIOS Setting Description options Saves the Enter Yes This saves the changes to changes save Changes and Exit the CMOS and exits the Return to the BIOS Setup program Esc No BIOS Setup Main Menu This exits the BIOS Setup saves the Discard Changes and Exit Enter Yes without saving the changes changes 29 Return to the in BIOS Setup to the CMOS Esc lt No gt BIOS Setup Main Menu Saves the Enter lt Yes gt changes Return to the Esc lt No gt BIOS Setup Main Menu Saves the Enter lt Yes gt changes Return to the Esc lt No gt BIOS Setup Main Menu Saves the Enter lt Yes gt changes Return to the Esc lt No gt BIOS Setup Main Menu Saves the Enter lt Yes gt changes Reset the system after save Changes and Reset saving the changes Discard Changes and Reset system setup without Reset saving any changes Save changes done so far Save Changes to any of the setup options Discard changes done so Discard Changes far to any of the setup Return to the options Esc lt No gt BIOS Setup Main Menu Saves the E
16. n provisioning e 3 3 5 Advanced Setup Utility Copyright 2013 American Megatrends Inc Settings BIOS Setting Description Setting options 5 ACPI Settings Configures ACPI settings Enter submenu 5 SMART Settings Configures SMART settings Enter submenu Configures System Super IO Opens Super IO Configuration Enter Chip parameters submenu Opens Hardware Monitor Monitor hardware status Enter submenu 5 CPU Configuration Configures CPU settings Enter submenu 5 PPM Configuration Configures PPM Parameters Enter submenu Configures Thermal Opens Thermal Configuration Enter Parameters submenu Opens IDE Configuration Configures IDE devices Enter submenu 20 Vin INMATE LPSS amp SCC 5 Configures LPSS SCC Enter Configuration submenu Network Stack Opens Configures network stack Enter Configuration submenu Configures CSM Opens CSM Configuration Enable Disable Option ROM submenu execution settings etc Opens CMOS CMOS settings Information Enter submenu 5 Trusting Computing Trusted computing settings Enter submenu T 5 USB Configuration Configures USB settings Enter submenu Opens Platform Trust Technology Platform trust technology Enter submenu 3 3 6 USB Configuration Setup Utility Copyright 2013 American Hegatrends Inc
17. nter lt Yes gt changes Restore load default values Restore Default Return to the Esc lt No gt BIOS Setup Main Menu Saves the Enter lt Yes gt changes Return to the Esc lt No gt BIOS Setup Main Menu Saves the Enter lt Yes gt changes Return to the Esc lt No gt BIOS Setup for all the setup options Save the changes done so Save as User Defaults far as User defaults Restore the User Defaults to Restore User Defaults all the setup options Main Menu 30 APPENDIX Refer the following descriptions for various approvals and certifications N A Safety for Information Technology Equipment optional for IBDRW Ex UL Certification by Underwriter Laboratories to UL60950 1 27 25 5 Edition standard and equivalent CSA 22 2 60950 1 07 LISTED 274 Edition Standard Safety for HazLoc Class 1 Division 2 Groups A B C D 4 optional for IBDRW Ex ITE FOR USE IN Certification by Underwriter 10 LOC ANSI ISA 12 12 01 2012 standard equivalent E361897 CAN CSA 22 2 213 M1987 Standard Explosive Atmosphere Directive optional for IBDRW Ex Certification with ATEX Directive 94 9 EC Independent 3rd party assessment Low Voltage Directive European Safety for Industrial Control Equipment Self Declaration in accordance with European LVD Directive 2006 95 Independent 3rd party assessment Accredited by IEC 17025 Electroma
18. oot Procedure BIOS stands for Basic Input Output System and it is the most basic communication between user and the hardware To enter BIOS Setup the DEL key must be pressed after the USB controller has been initialized as soon as the following message appears on the monitor during Power On Self Test POST Press DEL to run SETUP Note Update BIOS version may be published after the manual is released Please check with the latest version of BIOS on the website User may need to run BIOS setup utility for the following status 1 Error message on screen indicate to check BIOS Setup 2 Restoring the Factory default setting 3 Modifing the specific hardware specification 4 Want to optimize the specification 3 3 2 BIOS Setup Keys The following keys are enabled during POST Key Function Del Enters the BIOS setup menu Display the boot menu Lists all bootable devices that are connected to the system With cursor 1 and cursor and by pressing lt gt select the device used for the boot B Pressing the Pause key stops the POST Press any other key to ause resume the POST The following keys can be used after entering the BIOS Setup ky Function o O 1 3 3 3 MAIN Immediately after the DEL key is pressed during startup the main BIOS setup menu appears Aptio Setup Utility Copyright 0 2013 American Megatrends Inc 11051
Download Pdf Manuals
Related Search