Dominator Safes User Guide A5s
Contents
1. 15 15 OPENING THE SAFE USING TIME DELAY To activate the time delay period press any button The lock will enter into the preset delay period and the led will flash an orange light every 5 seconds In the last 10 seconds the light will flash quickly and end with 2 beeps Once the beeps have sounded there is a 2 minute window for the user to enter their code to open the safe If the code is not entered within 2 minutes the lock will reset and the procedure will have to be restarted to open the safe DELETING THE TIME DELAY FUNCTION To remove the time delay function you have to set the delay period to 0 minutes Only the master code can delete the time delay function e Press mastercode 00 00 SETTING THE DUAL CONTROL MODE The lock can be set to require 2 codes to open the safe This can be set as any 2 codes or as one user code and one supervisor code Only the master code can set dual control mode For standard dual control mode e Press mastercode 1 1 For supervisor dual control mode e Press mastercode 2 2 OPENING THE SAFE IN DUAL CONTROL MODE LOW BATTERY INDICATOR CHANGING BATTERIES To open the safe in standard dual control mode e Press codel code2 this can be any 2 codes To open the safe in supervisor dual control mode e Press codel code2 one of the code must be either the supervisor code or the master code Note There is an allowance of 60 seconds between entering the first and seco2. a DOMINATOR SAFES user Quide Distributed by Centurion International Wholesalers Pte Ltd 52 Horne Road 02 01 Singapore 209071 www dominatorsafes com au OPENING THE SAFE Opening the safe can be done by any code master supervisor or user Code e Press Code e Turn the handle to retract the locking bolts Lock will beep and display green indicator when successful code has been entered E G if code is 777777 press 777777 LOCKING THE SAFE The digital lock will automatically lock after 5 seconds Close the door and turn handle to extend the locking bolts Note Always test that handle is locked before leaving safe CHANGING CODES There are two codes preset to the safe from the factory a master code and a supervisor code The preset master code is 777777 and the preset supervisor code is 0000 If you choose to only use one code you will need to delete the supervisor code from position 2 using the deleting codes procedure All codes can be changed from factory setting You can select any code from 1 10 digits in length Codes are issued an allocated ID number The master code is ID number 1 The supervisor code is ID number 2 The user codes are ID numbers 3 7 Note When changing any code it is very important to make sure the door is left ajar to prevent accidental lockout CHANGING THE MASTER CODE To change the master code from the factory setting e Press exis
3. nd code The Dominator digital includes a low battery indicator which will show when the batteries need to be replaced When a correct code is input the indicator light will turn orange and then green The lock will continue to function for around 30 uses The batteries are located behind the keypad on the outside of the safe Grasp the keypad and rotate anti clockwise approximately 35 degrees until keypad comes off Do not let the keypad hang from the wires The lock requires 4 x AAA batteries which need to be positioned according to the diagram Once batteries are inserted correctly the lock will sound indicating there is power to the lock Replace the keypad in the same way it was removed ensuring the wires are not being pinched Turn the keypad approx 30 degrees clockwise until it is upright INCORRECT CODE LOCKOUT TIMER All Dominator digitals have a lockout or paralysis function to reduce the chance of a code being guessed The lock will allow 3 incorrect entries before it will enter a 5 min lockout period where no codes can be entered After the 5 minutes codes can again be entered
4. tingmastercode newmastercode newmastercode E G if you want to change the master code to 123456 Press 777777 1 123456 123456 CHANGING CODE USING THE MASTER CODE All codes can be changed by using the master code Press mastercode allocatediDnumber newcode newcode The lock will sound a single beep and flash an orange light E G if you want to change user code number 4 to 1234 and your master code is 777777 Press 777777 4 234 1234 Note If any part of the code change sequence is done incorrectly the lock will remain at its current settings CHANGING USER CODES USING SUPERVISOR CODE The supervisor has the ability to change user codes but not the master code e Press supervisorcode allocatediDnumber newcode newcode The lock will sound a single beep and flash an orange light E G If you want to change code number 4 to 1234 and your supervisor code is 0000 Press 0000 4 1234 1234 DELETING CODES Only the master code can delete another code e Press mastercode allocatediIDnumber E G If you want to delete code number 4 Press 777777 4 SETTING TIME DELAY The time delay function allows the user to set a period of time in which the user must wait to open the safe The delay time is adjustable from 0 99 minutes Only the master code can set the time delay period e Press mastercode 01 99 01 99 E G If you want to set the delay period to 15 minutes Press 777777
Download Pdf Manuals
Related Search