Home
Electrician Installation Manual National Warranty Line
Contents
1. 6 Switch Cover 1 2 Assembling the fan Blade S STEP 6 Fig 7 a ae en a Attach blades to the blade holders on the Ta Blade Washer motor housing using the 3 screws and H washers provided Blade b Repeat this procedure for the other 3 blades STEP 7 Fig 8 a Lift the switch cover to expose the reverse switch b The reverse switch should be pushed fully to the left for Summer fan spins anticlockwise and pushed fully to the right for Winter fan spins clock wise c Make the sure reverse switch is not stuck in its neutral position otherwise the fan will not spin Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC INTERNATIONAL Attaching an accesso Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan ight kits Aurora2 light kit 78mm halogen light MAX 100W Lower Rim Screws STEP 1 Fig 9 a Turn base plate to remove the plug and base plate from the motor housing b Loosen screws to remove the lower rim STEP 2 Fig 10 a Use the connectors to attach the light wires from the motor housing to
2. Insert the down rod pin into the connection collar and the down rod cotter pin avoid pinch ing wires Clip in the cotter pin key and secure down rod with the other shorter down rod screw provided d Slide on canopy cover and refit the ball joint If an extension rod needs to be installed please go to page 11 STEP 2 Fig 2 a Drill a hole in the timber nogging for wiring b Use the two hex screws to secure the hanger bracket onto the timber nogging The timber nog ging should be supplied by the installing electri cian and must be supported between the two ceil ing joists as shown in the diagram above STEP 3 Fig 3 a TIGHTEN THE GRUB SCREW This is important to ensure the fan will not wobble and the weight of the fan is supported b Hang the ball joint into the hanger bracket Ensure the groove on the hanger bracket is locked into the slot on the ball joint Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL Green yellow Separate terminal For when 3 pole Blo
3. certain types of installation After installation fan blades must be at least 2 1 m 7 feet above floor level The use of these products by children and the infirm must be under supervision IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY HOT LINE NUMBER 1300 360 280 BEFORE LEAVING THE JOB SITE PLEASE DO NOT REMOVE THE FAN FROM THE CEILING ONCE INSTALLED UNLESS INSTRUCTED TO DO SO HUNTER PACIFIC Electrician Installation Manual Aurora Alternative 2 Ceiling Fan INTERNATIONAL Parts List Aurora Alternatives 2 Le i a H N J Pe al Hex Head Screw ZZ Blade Screw Motor Housing Lower Rim Base Plate m iw Ball Joint Screw Down Rod Pin Screw th P bled ese parts come preassemble Ball Joint Pin Down Rod Short Screw HUNTER PACIFIC INTERNATIONAL Assembling the fan Washer m Cotter Key Down Rod Screw Timber Nogging 2 WARNING 4 __ Ball Joint Reverse Switch Cover be Connection Collar _ Cotter Pin Hanger Bracket Hex Head Screw Down Rod Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan STEP 1 Fig 1 PERFORM THIS STEP IF THE WIRES HAVE NOT BEEN FED THROUGH THE DOWN ROD a Loosen the ball joint screw and remove the ball joint pin to separate the down rod from the ball joint b Feed wires from motor housing up and through the down rod c
4. light assembly kit b Attach and secure the light assembly kit using the 3 screws provided Groove Glass Cover STEP 3 Fig 11 a Plug the light globe into the socket DO NOT touch the light globe with your fingers b Gently push the glass cover upwards and turn it to attach the light glass to the fan 2 WARNING E14 light MAX 2x40W Screws Lower Rim STEP 1 Fig 12 a Turn base plate to remove the plug and base plate from the motor housing b Loosen screws to remove the lower rim Light wire connectors Lower STEP 2 Fig 13 a Use the connectors to attach the light wires from the motor housing to light assembly kit b Attach and secure the light assembly kit using the 3 screws provided N Groov e Glass Cover STEP 3 Fig 14 a Install the light bulbs in the light sockets b Gently push the glass cover upwards and turn it to attach the light glass to the fan Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL Attaching a
5. the light kit b Secure upper part of the light kit to the motor housing by tightening the thread c Connect light wires to the terminal block in the lower part of the light kit d Secure the lower part of the light kit to the upper part of the light kit by the tightening the light kit screws e Fit light globes in to the light kit note Only specified globes should be used 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty d 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL Attaching an extension rod Hunter Pacific rods to be used ONLY N _ Ball Joint Canopy Cover Reverse Switch Cover Washers Cotter Key 3 Jr Connection Collar Ball Joint Down Rod _ Cotter Pin Screw Down Rod Step 1 Fig 24 Step 2 Fig 25 Loosen and remove the down rod screws and Loosen the ball joint screw take out the ball joint the down rod pin screw to remove the pin and remove the ball joint Then slide off the standard down rod from the motor housing canopy cover __ Ball Joint Ball J
6. HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan IN TERNATIONAL Mora miserae i CEILING FAN MUST BE INSTALLED BY ALICENSED ELECTRICIAN NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN Electricians are recommended to tick off all items on the quick checklist and fill out their details onto the back page of the Fan Owner Warranty amp Operations Manual after installation ELECTRICIANS TO PROTECT YOUR CUSTOMER S WARRANTY PLEASE READ PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Hunter Pacific International Pty Ltd Building 8 256 New Line Road Dural NSW 2158 Australia ABN 18 063 521 666 HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL IMPORTANT INFORMATION ELECTRICIANS MUST READ PRIOR TO INSTALLATION 1 Distributor and installer details and purchase receipts are essential for on site warranty claims and must be presented to repair personnel make sure you record your details in the Fan Owner Warranty and Operations Manual 2 Fans and fixed wiring products must only be installed by persons who are appropriately licensed by the applicable State regulatory body Therefore to protect our repair personnel on site warranty claims will not be accepted if products have been installed by unlicensed persons 3 Da
7. ck is fitted 2 WARNING 1 White or Red Assembling the fan STEP 4 Fig 4 amp 5 a Connect wires from the fan to wires in the ceiling via the terminal block on the hanger bracket refer to figure 4 and 5 b Make sure earth wires are also connected c Connect light wires red white if a light fitting is going to be used Cap seal light wires if a light fitting is not going to be used 6 T T l D Combi Separate 5 Control Control FA LAE N Wiring for use with 3 pole block Colours representative only Separate extension terminal for active for light when 3 pole block fitted Fan Wiring ke STEP 5 Fig 6 aa a Slide canopy cover up and over the hanger bracket b Twist the canopy to locate screws holes then loosen canopy screws half way c Now twist the canopy cover in the opposite direction and fully tighten screws until the can opy cover is stabilised Down Rod Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL WARNING
8. contact If it is a Typhoon fan check and ensure the reversing switch plate under the switch cover is not bent also check the 3 wires coming from the switch plate are straight Occasionally the switch plate may get bent during transportation this allows the switch cover to press against the plate and stop the fan from working If it is a Typhoon fan check the nine pin plug under the switch cover is properly connected and the colours on the plug are corresponding If it is a Concept fan and it has an external start up capacitor check that this external capacitor is properly connected Fan speed does not correspond to the wall controller Check the speeds on the wall controller has been wired correctly and are making proper contact Brown speed 1 Purple speed 2 Red speed 3 Check wires in the terminal block are connected properly connection wires should be stripped back at the connection point and unused wires should be sealed and capped off Check that the reversing switch is pushed into its Summer or Winter position Fan is not responding to the remote control Check for flat battery Make sure the dipswitch settings in the hand piece and the remote receiver for the same fan are corresponding Fan is wobbling Check the ball joint slot is locked into the hanger bracket groove Make sure blades are a matching set the letters on matching sets of blades should be identical with the numbers varying within 3 grams of each other C
9. heck blade screws are tightened firmly If necessary use balancing kit provided to settle the wobble Fan is noisy 1 2 WARNING Check all screws and parts are secured firmly Ensure there are no loose parts moving inside the motor housing Make sure the fan is installed with a Hunter Pacific wall controller only do not use solid state controllers as they can cause unpleasant motor noises National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 12 HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL WARNING 13 Trouble Shooting Tips Light Light will not turn on Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit the terminal block in the canopy cover and the wall switch has been connected together correctly Light is not responding to remote control Make sure globe has not blown and it is properly fitted between the metal prongs Check all l
10. ight wires in the light kit the terminal block in the canopy cover and the wall switch has been connected together correctly Check dip switch settings in remote hand piece and remote receiver correspond Light wires appear to be missing or too short Wires may be stuck in the motor housing Carefully pull wires out of the motor housing careful not to strip the wires as this may cause the fan to short Light flickers or flashes Check globe is secured between the metal prongs in the light kit Make sure you are using the globes specified National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 1 Do not attempt to operate the fan or optional light kit with any wall control that is not 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Fan INTERNATIONAL Quick Checklist Electricians make sure everything on this checklist is ticked off before you leave the installation site If you have trouble installing our product please refer to the trouble shooting section on the previous page first then phone the Hunter Pacific Warranty Line on 1300 360 280 o
11. mage caused by incorrect installation force majeure electrical surges lightning power grid fluctuations water or by connection to alternative power supply sources such as solar inverters etc is not eligible for warranty repair 4 Blades must be replaced only as a complete set Blades are supplied only as a pre balanced set and the replacement of individual blades may void the warranty by causing mechanical damage to the motor excessive noise or premature wear 5 When products are installed in a location requiring special access equipment Such as scaffolding or scissor lifts etc the cost of providing installing and operating special access equipment must be borne by the site owner For safety and to protect your customers warranty the following must be taken into account when installing and operating the product s a DO NOT USE SOLID STATE WALL CONTROLLERS Neither leading nor lagging edge controllers will give satisfactory performance Wall controls must only be types approved for use by Hunter Pacific International The fan light and bracket must be earthed Fan and light must be run from the same phase and preferably the same final circuit Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for
12. n accessory light kit Aurora2 light kit Screws GX53M 14W compact fluorescent light STEP 1 Fig 15 a Turn base plate to remove the plug and base plate from the motor housing b Loosen screws to remove the lower rim Lower Rim STEP 2 Fig 16 a Use the connectors to attach the light wires from the motor housing to light assembly kit b Attach and secure the light assembly kit using the 3 screws provided Glass Cover _ Fluorescent Light STEP 4 Fig 18 STEP 3 Fia 17 a Turn the light to attach it firmly to the light a Fit the compact fluorescent light to the socket light socket b Gently push the glass cover upwards and WARNING 8 1 2 turn it to attach glass cover to the fan Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL Attaching an accessory light kit Standard accessory light kit AN Motor Housing NS We Lower Rim Base Plate Plug Screws STEP 2 Fig 20 STEP 1 Fig 19 a Loosen screws to remove the light kit rim a Turn base plate anticlockwise to remove the pl
13. oint Pin ___ Canopy Cover Ball Joint R M Reverse Tighten Ball a Switch Cover Joint Screw Washer s a Cotter Key Connection Collar Down Rod Down Rod 7 Cotter Pin Screw Step 3 Fig 26 amp 27 Now install the extension rod and reverse step 1 amp 2 to secure the rod to the fan and the ball joint NOTE If the extension rod needs to be shortened cut the rod to the required length and drill the appropriate hole size to fit the ball joint pin The cut end of the rod should be used on the ball joint end only When installing a 1 8m extension rod the wiring will need to be extended and joined This should be done using crimp style connectors 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty d 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set 11 HUNTER PACIFIC Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan INTERNATIONAL Trouble Shooting Tips Fan Fan will not start Check that the reversing switch is pushed fully into its Summer or Winter position Check wire connections in the wall switch and terminal blocks ensure all wires are making proper
14. pen 9am to 5pm EST DO NOT uninstall the fan and DO NOT return fan to retailer 10 Ceiling fan is not installed to a solid state wall controller Neither leading nor lagging edge controllers will give satisfactory performance Wall controllers must only be types approved for use by Hunter Pacific International The fan optional fan light and bracket is earthed Fan and optional fan light are run from the same final circuit Mounting bracket must be firmly secured to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation Fan blades are at least 2 1m feet above floor level Check the fan is operating correctly on all three speeds using the wall controller If light is installed Check light switch is functioning properly If remote control is installed Check the fan and light if installed is responding to the remote control correctly Write Dip switch code in user guide If remote control is installed Check where possible a separate isolation switch has been installed for the fan Check electrician s details have been recorded onto the back page of the Owner s Operations and Warranty Manual 14
15. ug and base plate from the motor housing Do not throw away base plate away STEP 3 Fig 21 a Once the motor housing lower rim is removed the light wires coming from the motor housing should be exposed b Cut and remove wire connectors c After removing the wire connectors feed the light wires through the thread of the motor housing lower rim d Tighten screws removed from step 2 to Cut and remove secure the motor housing lower rim back wire connectors onto the motor housing upper rim Lower Rim 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty e 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If eee only one blade is damaged you are still required to replace with a new set 9 HUNTER PACIFIC INTERNATIONAL Attaching an accessory light kit a standard accessory light kit Electrician Installation Manual Aurora Alternatives 2 Ceiling Fan Thread Upper Part of Light Kit Lower i Part of Light Kit 10 Wires Terminal Block STEP 4 Fig 22 a Feed wires from the motor housing lower rim through the hole in the centre of the base plate b Attach the base plate to the motor STEP 5 Fig 23 a Feed wires through the thread of the upper part of
Download Pdf Manuals
Related Search
Related Contents
vaccination - Henry Schein m_1908_1908-1_v01.indd 1 2011.3.7 4:20:29 PM - BM Aroma ARC-1024E rice cooker revue HISTOIRE DE L`EDUCATION 取扱説明書 AOC 919Sz WBGT-ー ー 3は~ 労働環境での熱中症予防のためã SERIE KOSMOS Behringer EUROLIVE WB208 Quick Start Guide Copyright © All rights reserved.
Failed to retrieve file