Rotatub Users Manual V1 2_Archquip
Contents
1. ATUB wetpour mixer The Rotatub mixer range has been specially designed to significantly reduce the problem resin build up that most common wetpour mixers suffer from It is manufactured to the highest standards and constructed from selected quality materials The unique design will give many trouble free years of operation with only the minimum amount of maintenance when used in accordance with this User Manual www archquip com au 1 The Worlds 1 Wetpour Rubber Mixer reparation quipment OPERATION Outlet trap door handle Start Stop E sto j j Trap door guard wav READ AND FOLLOW THE MANUFACTURERS INSTRUCTIONS OF THE PRODUCTS TO BE MIXED 1 For best results add the rubber and glue products before starting the mixing blades 2 Press start and once the required consistency has been achieved place a suitable container wheelbarrow under the outlet trap door fig 1 The door height has been designed to fit a standard size wheelbarrow underneath 3 Keep the mixer running and open the outlet trap door The product will empty into the wheelbarrow and with the action of the spring loaded mixing blades the mixer will start to self clean 4 Once the product is discharged close the outlet trap door The mixing blades can now be stopped and the process restarted if required 2 www archquip com au 2 The Worlds 1 Wetpour Rubber Mixer reparation Rotatub T quipment CLEANING DM12 BOLT CQ CLAMPIN2. G PLATE MIXING SLEEVE MIXING BLADE DIN __ HPPE DISC Fig 2 0 ALWAYS DISCONNECT THE POWER SUPLY BEFORE CLEANING THE DRUM 0 READ AND FOLLOW SAFETY INSTRUCTIONS FROM THE MANUFACTURES OF THE PRODUCTS WHICH WERE MIXED TO REMOVE MIXING ASSEMBLY 1 Remove the M12 bolt and clamping plate from the mixing sleeve 2 Carefully lift the Gmixing sleeve upwards As each Q mixing blade exits the mixing bowl it will move away from the centre under the pressure of the spring 3 Remove the mixing blades and clean the bowl and blades as desired 4 Care must be taken not to damage the springs www archquip com au 3 The Worlds 1 Wetpour Rubber Mixer reparation quipment TO RE ASSEMBLE MIXING ASSEMBLY 1 Ensure all blade slots are clean and free from debris Grease mixer arms after every use 2 Check mixer arm springs are not bent or missing 3 Whilst mixing arm assembly is not fitted to the mixer install bottom scraper blade marked as number 1 to bottom mixer arm Ensure the numbering on the blade is upright and to the rear in relation to the rotational direction of the mixing arms 4 Install 2 3 and 4 if applicable numbered blades from bottom to top with the top blade being numbered 3 for Rotatub 25 or 4 for Rotatub 50 All numbers to the rear of the direction of the mixing rotation 5 Install the mixing arm assembly over the drive shaft and compress each blade as req
3. User Manual WETPOUR MIXERS The Worlds 1 Wetpour Rubber Mixer All P reparation Equipment www archquip com au T O7 3394 2724 F 3394 3207 E sales archquip com au reparation quipment INITIAL SETUP 1 Make sure the Rotatub mixer is up right with wheels and feet on the ground 2 If you have purchased a mixer with optional extras you need to set them up before use a Adjustable legs legs must be adjusted to suit the terrain the mixer will be operating on To do this you need to loosen the locking nuts use a hammer on the threaded shaft and adjust the feet up or down by rotating them until the mixer is as level as possible Once you are satisfied that the mixer is level tighten locking nuts for safety Step Locking Nuts Feet b Foldout Step the step is secured with zip ties from new for safe transportation Remove the zip tie securing step to mixer Take care not to remove zip ties holding crucial wiring to mixer Fold the step over and slide out on its rails Ensure the step is stable 3 When mixing base rubber eg 4 mesh buffings or 8 15mm granules replace the No 1 blade with the specially designed No 1 4 blade to allow for big particle clearance between the blade and the discharge hole in the floor 1 1 4 8 F www archquip com au 2 The Worlds 1 Wetpour Rubber Mixer reparation Rotatub quipment INTRODUCTION Congratulations on the purchase of your ROT
4. u A 19 SPECIFICATIONS Mixing Blades 3 83 A J JL2 4 www archquip com au The Worlds 1 Wetpour Rubber Mixer reparation quipment TRAINING COMPETANCY Archquip supports good workplace safety Copy this page and ensure each operator of the machine has read and understands how to correctly operate the machine Have you read this manual in full Y N Do you fully understand the instructions Y N If you answer no to any of these questions then do not operate the mixer fully understand the instructions and agree to operate the mixer in a safe manner Sign Date Print Name Archquip 50 Morley Street Coorparoo Qld 4151 T 07 3394 2724 F 07 3394 3207 E sales archquip com au www archquip com au 7 The Worlds 1 Wetpour Rubber Mixer
5. uired to enable the assembly to slide down to the floor of the mixer 6 Locate the drive shaft with the drive sockets on the bottom of the mixing arm assembly 7 Always start the mixer dry to test correct operation prior to adding rubber www archquip com au 4 The Worlds 1 Wetpour Rubber Mixer reparation Rotatub quipment PARTS 4 SLEEVE CLAMPING PLATE includes M12 Bolt TUB SAFETY GUARD MIXING SLEEVE 4 SPRING der DRIVE SHAFT 4 4 Ww i MIXING BLADE HDPE DISC See note below i UPPER TRAP DOOR SAFETY Nd GEARBOX 4 Adjustable legs MOTOR optional LOWER WHEEL Note 1 All mixing blades are imprinted with a number which corresponds to its position on the mixing sleeve No 1 being lowest on the sleeve when ordering spare blades you must supply the blade number 2 Always quote model and serial number when ordering spare parts www archquip com au The Worlds 1 Wetpour Rubber Mixer ll reparation Rotatub T quipment MAINTENANCE The Rotatub has been designed with minimum maintenance requirements to keep your mixer running at optimum performance simply follow these basic steps ee i i Leelee O m e eee eee 080 Per meme Qu rmt mim tme toto immer possesses Te ULE purpose light oil aa hii purpose light oil ew 0 mto emo er uu
Download Pdf Manuals
Related Search