User Manual and Installation Instructions
Contents
1. User Manual and Installation Instructions Model EA120BTSX Model EA120BIS Model EA90BTSX Model EA90BIS A WARNING For Outdoor use only Read the instructions carefully and be sure your barbecue is properly installed assembled and cared for Failure to follow these instructions may result in serious bodily injury and or property damage Please retain the manual for future reference These BBQs are configured for use with Propane Gas however are also approved for use with Natural Gas If you prefer to connect the BBQ to Natural Gas the BBQ needs to be configured for Natural Gas Converting this BBQ to Natural Gas must only be done by an authorized person and with a Natural Gas conversion kit supplied by Eurostyle Please contact Eurostyle to purchase a Natural Gas Conversion kit Remove any transit protection before using Please DO NOT use the two solid hot plates together NOTE TO INSTALLER TEST OPERATION OF THE APPLICANCE AND INSTRUCT THE USER BEFORE LEAVING Service amp Spare parts Your appliance should be serviced annually by a competent authorised person For serving or spare parts or Natural Gas conversion kit please contact Eurostyle Group trading as Euro Appliances Service line 08 81651012 Fax 08 8165 1018 Email admin eurostylegroup com au USE OUTDOORS ONLY This appliance shall only be used in an above ground open air situation with natural ventilation without s2. 1 Take out side burner grid 3 Assemble the side valve meanwhile put the knob seat on front panel and tighten the two screws together with knob seat and side valve f J VA 15 4 Put back side burner and tighten the screws meanwhile put the side burner inlet into side valve injector Make sure side burner inlet put into side valve injector 16 5 Connect the side burner ignitor Side Bumer ignitor Lead Electrode 6 Put back side burner grid 3 Attach left side table as shown in the diagrams below 1 Assemble the table and front panel with 3pcs of M6X10 and M6 M6X10 3PCS 2 Attach left side table On each side of the BBQ there are 2 preassembled screws Loosen them to 4mm of thread showing Hang the side table onto these loose screws on each side Assemble 3pcs of M6X15 screws in lower holes Tighten all screws 17 4 Fit flame diffusers as shown in diagram below 5 Fit cooking grids and plate as shown below NYNNE Please DO NOT use two hot plate together 6 Fit warming rack as shown below 7 Unscrew cap and place AA Battery into place with the end facing outwards Screw cap back on Upon pressing the ignition button you will hear a clicking noise if it has been installed correctly BATTERY AA battery is not provided 19 For Outdoor Built in BBQ EA120BIS amp EASOBIS 1 Assemble the side bracket 2 Fit flame diffuser
3. Accessible parts may be very hot keep young children away Close the valve of the gas cylinder or the regulator after use The use of this appliance in enclosed areas can be dangerous and is prohibited For storage and cylinder exchange disconnect the cylinder only Do not disconnect hose from the appliance Always maintain 915mm minimum clearance to combustible materials at the rear and sides of the BBQ Do not use this BBQ under overhead combustible surfaces Conversion to natural gas only to be done by authorized person The minimum cylinder size for use with this appliance is 7kgs The thread type of this appliance is G1 4B Exploded View EA120BTSX Model No N AN 9 W 1 Ill W i f A PH il H ST H T HA li f il il O A S Q NE S Exploded View EA120BIS Model No 8pcs M6x15 Exploded View EA90BTSX Model No 12 Exploded View EA90BIS Model No 8pcs M6x15 ASSEMBLY STEPS Tools required A CAUTION SHARP EDGES Wear gloves necessary 1 Attach left side table as shown in the diagrams below On each side of the BBQ there are 2 preassembled screws Loosen them to 4mm of thread showing Hang the side table onto these loose screws on each side Assemble 3pcs of M6X15 screws in 2 lower holes Tighten all screws 14 2 Connect side burner
4. Using 2 sets of bolts nuts and washers provided attach the bracket to the right side of the grill as shown in Fig 1 by passing two bolts through the bracket and then the outside of your grill Place a washer on the end of each bolt Secure bolts with nuts Take care not to over tighten the bolts Repeat for right side Slide rotisseries Motor over right side Bracket Fig 2 3 Place the collar Spit Rod collar and meat prongs onto the rotisserie rod and attach it to the support on the right hand side of the rotisserie bracket on the grill The rod should turn smoothly Fig 4 4 Place washer onto the rotisserie rod followed by the weight balance Then attach the handle into the rotisserie rod The weight balance should be positioned in the space between the washer and handle of the rod Fig 5 6 6 Place the end of the rotisserie rod into the motor Make sure rotisseries rod is aligned properly with the motor Fig 7 Using the Rotisserie burner Plug the unit into an electrical outlet Slide one of the meat prongs onto the rod prongs toward the food Center the food to be cooked on the rod followed the thumbscrews It may also be necessary to wrap food with butcher s string never use nylon or plastic string to secure loose portions Once the food is secure insert the pointed end of the rotisserie rod into the motor assembly and rest the other end on the support on the right hand side of the grill If needed remove the cookin
5. A120BIS Opening required in base for gas inlet connection Ventilation required on both sides 260cm Min 26cm x 10cm Opening Door to access gas connection point NOTE Additional unobstructed openings no less than the size of the ventilation openings should be added to the cabinet to allow air through 23 Clearances Allow adequate clearance on the right and left side of the BBQ so that the rotisserie motor and skewer where supplied can be removed Ensure there is at least 100mm clearance at the rear so that the hood can be opened without obstruction Allow a minimum clearance of 10mm from the sides and rear of the BBQ to any non combustible construction located below the BBQ cooking surface Any combustible materials must be at least 915mm away from the sides and rear of the BBQ Do not use the BBQ under overhead combustible surfaces Do not obstruct the ventilation air openings around the structure 24 For rotisseries kit A WARNING The side burner is not allowed to operate during operation of turnspit motors Rotisseries Motor AC Motor DC 1 Bolt and Nut Motor Bracket Spit Rod collar 4 Sprong Meat Fork Spit Rod Collar Weight Balance Counterweight Handle Washer Quantity SE BEER D Spit Rod collar 1 G Collar x1 I Handle x1 ee B Bolt and Nutx2 25 ASSEMBLY INSTALLATION AND OPERATION INSTRUCTIONS Assembling and Attaching Rotisseries Kit to barbecue 1
6. ched to the BBQ for use should be stored outdoors and well away from this appliance Important e When disconnecting and removing the gas cylinder for the purpose of refilling always observe the following procedure e Ensure that all gas control valves on the appliance and the gas cylinder are turned off before disconnecting the regulator from the cylinder e Do not smoke or use a naked flame near the appliance or gas cylinder while disconnecting the gas line between the appliance and gas cylinder e Remove the gas cylinder from the enclosure before disconnecting the regulator from the appliance e Tighten all connections before placing the gas cylinder back in its enclosure e The gas leak testing procedure should be conducted every time the gas cylinder is refilled and reconnected to the appliance before using the appliance Regulator Connection 1 Check that all control knobs are in the Off position 2 Make sure the cylinder valve is off 3 Remove the protective cap from the cylinder if present 4 Leak test the connection with a soapy water solution Gas Leak Test Procedure Never use a naked flame to check for gas leaks Always use the following procedure to check for gas leaks In a small container mix up a solution of water and detergent or soap Mix the solution well Make sure that the gas supply valve on the gas cylinder is turned on Make sure that the gas control valves on the appliance are all turned off Bubbling of the solution
7. e at least 25 of total wall area 30 percent or more in total of the remaining wall area is open and MA IN unrestricted WARNING DO Use spanner to tighten all gas fittings Check all gas hose and line connection for damage cuts or cracks each time for using the appliance Always leak test with soapy water Check main burners side burners and infrared rear burner regularly for spider webs and insect nests as these may interfere with the proper operation of the burners and must be removed before using the burners Use the appliance outdoors only Accessible parts maybe very hot Always Keep children away from the appliance Have the gas cylinder filled by an authorized gas supplier Always wear protective gloves when handling hot component Close the gas cylinder valve after each use Clean the grease tray regularly USE grill at combustible wall or surface least 915mm from any Burning off the barbecue after every use for approx 15 minutes will keep excessive food residue to a minimum Turn off the gas supply at the cylinder in the event of gas leak Do not do Do not lean over appliance when lighting Do not store combustible materials gasoline flammable liquids or vapors within vicinity of barbecue Do not use appliance with any cover on Do not use plastic or glass utensils on the Barbecue Do not use the appliance in strong winds Do
8. g grates for more room Turn the power switch to the ON Position to start the rotisserie motor Turn the power switch off after cooking Notes When using the rotisserie burner make sure all main burners are off When using the rotisserie burner it is not recommended to use Side burners as injury may result from burning CARE AND MAINTENANCE Turn off unplug and remove the rotisserie kits when not in use After using clean all metal parts using a dry cloth to avoid rusting Do not immerse any parts in water Store in a dry place TROUBLESHOOTING If the rod is not rotating at a constant speed reposition the meat on the forks and rod to adjust the weight so that it is balanced 26
9. heard After the infrared rear burner is lit keep pushing down the control knob and hold for 5 seconds It may take a little while for the gas to flow to the infrared burner because it is some distance away from the gas valve For Match Lighting 1 Follow above instruction step 1 3 2 For Main burner place the match into match lighting stick and light the match then put into lighting hole on right side of the barbecue For burners far away from right side of the barbecue take the cooking grate out and place the match near the main burner ports i For side burner place the lit match on the holes of the 7 SS ae SL side burner head i ee HENS For infrared rear burner place the lit match on the surface of ceramic panels 3 Push down and turn the knob anticlockwise to HIGH Ay position Thus the burner could be lit If the burner does not light turn off the gas tap and wait for 5 minutes then repeat this step 2 3 Before cooking for the first time operate the barbecue for about 15 minutes with the lid closed and the gas turned on HIGH A This will heat clean the internal parts and dissipate odor from the painted finish The color of cooking area may slightly discolour This is normal and it is the nature of material A WARNING While igniting main burner and infrared rear burner please make sure the lid for main burner is in open position While igniting side burner please make sure the lid fo
10. not dismantle control valves Do not test for gas leaks with a naked flame Do not store spare gas cylinders in the cabinet Do not lay the gas cylinder down always keep upright Do not use appliance indoors Do not modify the construction of the appliance or the size of any burner injector orifice or any other components Do not move the appliance during use Do not obstruct any ventilation of the appliance Do not allow the flexible gas supply hose or any electrical cord to come in contact with any heated surface of the appliance Do not use charcoal or any other solid fuel in this appliance Do not disconnect any gas fittings while the appliance is in use Do not use a rusty or dented gas cylinder with a damaged gas valve Do not fill the gas cylinder beyond 80 Capacity Do not use the infrared rear burner at the same time as other burners Gas Cylinder Information Gas Cylinder Safety Information e This appliance is designed to be used with a gas cylinder not exceeding 9KG e The gas cylinder supply valve must be turned off when the appliance is not in use e Gas cylinders must be stored outdoors out of reach of children and must not be stored in a building garage or any other enclosed area e The gas cylinder used must incorporate a safety collar to protect the valve assembly Never store a spare cylinder under the barbecue shelves or inside the trolley housing Any LPG cylinder not atta
11. r side burner is in open position Battery Replacement Unscrew the battery cap and plastic nut on the igniter at the front of the control panel Replace the battery and refit the cap CLEANING AND CARE A WARNING All cleaning and maintenance should be carried out when the barbecue is cool and with the fuel supply turned OFF at the gas cylinder DO NOT mistake brown or black accumulation of grease and smoke for paint Surfaces of the gas grills amp hotplates are not painted Apply a strong solution of detergent and water or use a grill cleaner with scrubbing brush on insides of grill lid and bottom Rinse and allow to completely air dry DO NOT apply a caustic grill oven cleaner to any painted surfaces DO NOT use abrasive or flammable cleaners as it will damage the parts of the product and may start a fire Plastic parts wash with warm soapy water and wipe dry Porcelain surfaces because of glass like composition most residue can be wiped away with backing soda water solution or specially formulated cleaner Use nonabrasive sourcing powder for stubborn stains Painted surfaces wash with mild detergent or nonabrasive cleaner and warm soapy water Wipe dry with a soft nonabrasive cloth Stainless steel surfaces Stainless steel will surface rust if not maintained well To maintain your grill s high quality appearance wash with mild detergent and warm soapy water and wipe dry with a soft nonabrasive cloth after each
12. s as shown in diagram below 20 3 Fit cooking grids and plate as shown below ENTON Please DO NOT use two hot plate together Barbecue Dimensions for inbuilt models EA9OBIS EA120BIS Guide for building in Warning Contact your local municipality for any building codes regulating the installation of outdoor barbecue appliances Outdoor installations must conform to local codes or in the absence of local codes with AS5601 Gas Installations THE CONSTRUCTION OF THE ENCLOSURE AND INSTALLATION OF THE BBQ SHOULD BE CARRIED OUT ONLY BY AUTHORISED PERSONS The BBQ must be placed on a construction made from non combustible materials which must support the full weight of the BBQ For Propane installations the BBQ must be separated from the LPG cylinder and there must be enough room so that the cylinder can stand upright THE BARBECUE MUST ALSO BE SECURED TO THE ENCLOSURE TO PREVENT IT BEING PULLED OUT AND STRAINING THE GAS CONNECTIONS Ventilation Ventilation must be in accordance with AS5601 Gas Installations In general the appliance should have adequate ventilation for complete combustion of gas proper flueing and to maintain temperatures of immediate surroundings within safe limits The air that the BBQ requires for proper combustion enters through both sides of the BBQ The construction of the enclosure must provide an unobstructed air supply via a minimum of 260cm2 on both sides 825mm Min EA90BIS 1125mm Min E
13. tagnant areas where gas leakage and products of combustion are rapidly dispersed by wind and natural convection Any outdoor enclosure or alfresco area in which the appliance is used shall comply with one of the following An enclosure with walls on all sides but at least one permanent opening at ground level and no overhead cover See Figure 1 1 Within a partial enclosure that includes an overhead cover and no more than two walls See Figure 2 amp 3 1 Within a partial enclosure that includes an overhead cover and more than two walls the following shall apply At least 25 of the total wall area is completely open and At least 30 of the remaining wall area is open and unrestricted See Figure 4 amp 5 1 Inthe case of balconies at least 20 of the total of the side back and front wall areas shall be and remain open and unrestricted The following diagrams provide a diagrammatic representation of outdoor areas Rectangular areas have been used in these figures the same principles apply to any other shaped area BU me Figure 1 Enclosure with walls on all sides but Figure 2 Partial Enclosure with overhead cover and VAN Figure 4 Open side at least 25 of total wall area no overhead cover vg Figure 3 Partial Enclosure with overhead cover and no more than two walls DK 7 no more than two walls 30 or more in total of the remaining wall area is open and unrestricted Figure 5 Open sid
14. the side burner with the lid in the closed position DO NOT attempt to light burner with lid closed A build up of non ignited gas inside a closed grill is hazardous The side burner is designed for pot pan with diameter 60 260mm Side burner lid can not be used as work table do not put anything on the side burner lid Lighting Instruction 1 Read instructions before lighting 2 Open the lid and make sure all the knobs are on the OFF position 3 Connect the regulator to gas cylinder and the hose to barbecue Turn the gas supply ON at the cylinder Check with the use of soapy water for any gas leakage between the bottle and the regulator 4 Push down the control knob and keep pressing whilst turning anti clockwise to HIGH position whilst also pressing the ignition button a clicking sound is heard this will light the burner 5 If the burner still does not light turn the control knob to OFF O wait 5 minutes and repeat step 4 If the burners do not stay alight repeat steps 4 and 5 6 Adjust the heat by turning the knob to the High By ow A position 7 To turn the barbecue OFF turn the cylinder valve to the OFF position and then turn all of the control knobs on the appliance clockwise to the OFF position For Infrared rear burner Push down the control knob and keep pressing whilst turning anti clockwise to HIGH To position and also pressing the ignition button a clicking sound is
15. use Use stainless steel protection liquid like WD 40 on the surface to avoid rust Cooking grid Use a mild soapy water solution Non abrasive scourer can be used on stubborn stains then rinse with water Abnormal Operation Any of the following are considered to be abnormal operation and may require service Yellow tipping of the yellow flame Sooting up of grills plates Burners not igniting properly Burners failing to remain alight Burner extinguished by trolley doors Gas valves which are difficult to turn Technical Information Model No EA120BTSX cB6 sBG001 BU Total Nominal 96 1 MJ h Gas Consumption Main Burners 11 6 MJ h x 6 Nominal gas consumption Side Burner 15MJ h Back Burner 11 5MJ h Injector Size Main Burners 0 98mm Side Burner 1 13mm Back Burner 1 00mm EA120BIS cB6 86001 B 2 7 5 KPA 81 1 MJ h Propane Main Burners 11 6 MJ h x 6 Back Burner 11 5MJ h Main Burners 0 98mm Back Burner 1 00mm Model No EA90BTSX cB4 5B6001 BU Total Nominal 72 9 MJ h Gas Consumption Main Burners 11 6 MJ h x 4 Nominal gas consumption Side Burner 15MJ h Back Burner 11 5MJ h Injector Size Main Burners 0 98mm Side Burner 1 13mm Back Burner 1 00mm EA9OBIS cB4 BG001 B 2 75KPA 57 9MJ h Propane Main Burners 11 6 MJ h x 4 Back Burner 11 5MJ h Main Burners 0 98mm Back Burner 1 00mm AGA Approval No AGA 7142 G For Use outdoors and in well ventilated areas Warning
16. will indicate that there is a leak present 1 2 3 4 Using a brush or spray bottle apply the solution to the gas line and each join in the gas line 5 6 Re tighten or re seal any joints that are leaking 7 If a leak persists then contact your distributor or the manufacturer for assistance AUS Standard POL Regulator Po Shutoff Valve Spanner wrench Tighten in this direction Bleeder valve screw ra Regulator and hose DI A A Protector cap LIGHTING YOUR BARBECUE A WARNING This barbecue is designed for use outdoors keep away from any flammable materials It is important that there are no overhead obstructions and that there is a minimum distance of 915mm from the side or rear of the appliance Do not use the BBQ under overhead combustible materials It is important that the ventilation openings of the cylinder compartment are not obstructed The barbecue must be used on a level stable non flammable surface The appliance should be protected from direct draughts and shall be positioned or protected against direct penetration by any trickling water e g rain Parts sealed by the manufacturer or his agent must not be altered by the user No modifications should be made to any part of this barbecue and repairs and maintenance should only be carried out by an authorized person DO NOT let children operate or play near grill DO NOT use charcoal or ceramic briquets in a gas grill DO NOT light or use
Download Pdf Manuals
Related Search