TSP 400 Installation Manual
Contents
1. HSITON3 Two ferrite core noise filters large and small come packed with the printer The small noise filter is for the RS232C serial interface cable while the larger one is for the cable of peripheral units Product Product Code 09990728 Code 09990723 Model Ferrite Core Model Ferrite Core 024mm Name _ TFc 20 10 10 928mm Name TFC 23 11 14 For Interface Cable For Peripheral Unit Cable The ferrite cores are packed so they are open as shown in Fig 3 2 If you find that a ferrite core 1s not open use apointed object to pry the plastic lock of the ferrite core apart Fig 3 1 When you do take care not to damage the ferrite core or the plastic lock Small ferrite Core 24mm diameter Interface Fig 3 3 Cable Fig 3 2 Pass fastener around cable and lock it Cut off excess with scissors Fig 3 4 29 Installation of the interface cable ferrite core Clamp the small ferrite core onto the interface cable as shown in Fig 3 2 Take care to avoid damaging the interface cable when installing the ferrite core The ferrite core should be anchored firmly in place with the fastener that comes with it as shown in Fig 3 3 and 3 4 DE o Z LU Installation of the peripheral unit cable ferrite core E Clamp the large ferrite core onto the cable of the interface unit using the same procedure as you do forthe interface cable ferrite core With the pe2. Request To Send The printer sets this signal to SPACE when it is ready to send The host sets this signal to SPACE when it is ready to send NOTE The printer does not monitor this signal Not used Signal ground Not used Not used The printer sets this signal to SPACE when it is ready to receive This pin outputs the same signal as pin 20 to which it is con nected Not used Signal ground The printer sets this signal to MARK to indicate an error condition machine error no paper etc Multi Printer TXD Diode gate TXD Multi Printer DTR Diode gate DTR N C Not used DTR Data Terminal Ready The printer sets this signal to SPACE when it is ready to re ceive Not used Not used 29 RS 422A Interface Signal name Direction Function SD OUT These pins carry data from the printer These pins carry data to the printer The host sets this signal to SPACE when it is ready to send NOTE The printer does not monitor this signal The host sets this signal to SPACE when it 1s ready to receive NOTE The printer does not monitor this signal The printer sets this signal to SPACE when it is ready to receive Interface Connections The printer sets this signal to SPACE when 1t is ready to receive Refer to the host computer
3. s interface specifications for details of how to connect the interface The following illustrations show typical connection configura tions RS 232C S GND FAULT DTR Printer side IBM PC side F GND TXD RXD RTS CTS DSR S GND DCD DTR 30 X a Z Lu o lt RS 422A Printer n Printer side ON 17 Twisted pair cable Host side i RD 1 90 SD NI 10 4 DW oo OQ OOOO 7 I LS 18 Printer n 1 RD lt 3 104 4 XIGNAddV gt Connectors and Signal Names Parallel Interface Conforms to Amphenol connector 57 30360 36 Printer Side 19 Signal Name Sample Circuit DATA 1 74LS equivalent DATA 8 gt gt 74LS equivalent STROBE 1000 1000pF x O Z o o lt 74LS equivalent 3 XIGNAddV Signal name Direction Function STROBE IN Strobe pulse for dataread Usually HIGH goes LOW to trigger data read DATA 1 8 IN Parallel data lines for eight bitdata HIGH is 1 LOW is 0 ACK Printer outputs this pulse for approxi mately Jus to indicate that data read is completed Printer becomes ready to receive new data at the moment the ACK pulse ends DC level signal indicating printer s current status
4. Couper l alimentation l impri mante et l ordinateur RE 2 Ins rer le c ble d interface dans le connecteur S assurer que le c ble A est orient correctement avant de BN l ins rer 3 Fermer les attaches du connecteur 4 Relier l autre extr mit du c ble Fig 4 2 Di SEXES d interface l ordinateur INHALTSVERZEICHNIS 1 AUSPACKEN UND KONTROLLE cen 13 1 1 Auspacken teen i T 13 1 2 Hinweise een ia 13 2 FUNKTION UND BEZEICHNUNG DER EINZELNEN BAUTEILE 14 3 INSTALLATION DER FERRITKERNE NUR EUROPA 15 Installation des Ferritkerns f r das Schnittstellenkabel 16 Installation des Ferritkerns f r das Peripheriegeratekabel 16 4 ANSCHLUSS DES SCHNITTSTELLENKABELS 17 4 1 Serielle Schnittstellen RS 232C oder RS 422A 17 4 2 Parallele Centronics Schnittstelle 17 ANHANG esse E ee see 24 Der Anhang erscheint nur im englischen Teil dieser Bedienungsanleitung HOSLNAG 1 AUSPACKEN UND KONTROLLE 1 1 Auspacken Uberpriifen Sie an Hand von Abbildung 1 die Teile in der Verpackung und stellen Sie sicher daB alle n tigen Positionen geliefert wurden es sollten f nf sein Falls eines der Teile fehlen sollte wenden Sie sich bitte an Ihren H ndler Papierrolle Achse f r die Papierrolle 6
5. TIT 5 24mm Q28mm Ferritkern f r das Ferritkern f r Schnittstellenkabel Peripheriege nur EU r tekabel nur EU Bedienungsanleitung i Drucker Aufstellanleitung Kabelbinder nur EU Abb 1 1 l 2 Hinweise Wahlen Sie f r die Aufstellung Ihres Druckers zun chst einen geeigneten Platz aus Er sollte folgende Merkmale aufweisen e Er sollte nahe einer leicht zug nglichen Netzsteckdose sein e Er sollte eine stabile ebene und ersch tterungsfreie Oberfl che haben e Er sollte nicht berm iger Hitze ausgesetzt sein wie direktem Sonnenlicht einer Heizung usw e In der Druckerumgebung sollte keine berm ige Luftfeuchtigkeit herrschen e Sie sollte nicht berm ig staubig sein e Die Stromversorgung sollte stabil und nicht anf llig f r St rungen sein Sie sollten den Drucker zum Beispiel nicht an einem Stromkreis zusammen mit groBen eventuell St rungen verursachenden Ger ten wie K hlschrank oder Klimaanlage betreiben HINWEIS Stellen Sie sicher daf die Spannung Ihres Stromnetzes der Betriebs spannung entspricht die auf dem Typenschild des Druckers ange geben ist 13 2 FUNKTION UND BEZEICHNUNG DER EINZELNEN BAUTEILE Machen Sie sich in Abbildung 2 1 mit den Bestandteilen des Druckers und seinen Funktionen vertraut Druckerklappe Bedienfeld Automatischer Sie sch tzt den Druckkopf und Es zeigt den Druckerstatus an und Papierschneider andere Bauteile im Inneres Ihr
6. la stampante devono essere rese compatibili attraverso le impostazioni degli interrut tori DIP della stampante vedere l APPENDICE 4 2 Interfaccia parallela tipo Centronics CD Spegnere sia la stampante che il computer 2 Inserire il cavo d interfaccia nel a connettore assicurarsi che il cavo A sia orientato nel senso corretto pri ma di inserirlo B Bloccare i fermagli del connettore Collegare l altra estremit del cavo Fig 4 2 d interfaccia al computer 23 APPENDIX DIP SWITCHES DIP switches are located on the interface board The number of switches varies according to the board as follows Centronics No DIP switches RS 232C One 8 bit DIP switch RS 422A 8 bit DIP switch and one 4 bit DIP switch 00000000 x m o o lt 24 XIGNAddV DIP switch settings a DIP switch 1 RS 232C RS 422A Switch Setting Baud Baud Handshaking DTR X ON X OFF Data bits 8 bits 7 bits Parity type Not used Used Parity type Odd Even DCI DC3 Invalid Valid RS 232C only When turning power ON Refer to the table below Baud 2400BPS 4800BPS 9600BPS 19200BPS Factory settings ALL ON When the printer s power is ON DC1 DC3 valid mode Select Deselect Adressable mode Deselect Select RS 422A only DC1 DC3 invalid mode Select Select b DIP switch 2 RS 422A only DIP SW 2 RS 422A only DC1 DC3 Addressable
7. mode 2 DC1 DC3 invalid mode 2 3 4 5 6 8 10 valid mode ON ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF OFF ON OFF ON ON ON OFF OFF OFF OFF ON OFF ON ON OFF 25 Print Density Adjustment Since the sensitivity of different types of heat sensitive paper varies you can adjust the print density by varying the current supplied to the thermal head Variable resistor used to adjust the print density The print density can be adjusted using the variable resistor inside the hole beside the interface connector on the back of the printer x a Z o lt 1 adjust the density turn the resistor roughly two times using small cross head screwdriver 2 Turn the resistor to the right clockwise for a darker print density or to the left counterclockwise for a lighter density NOTE If the density is increased to a higher level than necessary when printing on highly sensitive heat sensitive paper the dots may be too large and the print quality may decrease Excessively high energy adjustment may reduce head life 26 XIGNAddV Sensor Adjustment Sensor levels are adjusted at the factory If necessary you can readjust the levels as described below 1 Remove the ROM cover located beneath the paper roll holding area 2 Hold down the FEED and ON LINE switches while switching on the power and continue to hol
8. CAVO D INTERFACCIA 23 4 1 Interfaccia seriale RS 232C o RS 422A 23 4 2 Interfaccia parallela tipo Centronics eee 23 ADPENDIGCE i sana e E SE DU oe Gi aic ini 24 L Appendice appare solo nella sezione in inglese di questo manuale zi gt gt 2 1 APERTURA CONTROLLO DELLA CONFEZIONE 1 1 Apertura della confezione Confrontare il contenuto della confezione con i componenti mostrati nella Figura 1 1 per controllare di aver ricevuto tutto nella scatola dovrebbero esserci cinque componenti Nel caso mancasse qualcuna di queste parti contattare il fornitore presso cui si e effettuato l acquisto Rotolo di carta campione Asta del P rotolo di carta 24mm 28mm Anello di ferrite Anello di ferrite per cavo per cavo unita d interfaccia periferica solo solo Europa Europa Manuale di istruzioni Stampante Manuale di installazione Fascetta di fissaggio solo Europa Fig 1 1 1 2 Avvertenze Prima dell installazione della stampante assicurarsi di disporre di un luogo adatto in cui collocarla Per luogo adatto intendiamo un luogo e vicino ad una presa elettrica facilmente accessibile e su una superficie solida e piana che non subisca vibrazioni e lontano da fonti di calore eccessivo come luce diretta del sole apparecchi di riscaldamento ecc e lontano da umidit eccessiva e lontano da
9. E UNIQUEMENT 9 Installation du tore de ferrite de c ble d interface 10 Installation du tore de ferrite de c ble de p riph rique 10 4 RACCORDEMENT DU CABLE D INTERFACE 11 4 1 Interface s rie RS 232C ou RS 422A sene 11 4 2 Interface parall le type Centronics ii 11 APPENDICE alain pta 24 L appendice n est pas traduit 1 DEBALLAGE ET INSPECTION 1 1 D ballage V rifier chaque pi ce de la bo te en se r f rant la Figure 1 afin des assurer qu on a bien tout re u il doit y avoir cinq pi ces En cas d absence d une de ces pi ces contacter le fournisseur sed Rouleau de papier chantillon de papier SIVONVH4 24mm 28mm Tore de ferrite de Tore de ferrite c ble d interface de c ble de Europe p riph rique uniquement Europe uniquement Manuel d utilisation Imprimante Manuel d installation Attache Europe uniquement Fig 1 1 1 2 Remarques sur la manipulation Avant de commencer l installation de l imprimante s assurer qu on dispose bien d un endroit appropri pour la mettre Un endroit appropri doit satisfaire aux conditions suivantes e A proximit d une prise d acc s facile e Surface ferme et niveau pratiquement sans aucunes vibrations A distance de toute chaleur excessive par exemple lumi re du soleil directe radiateurs etc A
10. LOW indicates that printer is ready to receive the next data HIGH indicates that printer is unable to receive The printer holds this signal HIGH during any of the follow ing conditions CD While data entry is in progress 2 While printer is offline While error condition exists PAPER OUT DC level signal indicating whether printer has paper The signal stays LOW while paper is present it goes HIGH to indicate that paper has run out SELECTED DC level signal stays HIGH while printer is online N C Not used SIGNAL GND CHASSIS GND Signal ground Printer frame ground 5V Outputs 5V Max 50mA TWISTED PAIR RETURN Return pins for various signals Each pin is connected to the corresponding signal line by twisted pair line RESET LOW level causes printer to reset its control circuitry and return to its initial state ERROR EXT GND Goes LOW to indicate that printer is unable to print Ground terminal for external connection N C Not used Fixed HIGH at printer side 33 Peripheral Unit Drive Circuit A drive circuit for driving peripheral units such as cash drawers is featured on the main logic board of this printer A modular connector for driving peripheral units is featured on the output side on the drive circuit When using this circuit connect the cable for the peripheral unit Cables must be prepared by the user Note t
11. THERMAL PRINTER TSP400 INSTALLATION MANUAL GUIDE D INSTALLATION AUFSTELLANLEITUNG MANUALE DI INSTALLAZIONE Sit TABLE OF CONTENTS 1 UNPACKING AND INSPECTION 1 J l Unpacking ee ent eter rere eee reete 1 1 2 Handling Notes inscrit ie 1 2 PARTS IDENTIFICATION AND NOMENCLATURE 2 3 FERRITE CORE INSTALLATION EUROPE ONLY 3 Installation of the interface cable ferrite core 4 Installation of the peripheral unit cable ferrite Core 4 4 CONNECTING THE INTERFACE CABLE ene 5 4 1 RS 232C or RS 422A Serial interface sees 5 4 2 Centronics type Parallel interface sess 5 APPENDIX serres 24 1 UNPACKING AND INSPECTION 1 1 Unpacking Check each item in the box against Figure 1 1 to make sure that you have everything there should be five items If any of these items are missing contact your supplier m Z C 60 BE Sample paper roll Paper roll shaft 24mm 28mm Ferrite core for Ferrite core interface cable for peripheral E U only unit cable E U only User s manual Printer Installation Manual fastener E U only Fig 1 1 1 2 Handling Notes Before you start setting up your printer make sure that you have a suitable place in which to locate it By a s
12. atings for diodes DI and D2 at Ta 25 C Average rectified current lo 1A Maximum forward surge current 60Hz 1 cycle sine wave Irsm 40A 5 Absolute maximum rating for transistors TRI and TR2 at Ta 25 C Collector current Ic 2A XIGNAddV A 35 1996 1 Sit HEAD OFFICE STAR MICRONICS CO LTD 20 10 Nakayoshida Shizuoka 422 Japan Tel 054 263 1115 Telefax 054 263 8714 OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA INC 70 D Ethel Road West Piscataway NJ 08854 U S A Tel 908 572 9512 Telefax 908 572 5095 Telex 299766 STAR UR STAR MICRONICS DEUTSCHLAND GMBH WesterbachstraBe 59 D 60489 Frankfurt Main 90 Germany Tel 0697 89990 Telefax 0697 81006 Telex 417 5825 STAR D STAR MICRONICS U K LTD Star House Peregrine Business Park Gomm Road High Wycombe Bucks HP13 7DL UK Tel 01494 471111 Telefax 0494 473333 Printed in Japan 80871025
13. biliser le tore de ferrite au moyen de l attache fournie comme indiqu la Fig 3 3 et la Fig 3 4 Installation du tore de ferrite de c ble de p riph rique Serrer le grand tore de ferrite au c ble d interface en suivant m me proc dure que celle du tore de ferrite du c ble d interface Dans le cas du tore de ferrite du c ble de p riph rique il faut toutefois faire une boucle avec le c ble de la mani re indiqu e la Fig 3 5 lt Z L or LL NS cm ou moins Grand tore de ferrite diam tre 28 mm Fil la terre Une seule boucle Fig 3 5 10 4 Raccordement du cable d interface 4 1 Interface s rie RS 232C ou RS 422A Suivre les proc dures indiqu es ci dessous pour relier le c ble d interface Couper l alimentation l impri mante et l ordinateur 2 Ins rer le c ble d interface dans le connecteur S assurer que le c ble est orient correctement avant de l ins rer SIVONVH4 C ble d interface I Serrer les vis droite et gauche pour les immobiliser sur le connecteur Relier l autre extr mit du c ble d interface l ordinateur Fig 4 1 REMARQUE Rendre compatibles les conditions de transfert de donn es entre l ordinateur et l imprimante en r glant les microrupteurs de x l imprimante en cons quence Se r f rer 4 2 Interface parall le type Centronics CD
14. d them down until you hear a triple beep This will take about five seconds When you hear the triple beep release the buttons to enter sensor adjustment mode a Reflective Sensor e Insert a non black area of paper into the mechanism s sensor area e Rotate the main PCB s sensor adjustment knob VR4 to the point where the HEAD UP indicator comes on b Paper Out Sensor e Insert a non black area of paper into the mechanism s sensor area e Rotate the main PCB s sensor adjustment knob VR3 to the point where the NO PAPER indicator comes on c Transmissive Sensor e Insert the backing portion of a label sheet into the mechanism s transmissive sensor area Insert the backing part only not the label itself e Adjust the main PCB s coarse VR1 and fine VR2 adjustment knobs to the point where the ERROR indicator comes on NOTE When inserting paper be sure to lower the head so that it is close to its normal fixed position 97 VRI VR3 Main PCB Interface PCB Variable Resistances Sensor Adjustment Knobs x O o o lt 28 XIGNAddV Connectors and Signal Names Serial Interface RS 232C Interface Signal name BO O O O O O O O 530 O O O O O O O O O O O14 Direction Function F GND Frame ground Outgoing data Incoming data
15. distance de toute humidit excessive e A distance de poussi re excessive Acc s une source d alimentation constante ne subissant pas de pointes d alimentation Ainsi par exemple il ne faut pas relier l imprimante au m me circuit qu un appareil important bruyant du genre r frig rateur ou climatiseur REMARQUE S assurerque latension de ligne correspond latension indiqu e sur la plaque signal tique de l imprimante E 2 IDENTIFICATION DES PIECES ET NOMENCLATURE Se r f rer la Figure 2 1 pour se familiariser avec les composants et capacit s de l imprimante Couvercle d imprimante Tableau de commande Couteau de papier Prot ge la t te d impression ainsi Indique l tat de l imprimante et automatique que d autres composants internes simplifie les fonctions de pilotage par commande de l imprimante commande de l imprimante tout en facilitant leur ex cution e L Z L or LL TSP442 TSP412 Barre de d clenchement Ouvre et ferme la t te d impression qui retient le papier contre le cylindre Connecteur d entra nement de p riph rique Connexion uniquement des p riph riques du genre caisses enregistreuses etc Interrupteur d alimentation Connecte ou coupe l alimentation Couvercle du connecteur Connecteur d interface Relie l ordinateur l imprimante Fig 2 1 3 INSTALLATION DU TORE DE FERRITE EUROPE UNIQUEMENT REMARQUE Prend
16. ecker Kabel Abb 3 2 Produkt 9990723 nummer Ferritkern 28mm Modell Mc 3311 14 f r das Peripherieger tekabel F hren Sie den Kabelbinder durch die se am Ferritkern Abb 3 3 Straffziehen und abschneiden F hren Sie den Kabelbinder um das Kabel und ziehen Sie ihn fest Schnei den Sie das berstehende Ende mit einer Schere ab Abb 3 4 15 Installation des Ferritkerns f r das Schnittstellenkabel Klemmen Sie den kleinen Ferritkern auf das Schnittstellenkabel siehe Abbil dung 3 2 Achten Sie darauf da bei der Installation des Ferritkerns das Kabel nicht besch digt wird Der Ferritkern sollte mit dem mitgelieferten Kabelbinder sicher an seinem Platz befestigt werden Siehe Abbildungen 3 3 und 3 4 Installation des Ferritkerns f r das Peripherieger tekabel Klemmen Sie den gro en Ferritkern auf das Kabel f r die Peripherieger te Gehen Sie dabei genauso vor wie oben beim Schnittstellenkabel beschrieben Beidiesem Ferritkern allerdings m ssen Sie das Kabelin einer Schlaufe laufen lassen wie in Abbildung 3 5 gezeigt an 0 F LU a M cm oder weniger groBer Ferritkern 28 mm Durchmesser Massekabel eine Schlaufe Abb 3 5 16 4 ANSCHLUSS DES SCHNITTSTELLENKABELS 4 1 Serielle Schnittstellen RS 232C oder RS 422A Gehen Sie zum Anschluf des Schnittstellenkabels vor wie unten beschrieben CD Schalten Sie Drucker und Com
17. es mit ihm lassen sich die befehlsgesteuert Druckers Druckerfunktionen bequem und einfach steuern an O 0 F LLI a TSP442 TSP412 Entriegelungshebel Mit ihm wird die Druckkopfeinheit entlastet und angepre t mit der das Papier an die Walze gedr ckt wird Buchse f r Peripherieger te Sie dient zum Anschlu von Netzschalter Peripherieger ten wie etwa Geldladen Mit ihm wird das Ger t an und etc ausgeschaltet Abdeckung f r die Schnittstellenbuchse Schnittstellenbuchse An ihr wird der Computer an den Drucker angeschlossen Abb 2 1 Id HOS1A30 3 INSTALLATION DER FERRITKERNE NUR EUROPA HINWEIS Beachten Sie die folgenden Schritte besonders sorgf ltig Zwei Ferritkerne zum Filtern von St rungen ein gro er und ein kleiner werden mit dem Drucker geliefert Der kleine Entst rungsfilter findet am Kabel f r die serielle RS232C Schnittstelle Verwendung das grobe am Kabel f r Peripherieger te Produkt 0090778 nummer Ferritkern 024mm Modell rco 20 10 10 f r das Schnittstellenkabel Die Ferritkerne werden in der offenen Stellung geliefert siehe Abbildung 3 2 Sollte ein Ferritkern nicht offen sein Offnen Sie den Plastikverschluf des Ferritkerns mit einem spitzen Ge genstand Abbildung 3 1 Achten Sie dabei darauf da Sie weder Ferritkern noch Plastikverschlu besch digen kleiner Ferritkern 24 mm Durchmesser St
18. hat Page Mode does not support external device drive commands Drive commands are available only in Line Mode Use cables which meet the following specifications 1 Use the modular plug as shown in Figure 17 2 Separate ground wire is required for Europe only 3 Use if the printer is to be used in Europe the Ferrite core and the cable should be separate as shown in Figure 18 CAUTION DO NOT connect any other plug to the peripheral unit connector Modular plug MOLEX 90075 0007 AMP641337 or JAPAN BURNDY B 66 4 Shield Wire lead O Separated Ground wire connected to shield Europe only Cable specifications for peripheral unit Ferrite core Ground wire Separate ground wire and noise filter are required for Europe 34 x a Z o lt Drive circuit The recommended drive circuit is shown Drive output 24V max 1 0 A F G 242 With shield 2 7 I TRI DI y i 8 Peripheral unit 1 3 MGND 4V La 1 R3 TR2 J D2 47 La 1 4W l 5 I o i M GND Peripheral l unit 2 ET 5V Compulsion switch ia E EA RI n R2 ak Frame ground NOTES 1 Peripheral units 1 and 2 cannot be driven simultaneously When driving a device continuously do not use drive duty above 20 2 Compulsion switch status is available as status data Resistance for coils L1 and L2 is not less than 24 ohms 4 Absolute maximum r
19. polvere eccessiva e con la possibilit di accedere ad una fonte di alimentazione elettrica stabile non soggetta a sbalzi improvvisi di tensione Ad esempio non collegare la stampante sullo stesso circuito elettrico di grossi apparecchi che producono disturbi come frigoriferi o condizionatori d aria NOTA Assicurarsi che la tensione del proprio impianto elettrico corrisponda a quella specificata sulla piastrina di identificazione della stampante 19 2 IDENTIFICAZIONE E NOMENCLATURA DELLE PARTI Esaminare la Figura 2 1 per conoscere i componenti e le funzionalit della stampante Coperchio della stampante Pannello di controllo Taglierina della carta Protegge la testina di stampa e Indica lo stato della stampante e automatica gli altri componenti interni della semplifica il controllo delle Controllata tramite comando stampante funzioni della stampante TSP442 Z lt lt E TSP412 Barra di apertura Serve per aprire e chiudere l unit della testina di stampa che mantiene premuta la carta contro il rullo Connettore unit periferica Interruttore di alimentazione Serve per collegare la stampante ad Serve ad accendere e spegnere unit periferiche come registratori di la stampante Coperchio del cassa ecc connettore Connettore d interfaccia Serve per collegare la stampante al computer Fig 2 1 20 3 INSTALLAZIONE DEGLI ANELLI DI FERRITE SOLO EUROPA NOTA P
20. pu ter aus Stecken Sie das Schnittstellenkabel in die Buchse Vergewissern Sie sich daf das Kabel korrekt ausge richtet ist bevor Sie den Stecker einstecken Schnittstellenkabel HOSLNAG Buchse Ziehen Sie die beiden Schrauben links und rechts fest so daf der Stecker sicher an der Buchse befestigt ist Abb 4 1 Verbinden Sie das andere Ende des Kabels mit Ihrem Computer HINWEIS Die Daten bertragungsparameter von Computer und Drucker m s sen bereinstimmen Sie werden mit den DIP Schaltern des Druk kers eingestellt siehe Anhang 4 2 Parallele Centronics Schnittstelle CD Schalten Sie Drucker und Compu ter aus 2 Stecken Sie das Schnittstellenkabel SE in die Buchse Vergewissern Sie A sich da das Kabel korrekt ausge BN richtet ist bevor Sie den Stecker einstecken G Klammern Sie den Stecker an der Buchse fest Abb 4 2 Verbinden Sie das andere Ende des Kabels mit Ihrem Computer 17 INDICE 1 APERTURA E CONTROLLO DELLA CONFEZIONE 19 1 1 Apertura della confezione 19 1 2 NATIO A seinen 19 2 IDENTIFICAZIONE E NOMENCLATURA DELLE PARTI 20 3 INSTALLAZIONE DEGLI ANELLI DI FERRITE SOLO EUROPA 21 Installazione dell anello di ferrite del cavo d interfaccia 22 Installazione dell anello di ferrite del cavo dell unit periferica 22 4 COLLEGAMENTO DEL
21. re des pr cautions sp ciales en suivant les proc dures indiqu es ci dessous Deux filtres antibruit tore de ferrite un grand et un petit sont emball s avec l imprimante Le petit filtre antibruit est pr vu pour le c ble d interface s rie 3 RS232C et le grand doit tre utilis pour le c ble de p riph rique gt Z Q Code du Code du gt 09990728 A 09990723 2 produit produit Nom du Tore de ferrite Nom du Tore de ferrite 924mm mod le 20 10 10 928mm mod le TFC 23 11 14 Pour le c ble d interface Pour le c ble de peripherique Les tores de ferrite sont livr s ouverts comme indiqu la Fig 3 2 Si un tore de ferrite n est pas ouvert utiliser un objet pointu pour forcer le verrouillage en plastique du tore de ferrite Fig 3 1 Lorsque c est le cas prendre soin de ne pas endommager le tore de ferrite ni le verrouillage en plastique Petit tore de ferrite diam tre 24 mm Interface Fig 3 3 C ble Fig 3 2 Faire passer attache autour du c ble et la bloquer Couper toute partie qui d passe avec des ciseaux Fig 3 4 9 Installation du tore de ferrite de c ble d interface Serrer le petit tore de ferrite au c ble d interface de la mani re indiqu e la Fig 3 2 Prendre les pr cautions d usage pour viter d endommager le c ble d interface lors de l installation du tore de ferrite Il faut bien immo
22. restare particolare attenzione durante l esecuzione delle procedure indicate di seguito Insieme alla stampante vengono forniti in dotazione due anelli di ferrite uno grande e uno piccolo da utilizzare come filtri per la soppressione di eventuali disturbi Il filtro antidisturbi piccolo va fissato sul cavo d interfaccia seriale RS232C mentre quello grande serve per il cavo di collegamento di unit periferiche Codice Codice prodotto 09990728 prodotto 09990723 Anello di ferrite Anello di ferrite 24mm Modello TE C 20 10 10 928mm Modello TEC 1e Per il cavo d interfaccia Per il cavo dell unit periferica Gli anelli di ferrite sono confezionati aperti come mostrato in Fig 3 2 Se si trova uno degli anelli di ferrite chiuso aprirlo utilizzando un oggetto appuntito per far leva sul dispositivo di chiusura di plastica dell anello di ferrite Fig 3 1 Fare attenzione a non danneggiare il nucleo di ferrite o Abb 3 1 il dispositivo di chiusura di plastica zi gt E gt 2 Distanza massima 5 cm Anello di ferrite piccolo diametro 24 mm Interfaccia verso l anello di ferrite Fig 3 3 Tirare e tagliare Cavo Fig 3 2 Far passare la fascetta di fissaggio intor no al cavo e bloccarla Tagliare la parte in eccesso con delle forbici Fig 3 4 91 Installazione dell anello di ferrite del cavo d interfaccia Bl Fissare l anello di ferrite piccolo
23. ripheral unit cable ferrite core however you have to loop the cable as shown in Fig 3 5 Large ferrite core 28mm diameter One loop Ground wire Fig 3 5 4 CONNECTING THE INTERFACE CABLE 4 1 RS 232C or RS 422A Serial interface Follow the procedures below to connect the interface cable HSITON3 CD Switch off the power to the printer and computer 2 Insert the interface cable into the connector Be sure that the cable is oriented correctly before inserting it Interface cable 3 Fasten the right and left screws to Interlace connector fix them in place on the connector Connect the other end of the inter face cable to your computer Fig 4 1 NOTE The data transfer conditions between the computer and the printer must be made compatible with the DIP switch settings on the printer Refer to APPENDIX 4 2 Centronics type Parallel interface CD Switch off the power to the printer and computer Insert the interface cable into the connector Be sure that the cable is lt oriented correctly before inserting it Fasten the connector clasps 4 Connect the other end of the inter Fig 4 2 face cable to your computer TABLE DES MATIERES 1 DEBALLAGE ET INSPECTION scsi 7 l 1 Deballage cir id f io 7 1 2 Remarques sur la manipulation 7 2 IDENTIFICATION DES PIECES ET NOMENCLATURE 8 3 INSTALLATION DU TORE DE FERRITE EUROP
24. sul cavo d interfaccia come mostrato in Fig 3 2 facendo attenzione a non danneggiare il cavo d interfaccia L anello di ferrite va saldamente bloccato in posizione con la fascetta di fissaggio fornita in dotazione come mostrato nelle Fig 3 3 e 3 4 Installazione dell anello di ferrite del cavo dell unit periferica BI Fissare l anello di ferrite grande sul cavo dell unit periferica eseguendo la stessa procedura vista per l anello di ferrite del cavo d interfaccia Tuttavia quando si applica l anello di ferrite sul cavo dell unit periferica necessario fare un cappio al cavo come mostrato in Fig 3 5 Distanza di 5 cm o inferiore Anello di ferrite grande diametro 28 mm e Z lt ar lt E Filo di terra Cappio Fig 3 5 ZI 4 COLLEGAMENTO DEL CAVO D INTERFACCIA 4 1 Interfaccia seriale RS 232C o RS 422A Per collegare il cavo d interfaccia eseguire le procedure indicate di seguito Spegnere sia la stampante che il computer Inserire il cavo d interfaccia nel connettore assicurarsi che il cavo sia orientato nel senso corretto pri ma di inserirlo Cavo d interfaccia T 3 Stringere le due viti di destra e sini Connettore d interfaccia stra per fissare il connettore Collegare l altra estremit del cavo d interfaccia al computer Fig 4 1 zi gt gt 2 NOTA Le caratteristiche di trasferimento dati tra il computer
25. uitable place we mean e Close to an easily accessible socket outlet e A firm level surface which is fairly vibration free e Away from excessive heat such as direct sunlight heaters etc e Away from excessive humidity e Away from excessive dust e With access to a steady power supply that is not subject to power surges For example do not connect the printer to the same circuit as a large noise producing appliance such as a refrigerator or an air conditioner NOTE Make sure that the line voltage is the voltage specified on the printer s identification plate 2 PARTS IDENTIFICATION AND NOMENCLATURE To get acquainted with the printer s components and capabilities refer to Figure 2 1 Printer cover Protects the print head and other internal components of your printer I o l Z Control panel LU Indicates printer status and makes control of printer functions simple and convenient Automatic paper cutter Controlled by command TSP442 Release bar TSP412 Opens and closes the print head unit which holds the paper against the platen Power switch 4 i Peripheral drive connector Switches power on or off Only connects to peripheral units Connector cover such as each drawers etc Interface connector Connects the computer to the printer Fig 2 1 J 3 FERRITE CORE INSTALLATION EUROPE ONLY NOTE Take special care when following the procedures listed below
Download Pdf Manuals
Related Search