User manual - GOED licht en geluid
Contents
1. bright velocity CH5 light 1 0 255 G From dark to bright Electronic reset CH6 light 1 0 255 B From dark to bright Function table of 14 Channels CH7 light 1 0 255 W From dark to bright l CH8 light 2 0 255 R From dark to bright Function Numerical CH9 light 2 Q 255 G From dark to bright Dimming for all O 255 From dark to bright CH10 light 2 0 255 B From dark to bright CHII light 2 0 255 W From dark to bright2. es eter tn eee Sk a pee te pin2 Data Compliment negative Pinl ground pin2 data true negitive pin3 data compliment positive 4 Menu Instructions Four buttons and their funcation Return Return to last saved menu mode discontinue current operating state Up Add key Down Decrease key Enter To enter or save current operating state or adjust the dmx value MENU DISPLAY Menu 1 DMX 512 Auto show to Slave when connected to be slave CH stroboscopic fast 0 slow 0 255 Motor rotation 0 255 RGBW From dark 10 brighi Switch for motor auto O 255 RGBW From dark to bright running O 255 RGBW From dark to bright 0 255 RGBW From dark to brighi 0 255 RGBW From dark to bright 0 255 RGBW From dark to bright Function table of 10 Channels Q 255 RGBW From dark to bright 0 255 RGBW From dark to bright Function Numerical Colorful color O 210 Built in colorful color jump Dimming for all O0 255 From dark to bright jump 211 gt 255 Colortul How O 9 Full bright 10 255 Stroboscopic from 13 Colortul flow 0 255 f owo 0 255 Motor rotation 0 255 From dark to bright Function table of 39 Channels 0 255 From dark to bright Channe wo 0 255 From dark to bright 0 255 From dark to bright CH1 Dimming for all 0 255 From dark to bright Colorful color 0 210 Built in colorful color jump CH2 a ee Stroboscopic from Jump 211255 Colorful flow CH3 Motarfetalen Se flow 0553 slow CH4 light 1 0 255 R From dark to
3. User manual his GLG Lighting products Before use please read this manual 1 Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and ire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when its cover is removed Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if t becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the units main power Always mount this unit in safe and stable matter 2 Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and
4. a soft cloth towipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture Operates 1 e smoke fogresidue dust dew 3 Trouble Shooting Listed below are a few common problems the user may encounter with solutions Unit not responding to DMX Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound Quiet or high pitched sounds will not activate the unit If problems are not resolved contact Note To exit the Menu Operation Please press the Menu Button for Three Seconds Long Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 10 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances in cluding amplifiers th
5. at produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibit marked change in performance DMX 512 DMX is short for Digital Multiplex This is a universal used as a form of communication between intelligent fixtures and controllers A DMX controller sends 3 DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATAIN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX com pliant To ensure proper DMX data transmission when using several DMxX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of l may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no m
6. atter where it 1s located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation Your unit and your DMX controller require a standard 3 pin XLR connector for data S Figuret input and data output Figure 1 If you are making your own cables be sure to use standard two conductor shielded cable This cable may be purchased at almost all pro sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and can not be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground plug on the XLR connector Do not connect the 6 Main Features LEDs Voltage Packing size GW DMX Led 8 4in1 10w 110 260v 50 60Hz 118 50 36 cm 4pcs package SKg 39Channel CHIA His CHI6 CHIT CHIS CHI9 CH20 CH2 CH2 CHD CH24 CH25 CH26 CH27 CHS a MacroFmeon CH37 Colorful color 0 210 Built in colorful color jump jump 211 255 Colorful flow eee 0 255 from slow to fast wea CH39 Electronic reset fo ee a a SS ee XLR Pin Configuration 1 roun Cold zoll Nu roun pinl Ground A O N i pin2 Data Compliment negative er Hot ot pin3 Data true positive a a a cs ees nee a es ese ee eee ee Se ee DMX512 OUT DMX512 IN 3 PIN XLR COMMON 3 PIN XLR DMX DMX Dt
Download Pdf Manuals
Related Search