IC-F29SR Operating Instructions
Contents
1. To attach To remove Battery release buttons ji To attach To detach 1 ACCESSORIES Accessory attachments Continued Jack cover Y CAUTION The transceiver meets IP67 requirements Z for dust tight and waterproof protection only when Y the jack cover or the optional HM 168LWP SPEAKER Z MICROPHONE is attached To attach the jack cover 1 Place the jack cover over the speaker microphone jack 0 2 Insert and tighten the screws To detach the jack cover 1 Unscrew the screws using a Phillips screwdriver 2 Detach the jack cover 099 Section 2 PROGRAMMABLE KEY FUNCTIONS Programmable key functions If you use the CS F29SR CLONING SOFTWARE purchase separately you can assign the functions described be low to TOP Upper and Lower Y NOTE Refer to the instruction sheet that comes with Z the transceiver for the default settings of these keys SCAN START STOP Push to start and cancel a scan e When a scan is started with the Power ON Scan or Auto matic scan function push this key to pause it The paused scan resumes after a set time period PRIORITY A CHANNEL PRIORITY B CHANNEL Push to select the Priority A or Priority B channel PRIORITY A CHANNEL REWRITE PRIORITY B CHANNEL REWRITE Push to select the Priority A or Priority B channel Hold down to set the operating channel as the Prior ity A or Priority B channel MEMORY CHANNELS2. to turn OFF the transceiver power 2 Set ROTARY SELECTOR to any channel other than Channel 16 3 While holding down Lower rotate VOL to turn ON the power to enter the Beep level adjustment mode 4 Push Lower to turn the Beep function ON or OFF e When a beep sounds after pushing Lower the Beep bo function is ON When no beep sounds after pushing Po Lower the Beep function is OFF e f desired push Upper to adjust the Beep level See Upper e page 6 for details Lower 5 Rotate VOL to turn OFF the power to exit the Beep level adjustment mode 4 SETTINGS Setting the beep level You can adjust the beep level between 1 and 5 or 1 linked and 5 linked When a linked option is selected you can adjust the beep level by rotating VOL ID D Rotate VOL to turn OFF the transceiver power 2 Set ROTARY SELECTOR to any channel other than Channel 16 3 While holding down Lower rotate VOL to turn ROTARY SELECTOR ON the power and enter the beep level adjustment mode 4 Push Upper to change the beep level as shown to the right e A beep sounds every time you push Upper Therefore Pushing you can determine the current level setting by the in Upper creasing loudness of the beep that sounds
3. 17 2 3 4 Push to select memory channel 1 2 3 or 4 MONI Push to turn the CTCSS DTCS mute ON or OFF While holding down this key the transceiver opens any squelch or releases any mute LOCK Hold down to turn the Key Lock function ON or OFF e Even when the Lock function is ON MONI and SUR VEILLANCE are not locked SURVEILLANCE Hold down to turn ON the Surveillance function Push to turn OFF the function e When this function is ON and a signal is received a beep does not sound and the status indicator does not light even if you push any key Upper s r Lower e J SIREN Hold down to emit a siren sound e The transceiver keeps emitting the siren sound until the transceivers power is turned OFF e This function is for situations other than an emergency alert such as a security alarm SCRAMBLER Hold down to turn ON the Voice Scrambler function Push to turn OFF the function COMPANDER Hold down to turn ON the Compander function Push to turn OFF the function e The Compander function reduces noise components from the transmitted audio to provide clear communica tion S RING C RING Push to make a Smart Ring call Hold down to make a Call Ring call ANNOUNCE Push to turn the Channel Announce function ON or OFF e The transceiver announces the position of Rota
4. the power to exit the CTCSS tone setting mode NOTE e If you make a mistake go back to step D and follow all the steps again e If you want to enter 0 do not push PTT in step and D just push Upper Then zero will be an nounced To turn OFF the CTCSS tone enter OO MMA DA Example CTCSS tone No 28 162 2 Hz assigned to channel 4 D Rotate VOL to turn OFF the power 2 While holding down PTT Upper and Lower rotate VOL to turn ON the power e The transceiver enters CTCSS tone Setting mode 3 Rotate ROTARY SELECTOR to select channel 4 then hold down Upper until two beeps sound 4 Push PTT two times to enter 2 the ten s digit of the number 28 Push Upper e Two will be announced Push PTT eight times to enter 8 the one s digit of the number 28 D Push Upper to complete the setting e Eight will be announced 8 Turn OFF the power to set the CTCSS tone ROTARY SELECTOR PTT 1s Upper Lower e Y e Available CTCSS tone list 4 SETTINGS Setting the group code number Continued DTCS code setting This transceiver is equipped with 84 DTCS codes DTCS operation enables silent standby since you will only receive calls from group members using the same DTCS code D Rotate VOL to turn OFF
5. O ICOM OPERATING INSTRUCTIONS PMR446 TRANSCEIVER IC F29SR Icom Inc INTRODUCTION FOREWORD Thank you for purchasing this Icom transceiver IMPORTANT FIRST CAREFULLY READ INSTRUCTIONS that are provided with the transceiver SAVE THIS OPERATING INSTRUCTIONS These operating instructions contain additional important operating instructions for the IC F29SR PMR446 TRANS CEIVER TABLE OF CONTENTS FOREWORD aaa aaa sen ag aia leiden aa ga A ag a TE aa KN NA ORTAN kasa aan Danan aa aaa an ng a a eet a aaa ana naa a an thea tas TABLE OP CONTENT Siete a adana 1 ACCESSORIES renenunnunnunnunannnnnannwnnunennanun 1 2 Accessory attachments ccccsccesssssseeeseeeeeeees 1 Battery DAGCK anasak a aa a a S 1 Bel GD aa aaa aa aka AN dace aa E AK NG uaa etees 1 Jack COVE aks a aa aa A ee 2 2 PROGRAMMABLE KEY FUNCTIONG 3 Programmable key functions c00sseeeeee 3 3 LED INDICATOR cccccssscneesssensscneseneesseeneeens 4 About the LED indicator ccccsseseesseneeeeeees 4 4 SETTINGS veccacestccceceiecicdseccaaecccecancencetucteestcuacace 5 11 Setting the Beep function sseeeesseeeeees 5 Setting the beep level sssecsesseeeeeneeeeees 6 Setting the ringer level ccccsssseesseesseeeeeeees 7 Setting the group code number 02 000 8 CTCSS tone Setting ccccecceee
6. de Upper 6 rLower 10 4 SETTINGS Setting the squelch level The squelch circuit mutes the received audio signal depending on the signal strength D Rotate VOL to turn the transceiver power OFF 2 Set ROTARY SELECTOR to any channel other than Channel 16 3 While holding down Upper rotate VOL to turn ON the power and enter the squelch level adjust ment mode 4 Push Upper to increase the squelch level tight squelch or push Lower to decrease the squelch level loose squelch e The adjustable range is O open squelch and 1 loose squelch to 9 tight squelch eA beep sounds after pushing Upper or Lower An error beep sounds if you try to exceed the adjustable range 7 NOTE The Beep function should be turned ON p 5 5 Rotate VOL to turn OFF the power to exit the squelch level adjustment mode 11 D ROTARY SELECTOR PD Q e ooo ooo SS Upper 5 Lower e we Count on us Icom Inc 2014 Icom Inc 1 1 32 Kamiminami Hirano ku Osaka 547 0003 Japan A 7150 3EU
7. eeeeeeeeeeeeeees 8 DTCS Code Setting ccccecccsececeeeeeseeeeeees 9 Setting the microphone gain c0ssseeeee 10 Setting the squelch level sscceeseeees 11 Icom Icom Inc and the Icom logo are registered trademarks of Icom Incorporated Japan in Japan the United States the United King dom Germany France Spain Russia and or other countries All other products or brands are registered trademarks or trademarks of their respective holders Section 1 ACCESSORIES Accessory attachments Battery pack Attach or remove the battery pack as illustrated to the right To attach the battery pack 1 Place the tabs on the bottom of the battery pack into the slots at the bottom of the transceiver b 2 Push the battery pack until the battery release but tons make a click sound To remove the battery pack Push the battery release buttons in the direction of the arrow as shown to the right 2 The battery pack is then released and you can re move it 09 Belt clip ZY NOTE Before attaching or detaching the belt clip Y remove the battery pack from the transceiver if it is Y attached To attach the belt clip Slide the belt clip in the direction of the arrow until the belt clip locks in place and makes a click sound O To detach the belt clip Lift the tab up Q and slide the belt clip in the direc tion of the arrow
8. i eer Pe e To determine if you have selected a linked level set VOL 4 l to minimum then push Upper repeatedly listening for Ce the loudest beep level 5 Pushing Upper once after Upper al T the loudest beep will select 1 Linked Repeatedly push ni Upper to select the desired linked level Lower 5 5 Rotate VOL to turn OFF the power to exit the beep level adjustment mode Na eel l 5 Linked A 4 Linked A 3 Linked A 2 Linked A 1 Linked 4 4 SETTINGS Setting the ringer level You can adjust the ringer level between 1 and 5 or 1 linked and 5 linked When a linked option is selected you can adjust the ringer level by rotating VOL Rotate VOL to turn OFF the power 2 Set ROTARY SELECTOR to Channel 16 3 While holding down Lower rotate VOL to turn ON the power and enter the ringer level adjustment mode 4 Push Upper to increase or push Lower to de crease the ringer level as shown to the right eA beep sounds after pushing Upper Therefore you can determine the current level setting by the increasing loudness of the beep that sounds e To determine if you have selected a linked level set VOL to minimum then push Upper up to 10 times listening for the loudest beep level 5 Pushing Upper once after the loudest beep will select 1 Linked Repeatedly push Upper or Lower to select the desired linked level 5 Rotate VOL to turn OFF
9. rs DTCS Code Setting mode 3 Rotate ROTARY SELECTOR to select channel 5 then hold down Lower until two beeps sounds 4 Push PTT one time to enter 1 the ten s digit of the number 16 Push Upper e One will be announced Push PTT six times to enter 6 the one s digit of the number 16 D Push Upper e Six will be announced 8 Push PTT again to use Inverse mode 9 Push Upper to complete the setting OTurn OFF the power to set the DTCS code NAN PTr 6 mi r Lower e i e Available DTCS code list 4 SETTINGS Setting the microphone gain Higher levels make the microphone more sensitive to the user s voice D Rotate VOL to turn OFF the power 2 Set ROTARY SELECTOR to Channel 16 3 While holding down Upper rotate VOL to turn ON the power and enter the microphone gain adjust ment mode 4 Push Upper or to increase or push Lower to de crease the microphone gain e The adjustable range is 1 minimum to 4 maximum A beep sounds after pushing Upper or Lower F An error beep sounds if you try to exceed the adjustable a range PAJ I 7 NOTE The Beep function should be turned ON p 5 Rotate VOL to turn OFF the power to exit the mi yi crophone gain adjustment mo
10. ry Selec tor Z NOTE When the Beep function is OFF the operat Y ing channel is not announced regardless of this set Z ting p 5 Section 3 LED INDICATOR About the LED indicator The LED indicator indicates the status of various pa rameters of the transceiver as follows Reference R is Red G is Green O is Orange e Cloning reading or writing data e Cloning error if cloning fails e Inh Blank CH Unlocked when you cannot use the channel RIO RIO RIO RIO RIO RIO RIO RIO e TX Low Battery 1 while transmitting E RT R i e TX Low Battery 2 while transmitting M R O R R a Transmitting e Receiving 16 LL e Scanning l a NG e Low Battery 1 You should charge the battery Gy e Low Battery 2 You must charge the battery e When turning ON the power RJOJG RO JG MH e Making a Smart Ring call o o 0 ol 0 oj e Lockout TX Inh TOT when transmit is inhibited Rmo o 0 i e Smart Ring call successful O G a e Smart Ring call failed O Pa Gt e Siren clok a o r celojn a o R Section 4 SETTINGS Setting the Beep function The Beep function can be turned ON or OFF When it is OFF the channel announcement is also turned OFF 4 NOTE You should turn ON the Beep function when you set the microphone gain the squelch level or the Y group code number to check the current level setting Z with the beep sounding pp 8 11 MA ROTARY SELECTOR D Rotate VOL
11. the power 2 Set ROTARY SELECTOR to any channel other than Channel 16 3 While holding down PTT Upper and Lower rotate VOL to turn ON the power 4 Rotate ROTARY SELECTOR to select the desired channel 1 to 16 that you want to assign the DTCS code to 5 Hold down Lower until two beeps sound e The transceiver enters the DTCS code setting mode 6 Push PTT the necessary number of times to en ter the ten s digit of the desired DICS code number grey column as shown in the list below D Push Upper e The selected number will be announced 8 Push PTT the necessary number of times to en ter the one s digit of the desired DICS code number grey column as shown in the list below 9 Push Upper e The selected number will be announced Olf you want to use Inverse mode push PTT again e If you want to use Normal mode skip this step Push Upper to complete the setting 2Turn OFF the power to exit the DTCS Code Setting mode NOTE e f you make a mistake go back to step D and follow all the steps again e f you want to enter 0 do not push PTT in step and just push Upper Then zero will be announced To turn OFF the DTCS code enter 0 Example DTCS code No 16 114 Inverse mode as signment to channel 5 D Rotate VOL to turn OFF the power 2 While holding down PTT Upper and Lower rotate VOL to turn ON the power e The transceiver ente
12. the power to exit the ringer level adjustment mode ROTARY SELECTOR Pushing Upper etemmm ee ny Pushing Lower 4 Upper Lower e J 4 Linked A 3 Linked A 2 Linked A 1 Linked 4 4 See 4 SETTINGS Setting the group code number CTCSS tone setting The transceiver is equipped with 50 CTCSS tones CTCSS operation enables silent standby since you will only receive calls from group members using the same CTCSS tone 1 Rotate VOL to turn OFF the power 2 Set ROTARY SELECTOR to any channel other than Channel 16 3 While holding down PTT Upper and Lower rotate VOL to turn ON the power 4 Rotate ROTARY SELECTOR to select the desired channel 1 to 16 that you want to assign the CTCSS tone to Hold down Upper until two beeps sound e The transceiver enters the CTCSS tone setting mode Push PTT the necessary number of times to enter the ten s digit of the desired CTCSS tone number grey column as shown in the list below D Push Upper e The selected number will be announced 8 Push PTT the necessary number of times to enter the one s digit of the desired CTCSS tone number grey column as shown in the list below 9 Push Upper to complete the setting e The selected number will be announced 0 Turn OFF
Download Pdf Manuals
Related Search