ASA-S2000M/S2500M
Contents
1. screwdriver will increase the torque Turning it counterclockwise out of the screwdriver will decrease the torque Note The engraved markings on the engraving ring are for reference only and do not indicate torque output Torque output can only be determined by repeated testing with a torque meter or hand held spanner torque meter To prevent your torque setting from being changed we can provide a torque cover optional which covers and secures the regulating handle Bit insertion Use your finger to depress the slide sleeve into the screwdriver and insert an appropriate bit When the slide sleeve is released the bit will be automatically engaged Note Do not hammer the bit in or pull it out forcibly Secure screwdriver during operation During operation hang the screwdriver up securely as from balancer in order to prevent it from being knocked down and suffering external cracking internal damage or a snapped power cord When the selected torque is reached This product features an internal clutch assembly When a screw is driven and the selected torque is reached the clutch assembly will automatically disengage and a click will be heard At this point even if the forward trigger is not released the power to the motor will be automatically cut off Note When driving screw grasp the screwdriver firmly in order to prevent upwards recoil generated by the clutch release from forcing the screwdr2. After use Storage and maintenance when the unit is to be stored for a long period remove the power supply and bit open the carbon brush cover and blow out any accumulated carbon brush dust with compressed air and wipe the exterior clean Then store the screwdriver carefully in a dry dust free place away from direct sunlight Store the bit in grease To ensure continued serviceability periodically check and maintain the screwdriver Troubleshooting If the screwdriver does not work properly check the list below If you cannot solve the problem do not open the unit Contact one of our authorized agents as soon as possible If the screwdriver does not run Check that the power supply is outputting power Check that the power supply plug is inserted properly and that output plug terminals No 1 and NO 4 show 30VDC approximate between them If no output is shown change the power supply use plug type 2G2021 5P or purchase equivalent type e Check that the rotation direction switch are working properly If no click is heard when a trigger is depressed it is not working and must be replaced make sure to perform this check in a quiet place If the screwdriver is not rotating normally e There is a protective circuit within the power supply Power is only supplied normally from 3 to 5 seconds after current flow begins If the motor only runs intermittently during Forward operation try Reverse
3. Determine the appropriate torque range choose the correct screwdriver for the torque you will require To lengthen product life avoid long term high torque use Make sure the screwdriver is undamaged If the power code is scraped or damaged it should be immediately unplugged and replaced to avoid electric shocks or a short circuit that could result in fire Use in an appropriate work environment To ensure safety do not use in high temperature high humidity environments or near flammable materials Keep the power cord away from tools or equipment that might scrape or melt it When plugging in or unplugging the power cord hold the plug firmly Never pull on the cord Method of operation and important points Driving and removing screw insert the tip of the screwdriver bit accurately into the screw slot and press down lightly To drive a screw depress the Forward trigger To remove a screw depress the Reverse lever Either of these actions will automatically engage the motor If both the Forward and Reverse levers are depressed at the same time the screwdriver will not rotate Note During operation do not switch quickly between rotation directions Release one lever and wait for the motor to stop fully before depressing the other lever Torque settings Use the regulating handle to set the torque Turning it in a clockwise direction into the
4. Outline This drawing applies only to 49 bit shank screwdrivers 158 6 2 FORWARD HANGER LEVER RING aL 256 HAR TOT panora 621660 8 W REVERSE BIT SLIDE REGULATING ENGRAVING LOWER HANDEL RING Accessories This product comes supplied with a 5P connector wire and two bits Bits one set per screwdriver 1 lt L _ O _E J 24 i 4 4 OS fos Bit specifications Available Tip N Tip diameter d Pi Pi Screwdriver PO 440 164 d4 1 4 Model 00 21 7 7W120 7W6201 ASA S2000M 0 62 0 7W142 7W6421 HO 92 0 7W142 7W6421 ASA S2500M 1 23 0 7W164 7W6421 1 Power supply optional Dimension mm Operation volt Output volt weight Model L w H AO DO g 1b Approval APM 30 80 48 55 90V 260V 30V 200 0 4 Pending 115V A3 144 100 58 230V 20V 30V 1800 4 0 Pending e APM 30 are switching circuit power supplies They are light and small consume little electricity and supply stabile voltage Before use read the following Use the correct voltage Carefully check the voltage shown on the power supply and this manual and determine the correct voltage Only plug the unit into a power source of the correct voltage
5. SIGN CHECKED ASA ENTERPRISE CORP APPROVED TEL 02 8751 0022 10 Line DWG NO MI 0034 P r cej w sd a DATE NAME ipis S2000M S2500M REVISED 2 2506 L I C DRAWN 2004 10 06 ARE RIES Coss Seli P SYM DESCRIPTION DATE SIGN CHECKED ASA ENTERPRISE CORP APPROVED TEL 02 8751 0022 10 Line DWG NO MI 0 0 32
6. operation or rotate the anvil 90 degrees until a click is heard then re attempt Forward operation e Long term use causes the motor s commutator to wear down In this case it must be replaced this repair must be performed by one of our authorized agents If the bit falls out easily or wobbles e check that the bit matches our specifications If not change the bit to one that does Check that the bit is inserted tightly into two guide channels within the anvil If not remove the bit and re insert it tightly If the bit tends to wobble remove the bit rotate it 180 degrees and re insert it If the screwdriver does not stop when the selected torque is reached An excessive torque setting can cause the screw to strip the threads with the result that the clutch does not activate Lower the torque to a level that does not cause stripping Differences in size between the bit tip and screw slot lengths can cause slopping Change to a suitable bit tip e The brake circuit may be damaged or the sensor switch may have shifted this repair must be performed by one of our authorized agents Warranty We provide a 3 years free repair service warranty with this swiss motor product The warranty is good for one year from the date of purchase entered on the Product Information Form The retailer s stamp must appear on the form to confirm the date However the following circ
7. ing circuit for precision torque control low breakdown rate and long product life Connecting with soft start and speed adjustable function power supply not only match to differ fastening condition but also keep the best fastening quality Design features separation of screwdriver and control for low repair costs and higher serviceability rate Switching power supply plugs directly into screwdriver and supplies stabile voltage provides more accurate torque and longer motor life Right angel 90 head adapter attaches easily to screwdriver for use in small spaces gt 60mm operates smoothly Optional Ample torque easy to control not necessary to switch unit direction before switching direction of rotation user can switch direction directly Ergonomically designed exterior reduces work fatigue and increases productivity Specifications Model ASA S2000M ASA S2500M Power source 30VDC Torque range kgf em Ibf in 0 3 2 0 0 26 1 7 0 4 3 0 0 35 2 6 No load speed rpm 1000 650 Torque setting Stepless 2 eee 1 0 2 2 0 04 0 09 1 0 2 6 0 04 0 10 85 mm in 5 gt 4 Tapping Screw 1 0 2 0 0 04 0 08 1 0 2 0 0 04 0 08 mm in Weight g 1b 187 0 41 Length mm in 158 6 2 4 0 173 6 81 1 4 Available bit shank 94 0 1 4 Power consumption W 6W Available power supply A3 APM 30 Clutch impact Just one time when torque up
8. iver bit edge form the screw slot and damaging slot When removing screws when a previously driven screw cannot be removed using the same torque that it was driven with raise the torque setting After the screw is removed return the regulating handle to its original setting To simplify this operation note the number click sounds generated as the regulating handle is turned Operational frequency suggest the operational frequency 1 4 ON OFF second the total screws 7000pcs 8hours don t over our operational frequency suggest and avoid the inside part of screwdriver serious damage If everyday work 8hours upward please use two screwdriver by turns protect the life of screwdrivers Changing the carbon brush insert a slotted hand screwdriver with a 2mm to 4mm head edge into the slot and lever up the carbon maintenance bonnet Then remove the carbon brush fastener spring Loosen the carbon brush guide cord fastener screw and pull the carbon brush guide cord to remove the carbon brush Insert a new carbon brush and then follow the above steps in reverse order Note e When changing the carbon brush first unplug the screwdriver Use a factory specification carbon brush The notch on the carbon brush surface must face into the direction of the rotor rotate Guide for 5P plug in oe DATE NAME up ASA S2000M S2500M A REVISED 12 2506 L I C E s 1 4 bit holder type SYM DESCRIPTION DATE
9. umstances we will charge the user for any parts and labor cost associated with repairs For repairs involving normal wear to parts including carbon brushes bits and power cord and also to the exterior surface If the screwdriver was connected to a power source of the incorrect voltage If there was inappropriate use or an attempt to repair the unit by the user After the period of the guarantee or if the user cannot present the manual with stamped Product Information Form Retailer s Stamp Specifications and design may be changed without notice for improvement A 2 Serial No ASA Industrial Electric Screwdriver User s Manual for full automatic models low volt DC motor with controller A Word of Thanks to Our Customers Thank you for choosing lightweight and powerful electric screwdrivers In order to insure maximum performance and product life please read through this manual before using your screwdriver Feature Adopted the high precision low inertia and low impact driving swiss s motor long lift high quality Our screwdrivers are designed for use with precision torque locking screws It can be used for assembly of small items such as mobile phone cameras and eyeglasses and large items such as home appliances computers and furniture Low vibration low noise meets environmental protection demands Low voltage electronic brak
Download Pdf Manuals
Related Search
ASA S2000M/S2500M