GEC Floating electrode Steam Raiser User Guide
Contents
1. London Cablegrams Polyphase London Branches throughout Great Britain and in all the principal markets of the world H 0 9775 Revised June 1948 Printed in England HS2. FLOATING ELECTRODE STEAM RAISER Cat Maximum Load 20 kW No H 0 4980 Maximum Working Pressure 15 Ibs per sq in MADE IN ENGLAND PRESSURE GAUGE SOLUTION FUNNEL Lor FIXING SCREW a NEUTRAL SHIELD FLOAT EARTH CONNECTION WATER INLET AND DRAIN SAFETY VALVE STEAM STOP VALVE ELECTRODES FLOATING ELECTRODE STEAM RAISER INSTALLATION Unbolt and take off top cover of steam raiser and remove all packing material from interior Connect water supply to horizontal inlet on 3 way valve Mount control gear on wall and connect incoming mains and outgoing flexible cable in accordance with wiring diagrams provided with control panel If a pressure switch is not fitted make sure that the appropriate terminals in control panel are connected together If dash pots are fitted to overload trips fill them with the correct grade of oil Set overload trips at 25 above normal full load at which steam raiser is to operate Make sure that both internal and external connections are securely made STARTING UP With the top cover off half fill the steam raiser with water and turn off the cock Make sure that the electrode assembly floats freely and level in the water With the cover still removed switch on the current by means of the switch on the control panel The current will be indicated by the ammeter and will increase rapidly as the water heats up finally remaining steady when the water around the el
3. ectrodes boils This will take only a few minutes The position of the electrodes in the float must then be adjusted until the current is about 90 of the desired maxinrurtr value To adjust the electrodes switch off the current and slacken the three fixing screws A Then raise or lower the electrodes and neutral shield inside the float Raising the electrodes will decrease the current taken and lowering them will increase it Switch on again and observe the current Repeat the procedure until with the water boiling the current is 90 of the desired value The fixing screws A should then be tightened and the top cover bolted on When operating under pressure the current will rise slightly above the value obtained with the steam raiser open so giving the desired load Ifa pressure regulator is fitted set it to the required working pressure and adjust the differential The maximum load of 20 kW is obtained on 400V three phase with a current of 29 amps If the requisite current cannot be attained refer to Special Conditions overleaf ALWAYS DISCONNECT THE ELECTRICITY SUPPLY BEFORE CARRYING OUT ADJUSTMENTS FLOATING ELECTRODE STEAM RAISER Continued OPERATION Fill the steam raiser with water until the level in the gauge glass is about 2 inches from the top Switch on and the full output of steam will be obtained in a few minutes The steam raiser will operate for about 1 to 14 hours before requiring refilling with wat
4. eld and may be removed by scraping or employing a de scaling solution The contacts of the control panel should be inspected from time to time and if showing signs of burning should be cleaned with a smooth file A few drops of light machine oil should be applied occasionally to the bearings of the contactor switch SPECIAL CONDITIONS The steam raiser is suitable for use with the majority of water supplies In certain districts the nature of the water gives rise to conditions requiring special treatment Should it be found that the desired value of current cannot be obtained even though the electrodes are lowered to their fullest extent a small quantity of common salt should be added to the water to increase the current This should be Introduced through the filling cup and only sufficient usually a teaspoonful to give the desired load should be added Should the required load or more than the required load be obtained even though the electrodes are raised to their fullest extent special small diameter electrodes can be supplied If satisfactory results cannot be achieved a sample of the water about 1 quart in a clean sterile bottle should be sent to the G E C for testing ALWAYS DISCONNECT THE ELECTRICITY SUPPLY BEFORE CARRYING OUT ADJUSTMENTS Wholesale only THE GENERAL ELECTRIC CO LTD Head Office Telephone TEMple Bar 8000 90 lines MAGNET HOUSE KINGSWAY LONDON W C 2 Telegrams Electricity Westcent
5. er To shut down simply open the switch of the control panel With some water due to the precipitation of salts during evaporation the current may increase above the desired value The steam raiser should then be completely drained and refilled with fresh water In some instances to obtain stable working conditions it will be necessary te drain under pressure after each operation When working with the steam outlet fully open and no external back pressure the pressure on the gauge may fall to 1 Ib per square inch or less As the steam raiser gives constant evaporation at all times it will give a satisfactory performance providing the pressure is sufficient to drive the steam to where it is required Higher pressures are not required and may be detrimental to efficient sterilizing and e rubber components To obtain the maximum evaporation at all times the float should be adjusted to give the maximum evaporation at the lowest pressure which will give a satisfactory performance It is misleading to make comparisons with fuel fired steam raisers which work at high pressure to provide a r serve to deal with fluctuations in firing Such high pressures quickly fall when a steam raiser is working on full output MAINTENANCE When used with hard water periodical de scaling will be necessary the nature of the water determining how often this must be carried out The scale will be found to accumulate chiefly on the electrodes and neutral shi
Download Pdf Manuals
Related Search