Home

VK2-1080MD37W User manual

1. The event map allows you to change the settings and establish a schedule for each event trigger from the Network Camera You can register the event map up to max 15 Click Add button to make a new event map and you can see a popup window as below Add Event Map General Name New Event Event In Type Onboot Event Out E E mail To e mail address 1 To e mail address 2 To e mail address 3 To e mail address 4 To e mail address 5 To e mail address 6 To e mail address 7 To e mail address 8 Subject Additional info E FrP E HTTP server Message J Alarm out T Event Notification Boost LJ Record OK Cancel VK2 1080MD37W User manual V1 0 45 e General Enter the name for a new event map Event In Select an event type in the drop down list e Event Out E mail Select email addresses you want to send via email that an event has occurred FTP Select checkbox beside FTP to record and saves images to an FTP server when an event has occurred HTTP Server It sends notification messages to an HTTP server that listens for these The destination server must first be configured on the Event In page Enter a message you want to send Event Notification It sends XML messages to an Notification server that listens for these The destination server must first be configured on the Event In page Boost when an event has occurred the camera will boost the Framerate and Bitra
2. 4 The network camera s Live View page appears in your browser Q Stream 1 e H 704x480 kd ehe lel Live View SA LA 1 eS AVILES VK2 1080MD37W User manual V1 0 14 3 2 Access from the internet Access from the internet once connected the VK2 1080MD37W is accessible on your local network LAN To access the VK2 1080MD37W from the Internet you must configure your broadband router to allow incoming data traffic to the network camera To do this enable the NAT traversal feature which will attempt to automatically configure the router to allow access to the network camera This is enabled from Setup gt System gt Network gt NAT For more information please see 3 5 4 System gt Network gt NAT of User s Manual 3 3 Setting the admin password over a secure connection To gain access to the product the password for Connect to 192 168 12 210 the default administrator user must be set This is done in the Admin Password dialog which is displayed when the VK2 1080MD37W is accessed for the setup at the first time Enter Seger Cag OE Oe eae your admin name and password set by the UL UL LE administrator Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection Note The default administrator username is i 7 admin and password is admin If the password is peters a lost the VK
3. Automatic Automatic identification and compensation for the light source color This can be used in most situations and is the recommended setting Fixed Incandescent Fixed color adjustment ideal for a room with incandescent a glow lighting and good for a normal color temperature around 2600K Fixed Fluorescent Fixed color adjustment good for fluorescent lighting with a color temperature around 4000K to 5000K Fixed Outdoor Fixed color adjustment for sunny with a color temperature around 6500K to 7500K Y Day amp Night Video amp Image E Basic Configuration Day amp Night B Live View Pre Viewer Video amp Image Basic Image AE amp AWB Day amp Night Privacy Masking Webcasting amp Event amp System amp About 4 W724i LINTEO Day amp Night Control Mode Automatic Threshold High Save Reset e Day amp Night Control Select the day night mode from among three modes Mode Normally works in day mode It switches automatically to night mode in a dark place Automatic Normally works in day mode It switches automatically to night mode in a dark place Day Always works in day mode Night Always works in night mode VK2 1080MD37W User manual V1 0 28 e Threshold Select the day night mode threshold High quickly changes to day mode but slowly changes to night mode Low quickly changes to night mode but slowly changes to day mode Y Privacy
4. SmartManager i File View Help i EJ Model Name E NDT 7202 P NDT 7202 MAC Address IP Address O0 07 D8 17 48 40 192 168 30 225 D8 17 48 37 192 168 30 224 Wireless IP Address Zero Conf IP 0 0 0 0 169 254 109 2 0 0 0 0 169 254 191 1 Version 1 0 3 T7_release 1 0 3 T7_release Ca All Devices 15 H 26A Mini Dama a NDT 3211 1 al Remote Setup H NDT 6311 3 Quick View NDT 7202 2 R X NUT 6301D 2 an 4 a NVT 6303 1 a NVT 7202 5 H NVT 7254 1 Upgrade Firmware 2 LogIn Open Web Page Emergency Firmware Upgrade Camera Information Model NOT f202 Mame H 264 Mini Dome Mac Oddress 47 DE 6 DD 15 37 IP Address 192 166 30 220 Cancel Note For more information refer to the Smart Manger User s Manual VK2 1080MD37W User manual V1 0 13 3 Operation The VK2 1080MD37W can be used with Windows operating system and browsers The recommended browsers are Internet Explorer Safari Firefox Opera and Google Chrome with Windows NOTE To view streaming video in Microsoft Internet Explorer set your browser to allow ActiveX controls 3 1 Access from a browser 1 Start a browser Internet Explorer 2 Enter the IP address or host name of the VK2 1080MD37W in the Location Address field of your browser 3 You can see a starting page Click Live View or Setup to enter web page H 264 Mini Dome oJ Boe Ra Live View Playback Setup
5. Use passive mode Under normal circumstances the VK2 1080MD37W simply requests the target FTP server to open the data connection Checking this box issues a PASV command to the FTP server and establishes a passive FTP connection whereby the VK2 1080MD37W actively initiates both the FTP control and data connections to the target server This is normally desirable if there is a firewall between the camera and the target FTP server Remote directory Specify the path to the directory where the uploaded images will be stored If this directory does not already exist on the FTP server there will be an error message when uploading User name Password Provide your log in information VK2 1080MD37W User manual V1 0 38 JPEG Setting Pre event A pre event buffer contains images from the time immediately preceding the event trigger These are stored internally in the server This buffer can be very useful when checking to see what happened to cause the event trigger Check the box to enable the pre trigger buffer enter the desired total length in seconds minutes or hours and specify the required image frequency Post event This function is the counterpart to the pre trigger buffer described above and contains images from the time immediately after the trigger Configure as for pre event Prefix file name This name will be used for all the image files saved If suffixes are also used the file name will take the form lt prefix gt lt suf
6. 3 5 1 Basic Configuration You can see the device information in this information page Basic Configuration B Basic Configuration z Basic Configuration Users Manufacturer HITRON Network Model name NDT 7202 Video amp Image Device name H 264 Mini Dome Date amp Time Firmware version 1 0 3 T7_release MAC address 00 07 D8 17 48 37 IP address 192 168 30 224 Link Local IP address 169 254 191 1 Wireless IP address 0 0 0 0 Video mode NTSC B Live View Video amp Image B Event amp System EB About VK2 1080MD37W User manual V1 0 18 1 Users User access control is enabled by default An administrator can set up other users by giving these user names and passwords It is also possible to allow anonymous viewer login which means that anybody may access the Live View page as described below Basic Configuration Basic Configuration Users Users User Settin Network 9 Video amp Image V Enable anonymous viewer login Date amp Time User List Setting B Live View User Name User Group Authority B Video amp Image admin administrator live setup system Q Event ae ae E System B About Save Reset The user list displays the authorized users and user groups levels Authority Gus Provides the lowest level of access which only allows access to the Live View page An operator can view the Live View page create and modify Operator events and adjust certain other set
7. All Device L F Model Name Name MAC Address IP Address Wireless IP Address Zero Conf IP Version Ea All Devices 15 e NDT 3211 1 a NDT 6311 3 NDT 7202 2 NUT 6301D 2 Y a NVT 6303 1 H NVT 7202 5 H NVT 7254 1 ONVIF 9 E NvT 7202 H NoT 3211 EJ NOT 6311 EJ NDT 6311 EJ Nvt 7202 EJ NuT 6301D EJ NDT 6311 E Nvt 7202 H 264 Mini PT Dome H 264 Motorized Full HD H 264 Motorized 3M Cam H 264 Motorized 3M Cam H 264 Mini PT Dome H 264 Network Bullet Cam H 264 Motorized 3M Cam H 264 Mini PT Dome AC DE 48 DD 1F 0D 00 07 D8 17 06 EF AC DE 48 DD 21 07 AC DE 48 DD 21 05 AC DE 48 DD 1F 06 AC DE 48 DD 1D 02 AC DE 48 DD 21 00 AC DE 48 DD 1F 07 192 168 30 220 192 168 30 241 192 168 32 68 192 168 32 66 192 168 21 98 192 168 22 221 192 168 32 65 192 168 32 91 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 169 254 236 67 169 254 38 92 169 254 14 210 169 254 193 129 169 254 237 90 169 254 40 124 169 254 38 21 169 254 248 221 1 0 1 T7_release 1 8 6 T3_release 0 1 6 T6_isc 0 1 6 T6_isc 1 0 3 T7_release 1 2 7 T6_release 0 1 2 T6_test 1 0 3 T7_release E Group F NUT 6301D H 264 Network Bullet Cam AC DE 48 DD 1D 06 192 168 30 200 0 0 0 0 169 254 179 186 1 2 7 T6_release V f H Mehun Dame la a S a 3h LST Th release 3 Select the camera on the list and click right button of the mouse You can see the pop up menu below
8. Date Format YYYY MM DD S E Time Format 24 Hour Save Reset e Current Server Time It displays the current date and time 24h clock The time can be displayed in 12h clock format in the overlay see below e New Server Time Select your time zone from the drop down list If you want the server clock to automatically adjust for daylight savings time select the Automatically adjustment for daylight saving time changes From the Time Mode section select the preferred method to use for setting the time Synchronize with computer time sets the time from the clock on your computer Synchronize with NTP Server the VK2 1080MD37W will obtain the time from an NTP server every 60 minutes Set manually this option allows you to manually set the time and date e Date amp Time Format VK2 1080MD37W User manual V1 0 23 Specify the formats for the date and time 12h or 24h displayed in the video streams Select Date amp Time format from the drop down list Date Format Specify the date format YYYY Year MM Month DD Day Time Format Specify the date format 24Hours or 12 Hours 3 5 2 Video amp Image Vv Live View Live View amp Basic Configuration Source Live View Video Input Mode Source Video Mode NTSC amp Video amp Image amp Event E System E About e Video Input Mode Video Mode Save Reset Choose Video Mode you wish to use from the drop down list NTSC or PAL VK2 1080
9. Save Reset User access control is enabled by default when the administrator sets the root password on first access New users are authorized with user names and passwords or the administrator can choose to allow anonymous viewer login to the Live View page as described below e User Setting Check the box to enable anonymous viewer login to the VK2 1080MD37W without the user account When using the user account users have to try log in at every access e User List Setting This section shows a registered user account Enter a user name and password to be added and register them by pressing the Add button You can see the pop up window as below Add User User Setting Username gt Password gt Confirm password User group quest operator administrator VK2 1080MD37W User manual V1 0 48 Y HTTPS System E Basic Configuration Security HTTPS E Live View HTTPS Connection Policy Video amp Image Event Connection Mode HTTP amp HTTPS M System Private Certificate Information E Security and click Users HTTPS IP Filtering Note When private certificate does not exist default certificate is used Date amp Time Network Save Reset Language Maintenance Support B About For greater security the VK2 1080MD37W can be configured to use HTTPS Hypertext Transfer Protocol over SSL Secure Socket Layer That is all communication that would otherwise
10. VK2 VK2 1080MD37W User manual Please read this manual thoroughly before use and keep it handy for future reference VK2 1080MD37W User manual V1 0 2 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PROCUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance PRECAUTIONS Safety Installation Should any liquid or solid object fall into the cabinet Do not install the unit in an extremely hot or humid unplug the unit and have it checked by the qualified place or in a place subject to excessive dust personnel before operating it any further mechanical
11. B Live View Boost Setting Z ra T Enable boost Event Boost Stream Stream 1 Normal Condition Boost Condition Event In Event Out Framerate 25 25 SMTP E Mail Bitrate control CBR juke Bitrate 4000 Kbps 4000 Kbps HTTP Server Alarm Out Record Save Reset Event Notification Boost Event Map B System B About The Boost feature is used in conjunction with event detection When this feature is turned ON the Framerate and Bitrate in the boost condition can be set to a different value than the ones in the normal condition field When an event is detected the camera will boost the Framerate and Bitrate from the normal condition to this boosted level for the duration of the event Check the box to enable the service e Boost Setting You can set the condition in Normal and Boost mode Boot Stream Select a video stream for each condition in the drop down list Framerate Select a frame refresh rate per second for each condition in the drop down list Bitrate control Select VBR or CBR in the drop down list in Normal Condition You can t change it in Boost Condition Bitrate Select a value for each condition in the drop down list VK2 1080MD37W User manual V1 0 44 3 Event Map Event B Basic Configuration Event Map EB Live View Event Map List Video amp Image Event Name Event In Event Out Event New Event AlarmIn 1 AlarmOut Event In Event Out Add Modify Remove Event Map E System B About
12. Contents Description 2 222 22202 2ce0sneees scene sesesnesessessssessesessessssessesessssessssene T POMPON O EE E E 7 1 Key S IT 8 To Eayoul EE 9 Installation 4 4 10 Bal GANEA ET TIO EEE 10 2 2 NetWork Connection and IP Assignment ss8esseeacseeneeatee ee eE E 12 Operation 2 13 3 1 Access ionta TOST EEE REE 13 Oi ACCESS MOM ASN Erne zas 14 3 3 Setting the admin password over a secure Connection 14 JA EVE WCW PAJO ee E E E R E E E E E E E E E 15 39 VK210890MD37 W SEIU ARE 17 29d Basic COMMNQUIALIO NT eE 17 BD OS Sa cc a a a ee 18 PASS A 6 a ae a 19 STS TER Ws 0 oe aoa aa H a oe a ee a Tag 20 4 AUC Ha 22 920 2 BUM 23 CFS R Lee MAJE 24 SR sh 5 9 UMM ata acer a a a i ee a la ac 30 ee a a aa 30 ANS a OO ae aa a 36 1 Ae Sa 44 IOVS 2 0 Meenas nea ee ee eee a 46 CNA 0 a ee 46 Le a a 47 9 Dale Gx Ii esas essen aes aeaaea sae OOO 90 4 Network 2 2 0n nn nnn nnn nn nnn nnn ne nnn nnn nn nnn nc nnn nana nana nanan nana na as 50 oy eUe 62 6 MamtenanGG akr searee See aese seer eee eee ee eee See ee eee ese Seer eeeeeeee 62 E HIST 63 FO DDT a 66 O50 Play Da ania 6 S e 69 3 8 Resetting to the factory default settings 2 2 nnn 70 Ls sius TY 11 4 1 Troubleshooting e rA a a E E E manana e 11 4 2 AAM GONMECIION
13. VBR adjusts the bit rate according to the image complexity using up bandwidth for increased activity in the image and less for lower activity in the monitored area CBR allows you to set a fixed target bitrate that consumes a predictable amount of bandwidth As the bit rate would usually need to increase for increased image activity but in this case cannot the frame rate and image quality are affected negatively To partly compensate for this it is possible to prioritize either the frame rate or the image quality whenever the bit rate needs to be increased Not setting a priority means the frame rate and image quality are equally affected Frame rate Upon the real time play users should select a frame refresh rate per second If the rate is high the image will become smooth On the other hand if the rate is low the image will not be natural but it can reduce a network load GOP size Select the GOP Group of Picture size If users want to have a high quality of fast image one by one please decrease the value For the purpose of general monitoring please do not change a basic value Such act may cause a problem to the system performance For the details of GOP setting please contact the service center e Stream2 Setting Sometimes the image size is large due to low light or complex scenery Adjusting the frame rate and quality helps to control the bandwidth and storage used by the Motion JPEG video stream in these situations Li
14. Basic Configuration Live View Video amp Image Basic Image AE amp AWB Day amp Night Privacy Masking Webcasting Event System About Webcasting Webcasting HTML code Stream 1 Stream 2 Stream 3 lt HTML gt lt HEAD gt lt TITLE gt Web Viewer lt TITLE gt lt HEAD gt lt body onLoad onInit onUnload onClose gt lt div gt lt OBJECT id HX_Media codebase http 192 168 30 224 NautilusV20_DHInc classid clsid 731D29F4 2872 4542 B85F 539610D7CSDB standby Downloe width 512 height 368 align center hspace 0 vspace 0 gt lt OBJECT gt lt div gt lt HTML gt lt script gt var obj document getElementBylId HX_Media function oniInit obj Initialize 1 obj ViewLayout 0 obj Connect 0 192 168 30 224 1 stream1 80 3 0 0 obj SetMenuType 0 function onClose obj Disconnect 0 lt script gt 4 WW Note To use webcasting service the Enable Anonymous viewer login option must be checked Refer to 3 5 1 Basic Configuration gt Users for more details VK2 1080MD37W User manual V1 0 30 3 5 4 Event 1 Event in V On Boot Event B Basic Configuration lt Event In On Boot B Live View On Boot Setting Video amp Image 9 E Enable on boot Event Dwell time 1 180 sec Event In On Boot Save Reset Alarm In Manual Trigger Motion Network Loss Event Out Event Map amp System B About This
15. Host Configuration Protocol DHCP and Domain Name System DNS or configure each computer s network settings manually which may be difficult and time consuming Zeroconf is built on three core technologies VK2 1080MD37W User manual V1 0 59 e Assignment of numeric network addresses for networked devices link local address auto configuration e Automatic resolution and distribution of computer hostnames multicast DNS e Automatic location of network services such as printing devices through DNS service discovery Y Bonjour The VK2 1080MD37W includes support for Bonjour When enabled the VK2 1080MD37W is automatically detected by operating systems and clients that support this protocol System B Basic Configuration Network Bonjour B Live View Bonjour Configuration B Video amp Image E 9 V Enable Bonjour B Event Friendly name NDT 7202 0007D8174837 System Save Reset Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Zeroconf Bonjour VSAAS Wireless Language Maintenance Support E About Note Bonjour Also known as zero configuration networking Bonjour enables devices to automatically discover each other on a network without having to enter IP addresses or configure DNS servers Bonjour is a trademark of Apple Computer Inc VK2 1080MD37W User manual V1 0 60 Y VSAAS VSaaS takes video monitoring into the cloud VSAAS referred to as hosted or managed
16. Mail server Port Connections security None Enable use SMTP authentication User name Password Login method AUTH LOGIN SMTP E Mail Receiver Receiver 1 Receiver 2 Receiver 3 Receiver 4 Receiver 5 Receiver 6 Receiver 7 Receiver 8 SMTP E Mail Test Receiver Save Reset 86400 sec 100 The VK2 1080MD37W can be configured to send event and error email messages via SMTP Simple Mail Transfer Protocol SMTP E Mail Setting Select Enable to activate the SMTP operation Mail Server Port Enter the host names or IP addresses and port numbers for your mail server in the fields provided to enable the sending of notifications and image email messages from the camera to predefined addresses via SMTP Sender Enter the email address to be used as the sender for all messages sent by the Network Camera Interval Represents the frequency of the email notification when an event occurs Aggregate events Shows the maximum number of emails sent within each interval If your mail server requires authentication check the box for Use authentication to log in to this server and enter the necessary information User Name Password Enter the User Name and Password as provided by your network administrator or ISP Internet Service Provider To ensure that the login procedure is performed as securely as possible when using SMTP authentication you must define the weakest authentication method
17. Masking The privacy masking function allows you to mask parts of the video image to be transmitted You can set up to eight privacy masks and the color of privacy masks is black Video amp Image B Basic Configuration Privacy Masking B Live View Pre Viewer Video amp Image Basic Image AE amp AWB Day amp Night Privacy Masking Webcasting amp Event amp System amp About Privacy Masking Setting Enable privacy masking ID Name Delete 1 Mask Window x 2 Mask Window2 x Save Reset The privacy masks are configured by Mask windows Each window can be selected by clicking with the mouse It is also possible to resize or delete or move the window by selecting the appropriate window at the mouse menu on the video screen Select Delete Freeze To create a mask window follow steps VK2 1080MD37W User manual V1 0 29 1 Click the right button of mouse to see the mouse menu 2 Select New Privacy Mask in the mouse menu 3 Click and drag mouse to designate a mask window area You can also modify or delete a mask window index Select an index and then modify items or delete button Select Enable to activate the privacy masking function Vv Webcasting The VK2 1080MD37W can stream live video to a website Copy the HTML code generated on the screen and pastes it in page code of the website you want to display live video Video amp Image ws ei ra
18. are not affected are the boot protocol DHCP or static the static IP address the default router the subnet mask the system time Default The default button should be used with caution Pressing this will return all of the Network Camera s settings to the factory default values including the IP address e Upgrade Carry out the upgrade by importing an upgrade file and pressing the Upgrade button During the upgrade do not turn off the power of the Network Camera And try an access again after waiting five minutes or longer e Backup Save a setting value that users enter to the Network Camera to a user PC Restore Import and apply a setting value saved to a user PC Note Backup and Restore can only be used on the same unit running the same firmware This feature is not intended for multi configurations or for firmware upgrades 7 Support The support page provides valuable information on troubleshooting and contact information should you require technical assistance System amp Basic Configuration Support B Live View The log and report files can be useful for troubleshooting or contacting the support team 6 Video amp Image Logs amp Event System log information System Event Log Event log information Information Reports Security Date amp Time Server Report Important information of the server status Network The unit s parameters and their current settings Language Health Check Mai
19. enssins 12 a3 Proventive Ta 12 4 4 Product SP ECIIG ALON 2232see2ers2e seeps e e scan seeeseaeaeerecsaaeee 73 VK2 1080MD37W User manual V1 0 7 1 Description This manual applies to the VK2 1080MD37W mini dome camera These cameras are fully featured for security surveillance and remote monitoring needs They are based on the DSP compression chip allowing real time full frame rate Motion JPEG and H 264 or MPEG 4 video streams 1 1 Components The system comes with the following components Pou HO maa DOVE MET WOR CAMERA Mini Camera Installation CD Installation Guide Accessory Kit Template sheet Alarm Cable Notes 1 Check your package to make sure that you received the complete system including all components shown above 2 Adapter for DC 12V is not supplied VK2 1080MD37W User manual V1 0 8 1 2 Key Features s Brilliant video quality The VK2 1080MD37W offers the highly efficient H 264 video compression which drastically reduces bandwidth and storage requirements without compromising image quality Motion JPEG is also supported for increased flexibility e Triple streams The VK2 1080MD37W can deliver triple video streams simultaneously at full frame rate in all resolutions up to 1920 x 1080 using Motion JPEG and H 264 or MPEG 4 This means that several video streams can be configured with different compression formats resolutions and frame rates for different needs e Image setting adjustment The VK
20. in IEEE 802 11b g n wireless LAN 10 C 40 C 0 80 non condensing DC 12V 375mA 4 5W PoE 93mA 4 5W Power over Ethernet IEEE 802 3af Class0 55mm x 115 235g Operating Temperature Operation Humidity Power Consumption Dimensions H x Unit Weight VK2 1080MD37W User manual V1 0 73 System Requirement for Web Browser Operating System Microsoft Windows OS Series CPU Intel Core 2 Duo 2Ghz or higher 1GB RAM or more 10GB free disk or higher VGA AGP Video RAM 32MB or higher 1024x768 24bpp or higher General performance considerations When setting up your system it is important to consider how various settings and situations will affect performance Some factors affect the amount of bandwidth the bit rate required others can affect the frame rate and some affect both If the load on the CPU reaches its maximum this will also affect the frame rate The following factors are among the most important to consider High image resolutions and or lower compression levels or high bitrates result in larger images Frame rate and Bandwidth affected Accessing both Motion JPEG and H 264 video streams simultaneously Frame rate and bandwidth affected Heavy network utilization due to poor infrastructure Frame rate and Bandwidth affected Heavy network utilization via wireless router due to poor infrastructure Frame rate and bandwidth affected Viewing on poorly performing client PCs lowers perceive
21. is used to trigger the event every time the VK2 1080MD37W is started Select Enable to activate the motion event VK2 1080MD37W User manual V1 0 31 Y Event In Alarm In Event E Basic Configuration Event In Alarm In E Live View Alarm In Port 1 Setting E Video amp Image mes l 9 V Enable alarm in port 1 B Event Type NO E j 2 Event In Dwell time 3 1 180 sec On Boot Alarm In Save Reset Manual Trigger Motion Network Loss Event Out Event Map B System E About This page allows you to configure the input supported by the camera The Port can be given as Normally Open or Normally Close state and their Normal state can be configured An input will be inactive as long as its Normal state equals its Current state The 2 options for Normal state are NO Normally Open and NC Normally Close The input is activated when the Current state changes so that it no longer equals the Normal state s Alarm In Port 1 Setting Click the Enable alarm in port checkbox to enable the Alarm In port 1 Type The default setting is NO NO Normally Open As an example if the Normal state for a pushbutton connected to an input is Open circuit this means that as long as the button is not pushed and the Current state remains as Open circuit the state will be inactive NC Normally Close When the button is pushed the circuit is grounded the input s state changes to Grounded circuit and the input will n
22. switch the DSCP value in the IP header tell the router or switch which type of treatment to apply to this type of traffic for example how much bandwidth to reserve for it Note that DSCP values can be entered in decimal or hex form but saved values are always shown in decimal The following types of traffic are marked Live Stream DSCP Event Alarm DSCP Management DSCP s Automatic Traffic Control Set a limitation on user network resources by designating the maximum bandwidth Maximum bandwidth In case of sharing other network programs or equipment it is possible to set a limitation on the maximum bandwidth in the unit of Mbit s or kbit s Auto frame rate Selected if not influenced by a network related program or equipment without a limitation on the network bandwidth VK2 1080MD37W User manual V1 0 57 Y NAT Traversal A broadband router allows devices on a private network LAN to share a single connection to the Internet This is done by forwarding network traffic from the private network to the outside that is the Internet Security on the private network LAN is increased since most broadband routers are pre configured to stop attempts to access the private network LAN from the public network Internet Use NAT traversal when your network cameras are located on an intranet LAN and you wish to make it available from the other WAN side of a NAT router With NAT traversal properly configured all HTTP tra
23. 2 1080MD37W also enables users to adjust image settings such as contrast brightness and saturation to improve images before encoding takes place e Micro SD Recording support The VK2 1080MD37W also supports a micro SD memory slot for local recording with removable storage e Improved Security The VK2 1080MD37W logs all user access and lists currently connected users Also its full frame rate video can be provided over HTTPS e Megapixel Resolution Max 30fps 1920x1080 e PoE This VK2 1080MD37W can be powered through PoE which simplifies installation since only one cable is needed for carrying power as well as video controls e ONVIF This is a global interface standard that makes it easier for end users integrators consultants and manufacturers to take advantage of the possibilities offered by network video technology ONVIF enables interoperability between different vendor products increased flexibility reduced cost and future proof systems VK2 1080MD37W User manual V1 0 9 1 3 Layout SSS Alarm Cable i SS qo Bauer Cable e T Ethernet Cable Description Cable for Power source DC 12V Cable for Ethernet POE 6 Camera Dimension See the diagrams below for the exact dimension Top View Side View Bottom View Dimensions Unit mm VK2 1080MD37W User manual V1 0 10 2 Installation 2 1 Camera Installation Carefully remove the contents from the box and verity that nothing was damaged in sh
24. 2 1080MD37W must be reset to the Remember my password factory default settings See 3 8 Resetting to the Factory Default Settings To prevent network eavesdropping when setting the admin password this can be done via an encrypted HTTPS connection which requires an HTTPS certificate see note below To set the password via a standard HTTP connection enter it directly in the first dialog shown below To set the password via an encrypted HTTPS connection see 3 5 6 System gt Security gt HTTPS Note HTTPS Hypertext Transfer Protocol over SSL is a protocol used to encrypt the traffic between web browsers and servers The HTTPS certificate controls the encrypted exchange of information VK2 1080MD37W User manual V1 0 15 3 4 Live View Page The live view page comes in several Q saeni Eoo gimme ol screen modes 1600x1200 1280x1024 Live View 1280x720 800x600 704x480 576 S E 640x480 352x240 288 and 320x240 Users are allowed to select the most Suitable one out of those modes Please adjust the mode in accordance with your PC specifications and monitoring purposes 1 General controls oF Live View Page G Search amp Playback Page jot Setup Page Help Page Ga The video drop down list allows you to select a customized or pre programmed video stream on the live view page Stream profiles are configured under Setup gt Basic Configuration gt Video amp Image For more information please see 3 5 1 Basic C
25. In On Boot Alarm In Manual Trigger Motion E 6 Portes Network Loss Event Out E 751 GTGT Event Map aN im n s T l cn J ea B System amp About Video Motion Detection Setting Enable video motion detection Day Day amp Night P Save Reset Motion detection is used to generate an alarm whenever movement occurs or stops in the video image A total of 8 Motion and or Mask windows can be created and configured Motion is detected in defined Motion windows which are placed in the video image to target specific areas Movement in the areas outside the motion windows will be ignored If part of a motion window needs to be masked this can be configured in a Mask window Pre Viewer Motion detection windows are configured by Motion or Mask windows Each window can be selected by clicking with the mouse It is also possible to resize or delete or move the window by selecting the appropriate window at the mouse menu on the video screen Mew Motion VK2 1080MD37W User manual V1 0 34 To create a motion or mask window follow steps 1 Click the right button of mouse to see the mouse menu 2 Select New Motion or Mask Window in the mouse menu 3 Click and drag mouse to designate a motion area s Motion Detection Setting The behavior for each window is defined by adjusting the Threshold and Sensitivity as described below A motion index is a set of parameters de
26. MD37W User manual V1 0 3 5 3 Video amp Image V Basic Video amp Image B Basic Configuration e Video amp Image Basic B Live View Stream 1 Setting R Video amp Image Codec H 264 Baseline Profile iw Basic l Resolution 1920x1080 im Image Bitrate control CBR lel AE amp AWB Bitrate 4000 Kbps Day amp Night l Framerate 25 lt Privacy Masking E GOP size 25 4 50 Webcasting B Event Stream 2 Setting ita Codec MJPEG m EB About Resolution 640x480 Te Framerate 30 e Quality 50 1 100 Stream 3 Setting Codec H 264 Baseline Profile e Resolution Same as Stream 2 e Bitrate control CBR Bitrate 1000 l Kbps Framerate 5 zl GOP size 5 1 10 Save Reset Refer to 3 5 1 Basic Configuration gt Video amp Image for more details VK2 1080MD37W User manual V1 0 25 Vv Image ea 5 5 ga Video amp Image Basic Configuration Image Live View Pre Viewer Video amp Image Basic Image AE amp AWB Day amp Night Privacy Masking Webcasting Event System About NA LA 1 eS NTE Image Appearance Brightness 5 default Contrast 5 o Saturation 5 default x Hue 1 default Sharpness 2 default E Enable flip image E Enable mirror image m Enable Noise Reduction Save Reset e Image Appearance This page pr
27. Multicast This function is for sending Video to Multicast group Enable Multicast Check the checkbox to enable multicast operation Multicast destination IP Enter an IP between 224 0 0 0 and 239 255 255 255 Although it is empty an IP will be entered automatically RTP port Enter a value between 1024 and 65530 RTP TTL Enter a value between 1 and 255 If a network status is smooth enter a lower value On the other hand if a network status is poor enter a higher value When there are many Network Cameras or users a higher value may cause a heavy load to the network For a detailed setting please consult with a network manager VK2 1080MD37W User manual V1 0 55 vV UPnP System B Basic Configuration Network UPnP Live View UPnP Configuration E Video amp Image G Enable UPnP B Event Friendly name NDT 7202 0007D8174837 System f Save Reset Information Security Date amp Time Network Basic DDNS RTP UPnP Qos NAT Zeroconf Bonjour VSAAS Wireless Language Maintenance Support E About The VK2 1080MD37W includes support for UPnP UPnP is enabled by default and the VK2 1080MD37W then is automatically detected by operating systems and clients that support this protocol Note UPnP must be installed on your workstation if running Windows XP To do this open the Control Panel from the Start Menu and select Add Remove Programs Select Add Remove Windows Components and o
28. P address e Gateway Priority Wireless In case of network connection through the wireless AP Wire In case of a wired network connection VK2 1080MD37W User manual V1 0 53 Y DDNS System B Basic Configuration B Live View B Video amp Image BH Event R System Information Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Zeroconf Bonjour VSAAS Wireless Language Maintenance Support B About Network DDNS Internet DDNS Dynamic Domain Name Service T Enable DONS Note Please remember you have to configure at least primary DNS server in DNS configuration settings to use Dynamic DNS DDNS Server cctv network co kr Registered host User name Password Confirm password Maximum time interval 1 hour Register local network IP address Registered IP address Save Reset e Internet DDNS Dynamic Domain Name Service When using the high speed Internet with the telephone or cable network users can operate the VK2 1080MD37W even on the floating IP environment in which IPs are changed at every access Users should receive an account and password by visiting a DDNS service like http www dyndns com or http www cctv network co kr Enable DDNS Check to get DDNS service to be available Username Enter an ID to access to the DDNS server VK2 1080MD37W User manual V1 0 54 Y RTP System amp Basic Configuration B Live Vi
29. address via DHCP EB Event use the following IP address IP address l Subnet mask Information s Default router S i S Security s Date amp Time ee Network i Network Select Basic SSID Security Signal Level RTP uni EDGE_RECORDER pa mE Qos oon mes Y a s Zeroconf IS_TEAM i z m B Bonjour VSAAS hitron adsl 3F a E Wireless SCAN Language Maintenance Save Reset Support E About e Network Select This list is the result of a network scan Access points with a disabled SSID Broadcast will not appear unless the camera is linked to it The VK2 1080MD37W is currently linked to is shown in blue A network using unsupported security is shown in grey The following information is provided SSID The name of a wireless network or ad hoc device If the same name occurs several times this means that several access points for that network were found The camera cannot be configured to only associate with one particular access point Security Shows which type of security the network uses See below for the security types supported by the camera Signal Level Shows the signal strength This VK2 1080MD37W has three security options e WPA WPA2 PSK e WPA WPA2 Enterprise e WEP WPA WPA2 Enterprise is more secure than WPA WPA2 PSK which in turn is more secure than WEP VK2 1080MD37W User manual V1 0 62 5 Language lt will be able to select a user language The type of
30. allowed VK2 1080MD37W User manual V1 0 37 Login Method Set the Weakest method allowed to the highest safest method supported by the mail server The most secure method is listed in the drop down list Login Plain e SMTP E Mail Receiver Receiver Enter an email address You can also register the e mail address of recipients up to 8 e SMTP E Mail Test Receiver Enter an email address and click the Test button to test that the mail servers are functioning and that the email address is valid Y FIP amp JPEG Event E Basic Configuration Event Out FTP amp JPEG B Live View FTP Setting E Video amp Image C Enable FTP R Event Server Event In Port Event Out Remote directory SMTP E Mail iiis FTP amp JPEG Password HTTP Server Alarm Out neil JPEG Setting Event Notification Pre event Time 5 0 30 sec Boost Post event Time 5 0 30 sec Event Map ees Prefix file name basename_ B System Additional suffix None Date Time E About Save sss 20 fps 1 21 fos When the VK2 1080MD37W detects an event it can record and save images to an FIP server Images can be sent as e mail attachments Check the box to enable the service e FTP Setting Server Enter the server s IP address or host name Note that a DNS server must be specified in the TCP IP network settings if using a host name Port Enter the port number used by the FTP server The default is 21
31. amera are valid for your network Check the client that the Enable multicast checkbox are enabled in the System Network RTP tab Checks with your network administrator to see if there is a firewall preventing viewing Multicast H 264 only accessible Check if your router Supports multicasting or if the router settings between the client and the server need to be configured The by local clients TTL value may need to be increased Color saturation is different in Modify the settings for your graphics adapter Please see the H 264 and Motion JPEG adapter s documentation for more information Check that the SD Card is inserted properly HE Check that the SD Card is formatted properly VK2 1080MD37W User manual V1 0 71 4 2 Alarm Connection The following connection diagram gives an example of how to connect a network camera Camera Inside Camera Outside E Mechanical Open collector Al switch Output switch Sensor Input DEC Power Alar rm Output Max Load 150mA Max Voltage DC 20 4 3 Preventive Maintenance Preventive maintenance allows detection and correction of minor that faults before they become serious and cause equipment failure Every three month perform the following maintenance 1 Inspect all connection cables for deterioration or other damage 2 Clean components with a clean damp cloth 3 Verify that all the mounting hardware is secure VK2 1080MD37W User manual V1 0 72 4 4 Product Specific
32. ate or End Date zone displays Search Calendar 7 Event List Window Event List displays the event s that were recorded in the SD local storage Select a list and click the play button The video clip will be played VK2 1080MD37W User manual V1 0 68 3 Help The Help information window will be provided as a popup window so that users can open and read it without a need for log in It will offer a description on setting and Help page by which users can manipulate the VK2 1080MD37W without a reference to the manual Help B View amp Playback Live View E Video amp Image B System Information Security Date amp Time Network Language Maintenance Support VK2 1080MD37W User manual V1 0 Support Support The Log and Reports provide a variety of information on troubleshooting and contact information should you require technical assistances Log The log file records event in the unit since the last system restart and can be a useful diagnostic tool when troubleshooting System Log The System Log provides information about system events Report The Report contains important information about the server Server Report The Server Report provides information about the server status and should be included when requesting report Information found here includes the camera s firmware version MAC address system information IP address and network connection
33. ation Mainittm Specification 1920 H x 1080 V 1 20 000 1 30 Slow shutter 1 15 1 8 and 1 4 Motion JPEG MPEG 4 Part2 video Compression H 264 MPEG 4 Part 10 Profiles H 264 HP MP and BP MPEG 4 SP Simultaneously H 264 or MPEG 4 and MJPEG Video Streaming Controllable Frame Rate and Bandwidth VBR CBR H 264 and MPEG 4 1920x1080 320x240 30fps 1920x1080 30fos 1280x720 TCP IP UDP IPv4 v6 HTTP HTTPS QoS FTP uPnP RTP RTSP RTCP DHCP ARP Zeroconf Bonjour Multi user authority HTTPS IP Filtering Privacy Zone Wireless WEP WPA PSK WPA2 WPS Software WPS setup Video Resolutions Frame Rate Protocol Security O Max Connection API Supported Open Platform Compatible ONVIF IN 1 Ext input Motion Detection Manual Trigger OUT 1 Ext output File upload via FTP and HTTP Notification via E mail HTTP and Pre and Post Alarm Yes max 8 programmable zone API Programming Interface Alarm IN OUT Alarm Events Video Buffering Motion Detection Network Time Synchronization SD Recording Software Reset Factory Reset Auto Recovery Installation Tool Upgrade Video out CVBS Ethernet TCP Pre and Post Namm Yes max 8 programmable zone Yes Yes Continuous Event Yes Yes Button Web browser Yes SmartManager VK2 Client Web browser SmartManager VK2 Client Yes with VK2 LCT not supplied RJ 45 10BASE T 100BASE TX Built
34. d performance Frame rate affected VK2 1080MD37W User manual V1 0 74 gL Pe CY CY VK2 1080MD37W User manual V1 0 75
35. ddress Remote directory Capacity ID Password Address Enter IP address for NAS device Remote Directory Enter directory or folder location to be recorded in the NAS device Capacity Enter the capacity of storage to be used It must be less than the total storage Capacity IP Password Enter ID and Password The VK2 1080MD37W will ask them whenever you access NAS device Check Press the Check button to check the validity of Device Setting data Format Click the Format button to format SD card Device Information Show current SD card information VK2 1080MD37W User manual V1 0 42 Y Event Notification Event EB Basic Configurati i i aa Event Out Event Notification B Live View Event Notification Setting Video amp Image Enable event notification Event Notification server URL Event In Notification server port Event Out SMTP E Mail Save Reset FTP amp JPEG HTTP Server Alarm Out Record Event Notification Boost Event Map amp System B About When the VK2 1080MD37W detects an event Notification Server is used to receive notification messages as a type of XML data format Check the box to enable the service e Event Notification Setting Notification Server URL The network address to the server and the script that will handle the request VK2 1080MD37W User manual V1 0 43 Y Boost Event B Basic Configuration Event Out Boost
36. dow follows 1 Video Screen You can see the video screen when playing the video clip in the Micro SD memory 2 Playback Buttons To view a recording data in the SD local storage select it from the list and click the Playback buttons 14 Go to the first go to the beginning of the video clip 4 Fast backward play 4 Backward play play backward of the video clip VK2 1080MD37W User manual V1 0 67 P Step backward play go back one frame of the video clip w Pause pause playback of the video clip K Step forward play go forward one frame of the video clip Forward Play play forward the video clip Fast forward play play fast forward of the video clip F Step forward play go forward one frame of the video clip Clip copy copy the video clip Zoom In zoom in the video clip oo DD Full Screen display full screen of the video 3 Time Chart Display an hour based search screen for the chosen date If there is recording data a blue section will be displayed on a 24 hour basis 4 Search Calendar Search results from the SD local storage in the VK2 1080MD37W connected are displayed monthly If there is a recorded data for a particular date a blue square on the date will be displayed 5 Play Time Displays time of the video playing 6 Event Search Window Select a search option in the drop down list and click GO button You can also enter the time period for searching If you click Start D
37. e and automate the assignment of IP addresses on a network DHCP is enabled by default Although a DHCP server is mostly used to set an IP address dynamically it is also possible to use it to set a static known IP address for a particular MAC address Use the following IP address To use a static IP address for the Network Camera check the radio button and then make the following settings IP address Specify a unique IP address for your Network Camera Subnet mask Specify the mask for the subnet the VK2 1080MD37W is located on Default router Specify the IP address of the default router gateway used for connecting devices attached to different networks and network segments Notes 1 DHCP should only be enabled if using dynamic IP address notification or if your DHCP server can update a DNS server which then allows you to access the VK2 1080MD37W by name host name If DHCP is enabled and you cannot access the unit you may have to reset it to the factory default settings and then perform the installation again The ARP Ping service is automatically disabled two minutes after the unit is started or as soon as an IP address is set Pinging the unit is still possible when this service is disabled VK2 1080MD37W User manual V1 0 20 3 Video amp Image Basic Configuration B Basic Configuration Video amp Image Users Stream 1 Setting Network Video amp Image Codec H 264 Baseline Profile Date a
38. evice Stream Type You can select Stream1 Stream2 or Stream3 Stream1 H 264 or MPEG 4 data Stream2 MJPEG data Stream3 You can select VIDEO or IMAGE Pre event Enter pre event time value for storage device pre recording Post event Enter post event time value for storage device post recording e Record Schedule You can set the weekly recording schedule for each day Drag or click area by a box unit at first Clicking the block toggles the recording between on and off Click the All Select button to set a schedule for the entire week or a whole day respectively VK2 1080MD37W User manual V1 0 41 e Device Setting Select Device Type to be recorded in the drop down list SD built in SD card CIFS A file format for a NAS device NFS A file format for a NAS device Note1 Common Internet File System CIFS is a remote file access protocol that forms the basis for Windows file sharing network printing and various other network services CIFS requires a large number of request response transactions and its performance degrades significantly over high latency WAN links such as the Internet Notez Network File System NFS is a network file system protocol allowing a user on a client computer to access files over a network in a manner similar to how local storage is accessed NFS like many other protocols builds on the Open Network Computing Remote Procedure Call ONC RPC system Device Setting Device Type A
39. ew amp Video amp Image amp Event System Information Security Date amp Time Network Basic DDNS RTP UPnP Qos NAT Zeroconf Bonjour VSAAS Wireless Language Maintenance Support 6 About Network RTP Port Range Start port 30000 End port Multicast Stream 1 Enable multicast Multicast destination IP 30000 39920 only even values are available 224 0 0 0 239 255 255 255 RTP port RTP TTL Always enable multicast Multicast Stream 2 Enable multicast 1024 65530 only even values are available 1 255 Multicast destination IP RTP port RTP TTL Always enable multicast Multicast Stream 3 E Enable multicast Multicast destination IP RTP port RTP TTL Always enable multicast 224 0 0 0 239 255 255 255 1024 65530 only even values are available 1 255 224 0 0 0 239 255 255 255 1024 65530 only even values are available 1 255 Save Reset Have a setting for sending and receiving a video on a real time basis These settings are the IP address port number and Time To Live value to use for the media stream s in multicast H 264 format Only certain IP addresses and port numbers should be used for multicast streams For more information please see the online help Port Range tart port Enter a value between 30000 and 39920 End port Enter a value between 30000 and 39920
40. ffic to an external HTTP port in the NAT router is forwarded to the network camera WAN Internet LAN ntranet Broadband NAT Router Port Forwarding Device Notes For NAT traversal to work this must be supported by the broadband router The broadband router has many different names NAT router Network router Internet Gateway Broadband sharing device or Home firewall but the essential purpose of the device is the same System B Basic Configuration Network NAT Port Mapping Live View Wire NAT traversal Setting Video amp Image Wire NAT traversal Setup External http port 10000 1024 65535 amp Event R System External rtsp port 10001 1024 65535 Information Security Note cabin i Ties If the Port is 0 the assigned port of network camera will be set automatically Network HTTP URL Basic DDNS RTSP URL RTP UPnP Wireless NAT traversal Setting Qos NAT Wireless NAT traversal Setup Zeroconf External http port 10000 1024 65535 Bonjour External rtsp port 10001 1024 65535 VSAAS Wirel ireless Note Language If the Port is 0 the assigned port of network camera will be set automatically Maintenance HTTP URL Support RTSP URL E About Save Reset VK2 1080MD37W User manual V1 0 58 e NAT traversal Settings Enable when enabled the VK2 1080MD37W attempt to configure port mapping in a NAT router on your network usi
41. fix gt lt extension gt Additional suffix Add either a date time suffix or a sequence number with or without a maximum value YV HTTP Server Event B Basic Configuration Event Out HTTP Server Live View HTTP Server Setting E Video amp Image Enable HTTP server R Event URL Event In Port Event Out User name SMTP E Mail FTP amp JPEG HTTP Server Password HTTP Server Test Send message Alarm Out Record Event Notification Boost Save Reset Event Map B System E About When the VK2 1080MD37W detects an event HTTP Server is used to receive uploaded image files and or notification messages Check the box to enable the service s HTTP Server Setting Name The name of the HTTP event server Use a descriptive name URL The network address to the server and the script that will handle the request For example http 192 168 12 244 cgi bin upload cgi User name Password Provide your log in information e HTTP Server Test When the setup is complete the connection can be tested by clicking the Test button VK2 1080MD37W User manual V1 0 39 VY Event Out Alarm Out Event amp Basic Configuration Event Out Alarm Out B Live View Alarm Out Port Setting E Video amp Image V Enable alarm out Event Type NO Event In Save Reset Event Out SMTP E Mail FTP amp JPEG HTTP Server Alarm Out Record Event Notification Boost Even
42. go via HTTP will instead go via an encrypted HTTPS connection e HTTPS Connection Policy Choose the form of connection you wish to use from the drop down list for the administrator Operator and Viewer to enable HTTPS connection set to HTTP by default HTTP HTTPS HTTP amp HTTPS e Upload Certificate To use HTTPS for communication with the Network Camera An official certificate issued by a CA Certificate Authority must be uploaded from your PC Provide the path to the certificate directly or use the Browse button to locate it Then click the Upload button Please refer to the home page of your preferred CA for information on where to send the request For more information please see the online help VK2 1080MD37W User manual V1 0 49 Y IP Filtering System Basic Configuration Security IP Filtering B Live View Video amp Image EB Event On Off R System Information Security Users HTTPS IP Filtering Date amp Time Network Language Maintenance Support B About IP Filtering Setting E Enable IP filtering Priority Policy Start IP End IP Save Reset Checking the Enable IP address filtering box enables the IP address filtering function Up to 256 IP address entries may be specified a single entry can contain multiple IP addresses Click the Add button to add new filtered addresses When the IP address filter is enabled addresses added
43. intenance Support Host Name NDT 72020007D8174837 E About S Services HTTP port 80 HTTPS port 443 RTSP port 554 ARP Ping setting Enable ARP Ping setting Save Reset Setting in regard to network can be executed Settings for IP DNS Host Name Port and ARP Ping can be established along with setting for DDNS uPnP QoS Zeroconfig Bonjour and wireless VK2 1080MD37W User manual V1 0 52 V Basic e IP Address Configuration Obtain IP address via DHCP Dynamic Host Configuration Protocol DHCP is a protocol that lets network administrators centrally manage and automate the assignment of IP addresses on a network DHCP is enabled by default Although a DHCP server is mostly used to set an IP address dynamically it is also possible to use it to set a static known IP address for a particular MAC address Use the following IP address To use a static IP address for the Network Camera check the radio button and then make the following settings IP address Specify a unique IP address for your Network Camera Subnet mask Specify the mask for the subnet the VK2 1080MD37W is located on Default router Specify the IP address of the default router gateway used for connecting devices attached to different networks and network segments e IPv6 Address Configuration Check this box to enable IPv6 Other settings for IPv6 are configured in the network router e DNS Configuration DNS Domain Name Service provides
44. ipment 1 Make screw holes for camera on the ceiling with Template Sheet 2 Disassemble a camera by Camera Cover 3 Fix the camera set using Anchors 2x and Screws 2x to the ceiling Camera Cover Dome Camera Template Sheet 4 Assemble Camera Cover to Dome Camera Turn Camera Cover clockwise to complete installation Lock clockwise VK2 1080MD37W User manual V1 0 11 Connecting to the RJ 45 Connect a standard RJ 45 cable to the network port of the network camera Generally a cross over cable is used for directly connection to PC while a direct cable is used for connection to a hub Micro SD memory slot Insert the SD memory card Connecting the Power Connect the DC 12V power adaptor to the camera Connecting the Wireless using WPS function Follow steps for a proper operation 1 Make sure your AP Access Point and Operating System support WPS Wi Fi Protected Setup functions WPS enables easy setup with compatible APs 2 Press the WPS button on the camera board You can then see the Status LED is blinking 4 Press and hold down the WPS button on your AP some router AP will have a virtual button on their management software instead Refer to your AP s documentation for details using its WPS functions When WPS configuration is done wireless connectivity will be established and the security encryption such as WEP or WPA PSK will be synchronized with the AP As for IP setting the camera s use of DHCP or sta
45. language it will be able to select is the English the French the German the Spanish and the Italian B Basic Configuration Language B Live View Language Setting Language English m EB Video amp Image amp Event System Save Reset Information E Security Date amp Time E Network Language Maintenance Support amp About 6 Maintenance E Basic Configuration S Maintenance EB Live View Maintenance Video amp Image Restart Restart the server B Event Reset all parameters except the IP parameters E System Reset all parameters to the factory settings Information Upgrade Security Upgrade the server with the new firmware Date amp Time l l Specify the firmware to upgrade E Network Language and click Maintenance Note Do not turn off the unit during flash upgrade The unit will restart automatically when the upgrade is finished 1 5 minites B About si Backup Save all parameters and user defined script to a backup file Restore Restore current configuration to backup file Specify the backup file to restore and click VK2 1080MD37W User manual V1 0 63 e Maintenance Restart The unit is restarted without changing any of the settings Use this method if the unit is not behaving as expected Reset The unit is restarted and most current settings are reset to factory default values The settings that
46. miting the frame rate and quality optimizes bandwidth and storage usage but may give poor image quality To prevent increased bandwidth and storage usage the Resolution Frame rate and Frame Quality should be set to an optimal value JPEG resolution Same as the Stream1 Setting JPEG frame rate Same as the Stream1 Setting VK2 1080MD37W User manual V1 0 22 JPEG quality Select the picture quality If users want to have a high quality of fast image one by one please decrease the value For the purpose of general monitoring please do not change a basic value Such act may cause a problem to the system performance e Stream Setting Same as the Stream1 Setting Click the checkbox to activate the 3 stream When satisfied with the settings click Save or click Reset to revert to previously saved settings 4 Date amp Time Basic Configuration Basic Configuration Date amp Time Users Current Server Time Network Video A Image Date 2013 05 15 Time 20 41 56 Date amp Time New Server Time amp Live View Time zone EB Video amp Image GMT Greenwich Mean Time Dublin Edinburgh Lisbon London l E Automatically adjusts for daylight saving time changes amp Event amp System Time mode amp About Synchronize with computer time Date s Time Synchronize with NTP server NTP server time nist gov NTP Interval 12 ll hour Set manually Date 2013 05 15 Time 20 41 55 Date amp Time Format
47. mp Ti l aana Resolution 1920x1080 lel Bitrate control CBR l E Live View Bitrate 4000 Kbps B Video amp Image Framerate 25 B Event GOP size 25 L S B System s Stream 2 Setting E About Codec MJPEG l Resolution 640x480 Framerate 30 Quality 50 1 100 Stream 3 Setting Codec H 264 Baseline Profile Resolution Same as Stream 2 l Bitrate control CBR l Bitrate 1000 Kbps Framerate 5 GOP size 5 2 e l Save Reset e Stream Setting Codec The codec settings are separated into MPEG4 and H 264 H 264 is also known as MPEG 4 Part 10 This is the new generation compression standard for digital video This function offers higher video resolution than Motion JPEG or MPEG 4 at the same bit rate and bandwidth or the same quality video at a lower bit rate Profile There are 4 pre programmed stream profiles available for quick set up Choose the form of video encoding you wish to use from the drop down list H 264 HP High Profile The primary profile for broadcast and disc storage applications particularly for high definition television applications for example this is the profile adopted by the Blu ray Disc storage format and the DVB HDTV broadcast service _ H 264 MP Main Profile Primarily for low cost applications that requires additional error robustness this profile is used rarely in videoconferencing and mobile applications it does add additional error resilience tools to the Const
48. ng UPnP Note that UPnP must be enabled in the VK2 1080MD37W see System gt Network gt UPnP automatic setting The VK2 1080MD37W automatically search for NAT routers on your network manual setting Select this option to manually select a NAT router and enter the external port number for the router in the field provided Notes If you attempt to manually enter a port that is already in use an alert message will be displayed When the port is selected automatically it is displayed in this field To change this enter a new port number and click Save Y Zeroconfig Zerocontig allows the VK2 1080MD37W to create and assign IP address for network cameras and connect to a network automatically System B Basic Configuration Network Zeroconf Live View Zeroconf Configuration Video amp Image p g 9 Enable Zeroconf B Event IP address S 169 254 191 1 System Save Reset Information Security Date amp Time Network Basic DDNS RTP UPnP Qos NAT Zeroconf Bonjour VSAAS Wireless Language Maintenance Support E About Zero configuration networking zeroconf is a set of techniques that automatically creates a usable Internet Protocol IP network without manual operator intervention or special configuration servers Zero configuration networking allows devices such as computers and printers to connect to a network automatically Without zeroconf a network administrator must set up services such as Dynamic
49. ntenance Support System Check Important information of system resources Media Check Video and audio stream information Network setting and traffic information lE Te Hardware diagnostic check amp About VK2 1080MD37W User manual V1 0 64 Logs The VK2 1080MD37W support system log information Click the System Log button to get the log data Reports Server Report Click the Server Report button to get the important information about the server s status and should always be included when requesting support Parameter List Click the Parameter List button to see the unit s parameters and their current settings e Health Check System Check Click the System Check button to get the important information about the camera s system resources You can see the pop up window below http 192 168 30 224 system check_system php System Check Model Firmware Date amp Time Date 2013 05 15 Time 20 43 30 Running time 11 hour 13 min CPU 254 Ss 2E 99 Media Check Click the Media Check button to get the information about the camera s video and audio stream You can see the pop up window below http 192 168 30 224 system check_media php Video stream Stream On Off Codec Size FPS Bitrate Streami On H 264 Baseline Profile 1920x1080 22 3307 Kbps Stream2 On MJPEG 640x480 27 2022 Kbps Stream3 On H 264 Baseline Profile 640x480 5 938 Kbp
50. ntrol settings for the network camera Mode Supports exposure modes to control the amount of light detected by the camera sensor based on settings for light conditions The default setting is Auto with DC IRIS Automatic Automatically sets the amount of light detected by the DC IRIS and AGC Hold Current Fixes the exposure at its current state Value Select a value in the drop down list to tune the exposure The default setting is 5 AGC Select a value in the drop down list to specify the level according to the screen luminance The default setting is 30dB Enable Backlight Compensation Set this checkbox to activate the BLC operation Flicker Mode Provides the options for flicker 50Hz Select at 50 Hz environments 60Hz Select at 60 Hz environments Enable Long Exposure Set this checkbox to activate the electronic shutter of the camera White Balance Control VK2 1080MD37W User manual V1 0 27 Max Shutter Select a shutter speed value in the drop down list The default setting is 1 15 This adjusts the relative amount of red green and blue primary colors in the image so that the neutral colors are reproduced correctly The camera can be set to automatically adjust for the type of light and compensate for its color Alternatively the type of light source can be set manually From the drop down list select the white balance setting suitable for the lighting used for your camera The available options are
51. o longer be in its normal state it will have become active An input on the camera has an Open circuit when disconnected or when there is a voltage Dwell time The default setting is 60 seconds Dwell time means how long time the alarm input signal hold on as an input signaling source Click the Save button to save the settings or click the Reset button to clear all of the information you entered without saving it VK2 1080MD37W User manual V1 0 32 Y Manual Trigger Event 2 Basic Configuration z Event In Manual Trigger B Live View Manual Trigger 1 Setting Video amp Image T Enable manual trigger 1 Event Dwell time 1 180 sec Event In s Manual Trigger 2 Setting On Boot Alarm In T Enable manual trigger 2 Manual Trigger Dwell time 1 180 sec Motion Network Loss Manual Trigger 3 Setting Event Out J E Enable manual trigger 3 Event Map Dwell time 1 180 sec B System Manual Trigger 4 Setting Ra About E Enable manual trigger 4 Dwell time i 1 180 sec Save Reset This option makes use of the manual trigger button provided on the live view page which are used to start or stop the event type manually Alternatively the event can be triggered via the product s API Application Programming Interface VK2 1080MD37W User manual V1 0 33 Y Motion amp Basic Configuration s s Event In Motion B Live View Pre Viewer E Video amp Image R Event E Event
52. onfiguration gt Video amp Image of User s Manual CJ The resolution drop down list allows you to select the most suitable one out of video resolutions to be displayed on live view page out of video resolutions to be displayed on live view page fe ihtTe 7 The protocol drop down list allows you to select which combination of protocols and methods to use depends on your viewing requirements and on the properties of your network 2 Control toolbar The live viewer toolbar is available in the web browser page only It displays the following buttons m The Stop button stops the video stream being played Pressing the key again toggles the start and stop The Start button connects to the VK2 1080MD37W or start playing a video stream u The Pause button pause the video stream being played er The Snapshot button takes a snapshot of the current image The location where the image is saved can be specified fq The digital zoom activates a zoom in or zoom out function for video image on the live screen 53 The Full Screen button causes the video image to fill the entire screen area No other windows will be visible Press the Esc button on the computer keyboard to cancel full screen view The Manual Trigger button activates a pop up window to manually start or stop the event VK2 1080MD37W User manual V1 0 16 3 Video Streams The VK2 1080MD37W provides several images and video stream formats Your requirements and the p
53. ovides access to the advanced image settings for the network camera Brightness The image brightness can be adjusted in the range 1 10 where a higher value produces a brighter image Contrast The image contrast can be adjusted in the range 1 10 Saturation Adjust the image s contrast by raising or lowering the value in this field Hue The image hue can be adjusted in the range 1 10 Sharpness Controls the amount of sharpening applied to the image A sharper image might increase image noise especially in low light conditions A lower setting reduces image noise but the image would be less sharp Enable flip image Check this box to flip the image Enable mirror image Check this box to mirror the image Enable Noise Reduction Check this box to reduce an image noise VK2 1080MD37W User manual V1 0 26 Y AE amp AWB Video amp Image amp Basic Configuration B Live View Video amp Image Basic Image AE amp AWB Day amp Night Privacy Masking Webcasting amp Event amp System amp About AE amp AWB Pre Viewer k c T Exposure Co Mode SSE Value 5 default E AGC 30 m dB F Enable Backlight compensation E Enable Flicker free Flicker Mode 60Hz E Enable Long Exposure Max Shutter 4 15 A White Balance Control Mode Automatic lel 4 Ali Pe 9 ANN Reset Exposure control This page provides access to the advanced exposure co
54. pen the Networking Services section Click Details and then select UPnP as the service to add VK2 1080MD37W User manual V1 0 56 Y QoS Quality of Service QOS provides the means to guarantee a certain level of a specified resource to selected traffic on a network Quality can be defined as a maintained level of bandwidth low latency and no packet losses The main benefits of a QoS aware network are The ability to prioritize traffic and thus allow critical flows to be served before flows with lesser priority Greater reliability in the network thanks to the control of the amount of bandwidth an application may use and thus control over bandwidth races between applications System B Basic Configuration Network QoS B Live View DSCP Setting Video amp Image Live stream DSCP 0 0 63 B Event Event Alarm DSCP 0 0 63 E Satam Management DSCP 0 0 63 Information Automatic Traffic Control Security Date amp Time T Enable automatic traffic control Network Maximum bandwidth Basic Mbit s Priority Framerate DDNS Automatic framerate control RTP UPnP Save Reset QoS NAT Zeroconf Bonjour VSAAS Wireless Language Maintenance Support E About e DSCP Settings For each type of network traffic supported by your network video product enter a DSCP Differentiated Services Code Point value This value is used to mark the traffic s IP header When the marked traffic reaches a network router or
55. plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been moisture does not operate normally or has been dropped CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO Use satisfy clause 2 5 of IEC60950 1 UL60950 1 or Certified Listed Class 2 power source only ITE is to be connected only to PoE networks without routing to the outside plant VK2 1080MD37W User manual V1 0 6 1 3
56. rained Baseline Profile The importance of this profile is fading after the Constrained Baseline Profile has been defined H 264 BP Baseline Profile Originally intended as the mainstream consumer profile for broadcast and storage applications the importance of this profile faded when the High profile was developed for those applications VK2 1080MD37W User manual V1 0 21 MPEG4 SP Simple Profile Mostly aimed for use in situations where low bit rate and low resolution are mandated by other conditions of the applications like network bandwidth device size etc Resolution It enables users to determine a basic screen size when having an access through the Web Browser or PC program The screen size control comes in seven modes like 1920x1080 1280x720 640x480 352x240 and 320x240 Users can reset the selected screen size anytime while monitoring the screen on a real time basis Bitrate control Limiting the maximum bit rate helps control the bandwidth used by the H 264 or MPEG 4 video stream Leaving the Maximum bit rate as unlimited maintains consistently good image quality but increases bandwidth usage when there is more activity in the image Limiting the bit rate to a defined value prevents excessive bandwidth usage but images are lost when the limit is exceeded Note that the maximum bit rate can be used for both variable and constant bit rates The bit rate can be set as Variable Bit Rate VBR or Constant Bit Rate CBR
57. roperties of your network will determine the type you use The Live View page in VK2 1080MD37W provides access to H 264 MPEG 4 and Motion JPEG video streams and to the list of available video streams Other applications and clients can also access these video streams images directly without going via the Live View page VK2 1080MD37W User manual V1 0 17 3 5 VK2 1080MD37W Setup This section describes how to configure the network camera and is intended for product Administrators who have unrestricted access to all the Setup tools and Operators who have access to the settings for Basic Live View Video amp Image and System Configuration You can configure the VK2 1080MD37W by clicking Setup in the top right hand corner of the Live View page Click on this page to access the online help that explains the setup tools Connect to 192 168 12 210 x When accessing the VK2 1080MD37W for the first time FO the Admin Password dialog appears Enter your b admin name and password set by the administrator The server 192 1668 12 210 for IP cameras requires a Username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection Note If the password is lost the VK2 1080MD37W User name must be reset to the factory default settings See 3 8 Password Doo O OS Resetting to the Factory Default Settings Remember my password
58. rrective Actions The camera cannot be If using a proxy server try disabling the proxy setting in your accessed by some clients browser Check all cabling and connectors The camera works locally but Check if there are firewall settings that need to be adjusted not externally Check if there are router settings that need to be configured If using a network switch check that the port on that device uses connection the same setting for the network connection type speed duplex Check that the host name and DNS server settings are correct accessed via a host name arena When HTTPS is enabled ensure that the correct protocol HTTP Not possible to log in or HTTPS is used When attempting to log in you may need to manually type in http or https in the browser s address bar If images are very complex try limiting the number of clients slow updating of images accessing the camera Check the Video amp Image setting Blurred images Refocus the camera Increased lighting can often improve image quality Check that Poor image quality there is sufficient lighting at the monitored location Check all image and lighting settings Try adjusting the Exposure Control setting under AE and AWB in image part H 264 not displayed in the Check that the correct network interface is selected in the Video client amp Image Stream Check with your network administrator that the multicast Multicast H 264 not displayed in addresses used by the c
59. rver Time Select your time zone from the drop down list If you want the server clock to automatically adjust for daylight savings time select Automatically adjustment for daylight saving time changes From the Time Mode section select the preferred method to use for setting the time Synchronize with computer time sets the time from the clock on your computer Synchronize with NTP Server the VK2 1080MD37W will obtain the time from an NTP server every 60 minutes Set manually this option allows you to manually set the time and date Note Note that if using a host name for the NTP server a DNS server must be configured under TCP IP settings VK2 1080MD37W User manual V1 0 51 4 Network E Basic Configuration Network Basic E Live View IP Address Configuration Video amp Image W Obtain IP address via DHCP E Event Use the following IP address ae wo ao 4 System IP address 22 Subnet mask 5 25 25 O Information S Default router 2 te ae d Security Date amp Time IPv6 Address Configuration Network Basic E Enable IPv6 DUNS IPv6 address fe80 207 d8ff fe17 4837 64 RTP UPnP DNS Configuration QoS f R Obtain DNS server via DHCP l Use the following DNS server address Zeroconf l Domain name Bonjour VSAAS Primary DNS server to to 8 4 Wireless Secondary DNS server r E EE Language Host Name Configuration Ma
60. s Parameter List The Parameter List shows the server s parameters and their current settings Va ss 20 qq 69 3 8 Resetting to the factory default settings To reset the VK2 1080MD37W to the original factory settings go to the Setup gt System gt Maintenance web page described in 3 5 4 System gt Maintenance or use the Reset button on the network camera as described below SWZ WPS LED gt C WPS WPS Button On Board e Using the Reset Button Follow the instructions below to reset the VK2 1080MD37W to the factory default settings using the Reset button Switch off the VK2 1080MD37W by disconnecting the power adapter Press and hold the Reset button with a straightened paperclip while reconnecting the power Keep the Reset button pressed during about 2 seconds Release the Reset button The VK2 1080MD37W resets to factory defaults and restarts after completing the factory reset Oh T Caution When performing a Factory Reset you will lose any settings you have saved Default IP 192 168 30 220 VK2 1080MD37W User manual V1 0 70 4 Appendix 4 1 Troubleshooting Troubleshooting if problems occur verify the installation of the VK2 1080MD37W with the instructions in this manual and with other operating equipment Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information Problems Symptoms Possible Causes or Co
61. s Audio stream mee omon codes Semele volume _ mitrate Input 254 es 2E 99 Networks Check Click the Network Check button to get the information about the camera s network setting and traffic You can see the pop up window below VK2 1080MD37W User manual V1 0 65 A Ka IIS E http 192 168 30 224 system check_network php Network Check Wired configuration Current Status Connected DHCP Off IP address 192 168 30 224 Subnet mask 255 255 255 0 Gateway 192 168 30 1 DNS 168 126 63 1 Wireless configuration Current Status Disconnected Traffic Wired 28 Kbps Streaming service Number of users currently live Number of users currently playback Server connection Live Push Disconnected Event Push Disconnected VAY s 2E H Result Success C 24 es 2E HN VK2 1080MD37W User manual V1 0 66 3 5 6 About The following website will provide the support information for the VK2 1080MD37W information and operation 3 6 Playback The Playback window contains a list of recordings made to the memory card It shows each recording s start time length the event type used to start the recording calendar and time slice bar indicates if the recording is existed or not Playback R Event List B Event Search S All 2013 5 Tw 01 02 07 08 09 14 GS 16 21 22 23 28 29 30 The description of playback win
62. scribing Window Name Type Threshold Sensitivity and Dwell Time Window Types is one of Motion and Mask windows Threshold Sets up the threshold for the motion detection Sensitivity Sets up the sensitivity for the motion detection Dwell Time Set the hold time an event lasts for the specified hold time from the point of detection of a motion You can also modify or delete a motion index Select an index and then click the Modify or Delete button Select Enable to activate the motion window VK2 1080MD37W User manual V1 0 35 Y Network Loss Event EB Basic Configuration Event In Network Loss B Live View Network Loss Setting Video amp Image f 9 E Enable network loss Event Dwell time 1 180 sec Event In On Boot Save Reset Alarm In Manual Trigger Motion Network Loss Event Out Event Map B System B About This is used to trigger the event every time the network connection is failed Select Enable to activate the Network Loss event VK2 1080MD37W User manual V1 0 36 2 Event Out Y SMTP E Mail Event B Basic Configuration B Live View E Video amp Image Event Event In Event Out SMTP E Mail FTP amp JPEG HTTP Server Alarm Out Record Event Notification Boost Event Map B System EB About Event Out SMTP E Mail SMTP E Mail Setting Enable SMTP Sender Interval 1 Pa Aggregate events 1 Use mail server
63. t Map BE System E About s Enable alarm out Click the Enable alarm out checkbox to enable the Alarm Out port Type The default setting is NO NO Normally Open NC Normally Close Click the Save button to save the settings or click the Reset button to clear all of the information you entered without saving it VK2 1080MD37W User manual V1 0 40 Y Record B Basic Configuration B Live View Video amp Image Event Event In Event Out SMTP E Mail FTP amp JPEG HTTP Server Alarm Out Record Event Notification Boost Event Map amp System EB About When the VK2 1080MD37W detects an event it can record video stream in the Micro SD Memory not supplied or NAS Network Attached Device as a storage device Check the box to enable the service e Record Setting Event Out Record Record Setting Enable Record Y Overwrite Continuous Record Note Continuous Record is not available while using SD Stream Type Pre event 0 0 10 sec Post event 0 0 60 sec Record schedule No Recording ZZ Recording All Select All Delete Device Setting Device Type Format Device Status No Storage Device Remove Remova Device Information Total Used Available Used Percent Bad Sector 0 00MB 0 00MB 0 00MB 0 00 0 00 Save Reset Overwrite Click checkbox to overwrite the storage d
64. te from the normal condition to this boosted level for the duration of the event Check the box to enable the Function Record When the VK2 1080MD37W detects an event it can record video stream in the Micro SD Memory not supplied or NAS Network Attached Device as a storage device Check the box to enable the Function VK2 1080MD37W User manual V1 0 46 3 5 5 System 1 Information You can enter the system information This page is very useful when you refer device information after installation System E Basic Configuration Information EB Live View Device Name Configuration EB Video amp Image Device name H 264 Mini Dome amp Event System Location Configuration Information Location1 Security Location2 Date amp Time Locations Net k 4 es Location4 Language Maint aintenance Se Reset Support B About e Device Name Configuration Enter the device name e Location Configuration Enter the location information You can enter that by four VK2 1080MD37W User manual V1 0 47 2 Security vV Users System E Basic Configuration B Live View Video amp Image B Event System Information Security Users HTTPS IP Filtering Date amp Time Network Language Maintenance Support B About Security Users User Setting Y Enable anonymous viewer login User List Setting User Name User Group Authority admin administrator live setup system Ce ee oe
65. the translation of host names to IP addresses on your network Obtain DNS Server via DHCP Automatically use the DNS server settings provided by the DHCP server Click the View button to see the current settings Use the following DNS server address to enter the desired DNS server by specifying the following Domain name enter the domain s to search for the host name used by the Network Camera Multiple domains can be separated by semicolons The host name isalways the first part of a Fully Qualified Domain Name for example my server is the host name in the Fully Qualified Domain Name myserver mycompany com where mycompany com is the Domain name DNS servers enter the IP addresses of the primary and secondary DNS servers e Host Name Configuration Host Name enter the host name to be used as device information in the client software or Speco Manager e Services HTTP port Enter a port to receive a service through the HTTP Default Port Number is 80 HTTPS port Enter a port to receive a service through the HI TPS Default Port Number is 443 RTSP port Enter a port to receive a service through the RTSP Default Port Number is B54 s ARP Ping Setting Enable ARP Ping setting of IP address The IP address can be set using the ARP Ping method which associates the unit s MAC address with an IP address Check this box to enable the service Leave disabled to prevent unintentional resetting of the I
66. tic IP is determined by your configuration on the VK2 1080MD37W via the web based configuration of firmware The camera s default is DHCP i L k L f N ye pA P J WIPS Button WPS Button Wireless AP Dome Camera Notes 1 WPS may not work if your AP is configured with a hidden SSID 2 lf any WPS enabled AP is not detected the camera will search APs for 60 seconds after pressing the WPS button and if the camera still can not detect an AP after 1 minute the wireless setup will be cancelled 3 If a camera is assigned with a fixed IP outside the AP s network segment wireless setup will fail 4 Awired connection always has a higher priority and hence wireless setup will not take effect when the RJ45 LAN port is connected VK2 1080MD37W User manual V1 0 12 2 2 Network Connection and IP assignment The VK2 1080MD37W supports the operation through the network When a camera is first connected to the network it has no IP address So it is necessary to allocate an IP address to the device with the Smart Manager utility on the CD Default IP 192 168 30 220 1 Connect the VK2 1080MD37W device to the network and power up 2 Start SmartManager utility Start gt All programs gt SmartManager gt SmartManager the main window will be displayed after a short while any network devices connected to the network will be displayed in the list SmartManager T an oe i File View Help C IP Filter
67. tings Operators have no access to System Options 7 An administrator has unrestricted access to the Setup tools and Administrator l can determine the registration of all other users e Enable anonymous viewer login Check the box to use the webcasting features Refer to 3 5 2 Video amp Image for more details VK2 1080MD37W User manual V1 0 19 2 Network The VK2 1080MD37W supports both IP version 4 and IP version 6 Both versions may be enabled simultaneously and at least one version must always be enabled When using IPv4 the IP address for the VK2 1080MD37W can be set automatically via DHCP or a static IP address can be set manually If IPv6 is enabled the VK2 1080MD37W receive an IP address according to the configuration in the network router There is also the option of using the Internet Dynamic DNS Service For more information on setting the Network please see Setup gt System gt Security gt Network Basic Configuration Basic Configuration Network Users IP Address Configuration Network Video amp Image 7 Obtain IP address via DHCP S wi L Date amp Time Use the following IP address IP address 192 168 30 224 S S H C T E o l 7 R 168 30 1 E Video amp Image Default router 192 168 30 N B Event Save Reset 6 System a About Obtain IP address via DHCP Dynamic Host Configuration Protocol DHCP is a protocol that lets network administrators centrally manag
68. to the list are set as allowed or denied addresses All other IP addresses not in this list will then be allowed or denied access accordingly that is if the addresses in the list are allowed then all others are denied access and vice versa See also the online help for more information Note that users from IP addresses that will be allowed must also be registered with the appropriate access rights Guest Operator or Administrator This is done from Setup gt System gt Security gt Users VK2 1080MD37W User manual V1 0 50 3 Date amp Time System amp Basic Configuration E Live View E Video amp Image amp Event System Information Security Date amp Time Network Language Maintenance Support amp About Current Server Time Date amp Time Current Server Time Date 2013 05 15 Time New Server Time Time zone 20 40 40 GMT Greenwich Mean Time Dublin Edinburgh Lisbon London E Automatically adjusts for daylight saving time changes Time mode 9 Synchronize with computer time Date Time Synchronize with NTP server NTP server time nist gov Set manually Date 2013 05 15 Time Date amp Time Format Date Format YYYY MM DD Time Format 24 Hour Save NTP Interval 12 Le hour 20 40 37 S E Reset It displays the current date and time 24h clock The time can be displayed in 12h clock format in the overlay see below New Se
69. uct may cause radio interference in which case the user may be required to take adequate measures VK2 1080MD37W User manual V1 0 4 THIS DIGITAL EQUIPMENT FULFILLS THE REQUIREMENTS FOR RF EMISSION ACCORDING TO THE CLASS B LIMIT OF EN 55022 THIS PRODUCT FULFILLS THE REQUIREMENTS FOR IMMUNITY ACCORDING TO EN 55024 OFFICE AND COMMERCIAL ENVIRONMENTS TO COMPLY WITH RF EXPOSURE COMPLIANCE REQUIREMENTS THE ANTENNA USED FOR THIS TRANSMITTER MUST BE INSTALLED TO PROVIDE A SEPARATION DISTANCE OF AT LEAST 20cm 7 9in FROM ALL PERSONS AND MUST NOT BE CO LOCATED OR OPERATING IN CONJUNCTION WITH ANY OTHER ANTENNA OR TRANSMITTER CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS VK2 1080MD37W User manual V1 0 5 IMPORTANT SAFETY INSTRUCTIONS ey Ae T 10 11 12 13 14 15 16 17 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type
70. vibration Unplug the unit from the wall outlet if it is not going to The unit is not designed to be waterproof be used for several days or more To disconnect the Exposure to rain or water may damage the unit cord pull it out by the plug Never pull the cord itself Allow adequate air circulation to prevent internal heat Cleaning a a build up Do not place the unit on surfaces rugs blankets etc or near materials curtains draperies Clean the unit with a slightly damp soft cloth that may block the ventilation holes Use a mild household detergent Never use strong solvents such as thinner or benzene as they might Height and vertical linearity controls located at the rear damage the finish of the unit panel are for special adjustments by qualified personnel only E Retain the original carton and packing materials for safe transport of this unit in the future VK2 1080MD37W User manual V1 0 3 CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT TO COMPLY WITH RF EXPOSURE COMPLIANCE REQUIREMENTS THE ANTENNA USED FOR THIS TRANSMITTER MUST BE INSTALLED TO PROVIDE A SEPARATION DISTANCE OF AT LEAST 20cm 7 9in FROM ALL PERSONS AND MUST NOT BE CO LOCATED OR OPERATING IN CONJUNCTION WITH ANY OTHER ANTENNA OR TRANSMITTER CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this prod
71. video services video from customer IP cameras or webcams is transmitted to the service provider s secure cloud infrastructure System B Basic Configuration Network VSAAS EB Live View VSAAS Configuration B Video amp Image E Enable VSAAS B Event VSAAS server URL B System Port Information A Save Reset Security Date amp Time Network Basic DDNS RTP UPnP QoS NAT Zeroconf Bonjour VSAAS Wireless Language Maintenance Support E About e VSAAS Configuration VSAAS Server URL Enter the third party servers URL that uncovers external and internal address information Port Enter the port number used by the VSAAS server The default is 80 Note Video Surveillance as a Service VSaaS refers to hosted Internet recording of security camera video VSaaS takes video monitoring into the cloud Sometimes referred to as hosted or managed video services video from customer IP cameras or webcams Is transmitted to the service provider s secure cloud infrastructure VK2 1080MD37W User manual V1 0 61 YV Wireless Wireless settings must be the same as the access point or ad hoc device When changing the settings they should always be made first in the camera and then in the wireless access point This ensures that the camera is always accessible when making changes System B Basic Configuration Network Wireless B Live View IP Address Configuration E Video amp Image l Obtain IP

VK2-1080MD37W User manual

Contents

Download Pdf Manuals

Related Search

Related Contents