User's Manual
Contents
1. Fast Ethernet media converters 10Base T 100Base TX to 100Base FX series User s Manual FCC Warning Table of contents This device has been tested and found to comply with limits for a Class A digital device pursuant to Part 2 and Chapter 1 UT ENS MR Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful Introduction x M 4 interference when the equipment is operated in a commercial environment This equipment generates uses Product Features 4 and radiates radio frequency energy and if not installed and used in accordance with the user s manual may Technical ificati 4 cause interference in which case user will be required to correct the interference at his own expense echnical Specifications De E x NOTICE Chapter 2 n 1 The changes or modifications not expressively approved by the party responsible for compliance could Package contents T 5 void the user s authority to operate the equipment MERC FARM Paten 2 Shielded interface cables and AC power cord if any must be used in order to comply with the Model information 5 emission limits Chapter 3 MS ET Installation ctum geg BI LED indicato T CISPR A COMPLIANCE The is 7 Chapter 4 v 8 This device complies with EMC directive of the European Community and meets or exceeds the following Applicatio2. optic cable LED indicator supports Multiple fiber connector supports SC ST MT RJ LC etc Supports fault propagation Can be installed on media converter chassis Technical Specifications 3 Standards IEEE 802 3u 10Base T 100Base TX and 100Base FX Media support TOBASE T EIA TIA 568 Cat3 4 5 5e or 6 UTP STP 100Base TX EIA TIA 568 Cat5 5e or 6 UTP STP 100Base FX Multi mode 50 125 um amp 62 5 125 um MMF 100Base FX Single mode 9 125 um SMF 5 Distances support Twisted pair STP 120 meters 393ft Multi mode fiber 415 meters for half duplex Multi mode fiber 5km for full duplex Single mode fiber 415 meters for half duplex Single mode fiber 60km for full duplex gt Wavelength 1310nm on Single Multi mode Data Transfer Rate 100Mbps 10Mbps gt LED indicators System power Twisted pair port Link Activity Speed and FDX Col Fiber port Link Activity amp FDX LEDs Temperature 10C to45C Operating 20C to90C Storage Humidity 10 to 90 Non condensing gt Power consumption 3 4 Watts max Power Requirement 5VDC 1A Certifications FCC Class A CE Mark Dimensions 102 mm 74 mm x 22 mm L x W x H Weight 230g No power adapter Chapter 2 Package contents Before you start to install the Switch please verify your package that contains the following items E One media converter B One Power Adapter E One User s Manual od Model informatio
3. 40 or 60km for SMF 9 125um optic cables on AC frequency range from 47Hz to 63Hz TUV CE UL Safety full duplex operation B Power adapter DC output is 5VDC 1 5A FW 100Base FX fiber port LC type SMF E The device DC input 5VDC 1A Single mode LC e Up to 20 40 or 60km for SMF 9 125um optic cables on Il The TP port full duplex operation The device TP port support Auto MDIX Auto negotiation and Flow control functions The cable length up lo 100 meters for shielded unshielded twisted pair cable Allow users connect the converter to 10BASE T and 100BASE TX devices Ill The Fiber port The converter provided different types of fiber connectors such as SC ST MT RJ and LC for multi mode or single mode fiber cables Full Duplex or Half Duplex operation on fiber port The converter provided slide switch at right side of converter The purpose of the slide switch is for fiber full duplex or half duplex operation The factory default is full duplex as below chart e Bee i A E ove The LED indicators LED Color Status Description Power Yellow On Power on FDX Green On Ful duplex Off Half duplex Flashing Partial collision occurs 10 100M Green On Port is on the 100M status om Port is on the 10M status LINK ACT Yellow On 10 100Mbps port for connection Flashing 10 100Mbps for data activating Chapter 4 Application Multi Mode Fiber MMF appli
4. cation 10 100M Switch 10 100M Converter 10 100M Converter 10 100M Switch MMF Up to 5 km Cm mam x t 10 100M Switch witch Fiber Module 1Q 100M Converter 10 100M Switch Single Mode Fiber application SMF Support 10 20 40 and 60 km d S 10 100M Switch 10 100M Converter 10 100M Converter 10 100M Switch
5. n 100Base FX Multi Mode 1310nm wavelength Model Description E 100Base FX fiber port SC type MMF B Up to 415 meters 1360 ft for MMF 50 125um or 62 5 125um optic cables on half duplex operation Up to 2 Skm 1 24 3 1 mi for MMF 50 125um or 62 5 125um optic cables on full duplex operation 100Base FX fiber port ST type MMF B Up to 415 meters 1360 ft for MMF 50 125um or 62 5 125um optic cables on half duplex operation E Up to 2 5km 1 24 3 1 mi for MMF 50 125um or 62 5 125um optic cables on full duplex operation E 100Base FX fiber port MT RJ type MMF Up to 415 meters 1360 ft for MMF 50 125um or 62 5 125um optic cables on half duplex operation Up to 2km 1 24 mi for MMF 50 125um or 62 5 125um optic cables on full duplex operation E 100Base FX fiber port LC type MMF E Up to 415 meters 1360 ft for MMF 50 125um or 62 5 125um optic cables on half duplex operation B Up to 5km 3 1 mi for MMF 50 125um or 62 5 125um optic cables on full duplex operation Multimode SC Connector Multimode ST Connector Multimode MT RJ Connector Multimode LC type Connector Chapter 3 100Base FX Single Mode 1310nm wavelength Installation Model Description L DC input amp external power adapter E 100Base FX fiber port SC type SMF The external power supply adapter specification Single mode SC E AC input range from 90VAC to 260VAC connector E Up to 10 20
6. n M eegen B technical standard EN 55022 Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment This device complies with CISPR Class A WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user many be required to take adequate measures Chapter 1 Introduction The Fast Ethernet media converters series are designed to bridge a 100Base TX signal to a 100Base FX signal It s used to extend the connection distance between two Fast Ethernet Twisted pair devices via fiber cable transparently with no performance degradation The converter series is base on switching hub design It s supported Auto negotiation amp flow control function on Twisted pair port And provided different types of fiber connectors such as SC ST MT RJ and LC for multi mode or single mode cables Product Features Complies with IEEE802 3u 10Base T 100Base TX 100Base FX Standards TP port support Auto MDIX A Auto negotiation TP port up to 100 meters for shielded unshielded twisted pair cable Supports Full duplex amp Half duplex operation on TP base on Auto negotiation Switch base design support flow control capability Supports Full duplex amp Half duplex operation on fiber by slide switch 100Base FX interface for up to 5km Use 50 125 um or 62 5 125 ym MMF optic cable 100Base FX interface for up to 60 km Single mode 9 125 um SMF
Download Pdf Manuals
Related Search