Global Door Controls TH1100EDTBARFAL Installation Guide
Contents
1. INSTALLATION INSTRUCTION FOR ST EDTBAR F 41100 SERIES FIRE EXIT DEVICE END CAP SURFACE OF DOOR FOR AS ap BEFORE INSTALLING DEVICE PLEASE CHECK EXIT DEVICE APPLIED MUST Sy a 1 IF DOOR FITTED AND HUNG dpi E aa 5 2 SIZE OF EXIT DEVICE FUNCTION AND DESIGN pa 21 36 DOORS CAN BE CUT TO FIT DOORS DOWN TO 30 WIDE ES pa 22 48 DOORS CAN BE CUT TO FIT DOORS DOWN TO 36 WIDE Pp e 23 HAND OF DEVICE AGAINST APPLICATION AA RAK MOUNTING d BRACKET RIGHT HAND REVERSE BEVEL LEFT HAND REVERSE BEVEL SLIDING SHIM CHASIS ASSEMBLY 2 3 INSTALL LEVER OR KNOB OR PULL TRIM LEVER TRIM ATTACH OUTSIDE PULL TRIM l IF USED La Az PA SK ALS E CHASIS A N s t MF WO TRIM ATTACH CHASIS S 3 TTV WITH 4 210 WOOD OR CHASIS E A NS i AE MACHINE SCREW ga 24 i F HEAD COVER KNOB TRIM ES ido A m 2 d Y Kr e TAN AA i mg t AA gt AR BRAGKET SCREWS VE i t F L Yo AT12 00 eg t TYPE OF INSTALLATION SS ES A POSITION j ps E DOUBLE DOOR DOUBLE DOOR WITH A 2 l SINGLE DOOR PLUNGER i se SP i S WITH MULLION NO MULLION S N CHASIS MOUNTING SCREWS 3 APPLY RAIL ASSEMBLE 1 CHECK THE SIZE OF DEVICE IF CUTTING TO LENGTH IS REQUIRED 2 DETERTMINE CUT OFF LENGTH X BY SUBTRACTING 1 3 4 FROM Y MARK CUT OFF POINT ON MOUNTING RAIL 2 APPLY HARDWARE 3 DEPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO CHASIS LEVEL RAIL AND FASTEN CHASIS AND MOUNTING 21 DRILL HOLES PLATE2. 2 1 8 DIA HOLE WHEN PULL IRIM IS USED ROD CENTERLINE D FOR REFERENCE LINES REFER TO INSTRUCTION SHEET I FC 5000 PH 26
3. i MARK DOOR FAGE AND DRILL FOR DOOR VISTILE ST id CUT OFF MUST LEAVE VERTICAL WI MIN OVERLAP CHASIS WITH RAIL HOLES IN ACCORDANCE WITH THE DIAMETERS SUGGESTED SEE ATTACHED TEMPLATE OUTSIDE mal C At ETE DONT CUT CLOSER THAN Et 1394 FROM LOWER PIVOT L t TIGHT AGAINST RAIL ko Ss q 2548 i Eg SE a A O E E ES boi 11 18 dej Var ASSY Er 4 2 MOUNTHU PLATE SCREWS INSIDE CENTER OF CYLINDER END OF BODY kd G ERE OUTSIDE FACE OF THE DOOR INSIDE FACE OF THE DOOR HEAD MACHINE pe 13 ROUND HEAD 22 INSTALL CYLINDER 4 INSERT THE CYLINDER THROUGH CYL 4 APPLY COVER AND STRIKES RING THE HOLE ON THE DOOR OUTSIDE FACE OF THE 2 KEEP THE TAR PIECE HORIZONTAL i ER 3 MOUNT LINEER ON INSIDE OF DOOR AND HR am dag coo ts 4 TAILPIECE PROJECTION OVER INSIDE OF By A z po SS S ESA DOOR IS SUGGESTED IN THE RANGE AA KA s nd 9 I die DE 9 32 15 32 IF NECESSARY USEA S T l JE a PLIER TO BEND AND CUT TO DESIRED i C T S PN KN umer LENGTH IL 2 le pe a ar PS L a TE e 11 Mo T HNSTALLTION da 9 32 15 32 S dv E eN q SCREW CyL RING HID 24 1 medl ATTACH COVER TO CHASIS WITH ATTACH END CAP TO MOUNTING ATTACH STRIKE TO DOOR STOP H 144 t TRUSS HEAD MACHINE PLATE WITH L COVER SCASVWS WITH 2 STRESE SCREW AND LOCK JE TAILPIECE PROJECTION Nn WOE ROOG 7 FOR EDTBAR AND SVRTBAR SERIES EXIT DEVICE USING LEVER HANDLE TRIM FOR WOOD DOORS DRILL 4 3 32 DIA X 15
4. 114 DEEP PILOT HOLES FOR METAL DOORS TAPPED 4 43 16 HOLES FOR LEFT HAND CS HAND 4 tt met FOLD AND ALIGN TEMPLATE ON EDGE OF DOOR AA A maan annee mmm mamenn E a m FINISHED FLOOR CENTER LINE OF PUSH RAIL 2 J 8 DIA NT THRU DOOR OR O E R 7 8 N 5 16 DIA 2 1 2 DEEP 41 FROM i i CENTERLINE D FOR REFERENCE q REFER TO INSTRUCTION SHEET FC 5000 PH 26 I FOR EDTBAR AND SVRTBAR SERIES EXIT DEVICE USING LEVER HANDLE TRIM OR ON TRIMS DRILL 4 3 8 THRU BOLT HOLES i i FOR LEFT HAND N A HAND THRU BOLT RE 2 5 8 BACKSET FOR RIGHT 2 1 8 DIA THRU DOOR EG 5 16 DIA 2 1 2 DEEP FOLD AND ALIGN TEMPLATE ON EDGE OF DOOR e FINISHED FLOOR CENTER LINE OF PUSH RAIL VERTICAL REFERENCE LINE FOR REFERENCE LINES REFER TO INSTRUCTION SHEET 41 FROM FC 8000 PH 26A FOR EDTBAR AND SVRTBAR SERIES EXIT DEVICE USIMG LEVER HANDLE TRIM VOR WOOD DOORS FOR THRU BOLTING DEEP PILOT HOLES THRU DOOR FOR METAL DOORS TAPPED 4 43 16 HOLES FOR LEFT FOR RIGHT HAND HAND EP L s y PSR Q ES EN E a FI mg T T ya EEE dy SI 1 a E p z Ms A gt l 41 FROM TI 1 114 DIA HOLE WHEN FINISHED FLOOR IE EG CENTER LINE ISUSED OF PUSH RAIL Q LESS OUTSIDE TRIM O AN anr TT LC A N S L DOOR ke PREPARATION 161 CUT OUT OF
Download Pdf Manuals
Related Search