Barclay Products TKADTR60-WBN3 Installation Guide
Contents
1. For wall mounting of the diverter to a house water supply line see your local plumber NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish 3 20 09 P 847 244 1234 www barclayproducts com Water Supply Hookup Kit Cat No Z gt for Tub with Legs 99 6 BARCLAY INSTALLATION INSTRUCTIONS Parts Included e 4 Cone Washers A 2 Decorative Locknuts B Left Supply Tube C e Right Supply Tube D 2 Escutcheons E 2 Locknuts F Tools Needed e Adjustable Wrench Set of Crescent Wrenches Pliers Teflon Tape use as a sealant on all male threaded tubing This water supply tube kit includes the parts listed above ONLY The faucet in your bathtub should be purchased previously and separate from this kit y To Assemble Tubes W in KE 1 First be sure to shut off the the water supply Remove old water supply tubing Put a cone washer A with the wide end of the washer inward onto the upper end of the left supply tube C 2 Slide a decorative locknut B up to the top of the left supply tube C and put on a cone washer A 3 On the bottom of the left supply tube C slide one of the escutcheons E up the tube partway then slide the loc2. LA Acrylic Claw Foot Tub BARCLAY INSTALLATION INSTRUCTIONS Tools Needed e Wrench or socket Drill amp Bits Parts Recommended e 2 2 x12 boards 4 Lag Bolts 4 Flat Washers Be sure to re inforce the floor before securing tub We recommend 2 2 x12 s securely fastened to floor beams where you plan to secure your tub Anchor Tub to Floor 1 Place tub in intended position on floor 2 Mark foot anchoring locations on floor with pencil 3 Move tub to the side to allow work space 4 Drill starter holes in floor 5 Put tub back into position 6 Place flat washers on lag bolts N Put lag bolts through slot in bottom of foot and screw into floor using wrench or socket 9 7 10 P 847 244 1234 www barclayproducts com Old Style Spigot Cat No gt INSTALLATION INSTRUCTIONS Parts Included e 1 Valve Body 2 Large Locknuts 2 Cross Handles Attached Tools Needed e Adjustable Wrench Slip Joint Pliers Pipe Putty or Teflon Pipe Tape NOTE Handles are identified HOT and COLD The hot handle must be to the left and cold to the right 1 Align the valve assembly with the holes in the tub 2 Apply teflon tape to both ends of the hot and cold supply nipples On the outside of the tub thread the large locknuts onto the other ends of the nipples and secure the unit to the tub Tighten with a wrench or pliers 3 Connect the water supply nipples to the water supply tubes
3. knut F up the end of the tube C directly under the escutcheon 4 Put another cone washer A with the wide end of the washer upward onto the bottom end of the tube C 5 Repeat steps 1 4 using the right supply tube D To Install Tubes 1 Attach the bottom end of the left supply tube C to the water supply tubing in your floor by screwing the locknut F down tightly Let the escutcheon E slide down to the floor 2 Attach the upper end of the left supply tube C to the cold side faucet supply tube located on the rear of your tub by inserting the supply tube C into the faucet supply tube and tightly screw the decorative locknut B over the two for a tight fit 3 Repeat steps 1 2 using the right supply tube D and connecting it to the hot side faucet supply tube NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish 10 30 07 P 847 244 1234 www barclayproducts com Leg Tub Cat No 4 Drain 9999 BARCLAY INSTALLATION INSTRUCTIONS Parts Included e Top Overflow Tube 1 Bottom Shoe 2 Top Waste Flange 3 Face Plate 4 Exposed Tee 5 e Face Sponge Gasket 6 e Waste Gasket 7 Lift Stop 8 2 1 1 2 Nut and Washers 9 Face P
4. late Screw 10 1 1 2 x 6 Tube 11 1 1 2 O D Escutcheon 12 Tools Needed e Wrench Pliers Teflon Tape use as a sealant on all male threaded tubing Tube Cutter Plumbers Putty To Assemble Tubes 1 Assembled 3 and 8 screw into 2 7 is on top of 2 beneath the tub Place a bead of plumbers putty around bottom of 3 to seal to tub and protect from leaks Then tighten 3 into 2 2 Assemble overflow Follow diagram 3 Set 1 in place 4 Place Tee 5 on shoe Cleaning Instructions 5 Trim bottom of tube 1 to fit into Tee 5 Wipe this whole set off with warm water and a 6 Trim tube 11 to fit soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the 7 Tighten the nuts protective lacquer coating and leave the brass exposed causing it to tarnish NOTE Please seek professional help if you have copper plumbing in your home 1 8 08 P 847 244 1234 www barclayproducts com
Download Pdf Manuals
Related Search