Whitehaus Collection WHMFL3222-EB Installation Guide
Contents
1. to the installation instruction then coat with a layer of silicone between the toilet and floor Note Do not use the product immediately after completion of installation Make sure there is no water around the product for 24 hours2. Troubleshooting Malfunctions Reasons Solution 1 The main water valve does not open 1 Turn on the valve 2 Incoming water filter net is clogged 2 Clean the net 3 Floating ball of water inlet valve in cistern 3 Readjust the floating ball does not work e No Incoming Water 1 Higher water pressure 1 Reduce water pressure 2 Floating ball of water inlet valve does 2 Readjust the floating ball not work 3 Call your dealer to replace Non Stop Incoming Water 3 Water inlet valve is broken inlet valve 4 Floating ball of water inlet valve touches 4 Adjust the direction of the inwall of cistern floating ball 1 The water level of inlet valve is too low 2 The push button does not reach pushing point 3 Press the wrong button Adjust the water inlet valve to appropriate position Adjust water level rod Identify small and large flushing button or call your dealer Inadequate Flushing Water 1 The drainage outlet is not aligned with the 1 Readjust or reinstall the outside drainage pipe product 2 Drainage pipes are obstructed 2 Clean the drainage pipes 3 Inadequate flushing water 3 Adjust the water in cistern e Slow Drainage or Inadequate Suction Fasten the nuts Change the water supply spacers 1 The hexangular nuts of water inlet valve are not fastened 2 The water supply spacer of inlet valve is damaged 3 The water supply spacer on the bottom of cistern is damaged 1 Drainage pipe
3. ion position is aligned with that of the toilet Check all the specifications of the pipelines for the water supply Handle product with care and ensure that the nut is not overtightened When installing the toilet make sure the floor is even If you want to replace the toilet turn off the water supply and flush the toilet to make sure no water remains inside the toilet Remove the soft pipe for water supply and unfasten the screws Remove the toilet and the old gasket and clean the end of the drainage outlet Note Plug the drainage outlet on the floor if you do not install the toilet immediately Make sure the water supply is turned off NOTE 1 We reserve the right to change the features packing and fittings of the product without notice 2 Please keep the installation instructions accessible including installation procedure fitting form troubleshooting and notice 3 Closet flange is not included Common Tools Needed e 11 64 Drill Bit for Wood Floor Installation e 5 16 Drill Bit for Concrete Tile Installation e Adjustable Wrench e Pipe Wrench e Tape Measure e Drill e Silicone Installation Procedure 1 Install Flange and Water Supply Valve 1 Install the water supply valve onto the installation position according to the dimensions of the product 2 Align the flange with the drainage outlet 3 Mark the installation positions for screws and drill holes 4 Fix the flange onto the floor Wate
4. r supply valve ETAR ETD ji Flange N 9 CUE D CUED CE 2 Mark Installation Holes 1 Mark the center line for the drainage outlet 2 Mark the installation position for the mounting screws and connecting pipe as illustrated below drawing for distance between installation holes 7M Finished Wall Installing position for 7 plastic le 27 Please according lo the actual distance of product a e mm e er m oae oe Po Center Line 3309 EB L 6 M 77 3222 EB L 67 M 7 3351 EB L 5 M 8 3 Install T Screw Mounting Screw and Connect Pipe 1 Drill holes onto installation position and insert expandable plastics 2 Make the bottom of connecting pipe face upward then cover the flange onto the water outlet tightly Make sure the pipe is not plugged 3 Get two T screws through the installation holes of the connecting pipe Adjust the screws to get the four holes on the back side of the connecting pipe aligned with the expandable plastics on the floor Fix the connecting pipe and 7 plastic onto the floor as illustrated iir Eir a T E Installing Hole for Expandable Plastic 1 4 Pcs 5 height of 1 Installing Hole for Expandable Plastic 2 2 Pcs 10 height of 2 Expandable Plastic 7 plastic S Expandable Plastic 2 4 Install Toilet 1 Pick up the toilet and make sure the two pieces of mounting screws are fully through the installing holes of
5. s are obstructed 1 Clean the drainage pipes Overflow From Drainage Pipe 2 Water outlet pipes are obstructed 2 Clean the water outlet pipes Note 1 Do not throw newspaper diapers sanitary napkins or similar articles in the toilet bowl 2 Do not impact the ceramic part heavily in case of any damage 3 To maintain the normal flushing function of the toilet please use a long handle nylon brush and a neutral cleanser to clean up the bowl or pipes to prevent the accumulation of mineral substances It is suggested to clean your toilet once a week 4 Clean the filter at least once a month to prevent slow water inletting or water blockage in the tank 5 Do not use any cleanser in the tank otherwise the rubber accessories in the tank may be damaged causing leakage e Leakage Please follow what is specified below to avoid discoloration deformation fine cracks or scratches on the toilet seat 1 Do not expose the toilet seat to sunlight or sources of heat 2 Do not use sharp or abrasive materials to clean the toilet seat 3 Do not use corrosive chemicals to clean the toilet seat Whitehaus Magic Flush Product Installation Manual WHMFL3309 EB WHMFL3222 EB WHMFL3351 EB Before Installing O1 T Read the instructions carefully to be familiar with the tools fittings and installation procedures to prevent any unnecessary damage Inspect product prior to installation Check whether the rough in on the installat
6. the toilet 2 Align the center of the toilet with the center line on the floor and then gently place toilet down Note Make sure pipe has gone through the four layers of sealing rubber spacer of the connecting pipe after installing the toilet If it is not fully through it will have a bad effect for flushing function Center Line Sealing rubber spacer fem pip 4 con t Install Toilet 3 Place the toilet on the floor with screws and plastic covers then cover the decoration caps Decoration cap Plastic cover 5 Connect Water Supply and Check Sealing Performance 1 Get the water supply valve and the water inlet with supply connecting pipe if the fitting is separated _ Product 7 plastic from the filter connect the filter first 2 Turn on the water supply valve and make sure there is no leakage on any joint Fastening the nuts can prevent leakage Cistersn _ Water inlet Waterproof spacer 5 Filter E A Waterproof spacer R Nut Soft pipe Nut Waterproof spacer Water supply valve eo a KO 6 Check Water Refill Pipe 1 Open the cistern cover and make sure the overflow pipe is inserted into the water refilling pipe Note If the water refilling pipe does not insert into the overflow pipe the flushing water will be inadequate Water refilling pipe Overflow pipe 7 Install Toilet Seat 1 Install the toilet seat according
Download Pdf Manuals
Related Search