Worldwide Lighting W33519C20 Instructions / Assembly
Contents
1. W 33519C20 L20 W20 H5 5 L12 We are dedicated to providing the finest quality of crystal chandeliers for our customers Our master craftsman and designers pay their full attention to detail prompt and efficient service Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions thoroughly If you have any questions please feel free to call our toll free chandelier hotline at 1 859 411 8999 C US Crystal Dressing Instructions When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals xX 80holes 22 square shaped crystal with 2 holes 80holes clipt t22 square shaped crystal with 2 holes 1 22x63 block 144holes 40 bal1 CANOPY PARTS LIST Existing Electrical Box Crossbar Crossbar Screws x 2 not srpplied Wire Connector Shrinkable tube Cable tie Ground Wire INSTALLATION DIAGRAM CANOPY Parts List z 03 Metal Finial 01 Crossbar 02 Lamp Body WARNING Crystal Dressing Diagram CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and installing When dressing the chandelier WARNING with the crystals please remember to wear either rubber or cotton i gloves So as to prevent any After passing the ma2. ectly screw the connect point with the junction cap 3 Make sure the main wire is enough long and keep the rest wire in the 4 j box 4 Screw the lamp body 02 on Crossbar 01 With Crossbar Bracket 5 As the crystal pressing instruction hang the crystal parts The end
3. ghting is not responsible for unprofessional wiring Frame Assembly Diagragram CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefuly Before you proceed to install make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order A Existing Electrical Box B Crossbar C Crossbar Screws D Metal Plate E Crossbar Bracket F Neutral Conductor G Hot Wire H Junction Caps I Ground Wire Attach the Crossbar B to the existing electrical box A using the two crossbar screws E which are not supplied and should already be in your box I AN AN ARN aN AN 2 AAVA A A f A NAAN 4 4 y 7 N 7 N AVAN 7i WY VY COW ys Ney WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and WARNING After passing the main electrical wire through the 10mm pipe and connecting the pipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts installing CAUTION Rated 110v 130v 60Hz bulb E12 40W maximum Take care to avoid damage to the surface of lighting and wire Wearing gloves is recommended when installing Connect black or red wire of the lig
4. hting to the white or blue wire Then connect to the neutral wire and double colored or bare copper wire to the ground wire Never install lighting on damp ceiling The room should be dry and well ventilated Keep lighting away from acid alkali and other corrosive chemical or gas Clean with soft cloth only Installation must be carried out by qualified electrician only Disconnect the power before installing cleaning or replacing the lamp Never cover the lighting when power is connected Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts Take care to avoid damage when installing glass parts All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrical codes Make sure that the electrical supply to the chandelier is turned off at the main fuse or circuit breaker before doing any installation Worldwide 7 is not responsible for unprofessional wiring Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order 1 Affix the crossbar 01 on junction box 2 Make sure the positive and negative charges of wire and lamp body match corr
5. in electrical wire through the 10mm pipe and datage or smudging on the crystals connecting the pipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts CAUTION Rated 110v 130v 60Hz bulb E12 40W maximum Take care to avoid damage to the surface of lighting and wire Wearing gloves is recommended when installing Connect black or red wire of the lighting to the white or blue wire Then connect to the neutral wire and double colored or bare copper wire to the ground wire Never install lighting on damp ceiling The room should be dry and well ventilated Keep lighting away from acid alkali and other corrosive chemical or gas Clean with soft cloth only Installation must be carried out by qualified electrician only Disconnect the power before installing cleaning or replacing the lamp Never cover the lighting when power is connected Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts Take care to avoid damage when installing glass parts All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrical codes Make sure that the electrical supply to the chandelier is turned off at the main fuse or circuit breaker before doing any installation Worldwide li
Download Pdf Manuals
Related Search