Sandusky RTA-7001-07 Instructions / Assembly
Contents
1. Left Back Panel When lifting position both hands near the center of the Back Panel as shown to avoid bending it o Insert the tabs into the matching holes Step 2 Side Assembly A While the Back Panels are still lying on a i Lift the edge of Back Panels flat surface lift the outside edge of the and set them over the Sides Right Back Panel D and slide the L shaped inserting the tabs through the bend of the Right Side Panel B under it matching square holes IMPORTANT Make sure the bends on the Side Panels are on the same side B Insert the tabs on the Right Back Panel B into the matching square holes in the Right Back Panel D Square Holes Tmt Right Back Panel D C Once all the tabs are started slide the Side and Back Panels in opposite directions to fully engage the tabs Left Back Panel C D Tap each of the tabs down with a rubber mallet to lal tighten the connections Square Holes n on Back Panels E Repeatthe steps with the Left Side Panel A Tabs on Side Panels Left Side Panel A shown transparent Slide the panels to fully engage the tabs and tap them down Quick Assembly Storage Cabinets Page 3 Step 3 Bottom Assembly The Kick Plate slides into the channel on the Side Panels and locks into place Channel A Position the Kick Plate M as illustrated and begin installation by lifting its right end upwards inside the channel on2. Panels Back Support IMPORTANT The Side and Back Panels must be inside the supports N located under the Top Square Hole Side Support Back Tab Square Hole a Side Tab View under Top showing Side and Back Panel supports and partial engagement Step 5 Shelf Installation A Atthe desired shelf height insert 2 Shelf y Clips K into the holes located inside kr the front edges of the Side Panels Shelf Clip K la B Angle a Shelf J into the cabinet above the installed Clips with its rear tilted down if f lj l i C Insert the rear of the Shelf J into the slots eel a in the Back Panels that are closest in height cout to the installed Shelf Clips Y D Tilt the Shelf J down until it rests on the D Shelf Clips If the Shelf is uneven 2 reposition the Shelf Clips into appropriate SE locations to level it SY E Repeat this process for all of the shelves Snap the botton of the Clip into the hole Channel Insert the Posts into the channel on each of Panels i Tap down the Top evenly until the Tabs lock it in place Insert the rear of the Shelf intothe g of Tilt the front Y of the Shelf down and rest it on the Shelf the Side C jp Lal Lj a CA Ae A Page 4 a Begin lowering the Top by tapping just over the Posts Keep the Top as level as po
3. B Assembly Lei Back Panel C Right Back Panel D Left Door E K ShelfClip L Bottom Notched comers Right Door F TEE 1 1 Top Eee aictamercenice Shelf Clips K 4 S o a ___ Pease call 1 773 475 3000 M Kick Plate Bottom L Please have your model Kick Plate M Pt _ number handy 4 008 1 Quick Assembly Storage Cabinets Assembly Instructions TIPS FOR EASIER ASSEMBLY 2 person assembly is recommended e Assemble the unit on a flat surface Some locking tabs may flatten out or bend open during transport Locking Tab Adjustments can easily be made using a small blade screwdriver with light pressure Can be adjusted open or closed to ease assembly Step 1 Back Assembly Page 2 A Lay the two back panels on a flat Surface Position as illustrated Right Back Panel D Bend is up B Place the Right Back Panel D over the Left Back Panel C inserting the tabs into the matching holes Square Holes C Once all the tabs are started slide the Back Panels in opposite directions to fully engage the tabs Bend is up D Tap the tabs down with a rubber mallet to eee tighten the connections Right Back Panel TZ Slide the panels to fully engage the tabs and tap them down NOTE On the 72 model use care when handling the Back Panels They bend very easily if not handled properly Use 2 hands and NEVER put your fingers in the slots ONN ON ITTTTITIIIITI
4. the Right Side Panel B Kick Plate M Right Side Panel B B Push the Kick Plate upwards until the crescent tab on the Side Panel engages the square hole on the Kick Plate M Note this is a tight fit A loose connection SST AAA A A a would result in an unstable unit C IMPORTANT Bend the tab on the bottom of the Side Panel 45 degrees inward to lock the Kick Plate in place D Repeat the procedure for the left side of the Kick Plate Cresent Tab on Side Panel NOTE Kick Plate fits inside the bend on the Side Panel Lift Kick Plate into the channel until it locks Bend tab J pa 45 degrees lY inward to Kick Plate Hh Tab bent and Kick Plate Square Hole locked in on Kick Plate position Angle the Bottom to engage the supports on the Back and Side Panels Tilt it forward until it s front edge goes OVER the bend on the Kick Plate IMPORTANT Ar The notched corners on the af Bottom L must face the Back Panels ES a GE a Ge en en Ee oe A a A j a mka e The Bottom L must engage eT ee O A the supports located on each ji NG of the Back and Side Panels j j al Support ji i Carefully stand i the unit upright i Tap Bottom down i to fully engage the supports E Install the Bottom L by placing it in the cabinet with the notched corners toward the Back Panels F Angle the Bottom L as illus
5. Required Tools Rubber Mallet Quick Assembly Storage Cabinets smal Screwdriver Model Numbers RTA 7000 RTA 7001 l S mall P hillips Screwdriver Safety Instructions CAUTION Use caution when handling and assembling metal parts Metal may have sharp edges or corners Manufacturer recommends the use of protective gloves when assembling product e This unit should be installed on a level surface Do not use this unitas a step ladder Do not climb on the unit e This unitis not intended to be used in any other manner than for storage Do not exceed the manufacturer s recommended weight capacity of 150 Ibs 68 kg on each shelf Always distribute weight evenly on shelves e The manufacturer recommends the storage of heavier items on bottom shelves All assembly instructions must be followed exactly or the unit may not be assembled correctly and may not be stable Assemble the unit on level surface Parts List Top D Right Back Panel F Right Door Plastic Door Rod Guide Top o Handle Mounting Holes G Door Rods Bottom Plastic Door Rod 7 Guide A Left Side Panel C Left Back Panel E Left Door Bottom Top Please refer to the chart below to confirm that you have the correct number of parts for your product Products are listed by their model number T 3 42 2 Shelf 72 4 Shelf Shelf H Handle ae Left Side Panal A 1 OZ Sid SO Right Side Panel
6. andle mea Lockwasher Screw C Insert the cam through the tear drop opening and place it a onto the square shaft on the back of the Handle H Secure the Handie in the vertical closed D Take one of the Door Rods G and insert the end without the hole Posen into the bottom plastic rod guide on the Door Place the hole in the i alaaa other end of the Rod G on the bottom pin on the cam Repeat the process with the top Door Rod E Attach the holding plate with the counter sunk screw NOTE Tighten the screw securely Ifthe screw comes loose the rods can fall off This may result in a jammed door and potential damage Turn the handle to the open position before closing doors Top Door Rod Cam is through the tear drop opening Pins onCam Cam is on the Square shaft with the pins outward j Pum Door Rag Holding Plate Position cam through the Position the Door Attach the holding tear drop opening on the door Rods through the plate Make sure the and onto the square shaft Pate guides ana screw is tight onto the pins on the cam After assembly is complete MILD SOAP and WATER can be used to clean the unit by wiping with a SOFT CLOTH
7. ssible Back Support The Tabs on the Side and Back Panels lock into the square holes on the Supports Side Support View under Top showing Side and Back Panel tabs fully engaged Reposition the Shelf Clips to level the Shelf if Quick Assembly Storage Cabinets Page 5 Step 6 Door Installation A Select the Right Door F with the handle holes and position the Hinge Pins over the matching hinges on the Right Side Panel NOTE If some of the Hinge Pins were bent during transport bend them back to align them with the Side Hinges Door Hinge Pin The Pins on the Door Hinges slide into the Side Hinges B Once all the Door Hinge Pins are engaged into the holes on the Side Hinges swing the door slightly and apply mild downward pressure until the door is fully seated Handle Holes UU C Repeatthe steps to install the Left Door E Side NOTE the cabinet must be on a level surface for the doors i Hinge to align properly _ __ Left Door E Right Door F Close up of Hinges Step 7 Handle Installation A Remove the 3 screws from the p back of the Handle H b gt hum Lockwasher Screw No 8 32 x 1 4 B Insert the Handle H into the Right E Door F and fasten securely with 2 lock m P 2 Han u washer screws Make sure the Handle is Remove the screws saing counter in the vertical closed position from the H
8. trated and engage the supports located on the two Back Panels Note as with the tabs Some adjustment to the supports on the Side and Back Panels with the screwdriver may be necessary G Gradually tilt the front edge of the Bottom L forward making sure that it engages the supports located on the Right and Left Side Panels and goes over the bend on the front of the Kick Plate M OVER the bend on the Kick Plate i The front edge of the Bottom is H Carefully stand the unit upright and tap the Bottom L down Make sure the Bottom L has full engagement in the supports on the Back and Side Panels The Bottom must fully engage the supports located on the Back and Side Panels Quick Assembly Storage Cabinets Step 4 Top Assembly A Begin inserting the posts on the Top I into the channels on the Right and Left Side Panels Starting with the Top ona Slight angle may help B Once both posts are started Tap evenly down on the Top I until it is just past the Side and Back Panels Make sure the Top I is going OVER the Side and Back Panels C Check under the Top I to make certain that the Side and Back Panels are INSIDE the supports D Tap the Top I down around the edges until the tabs on the Side and Back Panels snap into the square holes on the supports Tap the Top down evenly until it is just past the Side and Back Panels IMPORTANT The Top must be OVER all the Side and Back
Download Pdf Manuals
Related Search