Unique Home Designs 5V0000UNWH00D Installation Guide
Contents
1. NI O Prepare inactive door Remove the mounting screws Lift the top lock up and out of on all three locks of the inactive the edge of the door and un door attach the rod hooked to the rear of the latch assembly Remove the two screws in the Using needle nose pliers grasp mortise gear and center lock the rod assembly through the and pull out the assembly mortise gear in the center lock opening Remove tape and discard throw protectors I out Grab the rod assembly through the top lo2. Use a 1 2 wood chisel or spade drill bit 1 2 to clean the shoot bolt area out to a depth of 1 2 Re install the assembled frame in the opening using temporary screws Do NOT install permanent screws O Attach hinges to doors Place hinge C over pre drilled holes on the door The flat part of the hinge attaches to the door The barrel a Jamb Side A C of the hinge should point F Anti bow point AA always be on the receiving YA outside of the door hole AN Use screws provided off with the hinges and oj O p attach all 3 hinges to Note The Anti bow point receiving eachidoor hole lines up with the pre drilled hole on the door CAUTION Do NOT lay door on it s side so that it rests on the 3 point lock throws This will cause the system to offset and you will need to remove and reset the locking system see step 18 Q Hang door panels Have a helper hold the door in place It is important the door is held in proper alignment so the first mounting A screw in each hinge is d driven straight into the door panel It may help to use blocks or similar props to assist in keeping the door properly aligned Attach all 3 hinges to the frame using two 8x1 flat head screws G in each hinge Add a temporary screw 6x2 temporary drywall screws W in the outside and inside mounting holes at each hinge Page 5 O Remove throw protectors N
3. Care and maintenance Over time airborne dust dirt and impurities can accumulate which will cause visual defects to your Meshtec screen and if not regularly and properly removed can lead to further damage staining and corrosion Your cleaning schedule depends upon your environment ENVIRONMENT DESCRIPTION CLEANING SCHEDULE Inland rural and away from industry and urban activity every 6 months Urban suburban inland and away from heavy industry every 3 months Urban suburban coastal within 25 miles or near heavy industry every 2 4 weeks Thoroughly wash the screen and door frame using a soft cloth mild soap and water Take care to avoid exposing handles main lock and 3 point locks to excessive amounts of water Using a dry soft cloth remove any excess water when done Pay particular attention to drying the screen to frame attachment area fully Avoid using any sharp objects or abrasive materials on the door frame or screen Use white grease to lubricate the hinges at each cleaning Your Unique Home Designs security door with Meshtec Advanced Screen System is warranted against manufacturer defects under normal residential use for the first 10 years you own the product and terminates if you sell or otherwise transfer the product or the property upon which it was installed An additional 5 years warranty protection is awarded for 15 year total warranty when the product is registered on line at uniquehd com registration
4. Hinge side Hinge side jamb jamb Page 3 2 Determine active and inactive doors The active security door should be on the same side as the active primary door on the house Both security doors will be operational The inactive security door however will be held stationary by shoot bolts P at the top and bottom edges of the door The shoot bolts can be retracted to open the inactive door Inactive Door 8 Active Door omo eee Top View S jambs Test fit frame and trim hinge side Place the top header jamb I double door kit package C and hinge side jamb A door j package 1 into position If the hinge side jamb is too long mark with a pencil at the bottom the jamb should sit on top of the threshold Slide weather stripping up just above cut mark and trim jamb to length if necessary O Follow same test fit and measurement procedure for the 4 2nd hinge side jamb A door Y package 2 Trim to length if U y necessary zs trim to fit When jambs are proper length slide the weather stripping flush sits on top to uncut end and trim excess of threshold from the cut end Assemble 3 piece frame On a clean flat surface suggest cardboard or moving blanket to protect paint finish place the top header jamb J and two hinge side ja
5. Bug sweeps weather stripping composite materials and hardware included with or installed on the security door are covered for one year from date of purchase Accessories fitted to the security door are not covered by this warranty including but not limited to locks handles rollers and closers These accessories may be covered by warranties provided by the manufacturer or supplier of the products Any problem caused by abuse misuse failure to follow care and maintenance instructions adjustments due to settling of the structure that the product is mounted on improper installation or acts of God are not covered Cutting parts not specified by the installation guide and parts drilled incorrectly are not included in this warranty If manufacturer defects occur Unique Home Designs will at our discretion either repair or replace the door If your home is burglarized and entry was accomplished through a UHD security door locked with the 3 point locking system while this warranty is in effect UHD will pay your insurance deductible up to 1000 or replace as applicable the damaged UHD security door at no charge Replacement items may vary in style due to changes in suppliers and product Not all colors can be reproduced if colors have been discontinued UHD is not responsible for any labor expense required to repair or replace the door UHD is not responsible for securing the property while warranted items are being repaired or replaced To make a cl
6. M SHT C Recessed Mount DUNIQI QUE Z HOME DESIGNS DESIGNS Premium Double Security Screen Door TITAN Kit Installation Instructions DISREGARD INSTRUCTIONS INCLUDED WITH DOOR PANELS e Read completely through the kit installation instructions before proceeding with installation e Installation requires two people e Use appropriate protective equipment including safety glasses e Children should not be allowed in work area e Failure to install door correctly could result in injury RETAIN PACKAGING DURING INSTALLATION Do NOT discard packaging materials until installation is complete PROFESSIONAL INSTALLATION RECOMMENDED Above average degree of difficulty Requires NETRA installation experience a mA NEED HELP J cates REVIEW INSTALLATION VIDEO ai mE Even professional installers will benefit from watching helpmeinstallit com E CONTACT US BEFORE RETURNING Customer service and technical support are available 1 866 317 8867 A pey support uhdco com Monday Friday 6 30am 4pm PST RECOMMENDED TOOLS Da T sa lt M fm 1 8 3 32 amp 7 64 Needle Nose Safety Glasses Measuring Tape Box Cutter minimum length 2 3 4 Pliers 1 2 Spade Bit O p lt A baa 1 2 Wood Chisel Tin Snips os fo Phillips head amp Flat blade P Square So oO Rubber Mallet ZZ T 2 x4 x6 Paintable Caulk amp screwdriver Level Shims Caulk Gun MK1300 03022015 Page 1 21010 810 82 DOUBLE DOOR KIT A Hinge side
7. aim under this Warranty send a brief written description of the problem a picture of the claim proof of purchase and your contact information to Unique Home Designs 973 N Colorado Street Gilbert AZ 85233 Attn Warranty Claims Meshtec is the registered Trade Mark of Meshtec International Co Ltd MTC in the United States and other various worldwide jurisdictions including registrations pending and may not be used without the prior written consent of MTC Extend Your Warranty When you register on line at uniquehd com registration Page 12
8. ck opening and pull the entire assembly out Page 6 Place the astragal L on There should be 1 8 Place astragal L back inactive door so the top gap between the bottom on inactive door so the edge is even with the top of the astragal L and top edge is even with edge of the door panel the threshold or stoop the top edge of the door Clamp in place Do NOT extend the panel Clamp in place astragal more than 1 Pre drill mounting holes past the bottom of the in the inactive door panel door panel Mark and through the 4 mounting remove astragal to trim if holes in the astragal necessary using a 3 32 drill bit Install top shoot bolt on inactive door D Install astragal on inactive door Attach the astragal L to Install latch hole the inactive door using plug AA into 10x1 flat head unused lower most screws X center latch hole Retract the shoot bolt P using Utilizing the mounting hole in Install top screw 8x1 flat head screw G Then the lever indicated by the red the shoot bolt P as a guide deploy the shoot bolt lever to expose the bottom dot With door panel laying on use a 7 64 drill bit to pre drill mounting hole Use a 7 64 drill bit to pre drill the hinge side slide the shoot bolt the exposed top mounting hole bottom mounting hole Finish attaching shoot bolt P in the top of the astragal so
9. eek OR Sloped trim may be removed or replaced with flat trim to properly mount your new security door Security Door Fits Door Opening Sizes Size wan Hom 64 x 80 63 3 4 64 3 8 80 80 7 8 72 x 80 71 3 4 72 3 8 If the opening identified does not fall within the fit range you can check to see if there is another mounting surface in your entryway that will work 4 minimum 4 minimum build your mounting surface out using stop or mounting Ready for installation nt similar trim or remove and reconfigure your trim to fall within the fit range CAUTION Check closely for possible hardware interference Stucco Top View Stud Stucco Minimum 2 5 8 P Pop out Check for Hardware Interference Measure the depth from the corner of your mounting surface to your existing entry door hardware If this measurement is 2 5 8 or greater there is no potential for hardware interference If the measurement is less than 2 5 8 measure from the edge of the mounting surface on top of the door to the top and bottom edge of the part of your existing hardware that intrudes into the 2 5 8 clearance If either of these two measurements falls between 40 1 4 and 44 1 4 the security door and existing door hardware will interfere with each other You can either build your mounting surface out to create the clearance required or mount your security door with an opposite swing to your main entry door t Entry Door Entry Door J C
10. ge 2 Identify and prepare mounting surface Inspect Your Entryway for Obstructions Brick Moulding Top View Check for any obstructions above and around your entryway that may prevent the outward swing Stud of your new security door and or its installation Entry Door Minimum 2 5 8 such as samb Brick t moulding trim m Light fixtures Low overhang aA 1 minimum 1 minimum Door bell m Trees bushes or hanging plants mounting mounting surface Ready for installation surface Determine Type and Readiness of Mounting Surface l _ Flat Trim Top View Your security door will require a minimum mounting surface of 1 on both sides of a corner Stud of the trim or jamb above and on both sides of Enty poor Minimum 2 5 8 your entry door Review diagrams at right and Flat Trim determine which one most resembles the trim PEE EE pian around the entry door to which you will mount mounting mounting your security door surface Ready for installation surface Measure Your Opening Sloped Trim Top View Measure between the edges of the left and right mounting surfaces for opening width Measure between the edge of the upper mounting surface Jamb Minimum 2 5 8 and the existing threshold for opening height Slaped Tuim Use the following chart and these measurements 1 minimum L Additional sloped trim may be added in the reverse 1 minimum to be sure the security door will fit your opening Bele direction to create a flat surface p
11. it is in the astragal L to astragal L using a 8x1 flat head screw G flush with the top edge of the astragal L Install top shoot bolt receiver cup Install the top shoot bolt receiver cup Q into the top header jamb J Using a hammer or rubber mallet gently tap the shoot bolt receiver cup into the pre cut hole in the top header jamb until flush Close the inactive door and deploy the shoot bolt P to test for proper fit Page 7 Install bottom shoot bolt on inactive door Slide the shoot bolt P into place inserting the inside edge first and rotating into position using needle nose pliers Retract the shoot bolt using the lever indicated by the red dot to expose the bottom mounting hole Be sure the shoot bolt P is flush with the bottom of the astragal L Pre drill the exposed mounting hole with a 7 64 drill bit Attach shoot bolt with 8x1 flat head screw G D Install bottom shoot bolt plate With top and bottom shoot bolts P retracted close the inactive door Deploy the top shoot bolt then deploy the bottom shoot bolt until it touches the stoop or threshold Mark the stoop or threshold where the shoot bolt touches Using a 1 2 drill bit create a 1 2 deep hole for shoot bolt P in stoop or threshold Deploy the shoot bolt lever to expose the top mounting ho
12. jambs 2 PARTS HARDWARE amp FASTENERS U 8x1 pan head screws 5 pcs A1 Hinge side snap covers 2 J Top header jamb P Shoot bolts 2 V 6 x5 8 pan head screws B Security screen doors 2 J1 Top header jamb Q Shoot bolt receiver cup 1 white 20 pcs C Hinges 6 snap cover R Shoot bolt covers 2 W 6x2 temporary dry wall D Locking handles 2 K Latch guard S Shoot bolt plate 1 screws 4 pcs E Lock cylinder 1 L Astragal T Weather stripping X 10x1 flat head screws 6 F 8x1 pan head screws 20 pcs M Bug sweeps 2 Y Plastic plugs white 6 pcs G 8x1 flat head screws 14 pcs N Dummy handles 2 Z Screw cover caps white 2 pcs H 14x3 4 pan head screws 2 O Dummy handle blocks 2 AA Latch hole plug 1 I Throw protector do not remove until BB Touch up paint step 7 Pa
13. le Pre drill the exposed top mounting hole using a 7 64 drill bit Complete attaching shoot bolt P to astragal L with 8x1 flat head screw G Place shoot bolt plate S over the hole close the inactive door and use the shoot bolt P to get proper alignment Retract shoot bolts open door and mark the mounting holes in the stoop or threshold Using a 1 8 drill bit pre drill holes and attach shoot bolt plate with 8x1 flat head screws G B Install inactive door dummy handle Make sure to orient handles in desired direction depending on right or left location of Install dummy handle block O on the back of each inactive door dummy handle N Tap block into place as needed so it is flush with the trim plate the interior of the active door and into the opposite dummy handle Attach the handles using two 1 fine thread bolts included with the handle set Leave each screw loose by 2 turn They will be tightened in step 16 Page 8 O 1 Start on the interior side of the door With the handle D facing toward the screen insert the spindle and mounting screws through the mortise gear in the door panel screw Install acti
14. m on edge of door frame NN Grab main throw with one hand and pull mortise lock part way out of edge of door Remove cylinder by removing set screw through edge of door panel and pulling cylinder out of the door Place other hand BEHIND the black plastic linkage connector and keep pressure on it so that it stays connected to the mortise lock as you pull the mortise lock until it is almost out of the door Remove handleset trim plates 2 mounting screws hold handles so they do not drop to floor y a Fully XG deployed With one hand still keeping pressure on the connector so it remains attached to the lock use the other hand to move the lockset down Listen for it to click the top and bottom lock throws will fully deploy AD Remove handles and Remove the 2 mortise spindle lock mounting screws in edge of door panel Re install the lockset spindle handleset cylinder and latch guard if removed by reversing the removal procedure Ensuring the linkage connecter stays attached to the back of the lockset raise and slide the lockset back into the door panel Page 9 O Install permanent mounting screws inner Pre drill through inner mounting holes using a 3 32 drill bit Install permanent screws 8x1 pan head screws U into the inside mounting h
15. mbs A into position Assemble the frame using 14x3 4 screws H Install screw at the top of each hinge side jamb allowing the screw to protrude 1 8 Fig 1 Attach the top header jamb J to each side jamb A by sliding the screw into the slots on the top header jamb Fig 2 Using a phillips head screw driver tighten the screws the rest of the way Fig 3 Install screw cover caps Z to cover open holes on top of header jamb If necessary trim weather stripping to length so it is a flush fit at each top corner of the frame Page 4 QO Install 3 piece frame Place the assembled 3 piece frame inside the opening Install two temporary mounting screws 6x2 temporary drywall screws W hinge side jamb A one at the top and one at the bottom Install one 6x2 temporary drywall screw W in the center of the top header jamb J C These screws are inserted to temporarily hold the jambs in place Do NOT install permanent screws until the door is completely up and working properly Check the shoot bolt receiving hole in the top header jamb J You will need a depth of 1 2 to install the shoot bolt receiver cup Q later in the installation If there is obstruction mark the receiving hole remove the temporary screws and remove the 3 piece frame to expose the mark made on the top mounting surface
16. oles As you install each screw check that the 1 8 reveal is maintained between the doors and that the 3 point locking trigger will engage You may need to shim between the doors if tightening or loosening screws does not maintain the reveal and 3 point lock trigger does not engage 20 Install latch guard Line the latch guard K provided in the double door kit up to the top of the astragal L Mark and trim flush ot the bottom of the door panel Using a 3 32 drill bit pre drill holes in the astragal through the mounting holes in the latch guard and astragal attach using five 6x5 8 pan head screws V 21 Pre drill through all outer mounting holes using a 3 32 drill bit Install permanent mounting screws 8x1 pan head screws F You may need to shim between the doors while tightening the screws to maintain the reveal between the doors and ensure proper space for the 3 point lock trigger to engage 22 Install bug sweeps Decide whether to place sweeps on back or front of door panels based on the configuration of your threshold Place trimmed active door bug sweep M against active door and adjust up or down until the bottom of the sweep rests on the threshold Attach bug sweeps using 6x5 8 pan head screws V Install plastic plugs Y over the bottom of the active door against the hinge side mounting holes jamb Mark where the active door meets the edge of the astragal mo
17. unted to the passive door and trim using tin snips Page 10 23 Install astragal weather stripping Install weather stripping T to the full length of the stop leg of the astragal L where the active door closes against the astragal Start at the top remove approximately 6 inches of the protective backing at a time and adhere to the astragal Slowly and carefully work your way down the full length of the door Trim at the bottom as needed D Install shoot bolt covers Install the shoot bolt covers R aP in the side of the astragal L to cover Meanie the internal mechanism of 1 the shoot bolts Using a box cutter trim to proper length 25 Install snap covers Place the snap cover A1 in the first hinge side jamb Fig 4 step 1 Using a rubber mallet hit on the side of snap cover seen in Fig 5 to securely snap cover into place Once snap cover is secured hold a wood block over the length of the snap cover and hit with mallet to smooth any irregularities in the snap cover surface Repeat process for the second hinge side jamb A1 and top header J1 snap covers Door jamb Snap cover Page 11 Final touch up suggestions Caulk not White Grease included Lubricant not Caulk around included the outside of Use white grease to the security door lubricate the hinges jamb frame using of your new security paintable caulk door and paint to the desired color
18. ve door handle and lockset 2 Move to the exterior of the active door With the handle pointing toward the active door panel hinges align the openings on the inside of the other handle D with the spindle and 2 mounting screws and position the handle against the door frame 3 While holding both handle trim plates in place tighten the mounting screws and then back off 2 turns These screws will be tightened after the lock cylinder is installed 4 From the inside of the door insert the lock cylinder E into the door through the trim plate Using a Phillips head screw driver tighten the retainer screw until snug Do NOT over tighten Tighten the two handle mounting screws until snug Retainer screw D Test locking mechanism With the door open retract the 3 point locking mechanism using the key or the thumb turn Keep the door OPEN and test the mechanism by first depressing the 3 point locking system trigger then deploying the locks using 3 Trigger the key or thumb turn If the locks will not deploy the system has been offset and must be manually reset If test is successful install screw cover caps included with door handles on interior and exterior sides of door handles If not proceed to step 18 before installing screw cover caps Reset locking mechanism IF REQUIRED q xe Sie Remove latch guard if installed 4 mounting screws 2 top 2 botto
Download Pdf Manuals
Related Search