Yamaha NS-C125 Owner's Manual
Contents
1.2. E Hookup NS C125 KOR ITER RoT _ SURROUND Amplifier or receiver e Loosen NS M125 Notes e Make sure that the bare wires are not touching each other as this could damage the speaker and amplifier e Connect one speaker to the left terminals of your amplifier and another speaker to the right terminals making sure not to reverse the polarity If one speaker is connected with reversed polarity the sound will be unnatural and lack bass E Using a Banana Plug 1 Remove the speaker terminal cover by gently pulling it toward you 2 Tighten the terminal knob 3 Simply insert the banana plug into the terminal Banana Plug E 5 Specifications NS M125 Type 2 way bass reflex speaker system magnetic shielding type Driver osn 8 cm 3 1 8 cone woofer x 2 2 2 cm 7 8 balanced dome tweeter Trapped ame srera 60 Frequency Response 70 Hz to 35 kHz Nominal Input Power eee eens 40 W Maximum Input Power eee 120 W Sensitivity 0 eee eeeeeeeeeee sees 86 dB 2 83 V m Crossover Frequency eeeeeeeeeeeeeeseeeees 6 kHz Dimensions W x H x D NS C125 Typenr 2 way bass reflex speaker system magnetic shielding type Driver sssrinin 8 cm 3 1 8 cone woofer x 2 2 2 cm 7 8 balanced dome tweeter Tipiped ance iiteraria 60 Frequency Response 70 Hz to 35 kHz Nominal Input Power eens 40 W Maximum Input Power
3. YAMAHA URG Owner s Manual NS P125 HOME CINEMA CENTER amp EFFECT SPEAKERS NS C125 NS M125 SPEAKER SYSTEM Thank you for choosing a Yamaha speaker system NS P125 are speaker sets consisting of the components shown on the table NS C125 x 1 NS M125 x 2 e Center speaker e Effect Surround speakers NS P125 The NS C125 spekaer is designed for use as the center speaker in a surround sound system NS M125 speakers are designed for use as front or surround speakers in a surround sound system Caution E Read the following before using these speakers To assure the finest performance please read this manual carefully Keep it in a safe place for future reference Install the speakers in a cool dry clean place away from windows heat sources sources of excessive vibration dust moisture and cold Avoid sources of humming transformers motors To prevent fire or electric shock do not expose the speakers to dripping or splashing To prevent the enclosure from warping or discoloring do not place the speakers where they will be exposed to direct sunlight or excessive humidity Do not place the following objects on top of the speakers 1 Glass china etc If glass etc falls by vibrations and breaks it may cause personal injury 2 A burning candle etc If the candle falls by vibrations it may cause fire and personal injury 3 A vessel with water in it If the vessel fa
4. uu eee 120 W DENSIIVILY eocenie 86 dB 2 83 V m Crossover Frequency eeeeeeeeeseeeeee 6 kHz Dimensions W x Hx D eee 105 4 1 x 340 13 4 x 133 5 2 mm seaseeeessse 340 13 4 x105 4 1 x 132 5 2 mm Weight co aisapdeseieielaeedzeaa aie 2 kg 4 4 Ibs Weight csccccssssssesssssssseessssssseeesessens 2 kg 4 4 Ibs Specifications are subject to change without notice due to product improvements YAMAHA This product mainly uses lead free solder Cet appareil utilise principalement de la soudure sans plomb CoN T Dieses Produkt verwendet haupts chlich bleifreies Lot Este producto utiliza principalmente soldadura sin plomo 2004 YAMAHA CORPORATION All rights reserved YAMAHA ELECTRONICS CORPORATION USA 6660 ORANGETHORPE AVE BUENA PARK CALIF 90620 U S A YAMAHA CANADA MUSIC LTD 135 MILNER AVE SCARBOROUGH ONTARIO M1S 3R1 CANADA YAMAHA ELECTRONIK EUROPA G m b H SIEMENSSTR 22 34 25462 RELLINGEN BEI HAMBURG F R OF GERMANY YAMAHA ELECTRONIQUE FRANCE S A RUE AMBROISE CROIZAT BP70 CROISSY BEAUBOURG 77312 MARNE LA VALLEE CEDEX02 FRANCE YAMAHA ELECTRONICS UK LTD YAMAHA HOUSE 200 RICKMANSWORTH ROAD WATFORD HERTS WD187GQ ENGLAND YAMAHA SCANDINAVIA A B J A WETTERGRENS GATA 1 BOX 30053 400 43 V STRA FR LUNDA SWEDEN YAMAHA MUSIC AUSTRALIA PTY LTD 17 33 MARKET ST SOUTH MELBOURNE 3205 VIC AUSTRALIA YAMAHA CORPORATION Printed in Indonesia unp WD74170 1
5. vibrations may cause them to fall down e To avoid accidents resulting from tripping over loose speaker cords fix them to the wall Note You can also use the screw holes on the bottom of the NS M125 for installing the speakers on commercially available speaker stands Ascrew with a diameter of 6 mm 1 4 can be used Hole depth 20 mm 3 4 Before installing please refer to the instruction manual of the speaker stand E 3 E Placing the center speaker NS C125 Place the speaker on the floor under the TV or inside the TV rack so that it is stabilized When placing the speaker on top of the TV To prevent the speaker from falling down put the provided fasteners at two points on both bottom of the speaker and top of the TV NS C125 Peel off the seal Notes Do not place the speaker on top of the TV whose area is smaller than the bottom area of the speaker If placed the speaker may drop out causing an injury to you Do not place the speaker on top of the TV with an inclination Do not touch the adhesive surface after peeling off the seal as this will weaken its adhesive strength Thoroughly wipe clean the surface where the fastener is to be applied Note that adhesive strength is weakened if the surface is dirty oily or wet and that this may cause the center speaker to drop E Mounting the center speaker NS C125 on the wall The speaker ca
6. ilt stand E Using the NS M125 as Normal Stereo Speakers To get the best stereo performance angle the speakers inward so as to create a triangle with the listener at the apex Ca E Using the NS M125 as Front Speakers in a Surround Sound System Position the speakers both side of your TV The positioning of these speakers is important because they provide a solid anchor for the sound image They should be positioned facing the listener at about ear level and equidistant from the TV E Using the NS M125 as surround speakers in a surround sound system The speakers can be mounted on a wall by using the bracket attached to the speakers back panels mE Holes Make sure that the screws are caught by a narrow part of the holes securely 26 mm 1 Fasten screws into a firm wall or wall support as shown in the figure below and hang the holes on the protruding screws NS M125 Diam 3 5 to 4 mm 1 8 1 8 e Tapping screw commercially available Wall or wall support WARNING e Each speaker weights 2 kg 4 4 Ibs Do not mount them on thin plywood or soft wall surface material as the screws may come out of the flimsy surface causing the speakers to fall down and be damaged or result in personal injury e Do not fasten the speakers to wall with nails adhesives or other unsound hardware Long term use and
7. lls by vibrations and water spills it may cause damage to the unit and or you may get an electric shock Do not place the speakers where foreign objects such as water drips might fall It might cause a fire damage to this unit and or personal injury Do not place the speakers where they are liable to be knocked over or struck by falling objects Stable placement will also ensure better sound performance Secure placement or installation is the owner s responsibility Yamaha shall not be liable for any accident caused by improper placement or installation of speakers Any time you note distortion reduce the volume of your amplifier immediately Make sure the input power does not exceed the specified maximum input power otherwise the speakers will be damaged Do not attempt to clean the speakers with chemical solvents as this might damage the finish Use a clean dry cloth Do not attempt to modify or fix the speakers Contact qualified Yamaha service personnel when any service is needed The cabinet should never be opened for any reasons Note The speakers are magnetically shielded but placing them too close to a TV may impair the TV picture If this happens move them away from the TV Supplied Accessories e NS M125 Speaker cable 10 m 1 pc unit e NS C125 Fasteners x 2 E 2 Setting Up the Speakers Place the speakers on a sturdy vibration free surface such as a well bu
8. n be mounted on a wall by using the bracket attached to the speaker s back panel f Make sure that the screws are caught by a narrow part of the holes securely 292 mm 11 1 2 Fasten screws into a firm wall or wall support as shown in the figure below and hang the holes on the protruding screws NS C125 a Diam 3 9 tO 4 mm 1 8 4 Wall or wall support Tapping screw commercially available E 4 WARNING The speaker weights 2 kg 4 4 Ibs Do not mount them on thin plywood or soft wall surface material as the screws may come out of the flimsy surface causing the speakers to fall down and be damaged or result in personal injury Do not fasten the speakers to wall with nails adhesives or other unsound hardware Long term use and vibrations may cause them to fall down To avoid accidents resulting from tripping over loose speaker cords fix them to the wall Connecting Your Speakers Always turn off your amplifier or receiver before making any connections E Preparing Your Speaker Cables Carefully remove 10 mm 3 8 of insulation from both ends of your 10 mm speaker cables and twist the bare wires tightly as shown 3 8 Good No Good
Download Pdf Manuals
Related Search