Xantech Switch 282TP User's Manual
Contents
1. xantecn MODEL 282TP Mouse Emitter Twin Plug INSTALLATION INSTRUCTIONS OMNG2777N5154 513 DESCRIPTION The 282TP Twin Plug Emitter is based on Xantech s standard 282M Mouse emitter with two 3 5mm Mono Mini plugs each with diode isolation The twin plug feature allows a single emitter to be shared by two IR sources For instance one mouse emitter can now be connected to both an IR receiver and a Xantech Multi Zone Controller without having to place two emitters on the front of the IR Controllable component Internally the 282TP contains components that are designed to keep the IR signal path directed towards the emitter only allowing both control systems to be completely isolated The plugs are gold plated to increase durability and connectivity Side View Sr NOTE White vi side is positive l View 3 5mm mono mini plugs a ai 10 FT IFT INSTALLATION e Each emitter has a clear adhesive layer on the bottom flat surface of the shell The rounded side faces the user and emits visible light when a command is sent e Simply peel off the adhesive cover and affix the emitter to the center of the IR sensor window on the controlled component s front panel Internal IR Emitter High S H ee Low Output lt S Output Side g gt Side eN Clear adhesive layer Replace if necessary with a short piece of the 2 sided tape supplied Emitter y Shell Mini wire lea2. d e n some cases it may be difficult to find the location of the IR sensor on the component Consult the owner s manual of the unit or the manufacturer for the exact IR sensor window location e Double sided adhesive tape is included If you move the emitter to a different component use this tape to replace the current adhesive layer for the best adhesion e The shell though dark in appearance is transparent to infrared light allowing commands from a handheld remote control to pass through it This permits direct control of the equipment from a handheld remote as well as from the 282TP xantecn 13100 Telfair Ave 2 F Sylmar CA 91342 www xantech com CONNECTING THE EMITTERS e Simply insert the mono mini plug of the 282TP emitter into the EMITTERS or OUT jacks on any of the Xantech Connecting Blocks or Controllers e CAUTION DO NOT plug emitters into the IN OUT or HIGH OUT jacks on the 790 00 and 791 44 Connecting Blocks To do so will destroy the emitters e The 282TP mouse emitter will also indicate the presence of stray IR or RF interference by randomly blinking when no IR control signal is being sent Reposition the IR receiver of the interfering source to eliminate or reduce the random blinking The more the random blinking is reduced the better the system will function e An optional shield available from Xantech as model MS 1 fits over the emitter head and the sensor window of the controller co
3. ects in materials or workmanship This warranty extends for one year from the date of purchase by the original consumer Any products returned to Xantech and found to be defective by Xantech within the warranty period will be repaired or replaced at Xantech s option at no charge Xantech will not be responsible for the actual cost of installation or removal of the product nor for any incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights You may have additional legal rights that vary from state to state 08901676A
4. mponent Mouse Emi or Shiek Adhes Si T ayer EE i 283M Emater M 1 and 263M installed over IF garmor wandow Top View Side View INSTALLATION SETUP 1 Home Theater Multi room Controller The setup below shows two IR signals connected to a single source This allows the source to be controlled from two areas One mono plug goes to the connecting block The other mono plug is connected to the MRC44 Controller Satellite Receiver T81RG Power Supply IR Sensor Window i 2821P Emitter D a eT PRU HREH Controller rear M2078 SNLLIANWOD Pr6EL ani 101R Receiver I m Hand Held Remote INSTALLATION SETUP 2 Expanded Multi room Controller The setup below shows two MRAUDIO4X4 Controllers connected in Expansion mode Expansion mode doubles the number of zones while using the same number of sources The benefit of the 282TP is that you only need to place one emitter at each source One mono plug is connected to the master controller The other mono plug is connected to the slave controller This application can apply to the entire product line of Xantech controllers MRAUDIOAXACTL or BAAUDIOSXACTL master oe 2 el E T 2 nae i x eres ir a ro cepa lmee eee el Ge co 1 bOn i E 9 9 9 Saal ar JHJ at i i TEs r tl m f aJi A H m 5 TL Limited Warranty Xantech warrants its products to be free pf def
Download Pdf Manuals
Related Search