Westinghouse MT80A TILT User's Manual
Contents
1. Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding power Tools Needed for Assembly stud finder edge to edge stud finder is recommended phillips screwdriver drill 1 4 bit for concrete and cinder block wall 1 2 bit for metal stud wall 5 32 bit for metal or wood stud wall level Accessories e Metal Stud Fastener Kit ACC 215 Not evaluated by UL e Video Conferencing Shelf ACC 309 Not evaluated by UL e Accessory Shelves PM 600 PM 610 Not evaluated by UL Table of Contents Pants E a AEA AEE EI EPS TONOA SOPI ORRE EEE EETA EAE EAE EE EAEE E A E E EEEO 3 Installation to Single Wood Stud Wall wiic 4sciha Meet en ea dl i es ee 4 Installation to Solid Concrete or Cinder BlOCK wiis sic ent ei dee need ed eee A 5 Attaching Adapter Plate to Flat Panel Sorem 0 eccccccccseeececneeeeeeneeeeeeeaee i E a E aa EA AAE Aea a 6 Installing and Removing Flat Panel SoreeMasniicncniienn n a a a a Tiaa Na aA RLR TN 7 Adjusting the Tilt Angle of the Flat Panel Seren oniiir aean A Eaa AE Aa eaaa 7 For customer care call 1 866 287 5555 2of8 ISSUED 01 17 06 SHEET 202 9091 1 Parts List Description adapter plate tilt assembly Alligator anchor M4 x 10 mm phillips screw M4 x 20 mm phillips screw retaining spacer 14 x 2 1 2 hex head wood screw M5 x 6 mm screw nNFfR BY HH 095 4346 095 0360 590 0097 504 9012 5042. w Westinghouse Installation and Assembly Universal Tilt Wall Mount for 15 37 Screens Model MT80A TILT Features e Fits 15 to 37 flat panel screens e One touch tilt for effortless positioning and adjustment of the screen This product is intended for use with UL Listed products and must be installed by a C US qualified professional installer Max UL Load Capacity 80 Ib 36 3 kg Visit the Westinghouse Web Site at www westinghousedigital com For customer care call 1 866 287 5555 ISSUED 01 17 06 SHEET 202 9091 1 Note Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Westinghouse product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings please call customer care at 1 866 287 5555 This product should only be installed by a qualified professional Make sure that the wall will safely support the combined load of the equipment and all attached hardware and compo nents Never exceed the Maximum UL Load Capacity of 80 Ib 36 3 kg If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment
3. 9020 590 5005 5S1 015 C03 520 1023 3 of 8 ISSUED 01 17 06 SHEET 202 9091 1 Installation to Single Wood Stud Wall e Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components Use a stud finder to locate the edges of the stud Use of an edge to edge stud finder is highly recommended Based on its edges draw a vertical line down the stud s center Place tilt assembly B on wall as a template making sure that the two mounting holes are over the stud centerline Level tilt assembly and mark the center of the two holes Drill two 5 32 4 mm dia holes 2 1 2 65 mm deep Make sure that the tilt assembly is level secure it using two 14 x 2 1 2 wood screws G as shown Skip to step 2 on page 6 Tighten wood screws so that tilt assembly is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in lb 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware for other types of mounting situations 4of8 ISSUED 01 17 06 SHEET 202 9091 1 Installation to Solid Concrete or Cind
4. backward CAUTION e Do not tighten screws with excessive force Overtightening can cause damage to mount Tighten screws to 40 in Ib 4 5 N M maximum torque TENSION KNOB A CAUTION e Be careful not to pinch fingers when pushing screen from the bottom 7of8s ISSUED 01 17 06 SHEET 202 9091 1 W Westinghouse Limited Five Year Warranty Westinghouse Digital Electronics warrants to original end users of this Westinghouse display mounting product the Product that the Product will be free from defects in material and workmanship under normal use for a period of five 5 years from the date of purchase by the original end user subject to the following terms and conditions REPAIR OR REPLACEMENT For a period of five 5 years from the original date of purchase Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product or at its option replace a defective Product Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety 90 days from the date of delivery to the end user whichever occurs last OBTAINING WARRANTY SERVICE To obtain warranty services you must either personally deliver or ship the Product to Westinghouse Digital Electronics freight prepaid Please call Westinghouse Digital Electronics at 866 287 5555 to obtain a Return Merchandise Authorization RMA and for other instr
5. ecific legal rights and you may also have other rights which vary from State to State Westinghouse Digital Electronics LLC 12150 Mora Drive Santa Fe Springs CA 90670 Tel 562 236 9800 Fax 562 236 9898 8 of 8 ISSUED 01 17 06 SHEET 202 9091 1 and Westinghouse are trademarks of Westinghouse Electric Corporation and are used under license
6. er Block A WARNING e When installing Westinghouse wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual con crete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount ina solid part of the block generally 1 minimum from the side of the block Cinder block must meet ASTM C 90 specifica tions It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity e Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components concrete template to mark two mounting holes Drill two 1 4 6 mm dia holes to a minimum depth of 2 1 2 Make sure that tilt assembly B is level use itas a surface 64 mm Insert anchors C in holes flush with wall Ewe as shown right Place tilt assembly over anchors and secure with two 14 x 2 1 2 screws G Level C then tighten all fasteners A WARNING Tighten screws so that wall plate is firmly attached but do not overtighten Overtightening can damage screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M A WARNING e Always attach concr
7. ete expansion anchors directly to load bearing concrete with screws G EAA I 7 4 _qx Never attach concrete expansion anchors to concrete covered with plaster drywall or other finishing mate Tighten all fasteners rial If mounting to concrete surfaces covered with a finishing surface is unavoidable the finishing surface must be counterbored as shown below Be sure concrete anchors do not pull away from concrete when tightening screws If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer CORRECT INCORRECT Oconerete concrete uJ ao C CUTAWAY VIEW 5of8 ISSUED 01 17 06 SHEET 202 9091 1 Attaching Adapter Plate to Flat Panel Screen A WARNING e If screws don t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured damage may occur to screen or product may fail FOR VESA 75 MOUNTING PATTERN FOR VESA100 MOUNTING PATTERN Choose hole pattern as shown below Attach adapter Choose hole pattern as shown below Attach adapter plate A to back of screen using four M4 x 10 mm plate A to back of screen using four M4 x 10 mm screws D as shown below screws D as shown below Note If hole pattern is in a pocket attach adapter plate A to back of screen using four M4 x 20 mm screws E and four retainin
8. g spacers F as indicated below For screens with a hole pattern in a pocket spacers F go between adapter plate A and screen 6 of 8 ISSUED 01 17 06 SHEET 202 9091 1 Installing and Removing Flat Panel Screen Attach screen to tilt assembly B Tighten M5 x 6 mm screw H to lock screen to tilt assemby Note For security models use security driver I to tighten M5 x 6 mm screws H To remove screen from mount loosen screw H and lift screen off of mount A WARNING e Do not lift more weight than you can handle Use additional man power or mechanical lifting equipment to safely handle placement of the screen e Failure to lock adapter plate A with screw H can cause screen to come off mount if hit accidentally CAUTION e Do not tighten screws with excessive force Overtightening can cause damage to mount Tighten screws to 20 in lb 2 26 N M maximum torque Adjusting the Tilt Angle of the Flat Panel Screen Adjust tension knob on right side of mount shown in figure 4 to desired tension to balance your screen size and weight Note If knob is inaccessible remove screen from mount adjust tension knob to desired tension to balance your screen size and weight and reattach screen to mount as stated in step 3 Push or pull from top or bottom of screen to adjust tilt as shown in figure 4 The tilt can be adjusted to a maximum of 15 forward or 5
9. uctions regarding return and replacement or repair of the Product Westinghouse Digital Electronics will not accept Products delivered to it without an RMA EXCLUSIONS TO WARRANTY This warranty does not cover damage caused by a service or repairs by anyone other than personnel authorized by Westinghouse Digital Electronics b the failure to utilize proper packing when returning the product c improper installation or the failure to follow Product instructions or warnings or d misuse or accident in transit or otherwise PROOF OR ORIGINAL PURCHASE A sales receipt invoice or other proof of purchase specifying the original date of purchase within the five 5 year warranty period must be presented to obtain warranty service This warranty extends to the original purchaser and is not transferable EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY EXCEPT TO THE EXTENT PROHIBITED BY LAW WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION AND SCOPE TO THE TERMS OF THIS WARRANTY Some States do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives sp
Download Pdf Manuals
Related Search