Home

Vision Fitness T9100 User's Manual

image

Contents

1. Assembly Guide 6 VISION X FITNESS T9100 AND T9000 PLATFORM TREADMILLS Assembly Guide T9100 AND T9000 PLATFORM TREADMILLS To avoid possible damage to this treadmill please follow these assembly steps in the correct order Before proceeding find your new treadmill s serial number located on the front axle tube and enter here Please refer to this number when calling for service Enter this serial number on your Warranty Card and in your own records Be sure to read your Owner s Guide before using your new treadmill If any parts hardware or tools are missing please call 1 800 335 4348 Extension 12 NOTE It is recommended that you apply grease to the threads of each screw as you assemble your treadmill to prevent loosening and noise Also during each assembly step ensure that ALL screws are in place and partially threaded in before completely tightening any ONE screw or bolt TOOLS amp PARTS INCLUDED 6 Allen Wrench Screwdriver v Water Bottle Qty 1 Color coded Hardware Bags Owner s Guide A Assembly Guide 5 L Shaped Wrench Warranty Card HARDWARE INCLUDED e Insert one of the console supports into the console support bracket and secure with three bolts M8x651 in the side of the console support bracket e Secure the rear of the console support using
2. calibrate minimum and maximum speed and minimum and maximum elevation When Auto Calibration is complete the treadmill will reset to User s start screen This process takes three to five minutes BELT TENSION e If the running belt slips when used use the supplied 6mm Allen wrench to turn the left and right tension bolts clockwise 1 4 turn at a time until the belt no longer slips e If the running belt is too far to the right side use the supplied 6mm Allen wrench to turn the right tension bolt clockwise 1 4 turn at a time until the belt stays centered during use If the running belt is too far to the left side turn the left tension bolt clockwise 1 4 turn at a time until the belt remains centered during use U VISION X FITNESS 500 South CP Avenue P O Box 280 Lake Mills WI 53551 toll free 1 800 335 4348 phone 1 920 648 4090 fax 1 920 648 3373 www visionfitness com 2002 Vision Fitness All Rights Reserved 10 03 Part 290TM78 AG18 27PRD AG18 27PRD REV2
3. bolt M8x20L e Use the 5mm L shaped Allen wrench to tighten all bolts e Repeat this step on the opposite side NOTE The right console support has a white wire tie attached to it BLUE BAG e Slide the data cables down the righ console support using the white wire tie as a guide Make sure that the data cables come out the hole in the side of the console support e Mount the console to the console mast using the four flathead bolts M8x201 and tighten with the blue handled 5mm L shaped Allen wrench NOTE Push all extra data cable into the console mast Make sure not to pinch or cut the data cable Plug the large data cable into the large plug connection on the lower control board Plug the small data cable into the small plug connection on the lower control board e Install the motor cover Secure the motor cover using the four M5x2OL screws AUTO CALIBRATION e Once the treadmill is plugged in you need to perform an Auto Calibration to assure maximum performance DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO CALIBRATION e With the SAFETY KEY in place hold the ELEVATION UP and SPEED DOWN buttons for five seconds The console will beep twice ENGO will appear in the Distance window and a number will apear in the Elevation window e Press SELECT until ENG3 appears this is for Auto Calibration Press START to Auto Calibrate e The treadmill will

Download Pdf Manuals

image

Related Search

Related Contents

Dell Vostro 3360 Manual do Proprietário  Weider WEEVBE3303 User's Manual  Guía del usuario  detailed specifications.  S-Box Operating Instructions    Gorenje BO71ORAX  Samsung MM-ZJ9 Наръчник за потребителя  ZySCAN Manual  2012 年 4 月号/No.3  

Copyright © All rights reserved.
Failed to retrieve file