SMC Networks SMC7500A/VCP User's Manual
Contents
1. lt N E AC Power Adapter Telephone Fax or Modem Using standard telephone cable connect the CPE s RJ 11 LINE port to the RJ 11 telephone wall jack providing the VDSL service Connect a telephone or fax machine to the RJ 11 port on the CPE labeled PHONE For the Ethernet connection make sute you have installed a 10 100BASE TX network adapter card in the computer Prepare straight through shielded or unshielded twisted pair cables with RJ 45 plugs at both ends Use 100 Ohm Category 3 4 or 5 cable for a 10 Mbps Ethernet connection or Category 5 cable for a 100 Mbps connection Connect one end of the cable to the RJ 45 port of the network interface card and the other end to the RJ 45 LAN port on the CPE POWERING ON When inserting an RJ 45 plug be sure the tab on the plug clicks into position to ensure that it is properly seated Caution Do not plug a phone jack connector into any RJ 45 port Use only twisted pair cables with RJ 45 connectors that conform to FCC standards Notes 1 When connecting to a hub or switch use crossover cabling Refer to Port And Cable Assignments on page 15 for a description of crossover cable 2 Make sure the twisted pair cable connected to the CPE LAN port does not exceed 100 meters 328 feet Powering On Plug the power adapter cord into the DC 12V power socket on the side of the CPE then plug the power adapter di2. e Check that the network adapter s speed or duplex mode has not been configured manually Note that it is recommended to set the adapter to auto negotiation when installing the network driver Port And Cable Assignments Caution Do not plug a phone jack connector into any RJ 45 port Use only twisted pair cable with RJ 45 connectors that conform with FCC standards An Ethernet twisted pair link segment requires two pairs of wires Each wire pair is identified by two different colors Each wire pair must be attached to the RJ 45 connector in the orientation detailed below 8 The RJ 45 Ethernet port on the Tiger Access Extended Ethernet CPE is an MDI port which means you must use a cross over cable when connecting to like devices MDI to MDI For connection to hubs or switches that have MDI X ports a straight through cable must be used In straight through cable pins 1 2 3 and 6 at one end of the cable are 15 TROUBLESHOOTING connected straight through to pins 1 2 3 and 6 at the other end of the cable Pin MDI X Signal MDI Signal Name Name 1 Receive Data plus Transmit Data plus TD RD 2 Receive Data minus Transmit Data minus TD RD 3 Transmit Data plus Receive Data plus RD TD 6 Transmit Data Receive Data minus RD minus TD 4 5 7 8 Not used Not used Straight Through Cable If the twisted pair cable is to join two ports and only one of the ports h
3. Fructu s Gelabert 6 8 2 43 08970 Sant Joan Despi Barcelona Spain This information technology equipment complies with the requirements of the Council Directive 89 336 EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73 23 EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93 68 EEC For the evaluation of the compliance with these Directives the following standards were applied RFI Emission Limit class B according to EN 55022 1998 Limit class A for harmonic current emission according to EN 61000 3 2 1995 Limitation of voltage fluctuation and flicker in low voltage supply system according to EN 61000 3 3 1995 Immunity Product family standard according to EN 55024 1998 Electrostatic Discharge according to EN 61000 4 2 1995 Contact Discharge 4 kV Air Discharge 8 kV Radio frequency electromagnetic field according to EN 61000 4 3 1996 80 1000MHz with 1kHz AM 80 Modulation 3V m Electrical fast transient burst according to EN 61000 4 4 1995 AC DC power supply 1 kV Data Signal lines 0 5kV Surge immunity test according to EN 61000 4 5 1995 AC DC Line to Line 1 kV AC DC Line to Earth 2 kV Immunity to conducted disturbances Induced by radio frequency fields EN 61000 4 6 1996 0 15 80MHz with 1kHz AM 80 Modulation 3V m Power frequency magnetic field immunity test according to E
4. ON adapter may be Check the power adapter with another defective device LAN LINK Network e Verify that the CPE and computer are indicator does interface e g a powered on not light up after network adapter e Be sure the cable is plugged into both making a card in the the CPE and the computer JON attached e Verify that the proper cable type is computer used and its length does not exceed network cable or Specified limits CPE LAN port p 3 i may be defective Check the network adapter in the computer and cable connections for possible defects Replace the defective adapter or cable if necessary LINE LINK VDSL switch Verify that the CPE and attached indicator does cabling or CPE VDSL switch are powered on notlightupafter LINE port may Be sure the cable is plugged into both making a be defective the CPE and an RJ 11 telephone jack connection Verify that the cable length does not exceed specified limits Check the cable connections on the CPE wall jack punch down block patch panel and the VDSL switch for possible defects Replace the defective cable if necessary 14 IF YOU CANNOT CONNECT TO THE INTERNET If You Cannot Connect to the Internet e Check that your computer is properly configured for TCP IP See Configuring the TCP IP Protocols on page 11 Make sure the correct network adapter driver is installed for your operating system If necessary try reinstalling the driver
5. by one or mote of the following measures Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note In order to maintain compliance with the limits of a Class B digital device SMC requires that you use a quality interface cable when connecting to this device Changes or modifications not expressly approved by SMC could void the user s authority to operate this equipment Industry Canada Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of Industry Canada Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe B prescrites dans la norme sur le material brouilleur Appareils Num riques NMB 003 dict e par PIndustrie Japan VCCI Class B COREL HROUBRESSRESREMHMBS VCCI DEE I CESO lt ZJTSXBIRKIEET J CORES ZERHTEAFSIE ERHELTIV J CORE OFZ OF LES SIEMITMELT KAANDZEREBELZIERLTIENBUFT AY PRL RABI HE gt TELVMYRUAELTTEN iti COMPLLANCES EC Conformance Declaration Class B SMC contact for these products in Europe is SMC Networks Europe Edificio Conata II Calle
6. dial up delays providing transparent reconnection when initiating a network reguest Supports evolving ETSI ANSI and ITU VDSL standards for the copper local loop PACKAGE CHECKLIST Spectral compatibility with xDSL ISDN 2B10 4B3T Smartphone digital PBX extensions and narrowband interference Robust operation on severely distorted lines Supports power back off algorithm that permits a mixed distance deployment Simple plug and play installation LEDs indicate VDSL link status and power Simple plug and play installation Package Checklist The EZ Connect Tiger Access Extended Ethernet CPE package includes 1 TigerAccess Extended Ethernet CPE SMC7500A VCP 4 rubber foot pads 1 standard telephone cable 2 1m 7 ft 1 Category 5 UTP network cable 1 8m 6 ft 1 AC power adapter This User Guide Please register this product and upgrade product warranty at www smc com Please inform your dealer if there are any incorrect missing or damaged parts If possible retain the carton including the original packing materials Use them again to repack the product in case there is a need to return it for repair TIGERACCESS EXTENDED ETHERNET CPE System Reguirements Before you start installing the SMC TigerAccess Extended Ethernet CPE make sure you can provide the right operating environment See the following installation reguirements A PC or Macintosh with a 10 100 Mbps Ethernet adapter card installed
7. downstream receive direction than in the upstream transmit direction TIGERACCESS EXTENDED ETHERNET CPE VDSL delivers high performance online applications such as high quality video and other switched multimedia services SMC s Ethernet VDSL CPE system provides robust performance with a symmetric data rate up to 15 Mbps and a range up to 1770 m 5800 ft SMC s system is based on advanced VDSL OAM Ouadrature Amplitude Modulation technology with adaptive channel egualization that overcomes bridge taps and other line distortions Reed Solomon Forward Error Correction and interleaving protects against errors due to impulse noise and enables recovery from signal interruptions Frequency Division Duplexing FDD separates downstream and upstream channels and allows VDSL signals to coexist with regular telephone services A power back off mechanism is also implemented to reduce noise from crosstalk in line bundles Features and Benefits VDSL features CPE side include High speed Internet access over existing phone lines VDSL connection provides the following rate range options Rate Mode Max Range 15 Mbps Symmetric 1070 m 3500 ft 10 Mbps Symmetric 1220 m 4000 ft 5 Mbps Symmetric 1370 m 4500 ft 4 Mbps downstream Asymmetric 1770 m 5800 ft 1 Mbps upstream e Concurrent data and telephone services voice ISDN over a single connection Always on digital connection eliminates
8. list of discontinued products with their respective dates of discontinuance can be found at http www smc com index cfm action customer service warranty All products that are replaced become the property of SMC Replacement products may be either new or reconditioned Any replaced or repaired product catries either a 30 day limited warranty or the remainder of the initial warranty whichever is longer SMC is not responsible for any custom software ot firmware configuration information or memory data of Customer contained in stoted on or integrated with any products returned to SMC pursuant to any warranty Products returned to SMC should have any customer installed accessory or add on components such as expansion modules removed prior to returning the product for replacement SMC is not responsible for these items if they are returned with the product Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC Proof of purchase may be reguired Any product returned to SMC without a valid Return Material Authorization RMA number clearly marked on the outside of the package will be returned to customer at customer s expense For warranty claims within North America please call our toll free customer support number at 800 762 4968 Customers are responsible for all shipping charges from their facility to SMC SMC is responsible for return shipping charges from SMC to customer LIMITED WA
9. oossoo cece S 14 If You Cannot Connect to the Internet o ooooooomomoooo o 15 Port And Cable Assignments soolon nn 15 Straight Through Cable 244 200 an tan eee 16 Crossovet Gable coi o a tii Br 17 RJAL POS 22 ii A Dee ee eee A 17 SPECHICATIONS tias we os A Baal 19 vii TABLE OF CONTENTS viii TIGERACCESS EXTENDED ETHERNET CPE Introduction SMC s TigerAccess Extended Ethernet CPE system consists of end user CPE Customer Premise Equipment and a VDSL switch that are connected by standard telephone cable The VDSL connection delivers an Ethernet data link rated up to 15 Mbps symmetric full duplex while simultaneously supporting standard telephone services The system can be deployed in any multi dwelling multi tenant environment apartment blocks hotels or office complexes to provide both high speed Internet access and telephone services without any need for re wiring SMC s VDSL switches combine both the data and phone signals coming from your Internet and telephone service providers and pass these signals directly over standard telephone wiring to multiple users in the same building The SMC7500A VCP CPE is used to separate these signals and pass them on to a customer s computer and telephone eguipment In building connections operate at up to 15 Mbps over runs up to 1070 m 3500 ft 10 Mbps for runs up to 1220 m 4500 ft 5 Mbps for runs up to 1370 m 4500 ft and asymmetric 4 Mbps downstream 1 Mbps u
10. 2 2659 9666 Asia Pacific 65 238 6556 Fax 65 238 6466 Korea 82 2 553 0860 Fax 82 2 553 7202 Japan 81 3 5645 5715 Fax 81 3 5645 5716 Australia 61 2 9416 0437 Fax 61 2 9416 0474 India 91 22 8204437 Fax 91 22 8204443 If you are looking for further contact information please visit www smc com or www smc europe com SMC Networks 38 Tesla Irvine CA 92618 Phone 949 679 8000 Model Number SMC7500A VCP Part No 750 5871 Publication No 150000010900A R02
11. 35 S S S 2 x 5 3 S SZ S 8322 m a o mos R1T1 T2R1T1R2 T2R1T1R2 123456 12 3456 24510516 6x2 Jack 6x4 Jack 6x4 Jack T Tip R Ring Pin Signal Name Wire Color 1 Not used 2 Line 2 Tip Black or White Orange 3 Line 1 Ring Red or Blue White 4 Line 1 Tip Green or White Blue 5 Line 2 Ring Yellow or Orange White 6 Not used 18 Functional Criteria Data Rate Range VDSL Specifications VDSL Standards Modulation Ports Physical Characteristics Current Consumption Input Power Size Weight Temperature Humidity LED Indicators 19 SPECIFICATIONS 15 Mbps symmetric up to 1070 m 3500 ft 10 Mbps symmetric up to 1220 m 4000 ft 5 Mbps symmetric up to 1370 m 4500 ft 4 Mbps downstream 1 Mbps upstream asymmetric up to 1770 m 5800 ft Supports evolving ETSI ANSI and ITU standards 4 to 256 QAM Frequency Division Duplexing 1 RJ 45 10BASE T 100BASE TX Ethernet connection to either computer switch wireless access point 1 RJ 11 VDSL line to phone jack in the wall 1 RJ 11 Phone Line connect to phone 3 5 Watts maximum 12 VDC via AC power adapter Typical 350 mA Max 9 5 x 9 0 x 2 6 cm 3 74 x 3 54 x 1 02 in 140 g 4 94 07 Operating 0 50 C 32 122 F Storage 40 70 C 40 158 F 5 95 noncondensing POWER LINK VDSL LINK LAN ACTIVITY LAN SPECIFICATIONS 20 Standards Conformance Compliances IEEE 802 3 10BASE T IEEE 802 3u 100BASE TX IEEE 802 3x F
12. For Internet access the computer must be configured for TCP IP Power reguirements 12 VDC via the included AC power adapter Make sure that a properly grounded power outlet is within 1 8 m 6 ft of the CPE The CPE should be located in a cool dry place with at least 5 cm 2 in of space on all sides for ventilation Place the CPE out of direct sunlight and away from heat sources or areas with a high amount of electromagnetic interference The temperature and humidity should be within the ranges listed in the specifications Be sure that the CPE is also accessible for the UTP Ethernet and telephone cabling HARDWARE DESCRIPTION TigerAccess Extended Ethernet CPE The SMC7500A VCP is an external VDSL CPE product for high speed Internet access applications The device provides an Ethernet connection to a computer and an RJ 11 telephone jack for connection to a telephone The following figure shows the components of the TigerAccess Extended Ethernet CPE SMC O ver RJ 11 VDSL line port for connection to a RJ 45 Ethernet port VDSL switch via a wall for connection to a jack computer using LINK LINK Category 5 UTP cable e E a a LAN E N PHONE s ACTIVITY POWER RJ 11 phone port for connection to a telephone fax modem x DC 12V Power jack HARDWARE DESCRIPTION LED Status LED Status Description POWER On Power is being supplied to the CPE LINK On
13. Indicates a valid 10 100BASE TX LAN Ethernet link ACTIVITY Flashing Indicates that the CPE is transmitting or LAN receiving data on the Ethernet port LINK On Indicates that the VDSL line port has LINE established a valid link with a VDSL switch INSTALLATION Overview Before installing the CPE verify that you have all the items listed in the Package Checklist on page 5 If any of the items are missing ot damaged contact your local SMC distributor Also be sure you have all the necessary tools and cabling before installing the CPE Mounting The SMC TigerAccess Extended Ethernet CPE may be mounted horizontally on any flat surface such as a desktop ot shelf To mount the CPE simply stick the self adhesive rubber foot pads that come with this package on each of the 4 concave spaces located on the bottom of the device Place the device on the flat surface where it is to be installed INSTALLATION Cable Connections 10 AC Power Outlet Depending on the wiring configuration used in yout house separate wall jacks may be used for telephone and VDSL services Otherwise you will need to connect telephones and your computer directly to the CPE N 4 Computer SMC O remar O LINK LINK m e o L LINE asa Port un RJ 11 Ports a Category 5 UTP cable to PHONE Ethernet port on computer bd VDSL Line Wall Jack Standard Telephone Cable ACTIVITY POWER DC 12V
14. N 61000 4 8 1993 1 A m at frequency 50 Hz e Voltage dips short interruptions and voltage variations immunity test according to EN 61000 4 11 1994 gt 95 Reduction 10 ms 30 Reduction 500 ms gt 95 Reduction 5000 ms Warning Do not plug a phone jack connector in the RJ 45 port This may damage the device Les raccordeurs ne sont pas utilis pour le systeme t l phonique iv COMPLLANCES Safety Compliance Underwriters laboratories Inc USA Important Before making connections make sure you have the correct Cord Set Check it read the label on the cable against the following specification list Operating Voltage Cord Set Specifications 120 Volts UL Listed CSA Certified Cord Set Minimum 18 AWG Type SVT or SJT three conductor cord Maximum length of 4 6 m 15 ft Parallel blade grounding type attachment plug rated 15A 125 V 240 Volts Europe only Cord Set with HOSVV F cord having three conductors with minimum diameter of 0 75 mm IEC 320 receptacle Male plug rated 10 A 250 V Wichtige Sicherheitshinweise Germany 1 Bitte lesen Sie diese Hinweise sorgf ltig durch 2 Heben Sie diese Anleitung fiir den sp teren Gebrauch auf 3 Vor jedem Reinigen ist das Ger t vom Stromnetz zu trennen Verwenden Sie keine Fl ssi goder Aerosolreiniger Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung 4 Die Netzanschlu Bsteckdose soll nahe dem Ger t angebracht und lei
15. RRANTY WARRANTIES EXCLUSIVE IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE CUSTOMER S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN OUESTION AT SMC S OPTION THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF ITS PRODUCTS SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY IN NO EVENT WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE SHALL SMC BE LIABLE FOR INCIDENTAL CONSEOUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF ITS PRODUCTS EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE PO
16. SSIBILITY OF SUCH DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEOUENTIAL DAMAGES FOR CONSUMER PRODUCTS SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS SMC will provide warranty service for one year following discontinuance from the active SMC price list Under the limited lifetime warranty internal and external power supplies fans and cables are covered by a standard one year warranty from date of purchase SMC Networks Inc 38 Tesla Irvine CA 92618 COMPLIANCES FCC Class B This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference
17. TigerAccess Extended Ethernet CPE Extended Ethernet VDSL CPE High speed Internet access over existing phone lines Concurrent data and telephone services voice ISDN over a single connection Supports evolving ETSI ANSI and ITU VDSL standards for the copper local loop Supports power back off algorithm that permits a mixed distance deployment Fasy installation SMO User Guide Networks SMC75004 VCP Tiger Access Extended Ethernet CPE User Guide From SMC s Tiger line of feature rich connectivity solutions SMC Networks 38 Tesla October 2002 Irvine CA 92618 Part No 750 5871 Pub No 150000010900A R02 Phone 949 679 8000 Copyright Information furnished by SMC Networks Inc SMC is believed to be accurate and reliable However no responsibility is assumed by SMC for its use not for any infringements of patents or other tights of third parties which may result from its use No license is granted by implication or otherwise under any patent ot patent rights of SMC SMC reserves the right to change specifications at any time without notice Copyright O 2002 by SMC Networks Inc 38 Tesla Irvine CA All rights reserved Printed in Taiwan Trademarks SMC is a registered trademark and Tiger Access is a trademark of SMC Networks Inc Other product and company names are trademarks or registered trademarks of their respective holders LIMITED WARRANTY Limited Warranty Statement SMC Network
18. as an internal crossover MDI X the two pairs of wires must be straight through Straight Through RJ 45 Pin Assignments End 1 End 2 1 RD 1 TD 2 RD 2 TD 3 D 3 RD 6 TD 6 RDJ 16 CROSSOVER CABLE Crossover Cable If the twisted pair cable is to join two ports and both ports are labeled with an X MDI X or neither port is labeled with an X MDI a crossover must be implemented in the wiring Crossover RJ 45 Pin Assignments End 1 End 2 1 1D 3 RDH 2 TD 6 RD 3 RD 1 TD 6 RD 2 ID RJ 11 Ports Standard telephone RJ 11 connectors and cabling can be found in several common wiring patterns These six pin connectors can accommodate up to three wire pairs three telephone lines but usually only one ot two pairs of conductor pins and wires are implemented The RJ 11 ports on the side of the Tiger Access Extended Ethernet CPE contain two wire pairs an inner pair pins 3 and 4 and outer pair pins 2 and 5 On the LINE port the inner wire pair carries both voice and digital data On the PHONE port the inner wire pair carries voice only 17 TROUBLESHOOTING The outer wire pair is only connected if there is a second telephone line and carries voice only v O 23 52
19. cht zug nglich sein tn Das Ger t ist vor Feuchtigkeit zu sch tzen 6 Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Besch digungen hervorrufen 7 Die Bel ftungs ffnungen dienen der Luftzirkulation die das Ger t vor Uberhitzung sch tzt Sorgen Sie daf r daB diese ffnungen nicht abgedeckt werden 8 Beachten Sie beim Anschlu an das Stromnetz die Anschlu werte 9 Verlegen Sie die Netzanschlu leitung so da niemand dar ber fallen kann Es sollte auch nichts auf der Leitung abgestellt werden 10 Alle Hinweise und Warnungen die sich am Ger t befinden sind zu beachten 11 Wird das Ger t ber einen l ngeren Zeitraum nicht benutzt sollten Sie es vom Stromnetz trennen Somit wird im Falle einer berspannung eine Besch digung vermieden 12 Durch die L ftungs ffnungen d rfen niemals Gegenst nde oder Fl ssigkeiten in das Ger t gelangen Dies k nnte einen Brand bzw elektrischen Schlag ausl sen 13 ffnen sie niemals das Ger t Das Ger t darf aus Gr nden der elektrischen Sicherheit nur von authorisiertem Servicepersonal ge ffnet werden COMPLLANCES vi 14 Wenn folgende Situationen auftreten ist das Ger t vom Stromnetz zu trennen und von einer gualifizierten Servicestelle zu berpr fen anp e Netzkabel oder Netzstecker sind besch digt Fl ssigkeit ist in das Ger t eingedrungen Das Ger t war Feuchtigkeit ausg
20. ction icon for the adapter you want to configure 3 Highlight Internet Protocol TCP IP 4 Click on Properties 5 Select the option Obtain an IP address automatically and Obtain DNS server address automatically CONFIGURING THE TCP IP PROTOCOLS Mac OS 1 Pulldown the Apple Menu Click Control Panels and select TCP IP 2 Inthe TCP IP dialog box check Ethernet is selected in the Connect Via field 3 If Using DHCP Server is already selected in the Configure field your computer is already configured for DHCP Otherwise select Using DHCP Server in the Configure field and close the window 4 Another box will appear asking whether you want to save yout TCP IP settings Click Save Your service provider will now be able to automatically assign an IP address to yout computer 15 TROUBLESHOOTING Diagnosing CPE Indicators The TigerAccess Extended Ethernet CPE operation is easily monitored via the LED indicators to identify problems The table below describes common problems you may encounter and possible solutions If the solutions in the table fail to resolve the problem contact SMC Technical Support for advice Symptom Cause Solution POWER Power outlet e Check the power outlet by plugging in indicator does power cord or another device that is functioning not light up after external power properly POWELL
21. esetzt Wenn das Ger t nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen Das Ger t ist gefallen und oder das Geh use ist besch digt Wenn das Ger t deutliche Anzeichen eines Defektes aufweist 15 Stellen Sie sicher da die Stromversorgung dieses Ger tes nach der EN 60950 gepr ft ist Ausgangswerte der Stromversorgung sollten die Werte von AC 7 5 8V 50 60Hz nicht ber oder unterschreiten sowie den minimalen Strom von 1A nicht unterschreiten Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weniger TABLE OF CONTENTS TigerAccess Extended Ethernet CPE 1 Tatroduction iida T N SRA le ea Aa ett 1 VDSI Technology a s sade IN JN jala S YAMI vuos La 3 Features and Benefits stire nie 2 2232 a a a re 4 Package Checklist 40 49 un mi Sen a Se das na a 5 System Requirements xnveenneenneeseeenees 6 Hardware Description u a Sead ha eal a shes 7 TigerAccess Extended Ethernet CPE 0 00 7 LED Status ra radeon 8 Installation ti nz ae 9 OVERVIEW oir katus bt ls YAST KIT Lee En Der Aare E 9 Mounting rue ee tae ste a Masia eee ea ae a ne bare 9 Cable Connections Rein nn ema ase 10 Powertip On ans Soe aaa ee a a nee Da 11 Configuring the TCP IP Protocols 0 0 e eee eee eee 11 Troubleshooting he ema vatsa alu 14 Diagnosing CPE Indicators 2
22. low Control FCC Class B VCCI Class B CISPR Class B EN61000 3 2 3 EN 61000 4 2 3 4 5 6 8 11 CSA NRTL UL1950 CSA 22 2 950 TUV GS EN 60950 CNS 13438 Class B FOR TECHNICAL SUPPORT CALL From U S A and Canada 24 hours a day 7 days a week 800 SMC 4 YOU 949 679 8000 Fax 949 679 1481 From Europe 8 00 AM 5 30 PM UK Time 44 0 118 974 8700 Fax 44 0 118 974 8701 INTERNET E mail addresses techsupport smc com european techsupport smc europe com Driver updates http www smc com index cfm action tech support drivers downloads World Wide Web http www smc com http www smc europe com FOR LITERATURE OR ADVERTISING RESPONSE CALL U S A and Canada 800 SMC 4 YOU Fax 949 679 1481 Spain 34 93 477 4935 Fax 34 93 477 3774 UK 44 0 118 974 8700 Fax 44 0 118 974 8701 France 33 0 41 38 32 32 Fax 33 0 41 3801 58 Italy 39 02 739 12 33 Fax 39 02 739 14 17 Benelux 31 33 455 72 88 Fax 31 33 455 73 30 Central Europe 49 0 89 92861 0 Fax 49 0 89 92861 230 Switzerland 41 0 1 9409971 Fax 41 0 1 9409972 Nordic 46 0 868 70700 Fax 46 0 887 62 62 Northern Europe 44 0 118 974 8700 Fax 44 0 118 974 8701 Eastern Europe 34 93 477 4920 Fax 34 93 477 3774 Sub Saharian Africa 27 11 314 1133 Fax 27 11 314 9133 North Africa 34 93 477 4920 Fax 34 93 477 3774 Russia 7 095 290 29 96 Fax 7 095 290 29 96 PRC 86 10 6235 4958 Fax 86 10 6235 4962 Taiwan 886 2 2659 9669 Fax 886
23. of fiber optics and copper to provide high speed broadband Internet access VDSL s primary application is in providing a broadband data service to multi tenant residential or commercial buildings In this implementation fiber optic cable carries data from a telephone company s central office to the building then the installed telephone copper wires take the data and deliver it to individual units within that building a Telephone R AN Y Rooms Clients N RT De VDSLCPEN ON AW Telephone Fax Ne N 1 i W N 9 Rooms Clients NE amp amp VDSL CPE S Existing Phone gt Floor 1 Lines to Clients Local Servers VDSL Locally Hosted Services Ethernet Video Servers Billing Punch Down Concentrators Switch Blocks E Patch Panels ai ISP N or N q ber Opti Li Internet N Ethernet Fiber Optic Link to ISP D Links to Switch Telephone Line from Central Office Central Office PSTN Multi dwelling Multi tenant Building VDSL provides high speed Internet access over existing phone lines by making use of previously unused frequency bandwidth above the voice band By placing VDSL signals above the frequency of the voice signal a VDSL service can coexist on the same line with other telephone services VDSL can operate symmetrically providing the same data rate in both directions or asymmetrically providing a higher data rate in the
24. pstream at up to 1770 m 5800 ft The VDSL switch is typically located in a wiring closet or other central location of a multi dwelling multi tenant unit campus or enterprise An Internet connection is provided from the ISP to the customer s building ovet fiber optic cable running Ethernet directly over a 1 Gbps or future 10 Gbps connection This kind of WAN connection is referred to as Fiber To The Building FTTB Data signals entering a site are first passed through an Ethernet switch that segregates the signals for individual user connections and are then fed into the switch Phone signals are also routed from PBX MDF distribution equipment into the switch The data 1 TIGERACCESS EXTENDED ETHERNET CPE and phone signals for each user are combined in the switch and passed ovet VDSL lines to individual customers The SMC7500A VCP CPE at the customer end of the VDSL line connects to any PC or Macintosh eguipped with a 10 100BASE TX network interface card Your existing telephone modem or fax machine simply plugs into the CPE s phone port There is no need for special splitters terminators ot filters In fact there is no need to modify the home wiring at all and because the VDSL connection is based on Ethernet no further complex software configurations are required VDSL TECHNOLOGY VDSL Technology VDSL Very High Bit Rate Digital Subscriber Line is at the high end of the DSL technologies offering the best combination
25. rectly into a power outlet Check the LED marked POWER on the front panel to be sure it is on Configuring the TCP IP Protocols To connect the TigerAccess Extended Ethernet CPE to a computer through its Ethernet port the computer must have an Ethernet network adapter card installed and be configured for the TCP IP protocol Many service providers will configure TCP IP for client computers automatically using a networking technology known as Dynamic Host Configuration Protocol or DHCP Other service providers may specify an IP configuration known as a static IP address which must be entered manually Carry out the following steps to check that the computer s Ethernet port is correctly configured for DHCP 11 INSTALLATION 12 Windows 95 98 NT 1 Click Start Settings Control Panel 2 Click the Network icon 3 For Windows NT click the Protocols tab 4 Select TCP IP from the list of network protocols this may include details of adapters installed in your computer 5 Click Properties 6 Check the option Obtain an IP Address Windows 2000 1 Click Start Settings Network Dial up Connections 2 Click Local Area Connections 3 Select TCP IP from the list of network protocols 4 Click on Properties 5 Select the option Obtain an IP Address Windows XP 1 Click Start Control Panel Network Connections 2 Right click the Local Area Conne
26. s Inc SMC warrants its products to be free from defects in workmanship and materials under normal use and service for the applicable warranty term All SMC products carry a standard 90 day limited warranty from the date of purchase from SMC or its Authorized Reseller SMC may at its own discretion repair ot replace any product not operating as watranted with a similar or functionally eguivalent product during the applicable warranty term SMC will endeavot to tepair or replace any product returned under warranty within 30 days of receipt of the product The standard limited warranty can be upgraded to a Limited Lifetime warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller Registration can be accomplished via the enclosed product registration card ot online via the SMC web site Failure to register will not affect the standard limited warranty The Limited Lifetime warranty covers a product during the Life of that Product which is defined as the period of time during which the product is an Active SMC product A product is considered to be Active while it is listed on the current SMC price list As new technologies emerge older technologies become obsolete and SMC will at its discretion replace an older product in its product line with one that incorporates these newer technologies At that point the obsolete product is discontinued and is no longer an Active SMC product A
Download Pdf Manuals
Related Search