Pelco C2461M-A User's Manual
Contents
1. sse 5 Default Switch Settings and Location of Camera Adjustments 6 Dome and Trim Ring Installation ssssssssssseeeeteeeees 2 C2461M A 7 03 IMPORTANT SAFEGUARDS AND WARNINGS 1 Installation and servicing should be done only by qualified service personnel and conform to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 35 4 4X 6 or 6P enclosure it is designed for indoor use only and must not be installed where exposed to rain and moisture 3 Useonly installation methods and materials capable of supporting four times the maximum specified load 4 Use stainless steel hardware to fasten the enclosure to outdoor surfaces 5 To prevent damage from water leakage when installing an enclosure outdoors apply sealant around the bolt holes between the enclosure and mounting surface CAUTION Heater elements could be hot When camera power is on use caution when adjusting the camera REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that th2. INSTALLATION OPERATION 150 Series Camclosure Integrated Camera System with LowLight DSS Technology In Ceiling Mount C2461M A 7 03 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS 3 WERCOME 4 INSTALL THE BACK cete ice certet tete aan Aina ont REMOVE THE LOWER DOME INSTALL THE BACK BOX ettet betreten anih sd ATTACH DIRECTLY TO A WALL CEILING ATTACH TO A 4S DEEP ELECTRICAL BOX INSTALL IN A CEILING TILE INSTALL THE CAMERA MODULE sssseeennnnnnnnnnnnnnnnnn nnne nnne 8 CHECK HEATER JUMPER ie INSTALL AND POSITION THE CAMERA rtt net en enter g MAKE CAMERA SETTINGS iic iino th ttn tette ti tr ere itcm dede 10 ZOOM FOCU DIGITAL SEOW SHUTTER 055 ttt tton E AGC AUTOMATIC GAIN CONTROL BLC BACK LIGHT COMPENSATION VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLY HOW TO ADJUST THE PHASE CONTROL sees 12 VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT sss 12 REINSTALL THE DOME AND TRIM RING ssssseeeeenennnennnns 13 SPECIFICATIONS S serine tent iE rm epo ARE RR GERE 14 WARRANTY AND RETURN INFORMATION 15 LIST OF ILLUSTRATIONS Figure Page 1 Installation Directly to Wall Ceiling 2 Installation to 4S Deep Electrical Box 3 Ceiling Tile Installation sss 4 Heater Jumper and Camera Connector Locations
3. Connect the power wires Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one Camclosure system to the same ransformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the black wire on all units Failure to connect all of the units he same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras om TILE 8 32 X 1 25 E MOUNTING D NG SUPPLIED g f 2 Figure 3 Ceiling Tile Installation C2461M A 7 03 INSTALL THE CAMERA MODULE CHECK HEATER JUMPER The Camclosure is equipped with a heater to defrost the dome Some installations may not require this heater If the unit will never be subjected to a frost temperature you can disable the heater saving power requirements To disable the heater remove the jumper cover from the J1 jumper block refer to Figure 4 It is recommended that the jumper cover be left in the unit by installing it on one of the jumper pins CAMERA CONNECTOR JL Jl JUMPER Figure 4 Heater Jumper and Camera Connector Locations C2461M A 7 03 INSTALL AND POSITION THE CAMERA 1 Plugthe video connector from the camera into the mating connector inside the back box refer to Figure 4 2 Position the ca
4. the subject in the center of the picture appears dark or as a silhouette C2461M A 7 03 11 VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLY When using more than one camera power supply a brief vertical roll may occur on the monitor when a camera view is switched To eliminate vertical roll reverse the 24 VAC connections on one camera If both cameras are connected to the same transformer this should solve the problem If reversing the connections does not solve the problem adjust the phase control by synchronizing or line locking the cameras to one another How to Adjust the Phase Control It may be necessary to have two people in communication when synchronizing the cameras one person at the camera and another person at the monitor to observe the vertical roll and the effect of any adjustments made at the camera To synchronize the cameras 1 Choose a reference camera to which all other cameras will be phased 2 Select a camera and synchronize it to the reference camera by turning the phase adjustment control refer to Figure 5 clockwise and or counterclockwise 3 Each time an adjustment is made switch back and forth between the camera you are adjusting and the reference camera Repeat this process as many times as necessary until the roll between the cameras is no longer noticeable 4 Adjustthe phase of all other cameras by repeating steps 2 through 3 Always adjust to the reference camera selected in step 1 NOTE
5. RA Signal System Imaging Device Resolution Min Illumination Lens Synchronize Iris Control Signal to Noise AGG BLC Auto Iris Type Shutter Video Level CERTIFICATIONS NTSC Models PAL Models 12 VDC or 24 VAC 10 auto sensing 13 watts or less BNC 50 to 122 F 46 to 50 C De ices to 25 F 4 C Manual 360 pan 180 tilt Aluminum with steel camera mounting bracket and polycarbonate dome White polyester powder coat 1 75 H x 3 50 W inches 4 45 x 8 89 cm 2 42 H x 5 48 W inches 6 15 x 13 90 cm 3 75 inch diameter Indoor outdoor 1 70 Ib 0 77 kg NTSC PAL 1 3 inch interline transfer CCD 480 TV lines 0 75 lux 40 IRE DSS off f1 6 wide angle 1 20 lux 50 IRE DSS off f1 6 wide angle 0 025 lux 40 IRE 30 fields of DSS f1 6 wide angle 0 040 lux 50 IRE 30 fields of DSS f1 6 wide angle 2 6 6 0 mm or 4 0 9 0 mm varifocal D mount f1 6 Adjustable AC line lock internal auto select Electronic automatic 50 dB Selectable on off DIP switch selectable ON OFF DC drive 1 60 1 100 000 electronic auto Adjustable UL cUL and FCC Class B CE Class B UL cUL and FCC Class B Design and product specifications subject to change without notice C2461M A 7 03 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the dat
6. The preferred method for camera phase adjustment is to use a dual trace oscilloscope to align the vertical synchronization pulses of the reference camera to the selected camera s VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT To adjust the auto iris level turn the level adjustment counterclockwise to decrease the brightness and clockwise to increase the brightness level 12 C2461M A 7 03 REINSTALL THE DOME AND TRIM RING Place the trim ring and dome over the back box If the dome has a liner position the viewing window over the lens of the camera Tighten the tamper resistant screws with the supplied 1 8 inch hollow screwdriver bit Note that the screws are installed at an angle Figure 6 Dome and Trim Ring Installation Green materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment C2461M A 7 03 13 SPECIFICATIONS BACKBOX Electrical Input Voltage Power Consumption Video Connector General Operating Temperature Pan Tilt Adjustment Construction Finish Dimensions Above Ceiling Below Ceiling Bubble Environment Weight CAME
7. ber CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii If you are located outside the continental U S Alaska Hawaii Puerto Rico Puerto Rico Service Department Intermediate Consignee Ultimate Consignee Pelco American Overseas Air Freight Pelco 3500 Pelco Way 320 Beach Road 3500 Pelco Way Clovis CA 93612 5699 Burlingame CA 94010 Clovis CA 93612 5699 USA USA Pelco the Pelco logo Spectra Genex Esprit Camclosure and Legacy are registered trademarks of Pelco Copyright 2003 Pelco All rights reserved REVISION HISTORY Manual Date Comments C2461M 4 03 Preliminary manual for beta testing C2461M A 7 03 Final version C2461M A 7 03 15 PELCO World Headquarters 3500 Pelco Way Clovis California 933612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 Orangeburg New York Las Vegas Nevada Eindhoven Netherlands Wokingham United Kingdom Montreal Canada
8. e interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help C2461M A 7 03 3 Thank you for purchasing Pelco s Camclosure integrated camera system with LowLight DSS digital slow shutter technology Your new ICS150 Series in ceiling dome system includes a high resolution low light color camera with auto iris and varifocal lens The LowLight color camera has extended DSS settings to enhance the low light performance of the camera by automatically adjusting the number of fields of integration This slows the picture frame rate and increases the camera s sensitivity in low light conditions Prior to installation and operation of your new system thoroughly familiarize yourself with the information in this manual 4 C2461M A 7 03 INSTALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper resistant screws with the supplied 1 8 inch hollow screwdriver bit Remove the lower dome and place it t
9. e of shipment Exceptions to this warranty are as noted below Five years on Pelco manufactured cameras CC3500 CC3600 CC3700 and MC3500 MC3600 Series two years on all other cameras hree years on Genex Series multiplexers server and keyboard and 090 Series Camclosure Camera System wo years on 100 150 200 and 300 Series Camclosure Camera Systems wo years on all standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM6800E CM8500 CM9500 CM9740 CM9760 Matrix DF5 and DF8 Series Fixed Dome products wo years on Spectra Esprit and PS20 Scanners including when used in continuous motion applications wo years on Esprit and WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent reight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
10. e picture frame rate and increases the camera sensitivity under low light conditions Depending on the number of fields of integration the picture will develop a granular appearance and motion may show some lag resulting in a stereoscopic effect or streaking on fast moving objects These effects increase as the number of fields of integration increase Available settings include the following ON OFF LE 0552 pss 30 fields of integration maximum default setting 1 2 second scene update rate DSS2 DSS1 16 fields of integration maximum 1 4 second scene update rate Biss 4 fields of integration maximum 1 15 second scene update rate UN m 0552 m m 0852 1055 OFF Disables the DSS mode Digita slow shutter automatically adjusts the number of fields of integration depending on the light level of the viewed scene up to the maximum determined by the switch settings AGC AUTOMATIC GAIN CONTROL AGC automatically adjusts the image to compensate for changes in light levels ON Default setting Enables the AGC mode OFF Disables the AGC mode BLC BACK LIGHT COMPENSATION The BLC backlight compensation feature compensates for backlit scenes by enhancing objects in the center of the scene OFF Default setting Disables the BLC mode ON Enables the BLC mode Use this setting if a bright backlight is present and
11. e two 8 32 x 750 inch screws supplied 2 Connect the video cable 3 Connect the power wires Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one Camclosure system to the same transformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the black wire on all units Failure to connect all of the units the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras 4 Attach the back box to the adapter plate with the four 8 32 x 375 inch screws supplied 4S DEEP ELECTRICAL a OOO AAA NY T WALLOR 8 32 X 750 7 pi CEILING SUPPLIED ADAPTER PLATE E BACK BOX 8 32 X 375 screw I SUPPLIED Figure 2 Installation to 4S Deep Electrical Box 6 C2461M A 7 03 Install in a Ceiling Tile Refer to Figure 3 for the following steps 1 Cut hole 3 5 inches 9 cm in diameter in the ceiling tile for the back box Use the adapter plate as a template Punch four screw holes in the ceiling tile Use the four threaded screw holes in the adapter plate as a template Attach the back box to the ceiling tile and adapter plate with the four 8 32 x 1 25 inch screws supplied Replace the ceiling tile Remove an adjacent ceiling tile and connect the video cable
12. mera so that the tab on the camera bracket is pointing out of the enclosure away from the ceiling or wall Refer to the following illustrations for proper camera installation CAMERA BRACKET ALWAYS POINTS OUT OF THE TOP OF ENCLOSURE CAMERA CAMERA BRACKET TAB ALWAYS POINTS OUT OF THE ENCLOSURE Wall Mounting The camera bracket tab Ceiling Mounting The camera bracket tab points out of the enclosure and the top of the points out of the enclosure and the top of the camera points up towards the tab camera is pointed in the opposite direction 3 Install the camera bracket Gently squeeze the bracket place it against the shoulder inside the back box and gently release 4 Turn on power to the camera and monitor C2461M A 7 03 MAKE CAMERA SETTINGS CAUTION Heater elements could be hot When camera power is on use caution when adjusting the camera This applies to all models WHITE INDICATES SWITCH SETTING LEVEL PHASE ZOOM FOCUS wq gt Figure 5 Default Switch Settings and Location of Camera Adjustments ZOOM FOCUS 1 Select a field of view by turning the zoom adjustment ring clockwise counterclockwise Refer to Figure 5 2 Tighten the zoom locking screw 3 Adjust the focus by moving the focus locking screw clockwise counterclockwise 4 Tighten the focus locking screw 10 C2461M A 7 03 DIGITAL SLOW SHUTTER DSS Digital slow shutter slows th
13. o the side INSTALL THE BACK BOX The installation methods for the ICS150 back box include the following e Attach Directly to a Wall Ceiling e Attach to a 4S Deep Electrical Box e Install in a Ceiling Tile Select the best method for your installation and then refer to the following pages for instructions Attach Directly to a Wall Ceiling Refer to Figure 1 for the following steps 1 Cuta hole 3 5 inches 8 cm in diameter in the ceiling or wall using the adapter plate as a template 2 Connect the video cable 3 Connect the power wires Voltage Red Wire Black Wire 12 VDC t Ground 24 VAC AC Operation Only If you are wiring more than one Camclosure system to the same ransformer connect one side of the transformer to the red wire on all units and connect the other side of the transformer to the black wire on all units Failure to connect all of the units he same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras 4 Attach the back box to the wall ceiling SAN OR MOUNTING EE HARDWARE NOT SUPPLIED BACK BOK Figure 1 Installation Directly to Wall Ceiling C2461M A 7 03 5 Attach to a 4S Deep Electrical Box Refer to Figure 2 for the following steps The installation instructions assume that the 4S box was previously installed 1 Attach adapter plate to the 4S box with th
14. specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment PO number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization num
Download Pdf Manuals
Related Search