Panasonic WJ-GXD400 Operating Instructions
Contents
1. tion is correctly made and the cable is connected firmly The fan is not functioning because of the malfunction Contact your dealer Temperature inside the decoder is beyond the operating temperature range Use the decoder at appropriate ambient temperatures Aren t the fans on the rear or the ventilation slots of the decoder blocked When dust is collected around the fans or the ventilation slots clean it up When the ERROR indicator is blinking even when turning on the power of the decoder after leaving the decoder pow ered off for a while contact your dealer 10 12 A J Refer to the Check the status on the Camera page of the setup menu setup instruc tions PDF p Check the settings on the Basic page of the setup menu Refer to the setup instruc tions PDF Check the IP address subnet mask and default gateway of each of the decoder and the network cameras Refer to the setup instruc tions PDF The power cord insulation is damaged The power cord plug and con nectors get hot during use The power cord gets hot when bent or stretched No live image is displayed Check item Remedy Page The power cord plug and connectors are worn out This may result in electric shock or a fire Unplug the power plug from the AC outlet immediately and refer to qualified service personnel An error no2. Edition SP2 Microsoft Windows XP Professional SP2 Windows Internet Explorer 7 0 Microsoft Internet Explorer 6 0 SP2 210 W x 44 H x 307 D mm 8 27 W x 1 73 H x 12 09 D excluding rubber feet and projections Approx 2 0 kg 4 4 lbs 100 V AC to 240 V AC 50 Hz 60 Hz 12V DC 4 58A 120 mm W x 60 mm H x 35 mm D 4 72 W x 2 36 H x 1 38 D excluding the DC cable 0 35 kg 0 77 lbs When using this product without turning the power off Non voltage make contact input 50 kQ 5 V DC pull up 3 Open Collector output 24 V 100 mA maximum Standard Accessories CD ROM td t gp 1 pc Operating Instructions this book ooo 1 pc Warranty card NTSC model only cin 1 pc The CD ROM contains the operating instructions PDFs and the software The following are for installation AGA 1 pc Code label unid rore te ees 1 pc POWERCOO scudo duties 1 pc Use the power cord that is suited to your locality 20 26 Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis Alternatively in some countries you may be able to r
3. activity and or was obtained from a video provider licensed by MPEG LA to provide MPEG 4 Video No license is granted or shall be implied for any other use Additional information including that relating to promotional internal and commercial uses and licensing may be obtained from MPEG LA LLC See http www mpegla com GPL LGPL his product contains software licensed under GPL GNU General Public License LGPL GNU Lesser General Public License etc Customers can duplicate distribute and modify the Source code of the software under license of GPL and or LGPL Read the Readme txt file on the provided CD ROM for further information about the software Please note that Panasonic shall not respond to any inquiries regarding the source code 11 12 Major oper Front view ng controls and their functions Panasonic OPERATE ERROR1 ERROR2 ALARM e gt lt gt lt gt D Operation indicator OPERATE Lights when the power is on Important This indicator will blink for around a minutes until the unit becomes ready to operate t may take a few minutes more to complete it when the ambient temperature is O C 32 C or lower 2 Error 1 indicator ERROR1 Blinks to indicate any of the following Network link down err
4. interval may be longer depending on a network environment PC spec photographic subject access traf fic etc Location to install this unit To protect your network against unauthorized access install this unit within the security zone Avoid installing in the following locations Locations exposed to direct sunlight e Locations subject to strong magnetic field or radio waves e Locations subject to condensation as the result of Severe changes in temperature ocations subject to steam and oil smoke such as a kitchen Rack mounting e When mounting this unit use EIA equivalents 450 mm 17 3 4 or more depth e When operating the units keep the temperature inside the rack surely below 45 C 113 F Refer to page 19 for rack mounting Code label Unique IP address of your unit is marked on the code label Attach the code label on the CD ROM case etc to avoid losing Radio interference When the unit is used near TV radio antenna strong electric field or magnetic field near a motor or a transformer images may be distorted and noise sound may be pro duced MPEG 4 Visual patent portfolio license This product is licensed under the MPEG 4 Visual patent portfolio license for the personal and non commercial use of a consumer for i encoding video in compliance with the MPEG 4 Visual Standard MPEG 4 Video and or ii decoding MPEG 4 Video that was encoded by a consumer engaged in a personal and non commercial
5. 004 108 CE Vi deklarerar harmed v rt fulla ansvar f r att den produkt till vilken denna deklaration h nvisar r i verensst mmelse med standarddokument eller andra normativa dokument som framst lls i direktiv nr 2006 95 EC och 2004 108 EC Nosotros declaramos bajo nuestra nica responsabilidad que el producto a que hace referencia esta declaraci n est conforme con las normas u otros documentos normativos siguiendo las estipulaciones de las directivas 2006 95 CE y 2004 108 CE Ilmoitamme yksinomaisella vastuullamme ett tuote jota t m ilmoitus koskee noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja jotka noudattavat direktiivien 2006 95 EC ja 2004 108 EC s d ksi Noi dichiariamo sotto nostra esclusiva responsabilit che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive 2006 95 CE e 2004 108 CE Vi erkl rer oss alene ansvarlige for at produktet som denne erkl ringen gjelder for er i overensstemmelse med f lgende normer eller andre normgivende dokumenter som f lger bestemmelsene i direktivene 2006 95 EC og 2004 108 EC WARNING This apparatus must be earthed To prevent fire or electric shock hazard do not expose this apparatus to rain or moisture The apparatus should not be exposed to dripping or splashing and that no obj
6. Canadian ICES 003 NOTE This equipment has been tested and found to com ply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to pro vide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Caution To assure continued compliance example use only shielded interface cables when connecting to com puter or peripheral devices Any changes or modifications not expressly approved by the party responsible for compli ance could void the user s authority to operate this equip ment nt Safety Instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce h
7. ES OF MERCHANTABILITY FITNESS FOR ANY PAR TICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INAC CURACIES OR TYPOGRAPHICAL ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR THE IMPROVEMENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of Warranty IN NO EVENT SHALL MATSUSHITA ELECTRIC INDUSTRI AL CO LTD BE LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTE NANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIM ITATION DIRECT OR INDIRECT SPECIAL CONSE QUENTIAL OR EXEMPLARY ARISING OUT OF OR RELATING TO THE PRODUCT 2 PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER 3 UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFI CATION OF THE PRODUCT BY THE USER 4 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYS TEM COMBINED BY THE DEVICES OF THIRD PARTY 5 ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHO TOGENIC SUBJECT DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE CAMER A S PICTURE INCLUDING SAVED DATA FOR SOME REASON BECOMES PUBLIC OR IS USED FOR THE PURPOSE OTHER THAN SURVEILLANCE 6 LOSS OF REGISTERED DATA CAUSED BY ANY FAIL URE The network video decoder WJ GXD400 is designed to convert d
8. PCs and cameras page 20 Turn on the power of the decoder page 21 Change the TCP IP setting of the PC to conform to the set tings of the decoder Refer to the setup instructions PDF Perform the required settings on the setup menu to start operation Refer to the setup instructions PDF Images from the registered camera will be displayed Install the decoder in a rack Remove the rubber feet 4 pcs on the bottom of the unit Install the rack mounting brackets Option Refer to the following on both sides of the unit Using the mounting screws 4 pcs for the rack mounting brackets fix them firmly 1 When installing one unit Model No WV Q204 1S Rack mounting bracket Small x 1 Rack mounting bracket Large x 1 Bracket mounting screws M3 x 8 6 pcs 2 When installing two units Model No WV Q204 2S Rack mounting bracket Small x 2 Joint bracket x 3 Bracket mounting screws M3 x 8 6 pcs Bracket mounting screws Flat head M3 x 6 12 pcs Install the unit in the rack Using the rack mounting screws fix them firmly Important When operating the units keep the temperature inside the rack surely below 45 C 113 F Mount the unit into the rack with a space equivalent to approx 1 unit 44 mm or more to separate from other devices To prevent the unit from overheating do not block the ventilation openings or slots in the cover Be sure to keep the temperature in
9. Panasonic Installation Guide Network Video Decoder Model No WJ GXD400 HIGH DEFINITION MULTIMEDIA INTERFACE Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use No model number suffix is shown in this manual We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives 2006 95 EC and 2004 108 EC Wij verklaren als enige aansprakelijke dat het product waarop deze verklaring betrekking heeft voldoet aan de volgende normen of andere normatieve documenten overeenkomstig de bepalingen van Richtlijnen 2006 95 EC en 2004 108 EC Wir erkl ren in alleiniger Verantwortung daf das Produkt auf das sich diese Erkl rung bezieht mit der folgenden Normen oder normativen Dokumenten bereinstimmt Gem den Bestimmungen der Richtlinie 2006 95 EC und 2004 108 EC Vi erklarer os eneansvarlige for at dette produkt som denne deklaration omhandler er i overensstemmelse med standarder eller andre normative dokumenter i f lge bestemmelserne i direktivene 2006 95 EC og 2004 108 EC Nous d clarons sous note seule responsabilit que le produit auquel se r f re la pr sente d claration est conforme aux normes ou autres documents normatifs conform ment aux dispositions des directives 2006 95 CE et 2
10. When displaying smaller images on a larger screen area e g displaying VGA images on a 4VGA screen area the images are enlarged to fit to the screen size e It is not possible to display larger images on a smaller screen area i e displaying 4VGA images on a VGA screen area Outline of the functions Live image display Live images can be displayed on a high definition monitor 1 920 x 1 080 using the HDMI connector Live images from up to 6 cameras with the image capture size of VGA 640 x 480 can be displayed simultaneously Displaying of live images from a single camera with the image capture size of 4VGA 1 280 x 960 is also available It is possible to simultaneously display JPEG images and MPEG 4 images on the same monitor It is also possible to connect and display live images on an analog monitor NTSC PAL O Audio output Audio G 726 from a single camera among the cameras of which images are being displayed on a screen can be heard Audio output is available via the HDMI output connector or the audio output connector RCA pin jack Refer to the setup instructions PDF for how to output images video and audio 17 18 Operation flow Setup procedure The operation flow of the decoder is as follows Connections Startup Network settings of a PC Setup Start operation Install the decoder in the rack page 19 Go to step 2 when not installing in the rack Connect
11. a P R 00985 809 750 4300 O 2008 Matsushita Electric Industrial Co Ltd All Rights Reserved For European and other fields Matsushita Electric Industrial Co Ltd Osaka Japan http panasonic net Importer s name and address to follow EU rules Panasonic Testing Centre Panasonic Services Europe GmbH Winsbergring 15 22525 Hamburg F R Germany NM0608 1068 3TROO5589BAA Printed in Japan
12. dapter to a 120 V AC 60 Hz for NTSC model 220 240 V AC 50 Hz for PAL model The OPERATE indicator will start blinking for around a minute just after turning on the power of the decoder It will stop blinking and light steadily when the decoder becomes in operation status Default screen When the power of the decoder is turned on or when the decoder is rebooted images from the camera channel selected in advance will automatically be displayed It is necessary to configure the Default screen setting in advance A black screen will be displayed when No output is selected for Video Audio output settings for the default screen e Audio from the camera can be heard when On is selected for Audio output When other than 1 screen is selected for Screen pattern audio from the camera to be displayed on a screen at the upper left corner will be heard e When using a camera that does not have the micro phone input function audio will not be heard even when On is selected for Audio output Turn off the power of the decoder To shut down the decoder do the following Detach the power plug from the outlet The OPERATE indicator on the decoder will go off Important Detach the plug from the outlet if not operating the decoder for a length of time e When the decoder has not been used for a certain peri od turn on the power of the decoder approximately once a week and operate the decoder to prevent inter
13. eat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over ZA 83125A 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Limitation of Liability THIS PUBLICATION IS PROVIDED AS IS WITHOUT WAR RANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WAR RANTI
14. ects filled with liquids such as vases should be placed on the apparatus All work related to the installation of this product should be made by qualified service personnel or system installers The connections should comply with local electrical code CAUTION Before attempting to connect or operate this product please read the label on the bottom RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magni tude to constitute a risk of electric shock to persons triangle is intended to alert the user to the presence of important operating and mainte nance servicing instructions in the litera ture accompanying the appliance The exclamation point within an equilateral The serial number of this product may be found on the sur face of the unit You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft Model No Serial No For U S A For Canada This Class A digital apparatus complies with
15. enneenn rennen nnne nnns 20 Turn on off the power of the decoder 00 02 eeseeeeeenceeeeeeeeeeeeeeeeeaeeneneneesseeeeeeeanenenaneeseneesssaeesenaneesesneesennetes 21 Turn on the power of the decoder sesssssseeeeseeeeeeeeeene nenne nennen nennen enne nennen 21 Turn off the power of the decoder ssssssssssssssssseeneenee nn nro rca 21 TroubleshotiN gk E ad 22 Specifications il rm RD IUE 24 Standard Aecessories m oda ele ciere tel ee a ee ae ee 25 Precautions Do not block the ventilation opening or slots on the cover To prevent the apparatus from overheating place it at least 5 cm 2 inches away from the wall Do not drop metallic parts through slots This could permanently damage the apparatus Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble the apparatus To prevent electric shock do not remove screws or covers There are no user serviceable parts inside Contact qualified service personnel for maintenance Do not expose the apparatus to water or moisture Do not try to operate it in wet areas Take immediate action if the apparatus gets wet Turn the power off and refer servicing to qualified service personnel Moisture can damage the apparatus and also cause electric shocks Built in backup battery Before the first use charge the built in backup battery lithium battery by turning on the power for 48 hou
16. eturn your products to your local retailer upon the purchase of an equivalent new product mmm Disposing of this product correctly will help health and the environment which could othe for further details of your nearest designated collection point o save valuable resources and prevent any potential negative effects on human rwise arise from inappropriate waste handling Please contact your local authority Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment p ease contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal 2 For U S Canadian and Puerto Rican fields Panasonic System Solutions Company Unit Company of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way 2H 2 Secaucus New Jersey 07094 Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Canada 905 624 5010 http www panasonic ca Panasonic Sales Company Division of Panasonic Puerto Rico Inc San Gabriel Industrial Park 65th Infantry Ave KM 9 5 Carolin
17. ferences with functions 21 22 Troubleshooting Check the following before requesting repair Contact a dealer if a problem cannot be solved even after checking and trying the solution or if a problem is not described below or when having a problem with installations Check item Remedy Page Power is not turned on The decoder does not start up even by turning on the power The error 1 indicator ERROR is blinking NW link error The error 2 indicator ERROR is blinking FAN error The error 2 indicator ERROR2 is blinking Thermal error The error 2 indicator ERROR2 is blinking Network camera error detec tion Network camera error detec tion audio Is the connector plug of the AC adapter connected to the power connector DC12V IN of the decoder firmly s the power plug of the AC adapter connected to the outlet firmly s the power cord connected to the AC adapter firmly A sn Are the mode switches positioned correctly Make sure that all the switches are in the OFF position Is the LAN cable 100BASE TX 1 000BASE T firmly con nected to the network port Confirm the cable is firmly con nected ss Oo eee eee EE Is the LINK ACT indicator lit When it is not lit connection to a LAN is not established or a network is not working correctly Confirm that the connec
18. igital image data JPEG MPEG 4 to analog video signals By connecting to a network LAN images and audio from cameras and encoders connected to the network can be displayed on an HDMI monitor or on an analog monitor NTSC PAL e Up to 6 cameras can be displayed on a single monitor by using the HDMI connector or the BNC output connector NTSC PAL One 1 x AVGA 1 280 x 960 image with 2 x VGA 640 x 480 images or 6 x VGA 640 x 480 images can be displayed in a split screen Images audio and the other data packets can be received via a network About The Operating Instructions There are 2 sets of operating instructions for the WJ GXD400 as follows Installation Guide this book Setup Instructions PDF The Installation Guide contains descriptions of how to install and connect this unit Refer to the Setup Instructions PDF on the provided CD ROM for descriptions of how to perform the unit settings Adobe Reader is required to read these operating instructions PDF Software License Licence This product includes a software component that is licensed by GNU General Public License GPL or GNU Lesser General Public License LGPL For more details refer to the Readme txt file in the CD ROM System Requirements for a PC CPU Pentium 4 3 0 GHz or faster Memory 1 GB or more 512 MB or more is required when using Microsoft Windows XP Network Interface 100 1000 Mbps Ethernet port x1 Monitor Image captu
19. model category 7 straight Cable is not provided Audio output connector AUDIO OUT Connect an audio device such as an amplifier speaker etc 3 Video output connector VIDEO OUT Connect a video device such as a monitor 4 SIGNAL GND terminal Connect this terminal with the SIGNAL GND terminals of the devices in the system for signal ground When oper ating the decoder and the devices in the system without signal ground oscillation or noise may be produced 5 HDMI connector Connect an HDMI monitor 6 Alarm Control terminals ALARM CONTROL Connect an external device or an alarm device such as a buzzer or a lamp When connecting an external device first remove 9 mm 10 mm of the outer jacket of the cable and twist the cable core to prevent a short circuit Output 123812 000000 Input Approx 9 10 mm Specification of cable wire AWG 22 28 Single core twisted Important e Do not connect 2 or more wires directly to a terminal When it is necessary to connect 2 wires or more use a splitter lt Ratings gt e Alarm reset input IN 1 Non voltage make contact DC 4 5 V internal pull up e GND G e Alarm output OUT 2 Open collector output Maximum applied voltage 24 V DC 100mA e Error output OUT 1 Open collector output Maximum applied voltage 24 V DC 100mA NC Do not use IN 2 OUT 3 2 Power connector DC12V IN Con
20. nect to the provided AC adapter Do not connect other than the provided AC adapter Cable clamp Fix the cable of the provided AC adapter Cable clamp Cable clamp 13 14 Setup window and live image display O Setup window Launch a web the browser Enter the IP address set to the decoder in the address box and press the enter key Refer to the setup instructions PDF for further information about the operation window 1 Setup menu buttons 2 Setup page Live image display 1 Image display area 2 Information display area Information of the detected alarm or error will be displayed 3 Time amp date display area The current time of the decoder s clock will be displayed O Border It is possible to apply a color on the frame border that divides a screen Select a color from the following Off White Gray Black Setup instructions PDF O Alarm display When an alarm occurrence is detected the frame border will turn red to indicate which images are from the alarm camera The ALARM indication will also be displayed When an alarm occurred time and date of the alarm occur rence information about the alarm source will be displayed Screen Pattern It is possible to display images from up to 6 cameras on a screen 1 screen 3 screen and 6 screen are available to display images from cameras 1
21. or 3 Error 2 indicator ERROR2 Blinks to indicate any of the following Thermal error Cooling fan error Network camera error 4 ALARM indicator Lights when an alarm is detected received LINK ACT indicator Lights when the network connection is established Blinks when data packets are being transmitted received 100 BASE TX indicator Lights when the decoder is connected to a network at 100 BASE TX 1000 BASE T indicator Lights when the decoder is connected to a network at 1000 BASE T Reset switch Press this button to reboot the decoder SSeS Mode switches Not be used normally Make sure that all the switches are in the OFF position before starting operation ON OFF Maintenance port Use this port to connect directly to a PC and perform maintenance operations Do not use for normal operation Note e When connecting with a PC directly use the straight cable Rear view SIGNAL OTT BND M XX XX XX XX XX XX e 0 DM O hd o 1000EASE T AUDIO OUT VIDEO OUT 100B2 SE TX faecia 0000000 EXE 4 CD Network port Connect a LAN cable 100BASE TX 1 OOOBASE T NTSC model category 5e straight PAL
22. re size 1 024 x 768 pixels or more Color 24 bit True color or better OS Microsoft Windows Vista 32 bit Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 OS Language English Web Browser Microsoft Internet Explorer 6 0 SP2 Windows Internet Explorer 7 0 Other CD ROM Drive It is necessary to read the operating instructions on the provided CD ROM Adobe Reader It is necessary to read the operating instructions on the provided CD ROM Notes When using a PC that does not meet the above requirements displaying of images may become slow or the web browser may become inoperable Trademarks and Registered Trademarks e Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Microsoft Windows Windows Vista Internet Explorer ActiveX and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and other countries ntel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries HDMI HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC Other names of companies and products contained in these operating instructions may be trademarks or registered trade marks of their respective owners Copyright Distributing cop
23. rs or more If it is not charged enough in a case where the power goes down the internal clock may keep bad time or the operative condition may be different to that before the electric power failure The built in battery life is approximately 5 years as an indication of replacement This is just an indication of replacement We are not providing any guarantee of the built in battery lifetime Replacement cost of the built in battery is not covered by the warranty even if it needs to be done within the warranty period Ask the shop where you purchased the unit when replacement of the battery is required Use this product for indoor use only Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air condition er Otherwise it may cause deformation discoloration and malfunction Keep this product away from water To continue using with stable performance e Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations sub ject to high temperatures and high humidity Do not expose the product to direct heat such as from a heater e Use this product at temperature within 5 C to 35 C 41 F to 95 F and humidity below 90 When using this product without turning the power off The input power source for this apparatus is 100 V AC to 240 V AC 50 Hz 60 Hz Use only the supplied power cord Use the power cord that is suited to
24. screen display 6 screen display O Information display on each screen live image display The following information can be displayed according to the settings Information display area 3 Optional info Information about the sequence display will be dis played When the sequence display is triggered by a schedule a sequence number will be displayed 4 Camera title The camera title will be displayed When Off is selected for camera title it will not be displayed Note e Information display position and display or hide infor 1 Screen ID mation display can be determined by configuring the settings on the setup menu e When the Image capture size setting is other than QVGA VGA or 4VGA a black screen will be dis played The screen ID will be displayed 2 Time amp date display area Time and date of the camera s clock will be displayed Time and date of the camera s clock will be displayed when stream data from the camera contains time and date information 15 16 Display mode There are 2 display modes Full screen mode full resolution display and the Trimmed screen mode trimming mode Normally select Full screen When the displayed images do not fit in the screen even by adjusting the display settings of the monitor in use select Trimmed screen In the Trimmed screen mode however images to be displayed in each screen will also be trimmed Notes e
25. side the rack below 30 C 86 F when operating the units Installing venti lation fan s in the rack is recommended especially when the rack is covered with front lids Remove the rubber feet Bracket mounting Screws Rack mounting bracket Small Rack mounting bracket Large Joint bracket Remove two screws at the rear side and fix the brackets with bracket mounting screws Flat head M3 x 6 Rack mounting bracket Small H n Rack mounting bracket Small Bracket mounting Flat head screws screws Rack mounting screws 19 Connections When connecting to a network using a hub When connecting the decoder to a network using a hub use a LAN cable Network camera Hub AGE DNONONCNONCNONONCNONO 5 OO OOOO ud LJ Ll 6 LAN cable category 5e straight NTSC model category 7 straight PAL model Monitor L J 18 aF p To an outlet AC adapter standard accessory Important Use a switching hub or a router which is compliant with 100BASE TX 1000BASE T Power supply is required for each decoder 20 Turn on off the power of the decoder Turn on the power of the decoder Insert the power plug of the AC adapter to an outlet Connect the power plug of the AC a
26. t your network against leakage or theft of information including authentication information user names and passwords and DDNS server information CONTENTS Important Safety Instr cti ris ai 4 Limit tion of Liability eI e REIR LL ni apa ERE Ue ciui o eb eed ive ds 5 Disclaimer ot Warranty 3 iii t e E E p E OD RO ED EO DAE I ERE REF ner REA eds 5 Preface vomitar nob Ba agn Giada on ee A eed ae adis 6 Features ou bee e i Un MEI OMESHER I REM ES 6 About These Operating Instructions ssssssseeeeeeeeennen nene nnne nnne nnne nens 7 Software License Licence nui olera EB ena HERO era 7 System Requirements for a Plica eee e EE Let ae Bede indue dodo 7 Trademarks and Registered Trademarks oooconnccccnonccononcccnoncnnnnonnonanonnnnonnnnnnn no rnnn eene nnne 8 Copyright e 8 Network Security ias as ADU po RE It e dle dd ce 8 PfeCcautioris 5 pn nene ituda d aiite ar pete uncut 10 Major operating controls and their functions essnnnnnenm m emere nenne 12 Front view Rear view Setup window and live image display ssssesesssseeeeeeeneeeeenneennen nnnm 14 Quitline of the f nctioris 5 e o PRU He d RD t HEU REOR SERIE 17 Operation flow week genu m Et a ade See ele a 18 Setup procedures roca ase P ARAM RI Hei A INS 18 Install the decoder in a rack apa ae ei tr eee 19 CONNECTIONS OO 20 When connecting to a network using a hub sesssseeeneneeenme
27. tification message is displayed Check the displayed message and contact the system administrator Images from cameras may not sometimes be displayed when receiving MPEG 4 images via the Internet Check the settings of the router or other network devices Contact the network administrator Check the following settings of both the decoder and the network cameras IP address Subnet mask Default gateway 23 24 Specifications Network Video Decoder Power source Power consumption Ambient temperature Ambient humidity Video output connectors Audio output connector Parallel port Resolution Image compression method Audio compression method Protocol Network Security OS Browser Dimensions Weight AC Adapter Power Source Output voltage Output current capacity Dimensions Weight 12 V DC 1 4 A using the supplied AC adapter Approx 17 W 10 C to 50 C 14 F to 122 F Less than 90 NTSC model HDMI x 1 1 V P P 75 Q BNC x 1 PAL model HDMI x 1 1 V P P 75 Q BNC x 1 Line level 600 Q unbalanced x 1 RCA pin jack Alarm reset input x 1 2 Alarm output x 1 3 Error output x 1 3 640 H x 480 V 320 H x 240 V 1 280 H x 960 V selectable JPEG MPEG 4 G 726 HTTP RTP TCP IP UDP IP DHCP DNS DDNS NTP 100BASE TX 1 OOOBASE T RJ 45 connector Password Microsoft Windows Vista Business 32 bit Microsoft Windows XP Home
28. ying disassembling reverse compiling reverse engineering and also exporting in violation of export laws of the software provided with this product is expressly prohibited This product incorporates copy protection technology that is protected by U S and foreign patents including patent numbers 5 315 448 and 6 836 549 and other intellectual property rights The use of Macrovision s copy protection technology in the product must be authorized by Macrovision Reverse engineering or disassembly is prohibited Network Security As you will use this product connected to a network your attention is called to the following security risks eakage or theft of information through this product Use of this product for illegal operations by persons with malicious intent nterference with or stoppage of this product by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks Use this product in a network secured by a firewall etc e f this product is connected to a network that includes PCs make sure that the system is not infected by computer viruses or other malicious entities using a regularly updated anti virus program anti spyware program etc Protect your network against unauthorized access by restricting users to those who log in with an authorized user name and password Apply measures such as user authentication to protec
29. your locality Handle the appliance with care Do not strike or shake as this may damage the product Failure to observe this may cause trouble About the monitor When displaying the same image on the monitor for a long time the monitor may be damaged When an error is detected the unit will restart automati cally This unit will restart when detecting an error caused by any reason The unit will be inoperable for around 1 minute after the restart just as when the power is turned on About the self diagnosis function When the unit malfunctions due to exogenous noise etc for 30 seconds or more the unit will automatically reset and will return to normal state When the unit is reset initializa tion will be carried out as when the power of the unit is turned on When the unit repeatedly resets exogenous noise level around the unit may be high and that may cause malfunction Contact your dealer for instructions Cleaning Turn the power off when cleaning the unit Otherwise it may cause injuries Do not use strong or abrasive detergents when cleaning the apparatus body Use a dry cloth to clean the apparatus when it is dirty When the dirt is hard to remove use a mild detergent and wipe gently Distributing copying disassembling reverse compil ing reverse engineering and also exporting in violation of export laws of the software provided with this prod uct is expressively prohibited Refresh interval The refresh
Download Pdf Manuals
Related Search