Newcon Optik TVS 7B User's Manual
Contents
1. Head Gear turn the ring counter clockwise until it stops Press the button in the middle of this ring and insert the mounting adapter sledge into the mounting slot of the Device Now you can re lease the button Set the Device in the most comfortable for Operator po sition tighten the ring by turning it clockwise until it stops Adjust and tighten all straps around the head and under the chin to reach more convenient and stable state of the device To flip up the Device simply press the rotation enabling button and turn the device to the top posi tion The mounting bracket can be removed from the Head Gear and mounted to the helmet as well TVS 7B can be used with snap on 50 mm lenses which increases magnification and operating range Before attaching snap on lens re move protective cover ring from the existing lens of the TVS 7 INTRODUCTION Thermal Imaging Binoculars TVS 7B enable the profes sional users to visualize a heat irradiated by live bodies targets and other objects Device detects extremely low difference in temperature thus distinguishing the object image from its background Unlike the conventional night vision equipment which requires minimum light or supporting illumination and might not always be effective in smoky or foggy environ ment TVS 7B needs no light to operate and generates high quality image in the harsh weather conditions The camouflage doesn t help to obscu2. Rings Interpupillary adjustments between eyes Slide lt gt or gt lt O ON AO BRWN External Power Pack Very convenient for long time or cold weather operation Comes with high capacity Li lon batteries and universal charger Good for up to 8 hours of continuous work Caution When external battery pack is in use strictly recommended to remove 2 pcs of AA batteries from battery compartment Leaving them inside will cause overheating of the device and or batteries which would cause batteries leakage and power drain from the exter nal battery pack Battery Pack has red LED which is ON when connected to TVS 7B Universal l10 250 V charger is included IMPORTANT NOTICE USE OF IMPROPER BATTERIES OR VOLTAGE MAY SERIOUSLY DAMAGE DEVICE WITH NO WARRANTY COVERAGE FROM US How To Do IT This is the short description how to operate TVS 7B Read carefully to make sure you fully understand how to power up your Thermal Imager properly TVS 7B needs minimum 2 4 V and Maximum 3 3 V therefore Use only Lithium type 2 pcs AA batteries 1 5V each or at least 2500 mAh Rechargeable batteries AA size 1 2V each To begin with install batteries into battery compartment 8 complying with polarity guidance inside outside Remove cover from the front lens and switch Power But ton into position ON Clicking sound in the beginning of usage is normal for thermal core By turning and moving Dioptric Adjustment rings 9 adjust di
3. This Product made by Newcon Optik 105 Sparks Ave Toronto Ontario M2H 2S5 Canada Tel 1 416 663 6963 Fax 1 416 663 9065 www newcon optik com E mail newconsales newcon optik com Export Information Night Vision and Thermal Imaging Equipment in general is subject to export control Please consult your Local and Federal Government Authorities prior to purchase or further shipment of the Controlled Goods Newcon Optik relieves itself from any liabilities claims or accusations if its equipment is found in certain destinations without proper Export Documentation Newcon Optik under NO circumstance will illegally export 2010 NEWCON OPTIK OPTIK THERMAL IMAGING OPTICAL DEVICES Basic User s Manual THERMAL IMAGING BINOCULARS GOGGLES TVS 7B Dear Customer This Manual is a basic instruction on operating the Thermal Imaging Device TVS 7B We assume that an operator has a knowledge in principle on use of electro optical systems However if you find any difficulties in operating device please 1 Read this Manual thoroughly to make sure that you understand completely its instructions and warnings 2 Contact our Technical Support Service via phone fax e mail We hope that you will enjoy our Products Thank you NEWCON OPTIK Specifications of TVS 7B Sensor Type Detector Display s Resolution Output Resolution Thermal Sensitivity Spectral Response Focal Length Field of View Lens t
4. opters and dis tance between eyepieces to satisfy the user eyes visual acuity for the system s best performance Observing the object adjust focus by turning front lens 6 With optional Video Out to USB adapter and soft ware the video signal from Thermal Imager can be trans ferred to the computer and stored for tactical purposes Video Out cable Allows to connect TVS 7B to any standard RCA Video In monitor TV VCR etc Video Out to USB adapter and software Allow to transfer images into digital format for further transfer to a computerized fire control system NOTE All technical description and features of the product are subject to change without prior notice F a Wada DO NOT POINT THE TURNED ON DEVICE TO THE BRIGHT LIGHT SOURCE IN SOME CASES LIGHT OVERLOAD MAY CAUSE IRREVERSIBLE REDUCTION OF lI T OR F P A RESPONSIVITY OR PERMANENT DAMAGING
5. re a hiding body as TVS 7B detects body s heat through Thermal imager is powerful tool for tactical surveillance and scene assessment applications Its small size light weight and convenient bi ocular design make TVS 7B simple and effective in operation Law enforcement pub lic safety service and other professional users can use the system to conduct hidden compartment searches pe rimeter surveillance marine or ground surveillance safer flights structure profiling activities fugitive and rescue searches disturbed surface investigations pollutant searches and vehicle pursuits In fire and rescue applica tions thermal imaging is used to conduct scene size up in fire attack search and rescue hazmat assessments and post fire overhaul TVS 7B can be used as hand held Thermal Imager Bin oculars or head helmet mounted Goggles Detection range depends on various factors like outside temperature size of object type of lens used etc Universal Service Connector allows connecting TVS 7B to video cable enclosed or to external battery pack optional DESCRIPTION ON OFF Power Button Switch Left amp Right Eyepieces with Rubber eyecups Manual Brightness Control override of displays Digital Zoom Button Switch Universal Service Connector see details on page 4 Front lens with Focusing Ring Black hot white hot Button Switch BH VWH Battery Compartment Cover Dioptric Adjustment
6. se abused mishandled or subjected to unauthorised repairs NEWCON disclaims any other warranties either expressed or implied except as expressed herein The sole obligation of NEWCON is to repair or replace the covered device NEW CON expressly disclaims responsibility for any lost profits general specific direct undirect or consequential damages which may result from breach of any warranty or resulting from the use or inability to use any NEWCON s product Do not return merchandise directly to NEWCON without expressed permission of our Customer Service Representative who has to issue a Return Authorisation Number RA NEWCON accepts No responsibility for unauthorised returns All items returned for exchange upgrade repair service etc must be with all accessories in original packaging shipping and insurance cost prepaid both ways Items received by NEWCON without RA missing parts or accessories or damaged due to inadequate packaging or customer s abuse i e scratched cracked body burned IIT FPA or broken lens will be returned back to customer or repaired for the cost FPA Ser No Housing Ser No HEAD GEAR ROTATION ENABLING BUTTON BUTTON RIN MOUNTING ADAPTER TVS 7B ATTACHED TO HELMET MOUNT TVS 7B is a self contained system designed for use as binoculars hand held operation or goggles head Helmet mounted The Head Gear is furnished with flip up mechanism To set and adjust the
7. ype Video Output Water Resistant Power Supply Battery size Weight Microbolometer TI 3620as Uncooled Amprhpous Silicon 640 x 480 640 x 480 lt 100 mk 7 14 um 25 mm I x 8 degrees Germanium NTSC Yes 2 5 3 3V Lithium rechargeable AA 450 gr Manufacturer s Warranty Newcon Optik warrants it s Optical Products against genuine manufacturer s defects in materials and workmanship for a period of one full year from the original date of purchase All optical electronic parts components which used in covered products such as image intensifier tubes focal plain arrays thermal cores are covered by their original Manufac turer s warranty Any device returned for warranty service or repair must be judged by Newcon s Technical Control Department as having been used accordingly its original design intents As such misuse neglect or any abnormal use is not covered by this warranty Product s malfunction or deterioration due to normal use is not covered by this warranty NEWCON will repair or replace such products or parts which upon inspection by TCD is found to be defective in either materials or workmanship As a condition of NEWCON obligation regarding a warranty work the product must be returned to the place where it has been purchased with satisfactory proof of purchase sales invoice must be presented This warranty is null and void if equipment has been altered tampered with modified or otherwi
Download Pdf Manuals
Related Search