Magnadyne MKE-300 User's Manual
Contents
1. For Technical Assistance call 800 638 3600 or visit www magnadyne com until the onboard LED turns on for 2 seconds and the beeper responds with a confirming chirp indicating the signal has been stored into memory 4 If you have additional transmitters up to 4 that need to be programmed repeat step 3 for each transmitter Exit Turn the ignition switch to the OFF posi tion or leave it for 15 seconds The onboard LED turns off and the beeper will emit 3 long chirps to confirm exit B 4 Button Transmitter Programming Does not apply to MKE 100 Note This mode will only retain the last 4 remote transmitters programmed If the transmitter mem ory is exceeded the security system will start deleting transmitters from memory in chronologi cal order 1 Enter the program code 12345 on the key pad The beeper will emit a long chirp to confirm the correct code was entered 2 Enter a new 4 to 6 digit user code on the key pad Do not use 1234 3 Finish by pressing the LOCK key on the key pad 1 long beep with 2 short beeps will confirm the new user code has been stored into memory 4 If you have additional user codes up to 4 that need to be programmed repeat steps 2 3 for each new user code Exit Press and hold the LOCK key for 1 sec ond or if 15 seconds of inactivity occurs during the above steps the unit will revert back to the last successfully stored code 3 longs beeps confirm exit A 4 B2. MAGNADYNE User s Manual Keypad Keyless Entry System Transmitters Press Simultaneously to Turn On Off Porch Light Locks All Doors Unlocks Entry Locks All Doors Unlocks Entry Including Cargo Doors Including Cargo Doors Turns On Off Locks All Unlocks All Porch Light 95 Cargo Doors Cargo Doors O Programming A 3 Button Transmitter Programming 1 Turn the ignition switch to the ON position Does not apply to MKE 100 within 15 seconds Note This mode will only retain the last 4 remote transmitters programmed If the transmitter mem ory is exceeded the security system will start deleting transmitters from memory in chronologi 2 Push the Program switch 5 times the onboard LED will be flashing and the beeper will emit a long chirp to indicate the system is in Transmitter Programming mode OCLC eH cal order 1 Turn the ignition switch to the ON position within 15 seconds D Programming the User Code 2 Push the Program switch 3 times the The default user code is 54321 onboard LED will be flashing and the beeper will Note This mode will only retain the last 4 user emit a long chirp to indicate the system is in codes programmed If the user code memory is Transmitter Programming mode exceeded the security system will start deleting 3 Press and hold any button on the transmitter user codes from memory in chronological order Models MKE 100 MKE 300 MKE 400
3. ote If vehicle is operating from the RV battery only the parking lights will not flash Press and Hold the 1 2 Key for 3 Seconds Locks or Unlocks the Cargo Door Operation is Sequential Upon Vehicle s Door Unlock Press and Hold the 3 4 Key for 3 Seconds Turns On the Porch Light or Turns Off the Porch Light Operation is Sequential Key in the User Code then Press and Hold the 5 6 Key for 5 Seconds Activates the Channel 3 Output LTI Key in the User Code then Press and Hold the 7 8 Key for 5 Seconds A Q tivates the Channel 4 Output Key in the User Code then Press and Hold the 9 0 Key for 5 Seconds A Q tivates the Channel 5 Output Note Turn the ignition switch to the ON position or LOCK the vehicle s doors to turn off the dome light Copyright 2005 Magnadyne Corporation MAGNADYNE MKE X UM Rev A 4 8 05
4. utton Transmitter Operation Transmitter Button System Function Remark 8 Locks the Vehicle s Doors and Cargo Door Parking Lights Flash Once d Unlocks the Vehicle s Doors 1 Parking Lights Flash Twice 2 Dome Light Turns On for 30 Seconds 3 Porch Light Turns On for 30 Seconds Note If vehicle is operating from the RV battery only the parking lights will not flash Cargo Lock Locks the Cargo Door Cargo Un Lock Unlocks the Cargo Door 8 8 Turns On the Porch Light for 30 Seconds or Turns the Porch Light Off Upon Vehicle s Door Unlock B 3 Button Transmitter Operation Transmitter Button System Function Remark 8 Locks the Vehicle s Doors and Cargo Door Parking Lights Flash Once d Unlocks the Vehicle s Doors 1 Parking Lights Flash Twice 2 Dome Light Turns On for 30 Seconds 3 Porch Light Turns On for 30 Seconds Note If vehicle is operating from the RV battery only the parking lights will not flash 7 aid AS Turns On the Porch Light for 30 Seconds or Turns the Porch Light Off Upon Vehicle s Door Unlock C Keypad Operation Keypad System Function Remark Press the LOCK Key Locks the Vehicle s Doors and Cargo Door s Parking Lights Flash Once Key in the User Code Unlocks the Vehicle s Doors 1 Parking Lights Flash Twice 2 Dome Light Turns On for 30 Seconds 3 Porch Light Turns On for 30 Seconds N
Download Pdf Manuals
Related Search