Life Fitness Seated Row User's Manual
Contents
1. 7502 7998995 7893101 3237401 3237403 8047101 10 12 13 w y BRA P P 34 37 m Q Seated Row Assembly Instructions Assemble the PULLEY 1 and two PULLEY GUARDS 2 to the TOWER SUPPORT 3 using one M10 X 45mm BOLTS 4 and one 3 8 SAE WASHER 5 as shown Tighten the BOLT securely LOOSELY assemble the BOTTOM BRACE 6 and CENTER FRAME 7 to the TOWER 8 using four M10 X 130mm BOLTS 9 eight 3 8 SAE WASHERS 5 and four M10 NYLOCK NUTS 10 as shown LOOSELY assemble the SEAT FRAME 11 to the BOTTOM BRACE 6 and CENTER FRAME 7 using four M10 X 90mm BOLTS 12 eight 3 8 SAE WASHERS 5 and four M10 NYLOCK NUTS 10 as shown LOOSELY assemble the TOWER SUPPORT 3 to the CENTER FRAME 7 and TOWER 8 using two M10 X 90mm BOLTS 12 four 3 8 SAE WASHERS 5 and two M10 NYLOCK NUTS 10 at the CENTER FRAME and two M10 X 70mm BOLTS 13 four 3 8 SAE WASHERS 5 and two M10 NYLOCK NUTS 10 at the TOWER as shown Tighten all BOLTS and NUTS securely Install the RIGHT HANDLE 14 over the right end of the HANDLE SHAFT of the WORKARM 15 as shown and secure it using one M10 x 45mm BOLT 4 Repeat for the LEFT HANDLE 16 Slide the LONG SPACER 17 PIVOT SHAFT 18 two BEARINGS 19 and SHORT SPACERS 20 into the BEARING HOUSING A of the WORKARM 15 Insert the WORKARM between the mounting plates of the CENTER FRAME 7 and secure it with two2. M10 X 25mm BOLTS 21 and two 3 8 SAE WASHERS 5 8 9 10 Assemble the OUTPUT 22 OUTPUT PLATE 23 and OUTPUT RING 24 using three M10 X 45mm BOLTS 4 and three 3 8 SAE WASHERS 5 as shown Tighten the BOLTS securely Assemble the REAR SHROUD 25 and FRONT SHROUD 26 to the TOWER 8 using four M10 X 20mm BOLTS 27 four 3 8 SAE WASH ERS 5 as shown Be sure all tabs along the sides and top of the SHROUDS are fully engaged in the slots located inside the TOWER Tighten the BOLTS securely Do not overtighten the BOLTS Secure the OUTPUT CAM ASSEMBLY B to the TOWER HUB C using one M10 X 25mm BOLTS 21 one 3 8 SAE WASHERS 5 and one PLATE 28 as shown Tighten the BOLT securely IMPORTANT Be sure the OUTPUT CAM ASSEMBLY is oriented as shown before securing it to the TOWER HUB Seated Row Assembly Instructions 11 Attach the SEAT PAD 29 to the SEAT FRAME 11 using two M10 X 35mm BOLTS 30 and two 3 8 SAE WASHERS 5 as shown Tighten the BOLT securely 12 13 14 15 16 17 NOTE Some components have been removed from the illustration for clarity Assemble one M10 HEX JAM NUT 31 onto one end of the CABLE 32 approximately 1 2 Assemble the ROD END BEARING 33 to the same end of the CABLE until it meets the M10 HEX JAM NUT Tighten the M10 HEX JAM NUT securely Loosely assemble the ROD END BEARING 33 of the CABLE 32 to the WORKARM 15 using one
3. M10 X 40mm BOLT 34 SPACER 35 3 8 SAE WASHER 5 and M10 NYLOCK NUT 10 Route the CABLE 32 around the pulley of the TOWER SUPPORT 3 and around the OUTPUT CAM ASSEMBLY B Insert the remaining end of the CABLE through the inner hole of the OUTPUT CAM ASSEMBLY Insert the CABLE RETAINING PLATE 36 over the end of the CABLE Install two M8 HEX JAM NUTS 37 to the end of the CABLE Tighten the M8 HEX JAM NUTS until the WORKARM 15 begins to move and all push pins still move in and out freely Be sure the M8 HEX JAM NUTS are tight against each other Attach the OUTPUT CAM COVER PLATE 38 to the OUTPUT CAM ASSEMBLY B using three M10 X 45mm BOLTS 4 and three 3 8 SAE WASHERS 5 Place the unit in the intended place for use and check stability If the unit is not stable the FEET D can be adjusted by inserting or removing sup plied SHIMS 39 To add or remove SHIMS loosen the LEVELING FOOT BOLT E and NUT 10 until the desired SHIM S can be inserted or removed Lightly tighten the BOLT and NUT Do not over tighten the BOLT and NUT Install HOLE PLUGS in all open bolt holes 2006 Life Fitness a division of Brunswick Corporation All rights reserved Life Fitness is a registered trademark of Brunswick Corporation TCRW 6 09 06 8060801 RevA 2
4. Seated Row Assembly Instructions Seated Row Assembly Instructions Item Qty Description 1 1 Pulley 2 2 Pulley Guard 3 1 Tower Support 4 9 M10 x 45mm Bolt 5 41 3 8 Hat Washer 6 1 Bottom Brace 7 1 Center Frame 8 1 Tower 9 4 M10 x 130mm Bolt 10 13 M10 Nylock Nut 11 1 oeat Frame 12 6 M10 x 90mm Bolt 13 2 M10 x 70mm Bolt 14 1 Right Handle 15 1 Workarm 16 1 Left Handle 17 1 Long Spacer 18 1 Pivot Shaft 19 2 Bearing 20 2 short Spacer 21 3 M10 x 25mm Bolt Tools Required 17mm Wrench Metric Allen Wrench Set Ratchet with 17mm Socket Rubber Mallet Ratchet Extension Part Number 323 801 79794XX 80385XX 3251 706 3102514 80004 80187XX 79854XX 3251720 3242002 80188XX 3251715 3251711 80191 80189XX 80190XX 7330008 7316506 3235601 7330001 3251702 Item 22 23 24 25 26 2 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Qty O wo A NO NO p Description Output Cam Output Plate Output Ring Rear Shroud Front Shroud M10 x 20mm Bolt Plate Seat Pad M10 x 35mm Bolt M10 Hex Jam Nut Cable Rod End Bearing M10 x 40mm Bolt Cable Retaining Plate M8 Hex Jam Nut Output Cam Cover Plate Leveling Shim 7 16 Hole Plug 1 Hole Plug Multi language Label Part Number 7998501 7998495 7998895 8024807 8024707 3251701 7322301 74689XX 3251704 3236901 7999601 3237901 3251705 7489402 8001801 324
Download Pdf Manuals
Related Search