Lenovo IDEACENTRE B3 User's Manual
Contents
1. O i 50000 CZ 6 Align then insert the new memory module into the socket and push down on the top edge of the memory module Make sure the latches lock the memory module in place 7 Align then slide the computer cover back into position 12 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 12 E 2011 1 19 18 02 32 OO O CR Replacing the optical drive AA Attention Turn off the computer and wait 3 to 5 minutes to let the computer cool down before replacing the optical drive To remove the optical drive O Note It may be helpful to place the computer face down on a soft flat surface for this procedure Lenovo recommends that you use a blanket towel or other soft cloth to protect the screen from scratching or other damage 1 Remove any media disks CDs or memory cards from the drives shut down the operating system and turn off the computer and all attached devices 2 Unplug all power cords from electrical outlets Disconnect all cables attached to the computer This includes power cords input output I O cables and any other cables that are connected to the computer Refer to Left and right view and Rear view for help with locating the various connectors P 4 Slide the computer cover piece as shown to re2. OO O CRER 4 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 4 2011 1 19 18 02 31 OO O CR Chapter Locations This chapter provides illustrations to help locate the various connectors controls and components of the computer Locating components and connectors The following illustrations will help you to locate the various components and connectors in your computer Font view The following illustrations show the location of connectors on the front of the A computer LD a_n ES E To 7 EE Rss La A a e i o vo ie WB 0 Ww I I i H H g E H ID Built in microphone Camera El TV indicator Hard Disk Drive Indicator Hardware Replacement Guide 5 31048859 IC B3 HRG V2 0 EN R indd 5 E 2011 1 19 18 02 31 OO O CR Bluetooth status indicator E WIFI status indicator Menu button E Direction button El Direction button LCD On Off Power button Left and right view The following illustrations show the location of connectors on the left and right side of the computer A Attention Be sure not to block any air vents on the computer Blocked air vents may cause thermal problems El Optical drive TV buttons Selected models only Card reader E USB port Headphone port E Microphone port USB port 6 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 6 E 20
3. Machine type 10069 7760 Lenovo IdeaCentre B3 Series Hardware Replacement Guide Version 2 0 2011 01 MMI ce 31048859 ideacentre lenovo OO O CR Hardware Replacement Guide O Copyright Lenovo 2011 All rights reserved LENOVO products data computer software and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C F R 2 101 with limited and restricted rights to use reproduction and disclosure LIMITED AND RESTRICTED RIGHTS NOTICE If products data computer software or services are delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 O 2011 Lenovo 31048859 IC B3 HRG V2 0 EN R indd 1 E 2011 1 19 18 02 31 OO O CRER 31048859 IC B3 HRG V2 0 EN R indd 2 2011 1 19 18 02 31 OO lt gt CR Contents ON 1 Chapter 1 Locations ii 5 Locating components and CONNECHOrS 5 Chapter 2 Replacing hardware iii 9 Gerieral INTOMMATON isola i iaia 9 Mounting the computer onto a Wall 10 Replacing a memory module eita 11 Replacing the optical drive 13 Replacing the Nard disk drive s s sair cada ie 16 Replacing
4. Replacing a memory module AN Attention Turn off the computer and wait 3 to 5 minutes to let the computer cool down before removing the computer cover Note It may be helpful to place the computer face down on a soft flat surface for this procedure Lenovo recommends that you use a blanket towel or other soft cloth to protect the touch screen from scratching or other damage 1 Remove any media disks CDs or memory cards from the drives shut down the operating system and turn off the computer and all attached devices Unplug all power cords from electrical outlets Disconnect all cables attached to the computer This includes power cords input output I O cables and any other cables that are connected to the computer Refer to Left and right view and Rear view for help with locating the various connectors 4 Slide the computer cover piece as shown to remove it from the computer Hardware Replacement Guide 11 31048859 IC B3 HRG V2 0 EN R indd 11 E 2011 1 19 18 02 32 OO O CR 5 Push out the latches on both sides of the memory socket to release the memory module and gently pull the memory module upward to remove it from its socket All of the memory modules can be removed by using the same procedure
5. in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual HMM for the computer To obtain copies of the Safety and Warranty Guide or HMM go to the Support Web site at http consumersupport lenovo com To replace the keyboard 1 Remove any media disks CDs or memory cards from the drives shut down the operating system and turn off the computer and all attached devices 2 Unplug all power cords from electrical outlets 3 Locate the connector for the keyboard Refer to Left and right view and Rear view Note Your keyboard may be connected to the standard keyboard connector at the rear of the computer or to a USB connector EH at either side or at the rear of the computer oc 3 4 Disconnect the defective keyboard cable from the computer and connect the new keyboard cable to the same connector 18 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 18 E 2011 1 19 18 02 32 OO O CR Replacing the mouse AA Attention Do not remove the computer cover or attempt any repairs before reading the Important safety information in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual HMM for the computer To obtain copies of the Safety and Warranty Guide or HMM go to the Support Web site at http consumersupport lenovo com To replace the mo
6. 11 1 19 18 02 31 OO O CR TV buttons Selected models only HO AVAVANAVANANE o E 6 Channel Up Channel Down Volume Up Volume Down E TV mode menu button E Signal source choice button TV power On Off Hardware Replacement Guide 7 31048859 IC B3 HRG V2 0 EN R indd 7 E 2011 1 19 18 02 31 OO O CR Rear view The following illustration shows the location of connectors on the rear of the computer A N s7 o o lenovo gt B a EE E C a RA O LO DE i S I ARN T SE e OS S 1000 0 Lica t ni hds e a ey ee ee ee ey ee eee EE Ethernet port TV tuner port Selected models only USB ports 5 Bluetooth reset button Only some models are functional AV IN ports I PS 2 keyboard port Power connector 8 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 8 E 2011 1 19 18 02 31 en MD Chapter Replacing hardware AA Attention Do not remove the computer cover or attempt any repairs before reading the Important safety information in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual HMM for the computer To obtain copies of the Safe
7. a part do not open the static protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part When you handle parts and other computer components take these precautions to avoid static electricity damage 2 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 2 E 2011 1 19 18 02 31 OO O CR e Limit your movement Movement can cause static electricity to build up around you e Always handle parts and other computer components carefully Handle adapters memory modules system boards and microprocessors by the edges Never touch any exposed circuitry e Prevent others from touching the parts and other computer components e Before you replace a new part touch the static protective package containing the part to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body e When possible remove the new part from the static protective packaging and install it directly in the computer without setting the part down When this is not possible place the static protective package that the part came in ona smooth level surface and place the part on it e Do not place the part on the computer cover or other metal surface Hardware Replacement Guide 3 31048859 IC B3 HRG V2 0 EN R indd 3 E 2011 1 19 18 02 31
8. e reading the Important safety information in the Safety and Warranty Guide that was included with your computer If you no longer have this copy of the Safety and Warranty Guide you can obtain one online from the Support Web site at http consumersupport lenovo com Hardware Replacement Guide 1 31048859 IC B3 HRG V2 0 EN R indd 1 E 2011 1 19 18 02 31 en MD Additional information resources If you have Internet access the most up to date information for your computer is available from the World Wide Web You can find the following information e CRU removal and installation information e Publications e Troubleshooting information e Parts information e Links to other useful sources of information To access this information go to http consumersupport lenovo com Tools required To disassemble the computer you need the following tools e Wrist grounding strap and conductive mat for preventing electrostatic discharge e Flat screwdriver DE e Philips screwdriver e Hex screwdriver e Plastic flat screwdriver e Plastic tweezers Note The screws for the different components vary in size During the disassembly procedure group the screws with their corresponding components to avoid a mismatch when replacing the components Handling static sensitive devices Static electricity although harmless to you can seriously damage computer components When you are replacing
9. l down before replacing the hard disk drive To replace the hard disk drive Note It may be helpful to place the computer face down on a soft flat surface for this procedure Lenovo recommends that you use a blanket towel or other soft cloth to protect the screen from scratching or other damage 1 Slide the computer cover piece as shown to remove it from the computer 2 Remove the 2 screws that secure the hard disk drive bay to the chassis 16 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 16 E 2011 1 19 18 02 32 OO O CR 3 Spring up the handle on the hard disk drive bay then slide and lift the hard disk drive bay out of the chassis as shown 4 Remove the 4 screws that secure the hard disk drive to the disk bay ER and slide the defective hard disk drive out of the bay 5 Install the new hard disk drive as follows 1 Slide the new hard disk drive into the drive bay 2 Screw the 4 screws back onto the drive bay 6 Slide the hard disk drive bay back into position 7 Secure the hard disk drive bay to the chassis with the remaining screw 8 Install the computer cover back into position Hardware Replacement Guide 17 31048859 IC B3 HRG V2 0 EN R indd 17 E 2011 1 19 18 02 32 en MD Replacing the keyboard A Attention Do not remove the computer cover or attempt any repairs before reading the Important safety information
10. move it from the computer P 5 Loosen the screw that secures the optical drive to the chassis Hardware Replacement Guide 13 31048859 IC B3 HRG V2 0 EN R indd 13 E 2011 1 19 18 02 32 en MD 6 Push the optical drive so that it slides out of the drive bay 7 Push a smalliron stick paper clip into the small hole on the optical drive cover so that the disk springs out as shown 8 Remove the 2 screws that secure the optical drive to the metal bracket E 9 Use a small flat head screwdriver to press and push out the pins that secure the cover to the disk 14 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 14 E 2011 1 19 18 02 32 OO O CR 10 Separate the cover from the defective optical drive 11 Install the new optical drive as follows 1 Align the new optical drive with the cover and then push the cover back into position 2 Screw the metal bracket back onto the new optical drive 3 Slide the new optical drive into the drive bay 12 Screw the new optical drive back onto the chassis 13 Slide the computer cover back into position Hardware Replacement Guide 15 31048859 IC B3 HRG V2 0 EN R indd 15 E 2011 1 19 18 02 32 O RT TT TOO Replacing the hard disk drive A Attention Turn off the computer and wait 3 to 5 minutes to let the computer coo
11. nies mentioned in the manuals included with your computer or this document do not necessarily indicate that related software or hardware is included The actual configuration of the product depends on the packing list description 22 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 22 E 2011 1 19 18 02 32
12. of the manuals included with your computer may be reproduced or transcribed by any means or translated into any language without prior written permission of Lenovo The software interface and function and hardware configuration described in the manuals included with your computer might not match exactly the actual configuration of the computer that you purchase You are welcome to contact us about the manuals included with your computer For the latest information or any questions or comments contact or visit the Lenovo Web site Service Web site http consumersupport lenovo com Hardware Replacement Guide 21 31048859 IC B3 HRG V2 0 EN R indd 21 E 2011 1 19 18 02 32 OO O CR Trademarks Lenovo and the Lenovo logo IdeaCentre and IdeaCentre logo are trademarks of Lenovo in the United States other countries or both Microsoft Windows and Windows Vista are trademarks of the Microsoft group of companies Intel Inside is a trademark of Intel Corporation in the U S and or other countries AMD the AMD Arrow logo ATI AMD Athlon AMD LIVE AMD Opteron AMD Phenom AMD Sempron Catalyst Cool n Quiet CrossFire PowerPlay Radeon and The Ultimate Visual Experience are trademarks of Advanced Micro Devices Inc Other company product or service names referred to herein or in other Lenovo publications may be trademarks or service marks of others All rights reserved Names or marks of certain compa
13. rd to the same connector 20 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 20 E 2011 1 19 18 02 32 RT gt CR Chapter Appendix Declaration Thank you for using Lenovo products Carefully read all documents shipped with your computer before you install and use the product for the first time Lenovo is not responsible for any loss except when caused by installation and operations performed by Lenovo professional service personnel You are responsible if you fail to operate the product according to instructions and requirements in the manuals included with your computer or operate the product inappropriately This manual could include technical inaccuracies or typographical errors Changes are made periodically to the information herein these changes will be incorporated P in new editions of the publication To provide better service Lenovo reserves the right to improve and or modify the products and software programs described in the manuals included with your computer and the content of the manual at any time without additional notice The manuals included with your computer are provided to help you use Lenovo s products appropriately For the configuration of the product refer to the related contract if any or product packing list or consult the distributor for the product sales The content of the manuals included with your computer is protected by copyright laws and rules None
14. the keyboard 18 DE AREplacingitNeMOUSE cric iaia 19 Replacing the power cord i 20 Chapter 3 Appendix ii 21 31048859 IC B3 HRG V2 0 EN R indd 3 E 2011 1 19 18 02 31 OO O CRER 31048859 IC B3 HRG V2 0 EN R indd 4 2011 1 19 18 02 31 en BD Overview This guide is intended to be used by customers who are replacing Customer Replaceable Units CRUs as well as trained service personnel who are replacing Field Replaceable Units FRUs In this guide CRUs and FRUs will often be referred to as parts Note Trained service personnel should refer to the Hardware Maintenance Manual HMM for parts ordering information This guide does not include procedures for all parts It is expected that cables switches and certain mechanical parts can be replaced by trained service personnel without the need for step by step procedures Note Use only parts provided by Lenovo The description of the TV Tuner card in this manual applies only to those computer models that have the TV Tuner card installed It does not apply to those computer models that do not have the TV Tuner card installed This guide contains procedures for replacing the following parts e Memory modules e Hard disk drive e Optical drive e Keyboard Mouse wired e Powercord Safety information for replacing CRUs Do not open your computer or attempt any repairs befor
15. ty and Warranty Guide or HMM go to the Support Web site at http consumersupport lenovo com Note Use only parts provided by Lenovo Ea General information Pre disassembly instructions Before proceeding with the disassembly procedure make sure that you do the following 1 Tum off the power to the system and all peripherals 2 Unplug all power and signal cables from the computer 3 Place the system on a flat stable surface Hardware Replacement Guide 9 31048859 IC B3 HRG V2 0 EN R indd 9 E 2011 1 19 18 02 31 OO O CR Mounting the computer onto a wall The computer can be mounted onto a wall Before doing this you will first need to install a UL listed VESA wall mount to be purchased separately onto the back of the computer To install a VESA wall mount Note It may be helpful to place the computer face down on a soft flat surface for this procedure Lenovo recommends that you use a blanket towel or other soft cloth to protect the touch screen from scratching or other damage 1 Remove the 2 screws that secure the stand to the computer and then slide the stand out 2 Align the VESA wall mount with the mounting holes on the computer and then secure it to the computer with the 4 screws VESA wall mount spec VESA100 100mm x 100mm M4 bolts 10 Hardware Replacement Guide 31048859 IC B3 HRG V2 0 EN R indd 10 E 2011 1 19 18 02 32 OO O CR
16. use 1 Remove any media disks CDs or memory cards from the drives shut down the operating system and turn off the computer and all attached devices Unplug all power cords from electrical outlets Locate the connector for the mouse Refer to Left and right view and Rear view Note Your mouse will be connected to the USB connector at either side or at the rear of the computer e E 5 4 Disconnect the defective mouse cable from the computer and connect the new mouse cable to the same connector Hardware Replacement Guide 19 31048859 IC B3 HRG V2 0 EN R indd 19 E 2011 1 19 18 02 32 OO O CR Replacing the power cord A Attention Do not remove the computer cover or attempt any repairs before reading the Important safety information in the Safety and Warranty Guide that was included with your computer or in the Hardware Maintenance Manual HMM for the computer To obtain copies of the Safety and Warranty Guide or HMM go to the Support Web site at http consumersupport lenovo com To replace the power cord 1 Remove any media disks CDs or memory cards from the drives shut down the operating system and turn off the computer and all attached devices 2 Locate the connector for the power cord Refer to Rear view 3 Disconnect the defective power cord from the computer and connect the new power co
Download Pdf Manuals
Related Search