KitchenAid KHMS 106 User's Manual
Contents
1. 2 Withdraw hood fan unit Fig 6 pg 11 3 Change lead wire holding position from left side wire retainer to right side wire retainer Fig 11 wire retainer 4 Rotate hood fan unit so exhaust opening faces in to Figure 11 wards the upper side of the oven Replace hood fan unit into oven unit by pressing it as shown Fig 12 Be careful that back plate and hood fan unit do not pinch lead wire 5 Replace rear stay First attach rear stay to unit with 2 screws Fig 9 pg 12 Safety Screw is located on the rear stay to prevent im proper installation Do not remove this screw If you cannot attach rear stay to the back plate precisely the hood fan unit is improperly placed and the safety screw will not line up Check steps 3 amp 4 again 6 Secure using remaining 7 screws Fig 10 pg 12 Figure 12 NOTE Backdraft Damper is not required for recirculating exhaust It is recommended that the Backdraft Damper be saved should outside venting be decided upon at a later time 13 PREPARATION OF WALL AND TOP CABINET MOUNTING TEMPLATES CAUTION THIS PRODUCT CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO MOUNTING INSTRUCTIONS ON BOTH TEMPLATES Read and follow mounting information on both Top Cabinet and Wall Templates Templates are included in the printed matters packed with this oven WALL AND TOP CABINET 1 The mounting area on top cabinet and wall must be capable of supporting a minimum o2. d Figure 19 11 Make a bundle of power supply cord then fix it to cabinet using cord hook A short power supply cord is provided to reduce the risks resulting from contacting the cooking sur face or from becoming tangled Extension cords are available and may be used if care is exercised in their use If an extension cord is used 1 the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance 2 the extension cord must be a grounding type 3 wire cord and 3 the extension cord should be arranged so that it will not drape over the countertop or cooking surface where it can be pulled on by children or tripped over accidentally 18 CHECK LIST FOR INSTALLATION 1 2 Make sure unit has been installed according to instructions Remove all packing material from the oven Plug in power cord Read Use and Care Manual Keep installation instructions for the local electrical inspector s use ACCESSORIES 1 CHARCOAL FILTER KIT 307931 Filter is used for recirculating exhaust 19 Form 85032 Printed in U S A KitchenAid Inc St Joseph MI 49085
3. AUST A OUTSIDE VENTILATION Vertical Exhaust The unit is shipped assembled for Vertical Exhaust Attach the Backdraft Damper on the outer case cabinet with 2 tapping screws provided Fig 4 Proceed to Preparation of Wall and Top Cabinet page 14 Figure 4 10 B OUTSIDE VENTILATION Horizontal Exhaust 1 Remove and save 9 screws Remove rear stay Fig 5 Figure 5 2 Withdraw hood fan unit carefully Fig 6 Figure 6 3 Rotate hood fan unit 4 turn Fig 7 Figure 7 4 Replace hood fan unit into oven unit with left corner side inserted into opening first right corner next Be careful not to pinch the lead wire between the back plate and hood fan unit Fig 8 Figure 8 5 Replace the rear stay First attach rear stay to unit with 2 screws Fig 9 Make sure the fan blades are visible through the openings in the rear stay before proceeding Safety Screw is located on the rear stay to prevent improper installation Do not remove this screw If you cannot attach rear stay to the back plate precisely the hood fan unit is improperly placed and the safety screw will not line up Safety Screw Figure 9 6 Secure using remaining 7 screws Fig 10 The hood fan unit is now rotated for horizontal exhaust Figure 10 7 See page 15 for Backdraft Damper installation 12 C RECIRCULATING Non Vented Ductless 1 Remove and save 9 screws Remove rear stay Fig 5 pg 11
4. INSTALLATION INSTRUCTIONS KitchenAid 30 BUILT IN MICROWAVE HOOD MODEL KHMS 105 MICROWAVE CONVECTION HOOD MODEL KHMC 106 Read And Save These Installation Instructions INTRODUCTION Please read all instructions thoroughly before installing Microwave Hood System TWO PEOPLE are required to insiall this product If a new electrical outlet is required it should be connected by a qualified electrician before the Microwave Hood 5 is installed MOUNTING SPACE Microwave Hood System requires mounting space on a wall as shown below 30 OR MORE FROM COOKING SURFACE BACKSPLASH N lt 66 MORE FROM FLOOR For removal of the Microwave Hood System bottom cover for cleaning or servicing a 2 inch space is necessary between the top of the range backsplash and the bottom of the Microwave Hood System WALL CONSTRUCTION Microwave Hood System should be mounted against and supported by a flat vertical wall If wall is not flat use spacers to fill gaps Mounting plate must be flat for proper installation Wall construction should be a minimum of 2 x 4 wood studding and 3 8 or more thick dry wall or plaster lath The unit must be attached to a minimum of one 2 x 4 wall stud For proper installation the wall must be capable of supporting a minimum of 140 pounds the 90 pound weight of product and load weight allowance of 50 pounds To find studs use one of the
5. f 140 pounds If wall is not flat use spacers to fill gaps Mounting plate must be flat for proper installation 2 Wall space for installation should be the same as the wall template Make sure top of wall template is at least 66 from the floor and 30 from the cooking surface For easier access to the hood lamp the bottom of Microwave Hood System should be at least 2 above backsplash of range GO TO WALL AND TOP CABINET TEMPLATES 14 MOUNTING PLATE INSTALLATION 3 1 Separate toggle bolts from toggle nuts mmm 2 Insert one toggle bolt into each hole on the mounting plate these holes correspond to holes A B C and D of MOUNTING I the Wall Template and put toggle nut onto the toggle PLATE Figure 13 bolt Fig 13 If hole is located in a stud do not use toggle bolt 3 If using horizontal exhaust follow these two 2 steps If method other than horizontal continue to step 4 1 Attach Backdraft Damper assy to the back of mount ing plate with 2 tapping screws provided for OUTSIDE VENTILATION Horizontal Exhaust Fig 14 2 Connect the Backdraft Damper assy to the horizon tal duct Insure that Backdraft Damper plate is allowed to move freely See Fig 14a BACK OF MOUNTING PLATE 4 Insert nut and bolt through the hole in the wall with Figure 14 toggle nut closed Fig 15 NOTE Before you do this be sure you leave space at least the thickness of the wall between the mount
6. following methods Stud Finder a magnetic device which locates nails B Use a hammer to tap lightly across the mounting surface to find a solid sound This will indicate a stud installation 2 x 4 WOOD STUDS r nP 3 8 DRY WALL or PLASTER LATH The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then placing a mark half way between the edges The center of any adjacent studs will be 16 or 24 from this mark ELECTRICAL SERVICE Visual check after unpacking Remove all packing material from the oven cavity Check the oven for any damage such as misaligned door damaged gaskets around door or dents inside the oven cavity or on the door If here is any damage please do not operate the oven until it has been checked by an Authorized KitchenAid Servicer and any repairs made if necessary GROUNDING INSTRUCTIONS This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounded WARNING Improper use of the grounding plug can result in a risk of electric shock If it is necessary to use an extension cord use only a 3 wire extension cord that has a 3 blade
7. grounding plug and a 3 slot receptacle that will accept the plug on the appliance The marked rating of the exten sion cord should be AC 115 120 Volt 15 Amp or more The extension cord should be located in the cabinet above the Microwave Hood System It should not hang over edge of cabinet or in front of cooking surface Consult a qualified electrician or serviceman if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded The power supply cord and plug must be connected to a separate AC 120 Volt 60 Hz 15 or 20 Amp branch circuit single grounded receptacle The receptacle should be located inside the cabinet directly above the Microwave Hood System mounting location 5 HOOD EXHAUST DUCT Outside ventilation requires HOOD EXHAUST DUCT Read the following carefully EXHAUST CONNECTION The hood exhaust has been designed to mate with a standard 3 14 x 10 rectangular duct If round duct is required a rectangular to round transition adaptor must be used Do not use less than a 6 diameter duct REAR EXHAUST If rear or horizontal exhaust is to be used care should be taken to align ex haust with space between studs or wall should be prepared at the time it is constructed by leav ing enough space between wall studs to accommodate exhaust MAXIMUM DUCT LENGTH For satisfactory air movement the total duct length of 3 4 x 10 rectangular
8. her material to protect the outercase from being damaged 2 Stand the unit on its side as shown in Fig 1 FRONT SIDE GREASE FILTER OPENINGS Figure 1 3 Remove and save two hexagonal Philiips head screws inside grease filter openings Fig 2 HEXAGONAL PHILLIPS HEAD SCREW Figure 2 8 LOWER HOOKS UPPER HOOKS LEVERS SLIDERS Figure 3 Pull out two levers to release sliders from hooks This action will release mounting plate from back surface of outercase Familiarize yourself with the operation of the mounting levers so you will be aware of the proper pro cedure for mounting the unit to the wall Gently pull mounting plate toward you and slide it to the right Mounting plate is attached to outercase at both upper and lower sides VENTILATION SYSTEM MICROWAVE HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THE FOLLOWING THREE 3 TYPES OF VENTILATION SYSTEMS Select the type required for your installation a OUTSIDE VENTILATION Vertical Exhaust b OUTSIDE VENTILATION Horizontal Exhaust c RECIRCULATING Non Vented ductless installation requires use of charcoal filters packed with product your Microwave Hood System is set for Vertical Exhaust follow the procedure listed below to attach the Backdraft Damper if you desire Vertical Exhaust If you prefer Horizontal Exhaust proceed to page 11 or for recirculating exhaust proceed to page 13 ADAPTING HOOD FAN UNIT FOR ALTERNATE EXH
9. ing plate and the end of toggle nut in closed posi tion If you do not leave this space toggle nut will not open on the other side of wall 5 Turn toggle bolt clockwise to tighten Fig 15a 6 Secure mounting plate to a minimum of one stud with a wood screw provided SectionA A SectionA A Closed Open Figure 14a Space More Than Wall Thickness Figure 15 Figure 15a 15 PRODUCT INSTALLATION 1 Place styrofoam packing blocks 2 pieces on top surface of range cooktop Figure 16 2 Place microwave hood system on top of styrofoam blocks as shown in Fig 16 3 Thread power supply cord through the hole at the bottom of top cabinet 4 Using two 2 people hang the unit on the hooks at the bottom of the mounting plate Lift unit upward and hold ssed to the wall anit slightly out from the mounting plate 6 Pull levers down Press unit to mounting plate Push levers back up Figure 17 16 7 Check to be sure the unit is secure to the mounting plate at both upper and lower hooks when you remove your support 8 Screw hexagonal Phillips head screws to levers inside grease filter opening Fig 18 Figure 18 9 Check that both levers a are securely fixed If not tighten screws Fig 18 10 Replace grease filters 17 10 Use adjusting screws c and flat washers d for gaps between top cabinet and unit Fig 19 c
10. or 6 diameter round duct should not exceed 140 feet ELBOWS TRANSITIONS WALL and ROOF CAPS etc present additional resistance to air flow and are equivalent to a section of straight duct which is longer than their actual physical size When calculating the total duct length add the equivalent lengths of all transitions and adaptors plus the lengths of all straight duct sections The diagram below shows the approximate feet of equivalent length of some typical ducts EXHAUST DUCT 90 ELBOW 10 FT 45 ELBOW 5 FT 5 FT TRANSITION ADAPTOR 10 WIDE ELBOW 10 FT 90 ELBOW 45 ELBOW 25 FT 5 FT ROOF CAP 24 FT WALL CAP 40 FT TOOLS RECOMMENDED FOR INSTALLATION Phillips Screw Driver Pencil Electric Drill Measure 5 8 3 32 Drill Bit Tape 1 1 2 Wood Bit Saw to cut exhaust opening if needed Protective drop cloth for product and range You may use part of carton for protection INSTALLATION HARDWARE The installation hardware packed with the product should include the following NAME QUANTITY Wood Screw 5x30mm Toggle Bolts 3 16 inch Screw 5x55mm Flat Washer 30mm Dia Tapping Screw 4x12mm Power Cord Hanger Grommet Back Draft Damper r NN AW O Ox 3 DD Om PREPARATION OF PRODUCT REMOVING MOUNTING PLATE 1 Use a portion of the carton or some ot
Download Pdf Manuals
Related Search