Home

HP 3C900 User's Manual

1. 13 Select 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X in the Unlisted or Updated Network Adapter dialog box and click OK 14 Make sure that the 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X NDIS2 NDIS3 is selected in Network Drivers 15 Accept the applicable Network Protocols and then click on CLOSE 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X NDIS2 NDIS3 Microsoft NetBEUI IPX SPX Compatible Transport with NetBIOS If you do not have the required information contact your network administrator 16 At the Network Setup dialog box click on OK 17 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK The Drivers will now start to copy 18 Set the Install Driver dialog path to A wfw311 and click OK to complete file copying 19 Finish the network card installation by clicking on OK in the Network Setup message 20 To complete the installation click on Restart Computer button inthe Windows Setup dialog box Windows 95 SR2 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 3COM Etherlink 3C900 Ethernet card and drivers disk Ver 2 1 Driver Name El90X DOS Size 45KB Date 3 21 97 Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX an
2. Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e MediaType Auto Select N WAY 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 PCI adapter card into a PCI slot Connect network media to the 3COM 3C900 PCI card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM Etherlink 3C900 Ethernet card and drivers Disk 1 Ver 2 1 and execute A 3C90XCFG E XE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3com cards driver diskette and reboot the machine Power on the machine and allow it to boot to Windows NT Workstation 4 0 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 9 Log onto the machine with Administrator privileges If you do not have the required information contact your network administrator 10 Click on Start and move to Settings open the Control Panel and double click on Network 11 Click on Yes and agree to install Windows NT Networking 12 With Wired to the Network checked click on
3. 17 Specify your User Name Workgroup and Computer Name in Microsoft Windows Network Names dialog box and click on OK The Drivers will now start to copy 18 Set the Install Driver dialog path to A wfw311 and click OK to complete file copying 19 Finish the network card installation by clicking on OK in the Network Setup message 20 To complete the installation click on Restart Computer button inthe Windows Setup dialog box Windows 95 SR2 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 3COM Etherlink 3C900 Ethernet card and drivers disk Ver 2 1 Driver Name El90X DOS Size 45KB Date 3 21 97 Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e MediaType Auto Select N WAY e 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 adapter 9 card into an PCI slot Connect network Cable media to the 3COM 3C900 card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM drivers disk 1 Etherlink 3C900 Ethernet Drivers Ver 2 1 and execute A 3C90XCFG EXE Select Configure NIC and
4. Next 13 Click on the option to Select from list then on Have Disk 14 Insert the 3COM 3C900 drivers disk 1 of 2 into the floppy drive 15 Change the path to A and click OK If you have a Hewlett Packard pre loaded HDD set the path statement to C LANDRV 3C900 Disk1 16 Select 3Com Fast Etherlink XL Adapter 3C900 and click OK 17 With 3Com Fast Etherlink XL Adapter 3C900 listed in the Network Adapters window click on Next 18 Accept the default Network Protocol TCP IP and click on any additional protocols then click Next If you do not have the required Protocols information contact your network administrator 19 At the Network Services prompt accept default settings and click on N ext 20 Finish the network card installation by clicking on Next 21 Designate the path to your NT files and select Continue If you have a Hewlett Packard pre loaded HDD set the path to C 1386 22 Insert the 3COM 3C900 drivers disk 2 of 2 into the floppy drive and hit enter If you have a Hewlett Packard pre loaded HDD set the path statement to C LANDRV 3C900 DISK2 23 After the files transfer from Disk 2 of 2 you will be prompted to provide the path to your NT files DO NOT follow this direction Ignore the request an set the path to A on disk 2 of 2 instead 24 A setup message of 3Com dRMON SmartAgent will ap
5. Protocol from Select Network Component Type and click on Add 19 Pick Microsoft from Manufacturers then TCP IP and then click OK 20 Highlight the TCP IP network component and click on the Properties button 21 If you know your TCP IP settings enter them now other wise leave the IP address choice checked Obtain an IP address automatically and click OK If you do not have the required information contact your network administrator 22 Click on Close button and files will copy 23 When prompted specify the path to your Windows 95 CD ROM and click on OK If you have an HP pre loaded HDD set the path to C AMASTERS WIN95 SYSTEM CABS 24 Click on OK in the Please insert the 3Com drivers disk 2 dialog box 25 Set the path to A and click on OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 DISK 2 26 Click on Yes button to finish the Setup installation and restart your computer to the System settings Change dialog box 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 Windows NT Workstation Version 3 51 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 Requirements HP Vectra with Microsoft Windows NT Workstation 3 51 installed 3COM Etherlink 3C900 ethernet card and drivers d
6. Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3Com Software driver diskette and reboot the machine After windows loads log onto the machine with administrator privileges If you do not have the required information contact your network administrator Open the Main Program Group and double click on Control Panel Icon 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 10 Double click on the Network icon in the Control Panel program group 11 Click on YES in the Network Settings dialog box and NT Networking will be installed on your computer 12 Insert the Windows NT Workstaion CD 13 In the Windows NT Setup window set the path to your NT files and click on the Continue button If you have an HP preloaded HDD set path to C 1386 14 Click on the Do Not Detect button from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card Detection dialog box 15 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 16 Set the path to A V in the Insert Disk dialog box and then insert the 3COM 3C900 drivers disk 1 17 Click OK at the Install Driver di
7. installation remove the floppy disk and click on Restart Computer button in the Windows NT Workstation Networking Setup dialog box 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 Windows NT Workstation 4 0 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 Requirements HP Vectra with Windows NT Workstation 4 0 Service Pack 3 3COM Etherlink 3C900 Ethernet card and drivers disk ver 2 1 Driver Name 3C90X INF Size 71KB Date 11 25 96 Microsoft Windows NT Workstation 4 0 and Service Pack Media If you have a Hewlett Packard pre loaded HDD the media is located at C 1386 Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e MediaType Auto Select N WAY 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 PCI adapter card into a PCI slot Connect network media to the 3COM 3C900 PCI card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM Etherlink 3C900 Ethernet card and drivers Disk 1 Ver 2 1 and execute A 3C90XCFG E XE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Con
8. on YES in the Network Settings dialog box and NT Networking will be installed on your computer 12 Insert the Windows NT Workstaion CD 13 In the Windows NT Setup window set the path to your NT files and click on the Continue button If you have an HP preloaded HDD set path to C 1386 14 Click on the Do Not Detect button from the Network Adapter Card Detection dialog box and click on Continue in the second Network Adapter Card Detection dialog box 15 From the Drop Down List scroll down and select lt Other gt Requires disk from manufacturer then click on Continue 16 Set the path to A V in the Insert Disk dialog box and then insert the 3COM 3C900 drivers disk 1 17 Click OK at the Install Driver dialog box If you have an HP preloaded HDD set path to C LANDRV 3C900 DISK 1 18 Select 3Com Fast Etherlink XL Adapter 3C900 in the Select OEM Option dialog box and click OK 19 When prompted insert 3C900 Ethernet drivers disk 2 of 2 ver 2 1 and click on OK If you have an HP preloaded HDD set path to C LANDRV 3C900 DISK 2 20 Click on the OK button in the 3Com DRMON SmartAgent PC Software dialog box 21 Click on the Close button in the 3Com NIC Diagnostics v1 0 dialog box 22 Choose the default Protocol TCP IP and any additional Network Protocols by clicking the check box
9. 0 Ethernet card and drivers disk ver 2 1 DOS ODI File Name 3C90X COM Size 59KB Date 12 18 96 DOS and MS Windows for Workgroups 3 11 media Novell Netware server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Netware client for DOS and MS Windows Device Configuration e Network Driver Optimization Normal e Full Duplex Disabled e Boot PROM Disabled e MediaType 10BASE T e 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink IIH 3C900 adapter card into a PCI slot Power on the machine and allow it to boot to a DOS prompt Insert the 3COM drivers diskette ver 2 1 downloaded from 3COM s website and execute 3C90XCFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3com cards driver diskette and insert Netware client for DOS and MS Windows disk 1 1 Connecting to a Netware 3 12 Server Windows for Workgroups 7 Execute INSTALL EXE and set lines 1 5 as listed below CANWCLIENT e YES e YES CAWINDOWS e NO e 3COM Etherlink XL F ast Etherlink XL Family 8 Highlight option 6 to continue with installation 9 When prompted insert the corresponding disks to complete file transfer and driver installation 10 When the install utility is finished press lt CRTL
10. A packar Etherlink XL PCI Network Interface Card 3C900 Installation Guide Notice The information contained in this document is subject to change without notice Hewlett Packard makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose Hewlett Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Hewlett Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett Packard This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Microsoft Windows and MS DOS are registered trademarks of Microsoft Corporation MMXTM is a trademark of Intel Corporation Pentium is aregistered trademark of Intel Corporation Hewlett Packard France Commercial Desktop Computing Division 38053 Grenoble Cedex 9 France Windows for Workgroups 1 Connecting to a Netware 3 12 Server Windows for Workgroups 1 Connecting to a Netware 3 12 Server Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C90
11. OK in order to provide Computer and Workgroup names 16 At the Network dialogue box click on the Identification folder 17 Enter your Computer Name Workgroup and Computer Description And click on Close If you do not have a Computer name Workgroup name and Computer description contact your network administrator 18 At the Insert Disk notification click on OK 19 Set the path to your Windows 95 SR2 media and click on OK If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs 20 When prompted insert the 3C900 driver s disk 2 of 2 and click on OK 21 Set the path to A and click on OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 Disk2 22 Click on YES to complete installation and restart the machine Windows for Workgroups Version 3 11 3 Connecting to a Windows NT Server 3 51 Windows for Workgroups Version 3 11 3 Connecting to a Windows NT Server 3 51 Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C900 Ethernet card and drivers disk ver 2 1 DOS ODI Driver Name EL90X DOS Size 46KB Date 3 21 97 NDIS Driver Name E190X 386 Size 55KB Date 12 20 96 Microsoft Windows NT Server 3 51 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimizat
12. OM Disabled e MediaType 10BASE T e 1 O Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink IIHI 3C900 adapter card into a PCI slot Power on the machine and restart Windows 95 SR2 in MS DOS Mode Insert the 3COM drivers diskette ver 2 1 downloaded from 3COM s website and execute 3C90XCFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3com cards driver diskette and restart the machine Windows 95 SR2 should automatically recognize the 3COM 3C900 ethernet card With PCI Ethernet Controller listed click on Next Click on Other Locations and insert the 3C900 driver s disk 1 of 2 2 Connecting to a Netware 4 11 Server Windows 95 SR2 10 Set the path to A and click on OK If you have a Hewlett Packard pre loaded HDD set the path statement to C LANDRV 3C900 Disk1 11 3Com Etherlink XL TPO 10Mb Ethernet Adapter should now be listed Click on Finish 12 When prompted insert the 3C900 driver s disk 2 of 2 and click on OK 13 In the Copying Files window the path should read A If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 Disk2 14 Click on OK to continue the installation 15 Click on
13. alog box If you have an HP preloaded HDD set path to C LANDRV 3C900 DISK 1 18 Select 3Com Fast Etherlink XL Adapter 3C900 in the Select OEM Option dialog box and click OK 19 When prompted insert 3C900 Ethernet drivers disk 2 of 2 ver 2 1 and click on OK If you have an HP preloaded HDD set path to C LANDRV 3C900 DISK 2 20 Click on the OK button in the 3Com DRMON SmartAgent PC Software dialog box 21 Click on the Close button in the 3Com NIC Diagnostics v1 0 dialog box 22 Choose the default Protocol TCP IP and any additional Network Protocols by clicking the check boxes in the Windows NT Setup dialog box and click Continue If you do not have the required information contact your network administrator 23 Check the boxes to add additional TCP IP components and click on the Continue button 24 Click OK in the Network Settings dialog box 25 Set your IP address information in the TCP IP Configuration dialog box and click OK If you do not have the required TCP IP Settings contact your network administrator 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 26 At the Domain Workgroup Settings dialog box click on OK to accept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator 27 To complete the
14. d NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e MediaType Auto Select N WAY e 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 adapter 9 card into an PCI slot Connect network Cable media to the 3COM 3C900 card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM drivers disk 1 Etherlink 3C900 Ethernet Drivers Ver 2 1 and execute A 3C90XCFG EXE Select Configure NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3Com Software driver diskette and reboot the machine When Windows 95 restarts a message will appear that new hardware has been found Insert 3Com Etherlink 3C900 software disk 1 of 2 ver 2 1 10 Click Next to begin hardware wizard on the Update Device Driver Wizard dialog message 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 11 Click on Other Locations in the Update Device Driver Location dialog box and set path to A then click OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 DISK 1 12 3Com EtherLink XL TPO 10Mb Ethernet Adapter should now be listed cl
15. ed save those changes and exit Remove the 3com cards driver diskette and insert Netware client for DOS and MS Windows disk 1 2 Connecting to a Netware 4 11 Server Windows for Workgroups 7 Execute INSTALL EXE and set lines 1 5 as listed below C NWCLIENT e YES e YES C WINDOWS e NO e 3COM Etherlink XL Fast Etherlink XL Family 8 Highlight option 6 to continue with installation 9 When prompted insert the corresponding disks to complete file transfer and driver installation 10 When the install utility is finished press lt CRTL gt lt ALT gt lt DEL gt to restart the machine 11 After windows loads open the NETWORK folder and double click the NETWORK SETUP icon 12 Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the following network only and click on OK Windows 95 SR2 2 Connecting to a Netware 4 11 Server Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 installed 3COM Etherlink 3C900 Ethernet card and drivers disk ver 2 1 File Name OEMSETUP INF Size 41KB Date 3 14 97 Windows 95 SR2 media If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs Novell Netware 4 11 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Disabled e Boot PR
16. es in the Windows NT Setup dialog box and click Continue If you do not have the required information contact your network administrator 23 Check the boxes to add additional TCP IP components and click on the Continue button 24 Click OK in the Network Settings dialog box 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 25 Set your IP address information in the TCP IP Configuration dialog box and click OK If you do not have the required TCP IP Settings contact your network administrator 26 At the Domain Workgroup Settings dialog box click on OK to accept the default Workgroup as your workgroup name If you do not have the required information contact your network administrator 27 To complete the installation remove the floppy disk and click on Restart Computer button in the Windows NT Workstation Networking Setup dialog box 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 Windows NT Workstation 4 0 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 Requirements HP Vectra with Windows NT Workstation 4 0 Service Pack 3 3COM Etherlink 3C900 Ethernet card and drivers disk ver 2 1 Driver Name 3C90X INF Size 71KB Date 11 25 96 Microsoft Windows NT Workstation 4 0 and Service Pack Media If you have a Hewlett Packard pre loaded HDD the media is located at C 1386
17. figuration If changes are required save those changes and exit Remove the 3com cards driver diskette and reboot the machine Power on the machine and allow it to boot to Windows NT Workstation 4 0 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 9 Log onto the machine with Administrator privileges If you do not have the required information contact your network administrator 10 Click on Start and move to Settings open the Control Panel and double click on Network 11 Click on Yes and agree to install Windows NT Networking 12 With Wired to the Network checked click on Next 13 Click on the option to Select from list then on Have Disk 14 Insert the 3COM 3C900 drivers disk 1 of 2 into the floppy drive 15 Change the path to A and click OK If you have a Hewlett Packard pre loaded HDD set the path statement to C LANDRV 3C900 Disk1 16 Select 3Com Fast Etherlink XL Adapter 3C900 and click OK 17 With 3Com Fast Etherlink XL Adapter 3C900 listed in the Network Adapters window click on Next 18 Accept the default Network Protocol TCP IP and click on any additional protocols then click Next If you do not have the required Protocols information contact your network administrator 19 At the Network Services prompt accept default settings and click on N ext 20 Fi
18. gt lt ALT gt lt DEL gt to restart the machine 11 After windows loads open the NETWORK folder and double click the NETWORK SETUP icon 12 Select Networks and verify that Novell Netware Workstation Shell 4 0 and above is listed under Install Windows support for the following network only and click on OK Windows 95 SR2 1 Connecting to a Netware 3 12 Server Windows 95 SR2 Requirements HP Vectra with Windows 95 SR2 installed 3COM Etherlink 3C900 Ethernet card and drivers disk ver 2 1 File Name OEMSETUP INF Size 41KB Date 3 14 97 Windows 95 SR2 media If you have an HP preloaded HDD the media is located at C Masters Win95 System Cabs Novell Netware 3 12 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Disabled e Boot PROM Disabled e MediaType 10BASE T e 1 0 Base Address F CCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink IIHI 3C900 adapter card into a PCI slot Power on the machine and restart Windows 95 SR2 in MS DOS Mode Insert the 3COM drivers diskette ver 2 1 downloaded from 3COM s website and execute 3C90XCFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exi
19. ick on Finish 13 Insert Disk 2 of 2 of the 3Com drivers disks and click OK 14 In Copying Files dialog box set path to A and click OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C9OO DISK 2 15 Click OK at the Network dialog box to provide computer work group names 16 Specify your Computer Name Workgroup and Computer Description but do NOT press enter If you do not have the required information contact your network administrator 17 Click on the Configuration folder in the Network Dialog Box 18 Click on Add and then Protocol from Select Network Component Type and click on Add 19 Pick Microsoft from Manufacturers then TCP IP and then click OK 20 Highlight the TCP IP network component and click on the Properties button 21 If you know your TCP IP settings enter them now other wise leave the IP address choice checked Obtain an IP address automatically and click OK If you do not have the required information contact your network administrator 22 Click on Close button and files will copy 23 When prompted specify the path to your Windows 95 CD ROM and click on OK If you have an HP pre loaded HDD set the path to C AMASTERS WIN95 SYSTEM CABS 24 Click on OK in the Please insert the 3Com drivers disk 2 dialog b
20. ion Normal e Full Duplex Disabled e Boot PROM Disabled e MediaType 10Base T e 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 adapter card into a PCI slot Connect network cable media to the 3COM 3C900 card After booting insert the 3COM s drivers disk Etherlink 3C900 Ethernet ver 2 1 disk 1 of 2 and execute A 3C90XCFG E XE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3COM drivers diskette and reboot the machine After windows loads open the NETWORK program group and double click on Network Setup Select the Networks button in the Network Setup dialog box 3 Connecting to a Windows NT Server 3 51 Windows for Workgroups Version 3 11 9 Click on the Install Microsoft Windows Network Option and click OK 10 Click on the Drivers button from the Network Setup dialog box and click on Add Adapter 11 Click OK to accept the default choice of Unlisted or Updated Network Adapter 12 Type the path A WFW311 in the Install Driver dialog box then insert the 3COM 3C900 drivers disk 1 into the floppy drive and click OK If you have an HP preloaded HDD set path to C LANDRV 3C900 DISK 1 WF W311
21. isk ver 2 1 DriverName OMESETUP INF Size 41KB Date 3 14 97 Microsoft Windows NT Workstation 3 51 and Service Pack Media Microsoft Windows NT Server 4 0 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e MediaType Auto Select N WAY 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 adapter card into a PCI slot Connect network cable media to the 3C0M 3C900 card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM Software 3C900 Ethernet drivers disk ver 2 1 and execute A 3C90XCFG E XE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3Com Software driver diskette and reboot the machine After windows loads log onto the machine with administrator privileges If you do not have the required information contact your network administrator Open the Main Program Group and double click on Control Panel Icon 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation Version 3 51 10 Double click on the Network icon in the Control Panel program group 11 Click
22. istrator 30 After Network has been installed on this computer click on Finish 31 To complete the installation select Yes to reboot your computer 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 Windows for Workgroups Version 3 11 4 Connecting to a Windows NT Server 4 0 Windows for Workgroups Version 3 11 4 Connecting to a Windows NT Server 4 0 Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C900 Ethernet card and drivers disk ver 2 1 DOS ODI Driver Name EL90X DOS Size 46KB Date 3 21 97 NDIS Driver Name E190X 386 Size 55KB Date 12 20 96 Microsoft Windows NT Server 4 0 machine that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Disabled e Boot PROM Disabled e MediaType 10Base T 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 adapter card into a PCI slot Connect network cable media to the 3COM 3C900 card After booting insert the 3COM s drivers disk Etherlink 3C900 Ethernet ver 2 1 disk 1 of 2 and execute A 3C90XCFG E XE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3COM d
23. nish the network card installation by clicking on Next 21 Designate the path to your NT files and select Continue If you have a Hewlett Packard pre loaded HDD set the path to C 1386 22 Insert the 3COM 3C900 drivers disk 2 of 2 into the floppy drive and hit enter If you have a Hewlett Packard pre loaded HDD set the path statement to C LANDRV 3C900 DISK2 23 After the files transfer from Disk 2 of 2 you will be prompted to provide the path to your NT files DO NOT follow this direction Ignore the request an set the path to A on disk 2 of 2 instead 24 A setup message of 3Com dRMON SmartAgent will appear click on OK 25 At the 3Com NIC Diagnostics ver 1 0 message click on Close 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation 4 0 26 If you know what your TCP IP settings are click NO and enter the IP settings when prompted If You DO NOT know what your TCP IP settings will be click on YES to Obtain an IP address automatically and continue If you do not have the required information contact your network administrator 27 At the Show Bindings for window accept default entries and click N ext 28 When Windows NT is now ready to start the network click on Next 29 Specify your Computer Name Workgroup or Domain and click on Next If you do not have the required information contact your network admin
24. ox 25 Set the path to A and click on OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 DISK 2 26 Click on Yes button to finish the Setup installation and restart your computer to the System settings Change dialog box 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 3 Connecting to a Windows NT Server 3 51 Windows 95 SR2 Windows NT Workstation Version 3 51 3 Connecting to a Windows NT Server 3 51 Windows NT Workstation Version 3 51 Requirements HP Vectra with Microsoft Windows NT Workstation 3 51 installed 3COM Etherlink 3C900 ethernet card and drivers disk ver 2 1 DriverName OMESETUP INF Size 41KB Date 3 14 97 Microsoft Windows NT Workstation 3 51 and Service Pack Media Microsoft Windows NT Server 3 51 machine that supports Net BEUI TCP IP NWLink IPX SPX and NWLink NetBIOS transfer protocols Device Configuration e Network Driver Optimization Normal e Full Duplex Auto Select N WAY e Boot PROM Disabled e MediaType Auto Select N WAY e 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink 3C900 adapter card into a PCI slot Connect network cable media to the 3C0M 3C900 card Insert a DOS bootable diskette and power on the machine After booting insert the 3COM Software 3C900 Ethernet drivers disk ver 2 1 and execute A 3C90XCFG E XE
25. pear click on OK 25 At the 3Com NIC Diagnostics ver 1 0 message click on Close 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 26 If you know what your TCP IP settings are click NO and enter the IP settings when prompted If You DO NOT know what your TCP IP settings will be click on YES to Obtain an IP address automatically and continue If you do not have the required information contact your network administrator 27 At the Show Bindings for window accept default entries and click N ext 28 When Windows NT is now ready to start the network click on Next 29 Specify your Computer Name Workgroup or Domain and click on Next If you do not have the required information contact your network administrator 30 After Network has been installed on this computer click on Finish 31 To complete the installation select Yes to reboot your computer 4 Connecting to a Windows NT Server 4 0 Windows NT Workstation 4 0 Version Number 3C900 Rev 1
26. rivers diskette and reboot the machine After windows loads open the NETWORK program group and double click on Network Setup Select the Networks button in the Network Setup dialog box 4 Connecting to a Windows NT Server 4 0 Windows for Workgroups Version 3 11 9 Click on the Install Microsoft Windows Network Option and click OK 10 Click on the Drivers button from the Network Setup dialog box and click on Add Adapter 11 Click OK to accept the default choice of Unlisted or Updated Network Adapter 12 Type the path A WFW311 in the Install Driver dialog box then insert the 3COM 3C900 drivers disk 1 into the floppy drive and click OK If you have an HP preloaded HDD set path to C LANDRV 3C900 DISK 1 WF W311 13 Select 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X in the Unlisted or Updated Network Adapter dialog box and click OK 14 Make sure that the 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X NDIS2 NDIS3 is selected in Network Drivers 15 Accept the applicable Network Protocols and then click on CLOSE 3Com Fast Etherlink XL Etherlink XL Adapter 3C90X NDIS2 NDIS3 Microsoft NetBEUI IPX SPX Compatible Transport with NetBIOS If you do not have the required information contact your network administrator 16 At the Network Setup dialog box click on OK
27. s Win95 System Cabs 20 When prompted insert the 3C900 driver s disk 2 of 2 and click on OK 21 Set the path to A and click on OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 Disk2 22 Click on YES to complete installation and restart the machine Windows for Workgroups 2 Connecting to a Netware 4 11 Server Windows for Workgroups 2 Connecting to a Netware 4 11 Server Requirements HP Vectra with DOS and MS Windows for Workgroups 3 11 installed 3COM Etherlink 3C900 Ethernet card and drivers disk ver 2 1 DOS ODI File Name 3C90X COM Size 59KB Date 12 18 96 DOS and MS Windows for Workgroups 3 11 media Novell Netware 4 11 server that supports Net BEUI NWLink IPX SPX and NWLink NetBIOS transfer protocols Netware client for DOS and MS Windows Device Configuration e Network Driver Optimization Normal e Full Duplex Disabled e Boot PROM Disabled e MediaType 10BASE T e 1 0 Base Address FCCOh PCI e Interrupt Request Level 9 PCI Procedure 1 With the HP Vectra turned off install the 3COM Etherlink IIH 3C900 adapter card into a PCI slot Power on the machine and allow it to boot to a DOS prompt Insert the 3COM drivers diskette ver 2 1 downloaded from 3COM s website and execute 3C90XCFG EXE Select CONFIGURE NIC and verify the resource settings listed above under the heading Device Configuration If changes are requir
28. t Remove the 3com cards driver diskette and restart the machine Windows 95 SR2 should automatically recognize the 3COM 3C900 ethernet card With PCI Ethernet Controller listed click on Next Click on Other Locations and insert the 3C900 driver s disk 1 of 2 1 Connecting to a Netware 3 12 Server Windows 95 SR2 10 Set the path to A and click on OK If you have a Hewlett Packard pre loaded HDD set the path statement to C LANDRV 3C900 Disk1 11 3Com Etherlink XL TPO 10Mb Ethernet Adapter should now be listed Click on Finish 12 When prompted insert the 3C900 driver s disk 2 of 2 and click on OK 13 In the Copying Files window the path should read A If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 Disk2 14 Click on OK to continue the installation 15 Click on OK in order to provide Computer and Workgroup names 16 At the Network dialogue box click on the Identification folder 17 Enter your Computer Name Workgroup and Computer Description And click on Close If you do not have a Computer name Workgroup name and Computer description contact your network administrator 18 At the Insert Disk notification click on OK 19 Set the path to your Windows 95 SR2 media and click on OK If you have an HP preloaded HDD the media is located at C Master
29. verify the resource settings listed above under the heading Device Configuration If changes are required save those changes and exit Remove the 3Com Software driver diskette and reboot the machine When Windows 95 restarts a message will appear that new hardware has been found Insert 3Com Etherlink 3C900 software disk 1 of 2 ver 2 1 10 Click Next to begin hardware wizard on the Update Device Driver Wizard dialog message 4 Connecting to a Windows NT Server 4 0 Windows 95 SR2 11 Click on Other Locations in the Update Device Driver Location dialog box and set path to A then click OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C900 DISK 1 12 3Com EtherLink XL TPO 10Mb Ethernet Adapter should now be listed click on Finish 13 Insert Disk 2 of 2 of the 3Com drivers disks and click OK 14 In Copying Files dialog box set path to A and click OK If you have an HP pre loaded HDD set the path statement to C LANDRV 3C9OO DISK 2 15 Click OK at the Network dialog box to provide computer work group names 16 Specify your Computer Name Workgroup and Computer Description but do NOT press enter If you do not have the required information contact your network administrator 17 Click on the Configuration folder in the Network Dialog Box 18 Click on Add and then

HP 3C900 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents