Hobart ML-104586 User's Manual
Contents
1. FOOD PROCESSORS FP350 FOOD PROCESSOR MODEL FP350 ML 104586 CORPORATION 701 S RIDGE AVENUE TROY OHIO 45374 0001 937 332 3000 www hobartcorp com FORM 19353 Rev D Oct 2000 TABLE OF CONTENTS GENERAL convocada ies ee biet dan se ai dese a 3 INSTALLATION sodi san ta jat ba sgte Mia sb esaddue paul 3 Unpacking whe se sd SEDES athe gee ued eats 3 POCQUOM A Yee SAB eres eb tee lo es 3 Electrical Connection 0 000 eee 3 OPERATIONS terior nenten eet Sar a al 5 CONOIS ei A E el et eel ute be we Oe Rae 4 5 Fitting And Removing The Pusher Plate 5 Fitting And Removing The Cutting Tools 6 Using The Feed Cylinder 002 0 7 Using The Feed Tube ts ssa dat aes oR Re we eerie bo p RHEE 7 Cleaning ora tame tees Fates gee le abet een see da La 8 Cutting Tool Guide 22 at 9 MAINTENANCE sois aa ea OES 11 Replacement Dicing Grids oooocoococoooomoo 11 TROUBLESHOOTING nuca ed dato ed 11 A 12 O HOBART CORPORATION 1995 DE Installation Operation and Care of MODEL FP350 FOOD PROCESSOR SAVE THESE INSTRUCTIONS GENERAL The FP350 Food Processor is used for slicing shredding grating Julienne cutting and dicing vegetables fruits or cheese A worktable a wall rack and a wide range of slicer shredder and dicing plates are available options INSTALLATION UNPACKING Immediately after unpacking the FP350 check for possible shipping dama2. Fig 2 Fig 3 PL 40590 To remove the pusher plate hold the pusher plate handle raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position Take hold of the pusher plate with both hands Fig 2 Rotate pusher plate until the pin on the shaft is out of the slot on the bracket Pull the pusher plate up and away with the right hand FITTING AND REMOVING THE CUTTING TOOLS Slicing Shredding Grating and Julienne Cutting 1 5 6 Using the pusher plate handle raise the pusher plate and swing it to the left so that the feed cylinder is set in the open position Release the feed cylinder lock by turning the lock handle counterclockwise Then swing the feed cylinder out to the right Place the ejector plate on the knife shaft Press the ejector plate all the way down and turn until the plate is in the locked position Select the appropriate cutting tool for the job Place it on the shaft turning until engaged Screw the decoring screw hand tight counterclockwise into position in the cutting tool center Swing the feed cylinder back to the left and turn the lock handle clockwise into locked position Dicing and French Fries 1 2 4 5 Follow Steps 1 through 3 above When dicing place a suitable dicing grid see Cutting Tool Guide in the knife chamber and turn the dicing grid clockwise as far as it will go When cutting straight potato chips place
3. The potatoes may be stacked to cut several at one time For consistent results stack product against the partition wall of the feed cylinder one pile only The large feed cylinder is also used to slice round products such as lemons and tomatoes Position the product against the partition wall of the feed cylinder Fig 6 For best results it is advisable to remove tops and tails from products like lemons limes or onions and place them in the feed cylinder perpendicular to the desired cut A light pressure on the pusher plate is all that is required to give the best cutting results USING THE FEED TUBE Use the feed tube when cutting elongated items such as cucumber leek etc Fig 7 Since the food processor does not stop when the pestle for the feed tube is removed you may use the feed tube for continuous feeding cutting Always use the pestle to push foods through the feed tube PL 40594 PL 40592 PL 40593 PL 40591 Fig 4 Fig 5 Fig 6 Fig 7 CLEANING WARNING TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING Clean the machine immediately after each use Dismantle all removable parts from the machine and wash them in warm water and detergent Rinse thoroughly and wipe dry with a soft clean cloth Allowing food juices to dry on the machine may cause discoloration NEVER clean cutting tools or other aluminum parts in highly alkaline dishwashing soluti
4. the potato chip grid in the knife chamber and turn the potato chip grid clockwise as far as it will go For best cutting results the direction of the potato chip grid blades and positioning of the potato should be as shown in Fig 5 Select the appropriate cutting tool Place it on the shaft turning until engaged Screw the decoring screw hand tight counterclockwise into position in the cutting tool center Swing the feed cylinder back to the left and turn the lock handle clockwise into locked position If you use the wrong combination of dicing grid and slicing tool see Cutting Tool Guide the following may result The feed cylinder cannot be closed The space between the dicing grid and the slicing tool is too large and leads to poor cutting results Removing the Cutting Tools 1 Using the pusher plate handle raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position 2 Turn the lock handle counterclockwise and swing the feed cylinder out to the right 3 Using the wrench supplied loosen the decoring screw in a clockwise direction 4 Remove the cutting tool s and the ejector plate USING THE FEED CYLINDER After the pusher plate is raised prepared products such as potatoes carrots onions lettuce cabbage etc can be placed in the large feed cylinder Fig 4 When cutting French fries with the Julienne cutter place pile the potatoes against the partition wall Fig 5
5. are intact and sharp Provided the blades and grating plates are sharp a light pressure is normally all that is required to yield the best cutting results Make sure the ejector plate is always fitted when cutting With a little force carefully rotate cutting tool clockwise Contact your local Hobart Service Office for any repairs or adjustments needed on this equipment Long term service contracts are available on this and other Hobart products FORM 19353 Rev D Oct 2000 12 PRINTED IN U S A
6. ge If the food processor is found to be damaged save the packaging material and contact the carrier within 15 days of delivery Prior to installation verify that the electrical service agrees with the specifications on the data plate located at the rear of the machine Do not lift the food processor with any hinged or extended parts lift only with one hand on the front carrying handle and the other hand on the rear carrying handle Fig 1 LOCATION The FP350 should be operated on a suitable counter height surface A pan not provided suitable for kitchen use can be used to capture the product at the exit chute ELECTRICAL CONNECTION WARNING THE ELECTRICAL CORD HAS A THREE PRONGED GROUNDING PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE CONTACT AN ELECTRICIAN DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG ELECTRICAL DATA Wall rack for the cutting tools Brush Decoring screw Aw Wrench ge Slicing tool Dicing grid Pusher plate handle Pestle Feed tube Pusher plate Ejector plate Knife shaft Feed cylinder lock handle Knife chamber Carrying handle front Stop Start Carrying handle rear PL 40588 1 OPERATION WARNING ROTATING KNIVES INSIDE ALWAYS USE PUSHER PLATE KEEP HANDS OUT Proper assembly of the FP350 including selection of the appropriate cutters is necessary for correct operation of the f
7. her plate or feed cylinder not Fit pusher plate into proper operating in proper operating position position Pusher plate swung out beside Swing pusher plate into feed cylinder feed cylinder center Fuse or circuit breaker interrupting Check for blown fuses or fuses with power wrong amperage Broken wire or connection Pull electrical cord from receptacle and call your local Hobart Service Office Machine stops while operating JA Pusher plate raised Swing pusher plate into feed cylinder and won t restart center and lower pusher plate Fuse or circuit breaker interrupting Check for blown fuse or fuses with power wrong Amperage Motor overloaded and thermal Thermal motor protection will motor protection has shut machine automatically allow motor to restart off when it has cooled io POSSIBLE CAUSE SUGGESTED ACTION Low output or bad cutting results A Wrong cutting tool used B Wrong combination of dicing grid and slicing tool when dicing space between the two cutting tools is too large C Problem with blade or grating plate D Feeding pressure too heavy E Build up under cutting tool possibly due to ejector plate not being in place or container is full Cutting tool locked to shaft Build up between cutting tool and dicing grid or potato chip grid SERVICE Refer to Cutting Tool Guide pages 9 10 Refer to Cutting Tool Guide pages 9 10 Make sure blades or grating plates
8. nches millimeters are in parentheses Use Fine and Standard Slicers for sliced products and for dicing Soft products like tomato use the FINE SLICER not the STANDARD SLICER FINE SLICER FINE SLICER FINE SLICER FINE SLICER FINE SLICER STANDARD SLICER FINE SLICER CRIMPING SLICER JULIENNE CUTTER JULIENNE CUTTER JULIENNE CUTTER JULIENNE CUTTER Ye 1 5 mm Ye 3 mm 52 4 mm 72 6 mm 10 mm 10 mm HD Slices firm materials Use with 3 10 mm dicing grid As 14 mm When used with dicing grid use only the 3 4 20 mm dicing grid CR 4 5 mm Ripple cuts root vegetables beef potatoes carrots etc 2 2 5 mm Aes 4 5 mm 72 6 mm 10 mm Dicer and French Fry Plates The recommended slicer plate will produce near cube shaped products The DICER grid dimension must be equal to or larger than the SLICER dimension DICER DICER DICER DICER DICER FRENCH FRY 932 7 5 mm 10 mm Y 12 5 mm 15 mm Y 20 mm 10 mm Use with FINE SLICER 7 s2 6 mm 5 2 4 mm Ys 3 mm Ys 1 5 mm Use with STANDARD SLICER s 10 mm 7 32 6 mm 22 4 mm Ys 3 mm Use with STANDARD SLICER s 10 mm 7 32 6 mm 22 4 mm Ys 3 mm Use with STANDARD SLICER s 10 mm 7 32 6 mm 22 4 mm Ys 3 mm Use with FINE SLICER 9 14 mm Use with STANDARD SLICER s 10 mm Soft products may be diced with
9. ons or in excessively hot water This can cause formation of aluminum oxide black DO NOT USE steel wool or sharp objects for cleaning machine surfaces if they become discolored scratched surfaces become hard to keep clean Do not leave the cutting blades in a wet condition when not in use Never clean the machine with a high pressure hose with steam injection equipment orin a dishwasher Always store the cutting tools on the wall racks for safe handling and easy access 1 Remove pestle rinse in lukewarm water 2 Remove the pusher plate and then the feed cylinder rinse in lukewarm water 3 Remove the cutting tool 4 If you have used a dicing grid before removing push the remaining leftovers through the TOP of the dicing grid with the nylon brush Pushing the leftovers through from the underside of the dicing grid may damage the grid 5 Remove the dicing grid and ejector plate rinse in lukewarm water 6 Wipe the knife chamber with a clean damp cloth Wipe dry with a clean dry cloth 7 Return the cutting tools to the wall rack Lower the ejector plate onto the knife shaft Press all the way down and turn until the plate is in the locked position 8 Replace the feed cylinder and the pusher plate CUTTING TOOL GUIDE Slicers PL 51799 2 e PL 51799 1 Crimping Slicer Julienne Cutters PL 51799 4 Fractional sizes are in i
10. ood processor Refer to the Cutting Tool Guide for sizes of cutters and refer to the appropriate operation instructions CONTROLS Fig 1 START Green Push to start STOP Red Push to stop Interlock switches prevent the food processor from operating when the feed cylinder is out of position or the pusher plate is raised above the feed cylinder If these features do not function as described contact your local Hobart Service Office During operation when the pusher plate is fully raised above the feed cylinder the food processor stops and allows the pusher plate to be rotated clockwise for loading To continue operation rotate the pusher plate counterclockwise until it is directly above the feed cylinder As the pusher plate begins to lower into the feed cylinder the food processor will restart you do not need to push the green START switch unless STOP was pressed Always push the red STOP switch before changing cutters or cleaning FITTING AND REMOVING THE PUSHER PLATE 1 To fit the pusher plate you MUST hold it with both hands in the exact positions shown in Fig 2 Hold it with the pusher plate handle to the left of the machine as you face the front Position the pusher plate shaft against the bracket on the food processor 2 Push the pusher plate down on the shaft with your right hand as far as it will go Fig 3 The pin on the shaft of the pusher plate must slide into the slot in the bracket PaO
11. thinner slicer blades than those recommended Graters and Shredders FINE GRATER SHREDDER SHREDDER SHREDDER SHREDDER SHREDDER SHREDDER Grates raw potato for potato pancakes horseradish sauce dry bread hard Parmesan cheese Ac 1 5 mm Ve 2 mm Y 3 mm Ae 4 5 mm 7 a2 6 mm 56 8 mm 10 Grates carrots drv bread almonds nuts Grates carrots drv bread almonds nuts Grates carrots drv bread almonds nuts Grates carrots drv bread almonds nuts soft pizza cheese Grates carrots drv bread almonds nuts soft pizza cheese Grates carrots drv bread almonds nuts soft pizza cheese shreds cabbage MAINTENANCE WARNING TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE Routinely inspect the machine to make sure that it is in proper working order Plates must be clean intact and sharp The knife shaft should be regularly lubricated with a drop of mineral oil NOT COOKING OIL REPLACEMENT DICING GRIDS Depending on usage dicing grids become dull from wear with an average life expectancy from 8 18 months Dicing grids cannot be resharpened and are therefore expendable Replacement dicing grids are available from your local Hobart Service office TROUBLESHOOTING smerom POSSIBLE CAUSE SUGGESTED ACTION Machine will not start A Feed cylinder not locked in correct Make sure feed cylinger is locked position correctly B Pus
Download Pdf Manuals
Related Search