Harbor Freight Tools Digital Inspection Camera Product manual
Contents
1. breakage and any other conditions that may affect its operation Store the Camera cables and accessories in a locked area out of the reach of children WARNING Handling the cord on this product will expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling California Health amp Safety Code 25249 5 et seq People with pacemakers should consult their physician s before use Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator There are no user serviceable parts Camera service must be performed only by qualified repair personnel Item 61839 For technical questions please call 1 888 866 5797 Page 3 Specifications Battery Type Handheld Display Unit 32 F to 113 F Operating Temperature Imager Head Ingress IP67 Protected against the effect of Protection Rating immersion between 15cm and 1m Imager Head and Cable 14 F to 176 F Operating Temperature Video Output RCA Cable C E N Coe Page 4 For technical questions please2. call 1 888 866 5797 Item 61839 FE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CENA Coe Item 61839 For technical questions please call 1 888 866 5797 Page 5 Setup Before Use beginning of this document including all text under subheadings therein 1 Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the before set up or use Components RCA Video Out Cable Port Connector Display Screen Cable Handheld _ Display Unit Imager _ Head with Light Hook Mirror Magnet Figure A Page 6 For technical questions please call 1 888 866 5797 Item 61839 Installing Batteries CAUTION Position batteries in proper polarity and do not install batteries of different types charge levels or capacities together The battery compartment is located on the bottom of the handle 1 Slide the Battery Cover off remove the battery case insert four AA batteries not included Tool Set Up AWARNING Slide the battery case back in and replace the Battery Cover Figure B Battery Cover TO PREVENT SERIOUS INJURY FROM ELECTRICAL SHOCK Make sure that the Camera is OFF before performing any procedure in this section 1 Connecting Cable a Carefully
3. push Cable s key into Cable Connector s slot b Turn Cable Connector counterclockwise until the Cable and Cable Connector are securely attached 2 Disconnecting Cable a Turn Cable Connector clockwise until the Cable and Cable Connector are detached b Remove Cable Slot Key Cable Connector Figure C Attaching Accessories a Hold the accessory against the Imager Head placing the Hook in the hole b Match the slot on the Sleeve to the accessory then slide the Sleeve down the Imager Head until it covers the Hook Sleeve Accessory om Imager Head Figure D Connecting to External Monitor with RCA Cable Plug one end into the RCA Video Out Port on Camera then plug other end into RCA Video In Port on monitor Item 61839 For technical questions please call 1 888 866 5797 Page 7 Operating Instructions 1 Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product AWARNING TO PREVENT SERIOUS INJURY AND DEATH Always wear eye protection Wear ANSl approved safety goggles during use Before inspecting walls shut off the circuit breakers to the whole house Before inspecting pipes that may contain an electric charge have them checked by a qualified electrician Before inspecting an engine turn off the automobile Handheld Display Unit Controls Power Brigh
4. O THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Parts List Part Description Qty Cable with 8 5mm Imager Head tt RCA Cabe S O 45 Mirror Accessory O 1 Hook Accessory _ 1 Magnet Accessory tt 7 Record Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Item 61839 For technical questions please call 1 888 866 5797 Page 11 Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may n
5. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference i i N C O ITEM 61839 DIGITAL INSPECTION CAMERA p Visit our website at http www harborfreight com _ Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2014 by Harbor Freight Tools All rights reserved R gt F No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Important Safety Information Work Area Safety 1 Keep your work area clean and well lit Cluttered benches and dark areas may cause acci
6. dents Operate the Camera in a well ventilated work area Do not operate the Camera in explosive atmospheres such as in the presence of flammable liquids gases or heavy dust Keep a fire extinguisher suitable for gasoline chemical electrical fires nearby Keep bystanders children and visitors away while operating the Camera Electrical Safety 1 Before inspecting walls shut off the circuit breakers to the whole house 2 Before inspecting pipes that may contain an electric charge have them checked by a qualified electrician 3 Before inspecting an engine turn off the automobile 4 Donotuse the Camera while standing in water 5 Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators Page 2 6 8 For technical questions please call 1 888 866 5797 This product is not a toy Do not allow children to play with or near this item Use as intended only Inspect before every use do not use if parts are loose or damaged Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement Do not expose the Handheld Display Unit to rain or wet conditions Water entering the Handheld Display Unit will increase the risk of electric shock Do not place the Imager Head and Cable into any place that may contain a live electric charge or moving parts which increases th
7. e batteries before storage on a clean cloth to remove any oil 3 grease or dirt from the Camera especially on the buttons and ports being careful to not put excessive pressure on the Display Screen Store the Camera cables and accessories in a locked area out of the reach of children Troubleshooting Problem Possible Causes Likely Solutions Display is on but does 1 Cable connection loose 1 Check that cable is connected not show image 2 Imager Head is dirty 2 Clean Imager Head Light is dim at maximum brightness Display turns itself off Low Batteries Replace Batteries Camera will not turn on Follow all safety precautions whenever diagnosing or servicing the tool Disconnect power supply before service Page 10 For technical questions please call 1 888 866 5797 Item 61839 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS T
8. e risk of electric shock Make sure your hands are dry before operating the Camera or charging the battery Item 61839 Camera Safety 1 The Handheld Display Unit is not waterproof The Imager Head and Cable are rated to IP67 See Specifications on page 4 Do not use the Camera if condensation forms in the Imager Head Let condensation evaporate before use Do not submerge the Imager Head and Cable into corrosive substances such as drain cleaner Do not get gasoline or oil on the Imager Head and Cable Personal Safety 1 Wear ANSI approved safety goggles during use Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Do not use the Camera while tired or under the influence of drugs alcohol or medications A moment of interruption can result in serious personal injury Do not over reach Keep proper footing and balance at all times Proper footing and balance enables better control of the Camera in unexpected situations Do not use the Camera for personal inspection or medical use in any way This is not a medical camera Service Do not use excessive force to insert or withdraw the Imager Head and Cable Do not use the Camera near moving machinery Do not place the Camera on any unstable cart or surface Handle the Camera with care If the Camera is dropped check for
9. ot apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state C E N Coe 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 5797
10. ten Light Figure E Page 8 For technical questions please call 1 888 866 5797 Item 61839 General Operating Instructions Live Viewing View on Display Screen or use RCA cable to view on external monitor 1 Press the Power button to 3 Flip Image Press the turn the Camera on Flip Image D button to flip 2 Adjusting Light Press Left x5 image horizontally and vertically button to dim and turn off light i 4 When finished press the Power button Press Right button to turn on to turn the Camera off then clean light and increase brightness and store according to Inspection and Maintenance on page 10 Item 61839 For technical questions please call 1 888 866 5797 Page 9 Inspection and Maintenance Procedures not specifically explained in this manual A must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM ELECTRICAL SHOCK Make sure that the Camera is OFF before performing any procedure in this section TO PREVENT SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment If abnormal noise or vibration occurs have the problem corrected before further use Inspection 1 BEFORE EACH USE inspect the e cracked or broken parts and general condition of the tool Check for any other condition that may e condensation in Imager Head affect its safe operation e cracked or damaged Cable Cleaning and Storage 1 AFTER USE use a mild detergent 2 Remov
Download Pdf Manuals
Related Search