Harbor Freight Tools 92966 User's Manual
Contents
1. 17 this product was designed It will do the job better and more safely at the rate for which it was intended Do not modify this product and do not use this product for a purpose for which it was not intended Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically nonconductive clothes and nonskid footwear are recom mended when working Wear restrictive hair covering to contain long hair Do not overreach Keep proper footing and balance at all times Do not reach over or across running machines Maintain tools with care Keep needles sharp and tools clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords periodically and if damaged have them repaired by a qualified technician The handles must be kept clean dry and free from oil and grease at all times Disconnect power Always turn the machine off and if possible disconnect the power plug of the machine from the receptacle before adjusting repairing or cleaning the machine leaving the machine unattended tilting the machine head or removing the V belt Remove adjusting keys and wrenches Check that keys and adjusting wrenches are removed from the machine work surface before plugging it in Avoid unintentional starting Be sure the switch is in the Off position when not in use and before plugging in Stay alert Watch what you are doing use common2. sense Do not operate when you are tired Check for damaged parts Before using any product any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part that is damaged should be properly repaired or replaced by a qualified technician Do not use if any switch does not turn On and Off properly Guard against electric shock Prevent body contact with grounded surfaces such as pipes radiators ranges and refrigerator enclosures Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are available from Harbor Freight Tools Do not operate tool if under the influence of alcohol or drugs Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Use proper size and type extension cord If an extension cord is required it must be of the proper size and type to supply the correct current to the tool without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the tool This tool requires use of an extension cor
3. to the belt until it just barely doesn t touch it gap or less see Figure B above Tighten the Wood Screws 10 22 from step 22 above 24 Put the Belt Cover back on the Sewing Machine before use Setup and Adjustment Section Contents SECTION PAGE Bobbin Winder OD Sa OM EE 9 DS IC BOBDN ln RE 9 Needle FAC un 10 Threading the Ten 10 Mer ESAO D 11 Reversing Sewing ER IN de EE 11 Needle Thread Ienson sss sese eee 11 Bobbin Thread Tension WE 11 Thread Take Up eae BEE 11 Thread Take Up ea 12 Presser sla EE 12 Proosa Bar sel EE 12 Food TIMI EE 12 Fed DOO TAN la 13 Needle to hook Timing EE 13 SKU 92966 For technical questions please call 1 800 444 3353 Page 8 Caution To properly break in your new sewing machine and avoid possible damage to the machine sew at moderate to slow speeds for the first 15 minutes of use Bobbin Winder Operation The Bobbin Winder has two positions ON and OFP OFF Position The Bobbin Winder won t contact the belt WARNING Shut the machine off completely before ON Position This position is with the Connecting Rod 10 6 Winding Thread Onto the Bobbin 1 Setting the Bobbin into the Bobbin Case 1 Setup and Adjustment The Bobbin Winder assists in winding thread onto the Bobbin working around the needle or other moving parts pressed as shown in Figure C The Shaft on the Bobbin Winder gt will spin windin
4. CHICAGO SEWING MACHINE SINGLE NEEDLE tt 21 92966 ASSEMBLY SETUP AND ADJUSTING INSTRUCTIONS 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2005 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Specifications Machine Type Heavy duty industrial sewing machine high speed single needle lock stitch V belt driven Action Foot pedal operation along with a knee and manual lifting arm for presser foot Presser tension adjustment Feed Type Link style needle feed reduces slippage Sewing Directions Forward and reverse feed 20 3 Lx 10 H 2 Screwdrivers 3 Bobbins Accessories Small lubricating bottle with tip Spare needles Power Switch Table Stand Kit Table Stand Kit Model 03929 not included Stitching Speed 2 000 SPM Motor Type Clutch motor 1 725 RPM 5 8 2 9 amps 110 220 VAC 60 Hz single phase Sewing Thickness up to leather Overall weight 56 Ib Caution Make certain that the voltage switch on the motor is set correctly for your use See page 6 This Machine requires oil to be added before use se
5. Feed driving shaft bushing Screw Feed rocker shaft Feed driving shaft bushing Screw Thrust collar Thrust collar Screw Feed driving shaft crank Screw Shaft Feed crank Feed crank moving shaft Screw Moving crank Oil wick Feed Lifting shaft bushing Feed lifting shaft Feed lifting shaft bushing Screw Washer Washer Thrust collar Screw Feed lifting shaft crank Feed lifting pin Screw Screw Snap ring ASSEMBLY DIAGRAM 4 FEED MECHANISM COMPONENTS te For technical questions please call 1 800 444 3353 Page 17 SKU 92966 PARTS LIST 5 Presser foot lift bar Screw Presser foot lift bar Oil seal Lever left Thread releasing cam Screw Screw Knee lifter drawing bar Screw Thread releasing lever knee lifter lever right Spring Screw Connecting rod Pin presser bar Bushing Presser bar presser bar Guide Screw Spring Screw Nut Screw Thread guide Screw Presser foot ASSEMBLY DIAGRAM 5 PRESSER ARM ex T 1 H i i U U U 1 h t 1 1 U 1 1 t D H T 1 DH e For technical questions please call 1 800 444 3353 Page 18 SKU 92966 ASSEMBLY DIAGRAM 6 FEED MECHANISM COMPONENTS PARTS LIST 6 Description z LA tytn L E b Aa A A h h e Ww t t t to ta U to Ua w LA EA EA LA EA LA LA KA KA EA de Ka mat ee pt K pt e C AD OO C OR L a Ua UA d EE LQ LA O MO OO MIN Lh LAA LA en CO MO GO IA LO LA
6. M 2 NEEDLE FEED MAIN SHAFT Part No Description Screw Feed drive cam Screw ake up thread Take up thread con t Thread take up crank Needle bearing Endscrew Left hand Needle bar crank connecting rod Needle crank Needle bar adaptor Screw Needle bar crank screw Screw Set screw Rubber bar upper bushing Felt Rubber plug Needle bar shaft cover Needle bar Thread finger Needle Screw Rail Screw Sliding block a a ubber plug Cae Screw Front bushin Middle bushing Screw Main shaft thrust collar Main shaft thrust collar Hand wheel Screw Thrust collar Feed crank connecting rod Feed y connecting asm Vertical shaft Bevel gear Vertica shaft bevel gear upper Screw Rock shaft bevel gear Vertical shaft bevel gear lower Vertical shaft bushing upper complete Verthcal shaft bushing lower complete Screw Hook driving shaft Screw Oil wick Hook driving shaft thrust collar Screw Oil washer Hook driving shaft thrust collar left Screw Spring Hook driving shaft thrust collar rish Oil tube Screw Spring Frame Screw Hook Asm Rotating hook position finger Screw Bobbincase Bobbin T H t 1 1 E t G L i l H 1 H i ba BA RI BA DADS NNN D Do HAHAHAHAHAHAHA Da NNN NNN NNN ANN Nb md d IO Ca Ch E C Ch Ca C C A ULA GA L L L LA LL P op LA LA COU OO SICA LP A LAAL COD OO J C L P bo COMO GO J O AB CO hd COM t D t 1 L U t 1 1 1 LA LAA LAO LAA LA LOLA AHAHAHAHAHAHAH LAA n be
7. Remove the Rubber Plug C on the Face Plate B Loosen the set screw underneath 2 Manually adjust the Presser Bar height and the angle of the Presser Foot The normal position is 6 mm clearance 3 After adjusting retighten the Set Screw and replace the Rubber Plug C Check to ensure that the presser foot is not loose 4 Manually turn the Hand wheel through a full cycle to verify that the presser foot will not contact the walking foot or obstruct the needle If it does readjust the Presser Foot Adjusting the Feed Timing 1 Loosen Set Screws 2 and 3 on the Feed Eccentric Cam 1 and properly position the Eccentric Cam Retighten the Set Screws 2 Tloadvance the feed timing in order to prevent uneven material feed move the Feed Eccentric Cam up ey LL Ta clockwise 3 To delay feed timing and increase stitch tightness move Feed Eccentric Cam down counterclockwise SKU 92966 For technical questions please call 1 800 444 3353 Page 12 Adjusting the Height of the Feed Dog The Feed Dog is factory adjusted If the Feed Dog juts out too much puckering may result when sewing lightweight materials To adjust the height of the Feed Dog 1 Move the Feed Dog to the front end of the throat plate Loosen Screw A of Crank Move the Feed Dog B up or down to make the adjustment Tighten Screw A being careful not to over tighten Adjusting Needle to hook Timing 1 Turn
8. a COM GO 4 G Lh Lutte MO GO 4 GL LM LA e CH For technical questions please call 1 800 444 3353 Screw Nut adjusting screw Bracket Bushing Screw Presser foot lift shaft Link adjusting crank Screw Link complete Screw Eccentric cam Split ring Screw Washer Nut Presser foot feed crank in Screw Spring Guidepin Set plate Screw Pin Guide plate Screw Needle bearing Guide shaft Screw Crank Pin Rear bushing Screw Rear crank Screw Nut Link Screw Front bushing Crank shaft complete Fork lever Nut Walking foot lever walking foot bar Holder Screw Walking foot Shim Presser plate Screw Screw Pin Washer walking foot Link Presser foot swing shaft Spacer Screw a K ee rk e eee mee A HA re ND a eet a pene eke ae be re LD a e peat e pre bn HA e K K K Ke K Ke K Kt K K LA a K a Ke K e pet BD E et e et Page 19 SKU 92966 ASSEMBLY DIAGRAM 7 LUBRICATION COMPONENTS Description Lubrication oil pump Oil pump holder Screw Oil pump shaft Oil pump cover Oil return pump plunger Spring Cover Screw Frame Screw Oil wick set plate complete Oil return tube holder Felt Spring Frame Oil tube Oil pump screen Screw Washer oil pump Screw For technical questions please call 1 800 444 3353 Page 20 SKU 92966 ASSEMBLY DIAGRAM 8 OIL RESERVOIR PARTS LIST 8 Description Oil reser
9. d with up to 10 amps capability SKU 92966 For technical questions please call 1 800 444 3353 Page 3 up to 50 feet with wire size rated at 18 AWG Longer extension cords require larger size wire 18 Maintenance For your safety service and maintenance should be performed regularly by a qualified technician 19 People with pacemakers should consult their physician s before using this product Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker 20 Keep hands away from the needle when you turn the power switch on or while the machine is operating 21 Do not place your fingers into the thread take up cover while the machine is operating 22 During operation never place your head hair or hands in the proximity of the hand wheel V belt bobbin winder or motor 23 Do not operate the machine with any safety guards removed 24 This machine shall only be operated by appropriately trained operators 25 For your personal protection we recommend you wear ANSI approved safety glasses when using the machine 26 If oil or grease comes in contact with your eyes or skin immediately wash the affected areas and consult a physician 27 Tampering modifying or altering any device aside from the cord and plug by a licensed electrician on the machine is prohibited and will void manufacturer s warranty 28 Repair adjustment and specific maintenance shall o
10. e highest point of its stroke 4 Loosen Screw 2 and hold Needle 1 with its indented part facing toward the Presser Bar 5 18 Insert the needle and push it up until it will go no farther 6 While holding in place securely tighten Screw 2 Threading the Machine Head Set the thread spool on its holder and guide the thread through the machine as illustrated to the left The numbers in the illustration indicate the threading sequence SKU 92966 For technical questions please call 1 800 444 3353 Page 10 Adjusting the Stitch Length 1 To increase the stitch length turn the Stitch Length Dial 1 to the desired number in millimeters as indicated under the scale dot A on the machine 2 To decrease the stitch length turn the Stitch Length Dial 1 to the desired setting The Feed Lever 2 may require adjustment to allow the Dial to move Reversing Sewing Direction Depress and hold the Feed Lever 2 to sew in a reverse direction After the Lever is released sewing direction will automatically return to forward Adjusting the Needle Thread Tension 1 Turn Tension Adjustment Knob 1 clockwise A to increase thread tension 2 Turn Tension Adjustment Knob 1 counterclockwise B to decrease thread tension Adjusting the Bobbin Thread Tension 1 Turn the Tension Adjustment Screw 2 clockwise A to increase bobbin tension 2 Turn the Tension Adjustment screw 2 counterclockwise B to d
11. e page 6 for details Save This Manual You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dry place for future reference Safety Warnings and Precautions WARNING When using tool basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment Read all instructions before using this tool 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools in damp or wet locations Don t expose to rain Keep work area well lighted Do not use electrically powered tools in the presence of flammable gases or liquids 3 Keep children away Children must never be allowed in the work area Do not let them handle machines tools or extension cords 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right product for the job Do not attempt to force a small product or attach ment to do the work of a larger industrial tool There are certain applications for which REV 07 05 SKU 92966 For technical questions please call 1 800 444 3353 Page 2 10 11 12 13 14 15 16
12. ecrease bobbin tension Changing the Thread Take up Spring Stroke and Pressure 1 Loosen Set Screw 2 2 To Increase the stroke turn the Tension Knob Screw 3 clockwise A 3 To decrease the stroke turn the Tension Knob Screw 3 counterclockwise B 4 Loosen Set Screw 2 and pull out the Tension Arm 5 5 Loosen Set Screw 4 and remove the Tension Knob Screw 3 6 Turn the Tension Knob Screw 3 clockwise A to increase pressure or turn counterclockwise B to decrease pressure 7 Replace Tension Knob Screw 3 tighten Set Screw 4 and replace the assembly SKU 92966 For technical questions please call 1 800 444 3353 Page 11 Adjusting the Thread Take up Stroke 1 When sewing heavy weight materials move the Thread Guide 1 to the left A to increase the length of thread pulled out by the Thread Take up 2 When sewing lightweight materials move the Thread Guide 1 to the right B to decrease the length of thread pulled out by the Thread Take up 3 The normal setting is when the marker line C on the Thread Guide 1 is aligned with the center of the screw Setting the Presser Foot Pressure 1 Loosen Nut A and turn the Presser Spring Regulator clockwise a to increase Presser Foot pressure 2 To decrease Presser Foot pressure turn the Presser Spring Regulator counterclockwise b 3 After adjustment tighten Nut A Adjusting the Presser Bar Height 1
13. g thread onto the Bobbin Place a Bobbin onto the Bobbin N Winder Shaft 10 3 as shown W at point din Figure C right Route the Thread from the Spool not shown up through Fe the Thread Guide Tube 10 39 point a the hole in the Thread Tension Bracket Assembly 10 15 b over and under the far side of the Tension Disc 10 17 c and connect it to the Bobbin d See Figure D right While the Connecting Rod 10 6 is pressed as shown in both Figures Cand D the Bobbin Winder will be in the ON position and the Bobbin will fill with thread When finished release the Connecting Rod and the Bobbin Winder will reset to the OFF position Hold the Bobbin so that the thread est je to the left and push the Bobbin into its case Feed the thread through slit A and pull the thread in direction B By doing so the thread will pass under the tension spring and exit at notch B Verify that the Bobbin rotates in the direction of the arrow when thread C is pulled SKU 92966 For technical questions please call 1 800 444 3353 Page 9 Attaching the Needle Replacement Needle Type 135 X 17 1 Unplug the Power Cord from the electrical outlet 2 Select a proper needle size according to the thread count and type of material being sewn 3 Turn the Hand Wheel until the needle bar reaches th
14. he end of the Upper Column 10 26 SKU 92966 For technical questions please call 1 800 444 3353 Page 7 Mounting the Bobbin Winder Note Unless indicated otherwise all parts referred to in this set of instructions are listed in the Bobbin Winder amp Thread Stand Unit Parts Listfound on page 23 During assembly it will be helpful to refer to that list and the diagram above iton the same page 20 Remove the Belt Cover part 8 27 on page 21 Swing the i sewing machine so the base is in the operating position resting on the table Set the Bobbin Winder to the ON Position see ON Position below 21 Make sure the Bobbin Winder is in the ON position Position the Base Bobbin Winder Base Assembly 10 1 so that the Thread Winder Assembly 10 4 lines up with and just touches the belt Mark pilot hole locations on the table at the far end of each of the two channels in the Base as indicated in Figure A y K 22 Set ihe Base 10 1 aside and swing the sewing machine out of the way Carefully drill straight pilot holes for each of p the two locations marked above Place the base in location and secure using two Wood Screws 10 22 and Washers Z 10 23 Leave the Screws just loose enough to allow the Base to slide 23 Swing the Sewing Machine back into it s operating position Put the Bobbin Winder in the OFF position see OFF Position below Slide the Bobbin Winder Assembly close
15. her 10 33 over the end of the Rod and thread on and tighten a Nut 10 34 Place the Spool Support 10 42 over the Lower Column 10 32 about halfway down Insert a Screw 10 27 and Nut 10 43 through the Support Note The Support has tabs that hold onto the corners of the Nut to make tightening easier When assembling place the Nut on the side with these tabs Tighten the Screw Insert the threaded end of the Spool Pin 10 36 through one of the holes in the top of the arm of the Spool Support 10 42 Place a Washer 10 28 and Nut 10 31 over the end of the Pin and tighten Place the Spool Rest 10 37 Spool Mat 10 38 and the Spool Vibration Stopper 10 35 over the end of the Spool Pin Repeat this step for both of the Spool Pins 10 36 Place the Column Pipe Connector 10 29 over the top of the Lower Column 10 32 until the Rod is about halfway through the Connector Place a Screw 10 30 and Nut 10 31 through the bottom hole in the Connector and finger tighten Place the Upper Spool Rest Rod 10 26 into the top of the Column Pipe Connector 10 29 Place a Screw 10 30 and Nut 10 31 through the top hole in the Connector Tighten all of the Screws and Nuts in the Connector Place the Thread Hanger 10 24 about halfway over the top of the Upper Column 10 26 Insert a Screw 10 27 and Nut 10 43 through the Hanger as explained in the note in step 14 above Tighten the Screw and place the Column Cap 10 25 over t
16. n Kea K be K KA prt K Ka MD OG J ON Af fa LAAF CNA D Gob vet CMD 00 ST CL LOLA Kak CMD OD ON LN Pa GO L r C i 1 t 1 i t 1 U L 1 i t i 1 1 t t t H D D 1 I t H H H H 1 i i 1 1 L AHAHAHAHAHAHAH HAHAHA HAHAHAHAHA NNN NN NN HAHAHAHAHAHAHA HAHA LA v be Ka e bi rg PA a Fal Ka Sech bal ea Sen Ke Eet K Kra eot Ket t been lora Sr LD e k rh Kar Ken Sen DD t rn M REV 01 06 SKU 92966 For technical questions please call 1 800 444 3353 Page 15 SKU 92966 ASSEMBLY DIAGRAM 3 FEED MECHANISM COMPONENTS 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 3 10 3 11 3 12 3 13 3 14 3 15 3 16 3 17 3 18 3 19 3 20 3 21 3 22 3 23 3 24 3 25 3 26 3 27 3 28 3 29 For technical questions please call 1 800 444 3353 PARTS LIST 3 oy Feed lifting shaft crank Crank connecting Crankshaft Screw Thrust collar Screw Thrust collar Screw Rubber Screw O ring Stitch length dial Screw Rubber washer Stop shaft Spring Reverse feed contro lever Feed reverse shaft Feed reverse shaft O ring Screw Screw Washer Feed reverse crank Feed reverse crank return plate Feed reverse crank move plate Spring Screw Spring stand l 1 l l l 2 l I l l l 2 l l l l l l l 2 l l l I I I i Page 16 SKU 92966 PARTS LIST 4 Description Feed crank Screw Feed holder Feed dog Screw Feed Holder shaft Screw Feed rocker shaft Oil wick
17. nly be performed by a quali fied service technician Alteration or replacement of the 3 prong grounded electrical plug provided with the machine must only be performed by a licensed electrician This machine must be properly grounded Note Performance of this tool may vary depending on variations in local line voltage Extension cord usage may also affect tool performance Warning The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Unpacking When unpacking check to make sure that the parts shown in the photo on the following page are included Note that the machine table shown is not included and must be ordered separately If any parts are missing or broken please call Harbor Freight Tools at the number on the cover of this manual as soon as possible SKU 92966 For technical questions please call 1 800 444 3353 Page 4 He sh vm B i CS N Sewing Machine k T Table Stand and Se Top not provided WM Motor z Knee Lifting Arm J S for Presser Foot Assembly Power Switch The assembly instructions describe mounting the Single Needle Sewing Machine Model 92966 to the Table Stand Model 03929 not included In order to complete this procedure you m
18. oltage Switch left for 110V switch right for Be Wi 220V For 220 V the power gf 4 plug must be rewired by a ds RW a ualified technician o i Note Receptacle e CCED for 6 volt work light not included we 11 Place the V belt around the Sewing Machine Pulley through the slot in the table top and around the Motor pulley Attach the Pulley Safety Cover 12 Tighten the V belt tension by adjusting the long bolt and nut at location K The proper tension is reached when the V belt can only be deflected 1 2 inch 13 Mount the Power Switch under the table top on the operator s side Use the supplied hardware SKU 92966 For technical questions please call 1 800 444 3353 Page 6 Power Switch Mounting the Thread Stand 14 15 16 17 18 19 Note The Thread Stand is designed to be mounted on the Table Stand Kit Model 03929 not included Unless indicated otherwise all parts referred to in this set of instructions are listed in the Bobbin Winder amp Thread Stand Unit Parts List found on page 23 During assembly it will be helpful to refer to that list and the diagram above it on the same page Locate the large hole in the far right corner from the location that the operator will be seated of the Table not included Place the Rubber Washer 10 41 and Washer 10 33 onto the Lower Spool Rest Rod 10 32 and insert the Rod into the hole mentioned above Place another Was
19. ou with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product WARRANTY CIN WZ ZG GA Ca ZAIN SIC ZAIN SS KINO N A sl se C G Page 24
20. rillo CA 93011 e 800 444 3353 gd a For technical questions please call 1 800 444 3353 gt WA ANEA CHICAGO LIMITED 90 DAY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the KES gt period of ninety days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase EK price if we cannot readily and quickly provide y
21. s D e always include the list title item number and description i Bod fara and page number For example to order the first part D Le ar n Bart e N J from page 14 list you would state Parts List 1 Arm Bed Item 1 1 Arm Page 14 NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PARTS LIST 1 Part Description 1 om _ Description om Se Adjusting Bracket Servo motor 1 13 Screw 8 400 Slower replacement for stock motor not shown optional SE She optional PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO REV 01 07 SKU 92966 For technical questions please call 1 800 444 3353 Page 14 ASSEMBLY DIAGRA
22. the Hand Wheel to bring the Needle Bar C down to the lowest point of its stroke Remove the Rubber Plug A then loosen the Set Screw B Move the Needle Bar C down until the Eye of the Needle D lines up with the inside surface of the bobbin case holder E Tighten the Set Screw B and replace the Rubber Plug A Turn the Hand Wheel until the needle descends about 2 5 mm For typical hook timing the hook should be directly about 1 2 mm above the upper edge of the needle eye at this point After making the adjustments in steps 3 and 4 align the Hook Blade point 5 with the center of the needle 4 Provide a clearance of 001 to 004 0 04 to 0 1 mm between the needle and the hook This clearance is less than 1 64 almost touching Securely tighten the three Set Screws If the clearance is too small the tip of the hook will be abraded If it is too large it will lead to skip over Maintenance Machine adjustments should only be performed by a qualified technician Check the oil level weekly when the machine is used daily Add sewing machine oil as required to the high level marking Clean the machine with a clean damp cloth Do not use solvents or thinners When not in use cover the machine and store in a clean and dry location SKU 92966 For technical questions please call 1 800 444 3353 Page 13 ASSEMBLY DIAGRAM 1 ARM BED Can MOQ O A 29 NOTE When ordering parts from the following list
23. ust first purchase and assemble the Table Stand Kit Model 03929 1 Locate four corner rests in the rectangular hole of the Table Stand where the machine will sit Operator Side Hinge Side 2 Place two rubber seats A on the operator side and secure with supplied hardware C See figure 1 3 Place two rubber hinge rests B on the hinge side and secure with supplied hardware C 4 Seat the Oil Pan D on the corner seats A See figure 2 Insert Hinges E into the machine bed See figure 3 6 Fit the machine head s hinges to the rubber hinge rests B before placing the machine head on the corner seats See figure 4 SKU 92966 For technical questions please call 1 800 444 3353 Page 5 7 Ti the machine back to expose the Oil Pan D See figure 5 8 Eil the Oil Pan with sewing machine lubrication oil 7 white oil to the high mark A A G get SA OK oy a Add more oil when the level is to the low mark B After lubrication and during opera tion oil splashing can be seen through the Oil Sight Window H 9 Lower the machine head to the table top 10 Mount the Motor to the underside of the table top as shown below Use the supplied hardware Note Top switch determines rotation Switch left for counter RO clockwise switch right e for clockwise rotation ee 2 e Note Motor is 110 220V single Phase Disconnect 4 Ji power and flip switch to desired v
24. voir Screw Washer Washer Gasket large Hinge pin Spring Frame Screw Nut Screw Knee lifter prop bar Bent rod Screw Screw Bell Bell bracket Screw Pad Screw Washer Belt cover top Screw Label Screw Screw Belt cover Belt cover asm For technical questions please call 1 800 444 3353 Page 21 ASSEMBLY DIAGRAM 9 ACCESSORIES Description 9 1 Machine hinge plate asm 2 9 2 Machine hinge plate 2 9 4 Washer Large 2 9 5 Washer small 2 9 6 Oil can small 9 7 Magnet 9 8 Screwdriver Large I 9 9 Screwdriver Medium I 9 10 Screwdriver small 9 11 Spanner L 9 12 Oil can 9 13 Dust cover 9 14 Needle 4 SKU 92966 For technical questions please call 1 800 444 3353 Page 22 ASSEMBLY DIAGRAM 10 BOBBIN WINDER AND THREAD STAND PARTS LIST 10 BOBBIN WINDER Part Description Com SKU 92966 For technical questions please call 1 800 444 3353 THREAD STAND Part Description Com Page 23 L TA V K eal CY VsracfN V Wy Kb bs X Sr RQ SN BY Ka Wi Se N V V N V lt c A KS 15 K SKU 92966 N VATV Y TN VW TN VT LV V TN VW TN V a TN V a ANI ZIN CA Ny CZ e CANN CANS CZ We CZ NSS CANS IRI NET DC KEN KEN KT NET OC KEN A gt ULL SN This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd lt PO Box 6009 e Cama
Download Pdf Manuals
Related Search