Harbor Freight Tools 29 In Heavy Duty Tool Stand Product manual
Contents
1. Nuts 1420 5 16 18 Depending on the tool you are mounting the drawings on page 5 through 9 show assembly according to the Top Braces for that particular tool Note The tool description is at the top of each drawing This will identify the tool to be mounted for that configuration UNIVERSAL BENCH POWER TOOLS Fits the Following 29 Heavy Duty Tool Stand 8 Drill Press 4 1 8 Jointer Planer 9 Drill Press 13 Scroll Saw 10 Drill Press 15 Scroll Saw 10 Band Saw 16 Scroll Saw 12 Band Saw 10 Miter Saw 4 Belt amp 6 Disc Sander not for all models In the event your machine does not fit simply put plywood or particle board on the surface of the Top Braces 8 9 10 amp 11 SKU 95128 For technical questions please call 1 800 444 3353 Page 4 TOOL STAND ASSEMBLY STEP 1 T Install one Rubber Sleeve 1 onto each Leg 2 See Figure 1 2 Assemble front and rear sections as shown in Figure 1 below Insert the Carriage Bolts 4 through the Legs 2 through the Braces and then into the retractable slots Fasten each piece with a Washer 5 and Hex Nut 6 Tighten the Nut 3 Assemble the two Top Sides 8 to the Top Front amp Rear Braces 9 amp 11 See Figure 1 below STEP 2 1 Assemble this step according to the configuration of the tool you are mounting See Figure 1 2 Once you have everything assembled be sure to tighten all hardware securely CONFIGURATION FOR 13 SCRO2. or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRAN TIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd e PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 95128 For technical questions please call 1 800 444 3353 Page 11
3. D SAW One Top Side 8 and one Top Cross Brace 10 in holes marked D P W amp Y 4 holes Figure 3 STEP 3 1 In some cases the Top Cross Brace 10 will change positions depending on the tool you are mounting Assemble according to the configuration of the drawing per taining the tool you are using See Figure 3 SKU 95128 For technical questions please call 1 800 444 3353 Page 7 CONFIGURATION FOR 8 DRILL PRESS 9 DRILL PRESS e 10 DRILL PRESS DRILL PRESS Top Cross Brace 10 in holes W amp Z 2 holes Figure 4 STEP 3 3 In some cases the Top Cross Brace 10 will change positions depending on the tool you are mounting Assemble according to the configuration of the drawing per taining the tool you are using See Figure 4 SKU 95128 For technical questions please call 1 800 444 3353 Page 8 CONFIGURATION FOR 4 1 8 JOINTER PLANER 4 1 8 JOINTER PLANER One Top Side Brace 8 in holes marked A E M amp Q 4 holes Top Cross Brace 10 not used Figure 5 MAINTENANCE 1 Wipe down Tool Stand after each use with a dry cloth and store in a secure place 2 If any oil or grease is on the Tool Stand clean with a cleaning solvent and wipe area dry SKU 95128 For technical questions please call 1 800 444 3353 Page 9 PARTS IDENTIFICATION Part Description ay Leg e henas SSCS 7 Bonom Front amp Rear Bras gt E E e 10 Top Cross Brace fo 11 Top
4. LCENTRAL MACHINERY 29 HEAVY DUTY TOOL STAND EE 25128 ASSEMBLY AND OPERATING INSTRUCTIONS Visit our website at http Awww harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improve ments actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 Revised Manual 091 SPECIFICATIONS ITEM Construction Heavy Duty Formed amp Stamped Alloy Sheet Steel Black Pow der coated Finish amp Zinc Plated Fasteners Overall Dimensions 29 1 4 H x 30 1 2 L x 21 1 2 W Stand Top Dimensions 18 L x 9 3 4 W W Adjustable Slots to Extend Width Max Load Capacity 300 Lbs Net Weight 14 Lbs SAVE THIS MANUAL You will need the manual for the safety warnings and precautions assembly instructions operating and maintenance procedures parts list and diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep the manual and invoice in a safe and dr
5. LL SAW 16 SCROLL SAW 12 BAND SAW 13 SCROLL SAW Top Cross Brace 10 in holes marked W amp Z 2 holes 16 SCROLL SAW One Top Side 8 amp Top Front amp Rear Braces 9 amp 11 in holes marked D I amp T 3 holes 12 BAND SAW Top Front amp Rear Braces 9 amp 11 in holes marked J H R amp V 4 holes Figure 1 STEP 3 ie In some cases the Top Cross Brace 10 will change positions depending on the tool you are mounting Assemble according to the configuration of the drawing per taining the tool you are using See Figure 1 SKU 95128 For technical questions please call 1 800 444 3353 Page 5 CONFIGURATION FOR 4 BELT amp 6 DISC SANDER 15 SCROLL SAW 10 MITER SAW 8D46 SANDER Two Top Side Braces 8 in holes marked A D N amp Q 4 holes 8D46R SANDER One Top Side 8 Top Cross Brace 10 in holes marked N O W amp Z 4 holes 15 SCROLL SAW One Top Side 8 and Top Cross Braces 10 in holes marked O amp X 2 holes 10 MITER SAW Top Front amp Rear Braces 9 amp 11 in holes marked F L S amp V 4 holes Figure 2 STEP 3 1 In some cases the Top Cross Brace 10 will change positions depending on the tool you are mounting Assemble according to the configuration of the drawing per taining the tool you are using See Figure 2 SKU 95128 For technical questions please call 1 800 444 3353 Page 6 CONFIGURATION FOR 10 BAND SAW 10 BAN
6. Rear Bree Jo PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTA TION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTAL LATION OF REPLACEMENT PARTS THERETO SKU 95128 For technical questions please call 1 800 444 3353 Page 10 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal ac tivity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons
7. o perform a task for which it was not designed The correct equipment will do the job better and safer at the rate for which it is designed Do not use small equipment tools or attachments to do the work of larger industrial equipment tools or attachments Do not use this product for a purpose for which it was not intended 12 Use goggles or breathing protection not included for mouth and nose during all jobs that cause dust chips fumes or sparks 13 Protect your hearing when doing work causing a lot of noise Use ear plugs not included if necessary 14 Use HEAVY DUTY work gloves not included when working with tools and equipment 15 Never allow inexperienced personnel to work with your equipment and tools with out instructions and or supervision 16 Do not stand on top of the Heavy Duty Tool Stand 17 Do not exceed the Tool Stand s maximum weight capacity 300 Ibs 18 Do not let children stand on or play with the Heavy Duty Tool Stand 19 Always use the Tool Stand on a flat level surface that is able to withstand the weight of the Tool Stand and the weight of the objects on the Tool Stand 20 SAVE THESE INSTRUCTIONS WARNING The warnings cautions and instructions discussed in this instruction manual can not cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied b
8. y place for future reference gt A amp N 10 SAFETY WARNINGS AND PRECAUTIONS Keep work area clean Cluttered areas invite injuries Observe work area conditions Keep work area well lit Supervise children around this product Do not allow children in the work area Check for damaged parts Before using any product any part that appears dam aged should be carefully checked to determine that it will perform its intended function Check for any broken or damaged parts and any other conditions that may affect its operation Replace or repair damaged or worn parts immediately Use safety equipment Wear ANSIl approved safety impact eye goggles when assembling this product or when using machinery with this product Always check hardware and assembled parts after assembling All connections should be tight and hardware tightened Do not overreach Keep proper footing and balance at all times when assembling or using this product Stay Alert Watch what you are doing at all times Use common sense When using this product remember do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock When operating a power tool outside use an outdoor extension cord marked W A or W These extension cords are rated for outdoor use and reduce the risk of electric shock SKU 95128 For technical questions please call 1 800 444 3353 Page 2 11 Do not modify this tool t
9. y the operator WARNING Some dust created by power sanding sawing grinding drilling and other con struction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement or other masonry products Arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq SKU 95128 For technical questions please call 1 800 444 3353 Page 3 UNPACKING When unpacking this product check to make sure that all parts are included as shown in the parts list If any parts are missing or broken please call Harbor Freight Tools at the number below HARDWARE SPECIFICATION Hardware to mount power tools to the Heavy Duty Tool Stand are not supplied The recom mended minimum size of mounting hardware is listed below As a guide actual sizes may depend on tool base thickness Scroll Saw Miter Saw Drill Presses Band Saw Joiner Planer Sander Hex Head Bolts 1 4 20 x 1 2 4 5 16 1 8 x 2 1 2 Flat Washers 1 41 D 3 4 O D 5 16 D 7 8 O D Hex
Download Pdf Manuals
Related Search