Harbor Freight Tools 1.5 ton Scissor Jack Product manual
Contents
1. off the ground 7 Remove the lug nuts from the ve hicle s wheel Remove the wheel and replace it with the spare wheel not SKU 66907 o 11 12 For technical questions please call 1 800 444 3353 included Replace and tighten all the lug nuts onto the wheel Remove the old wheel tools and any other objects from under the vehicle Rotate the Handle 16 counterclock wise to lower the Jack Continue rotating the Handle until the Jack is completely collapsed to the ground Double check and re tighten the wheel lugs Remove the Jack Page 6 MAINTENANCE AND SERVICING Procedures not specifically A explained in this manual must be performed only by a qualified technician TO PREVENT AWARNING SERIOUS INJURY FROM TOOL FAILURE Do not use damaged equipment 1 BEFORE EACH USE inspect the general condition of the tool Check for loose hardware misalignment or binding of moving parts cracked or broken parts and any other condi tion that may affect its safe operation If anything is found do not use the Jack Have it repaired or replaced 2 AFTER USE wipe external surfaces of the tool with clean cloth 3 Keep the Scissor Jack clean and dry 4 Lubricate the threads of the Spindle Rod 6 of the Jack with high quality light weight oil not included Keep ing the Screw Rod well oiled and free of rust will avoid the jack binding dur ing use SKU 66907 For technical questions2. There are certain applications for which this Scissor Jack was designed It will do the job better and more safely at the rate for which it was intended Do not modify this Jack and do not use this Jack for a purpose for which it was not intended Maintain tools with care Keep tools clean for better and safer perfor mance Follow instructions for lubri cating and changing accessories Check for damaged parts Before using any tool any part that appears damaged should be carefully checked to determine that it will operate prop erly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other con dition that may affect proper opera tion Any part that is damaged should be properly repaired or replaced by a qualified technician If the Upper or Lower Forks are damaged they need to be replaced not repaired Replacement parts and accessories When servicing use only identical replacement parts Use of any other parts will void the warranty Only use accessories intended for use with this tool Approved accessories are avail able from Harbor Freight Tools 2f 28 20 30 For technical questions please call 1 800 444 3353 Stay alert Watch what you are do ing use common sense Do not oper ate any tool when you are tired Do not operate tool if under the influ ence of alcohol drugs or medica tion Read warning labels if taki
3. makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this prod uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESS LY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the com plaint must accompany the merchandise If our inspection verifies the defect we will ei ther repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return re paired products at our expense but if we determine there is no defect
4. please call 1 800 444 3353 Page 7 PARTS LIST amp DIAGRAM Part Description Qty 6 SpindeRod 1 8 UpperFork J 2 9 Jacking Head Seat SKU 66907 For technical questions please call 1 800 444 3353 Part Description Qty Under Fork Gear Page 8 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 66907 For technical questions please call 1 800 444 3353 Page 9 LIMITED 90 DAY WARRANTY Harbor Freight Tools Co
5. US GENERA 1 1 2 TON SCISSOR JACK VII l 1 66907 SET UP AND OPERATING INSTRUCTIONS Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2009 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Ney sof NOTICE is used to address practices Keep this manual for the safety warn not related to personal injury ings and precautions assembly operat ing inspection maintenance and cleaning CAUTION CAUTION without procedures Write the product s serial the safety alert number in the back of the manual near the symbol is used to address assembly diagram or month and year of practices not related to purchase if product has no number Keep personal injury this manual and the receipt in a safe and dry place for future reference General Saf
6. e Handle 16 COMPONENTS Figure 2 To assemble the Handle 16 and Rocker Bar 15 a Slide the hooked end of the Rocker Bar 15 into the holes in the Rocker Head 3 b Attach Handle 16 to the flat end of the Rocker Bar 15 Rocker Bar 15 Handle 16 Figure 1 SKU 66907 For technical questions please call 1 800 444 3353 Page 5 GENERAL OPERATING INSTRUCTIONS TO PREVENT AWARNING serious INJURY Park the vehicle on a flat level solid surface safely away from oncoming traffic Turn off the vehicle engine Place the transmission in Park if automatic or in reverse if manual Set the emergency brake 1 Assemble the Handle 16 and Rocker Bar 15 See Tool Set up for assembly 2 Ifthe Jack is not fully collapsed lower the Jack so that it will easily slide under the vehicle 3 Chock the wheels opposite the wheel to be removed 4 To make it easier to remove the wheel s lug nuts Slightly loosen the lug nuts prior to raising the wheel 5 Slide the Jack under the vehicle near the wheel being removed IMPORTANT The Scissor Jack is de signed for use on vehicle s with frame seams capable of sustaining rated capacity loads Carefully position the Scissor Jack under the vehicle manu facturer s recommended lift point 6 Rotate the Handle 16 clockwise raising the Jack Continue rotating the Handle until the vehicle is raised enough so the wheel is approximately 1
7. ety Warnings WARNING Read all safety IMPORTANT SAFETY warnings and instructions Failure to follow the warnings and IN FO RMATIO N instructions may result in serious injury In this manual on the labeling and all other information provid ed with this product Save all warnings and instructions for future reference m 1 Work area safety This is the safety alert symbol It is used to alert you to potential personal a Keep work area clean and well lit Cluttered or dark areas invite acci injury hazards Obey all dents safety messages that b Keep children and bystanders follow this symbol to avoid away while operating the Scissor possible injury or death Jack Distractions can cause you to lose control DANGER indicates 2 Personal safet A DANGER a hazardous d situation which if not a Stay alert watch what you are do avoided will result in death or ing and use common sense when serious injury operating the Scissor Jack Do not use while you are tired or un WARNING der the influence of drugs alcohol AWARNING indicates a or medication A moment of inat hazardous situation which if tention while operating the Scissor not avoided could result in Jack may result in serious personal death or serious injury injury CAUTION used b Do not overreach Keep proper A CAUTION with the safety footing and balance at all times alert symbol indicates a This enables better control of the hazardous situation whic
8. h if Scissor Jack in unexpected situa not avoided could result in tions minor or moderate injury SKU 66907 For technical questions please call 1 800 444 3353 Page 2 c Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts d Only use safety equipment that has been approved by an appro priate standards agency Unap proved safety equipment may not provide adequate protection Eye protection must be ANSI approved and breathing protection must be NIOSH approved for the specific hazards in the work area 3 Service a Have your Scissor Jack serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Scissor Jack Safety Warnings 1 Rated capacities 900 Ib extended 6 or more 1200 Ib extended 8 or more 1800 Ib extended 10 or more 3 000 Ib extended 14 or more 2 Study understand and follow all instructions before operating this device 3 Do not exceed rated capacities AT SPECIFIED HEIGHTS 4 Do not use if Jack cannot extend at least 6 before lifting the load 5 Do not use blocks underneath or above Jack 6 Use only on hard level surface SKU 66907 14 15 1f For technical questions please call 1 800 444 3353 Use only for emergency tire chang ing or mou
9. ng prescription medicine to determine if your judgment or reflexes are im paired while taking drugs If there is any doubt do not operate the tool Maintain labels and nameplates on the tool These carry important safety information If unreadable or miss ing contact Harbor Freight Tools for a replacement The warnings precautions and in structions discussed in this instruction manual cannot cover all possible con ditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS Page 4 SPECIFICATIONS OPERATING INSTRUCTIONS 3000 Ib extended 14 or more Read the ENTIRE IMPORTANT 1800 Ib extended 10 or more SAFETY INFORMATION Jack Capacity 1200 Ib extended 8 or more section at the beginning of this 900 Ib extended 6 or more manual including all text under LEuheinge 9030 Tos subheadings therein before set E 000 up or use of this product c 3 3000 e 2500 Tool Set Up gt 2000 1800 S 1500 1200 Jack Rocker Head 3 amp 1000 9200 500 D z 6 8 10 12 14 Height in inches UNPACKING Rocker Bar 15 When unpacking make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at 1 800 444 3353 as soon as possibl
10. nting tire chains Never get beneath the vehicle when it is supported by the Jack If vehicle is pushed off Jack dis card Jack Do not reuse Wear ANSI approved safety gog gles and heavy duty work gloves during use Keep clear of load while lifting and lowering Do not use for aircraft purposes Apply parking brake and chock tires before lifting vehicle Lift vehicle only at manufacturer s recommended locations Inspect before use do not use if parts are loose or damaged Activate the hazard warning flasher turn off ignition set parking brake move automatic shift selector to park position before attempting to jack up car In case of manual transmission move gear selector into reverse posi tion In addition the wheel diagonally opposite from the wheel being lifted shall be chocked in both directions Follow tire changing procedure or tire chain mounting procedure specified in the vehicle manufacturer s owner s manual No alterations shall be made to this product Never stand on the Jack and never have people or pets in the vehicle you are attempting to raise Page 3 20 21 22 29 24 25 26 SKU 66907 Only lift the vehicle until one wheel is off the ground Keep hands and fingers away from joints or jack interior Keep children away Children must never be allowed in the Scissor Jack area Do not let them handle the Jack at any time Use the right tool for the job
11. or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 SKU 66907 For technical questions please call 1 800 444 3353 Page 10
Download Pdf Manuals
Related Search