Home
GE SnapDrive Installation Guide
Contents
1. 8 inch O D or 2 7 8 O D through 3 inch O D pipes Set screws are used to clamp the floodlight securely to the pipe Tighten set screws to 10 foot pounds 13 6 Nem Slipfitter is designed to mount on a vertical pipe pointed upward such that gravity acts to hold floodlight in place while the set screws are tightened Do not mount unit up side down Figure 1 i Set Screws h Wall Mounted units The wall mounting plate is provided with four 438 inch clearance holes spaced 4 375 H x 2 875 V inches for mounting Do not mount the unit such that the hinge side of door is higher than the latch side of door UH 4 375 in 111mm 2 875 in 73mm 4 holes 438 in These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes the matter should be referred to GE Lighting Solutions WIRING Make all electrical connections in accordance with all applicable code requirements National Electrical Code Canadian Electrical Code and applicable local codes This luminaire is equipped with a SnapDrive electrical system The SnapDrive is equi
2. GE Lighting Solutions A WARNING Risk of electric shock e Turn power off before servicing see instructions A WARNING Risk of fire e Use supply wire specified on nameplate GENERAL This luminaire is designed for outdoor lighting applications and should not be used in areas of limited ventilation or in high ambient temperature enclosures Best results will be obtained if installed and maintained according to the following recommendations WARNING PAINFUL BURNS OF THE SKIN CAN RESULT FROM TOUCHING OR HANDLING THE FLOODLIGHT WHILE OPERATING The floodlight should not be installed in reach of the general public unless it is protected from accidental handling as the outside temperature of the housing and particularly the glass can be sufficiently high to cause burns of the skin Floodlight should also be ordered with a door that is screwed shut if the latches are in reach of the general public Criterion floodlights have both a screw closure option andtamper resistant screw option UNPACKING This luminaire has been properly packed so that no parts should have been damaged during transit Inspect to confirm MOUNTING A CAUTION Unit will fall if not installed properly e Follow installation instructions GEH 5805A INSTRUCTIONS Criterion Floodlight 100 175 Watt Followinstallation instructions 1 Figure 2 Pipe Mounted units The slipfitter can be mounted on 1 7 8 inch O D though 2 3
3. TALLATION A CAUTION Risk of burn e Allow lamp fixture to cool before handling A WARNING Risk of burn e Do not touch operating luminaire Use only lamps specified on nameplate Observe lamp manufacturer s recommendations and restrictions on lamp operation particularly ballast type burning position etc Lamp Tightness Medium Base Lamp The lamp should be tightened to a light firmness sufficient to depress the center contact MAINTENANCE AND CLEANING It will occasionally be necessary to clean the outside of the door glass to maintain light levels Frequency of cleaning will depend on ambient dirt level and minimum light level that is acceptable to the user The door glass Should be washed in a solution of warm water and any mild nonabrasive household detergent rinsed with clean water and wiped dry Should the optical assembly become dirty on the inside wipe the reflector and clean the refractor in the above manner The light output of a luminaire is dependent on the age of the lamp In applications where the light level is critical it may be desirable to replace lamps before they burn out The lamp manufacturer can provide data showing how the lamp light output decreases with use GE Lighting Solutions e 1 888 MY GE LED e www gelightingsolutions com 1 888 69 43 533 GE Lighting Solutions is a subsidiary of the General Electric Company Evolve and other trademarks belong to GE Lighting Solutions The GE brand and logo
4. are trademarks of the General Electric Company 2011 GE Lighting Solutions Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions 35 201578 6C 7 01
5. pped with a multi volt ballast Ballast has been wired to the voltage indicated on the nameplate If another voltage is desired place the voltage selection jumper onto the appropriate voltage position as indicated on the wiring diagram on the Snapdrive ballast cover Optional features such as fusing and photocontrols are voltage specific Do not change jumper positions if fixture is equipped with these features This will damage or destroy these optional parts and will void the applicable safety listing UL CUL CSA etc of the fixture SNAPDRIVE REMOVAL AND INSTALLATION To remove Snapdrive with the power off open door by releasing the two top latches Disconnect all wire harnesses from SnapDrive Press clip located at bottom end of module see figure 3 Swing Snapdrive forward and lift off the hooks located at top end Snap Drive See figure 4 To install Snapdrive with power off open door of unit Hang module on hooks figure 3 Swing Snapdrive into clip lifting slightly as Snapdrive is swung into place An audible snap should be heard which indicates the module has seated Replace wiring harnesses into proper receptacles Hooks SnapDrive Electrical System Clip Figure 3 Figure 4 LAMP INS
Download Pdf Manuals
Related Search
Related Contents
取扱説明書 Samsung RH77H90507H FSR with Foodshowcase, 765 L User Manual PWS 550 PWS 600 PWS 6-115 PWS 7-100 PWS 7-115 PWS 7 New Media Technology Omnia ONE Multicast User's Manual EF40i Operation Manual LA N.ÜthELLE TRICHE EST ARRIVEE. DANS LES NEC AS231WM Miele KFNS 37692 iDE Operating and Installation Instructions Philips SBCHC210 JVC TU-DB1SK User's Manual Copyright © All rights reserved.
Failed to retrieve file