GE RI Series Installation Guide
Contents
1. 1 Shut off power to the lighting system f O N RA i eka ei r 4 Loop one end of the tether to existing rough in kit 3 Disconnect wiring Remove old components such as lamp sockets ballasts etc while retaining existing rough in kit components 2 Remove existing lamp and reflector TY LE LSN D ow p M ra i XN I L ES I Q Connect the black white and green wires of the AC line to the black white and green wires of the fixture using twist on wire connectors Close junction box Attach other end of the tether to fixture housing and let hang QO Connect flex cable from fixture to junction box NOTE See wiring diagram below if connecting an optional dimming line J box is vertical JE L brackets PN over notches O Orient J box vertically and slide Slide the L brackets to the top of 10 Snap in reflector fixture housing without reflector into existing rough in kit Then rotate J box horizontally 1 1 Restore power to the lighting system each leg and ensure the bracket slot channel is engaged by pushing the bracket through the notches Slide each bracket down to engage existing rough in kit and tighten thumb screws Optional Installation 0 10 Volt Dimming Lighting Controller At output side of LED driver make appropriate connections using twist on wire connectors Follow lighting controller installation instructions Line black2. Line Neutral white Neutral DRIVER Ground green Ground 0 10V violet 0 10V 0 10V gray 0 10V 0 10V wiring diagram This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class A RFLD complies with the Canadian standard ICES 003 Ce DEFR de la classe A est conforme la NMB 003 du Canada Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense GE Lighting 1 888 MY GE LED 1 888 69 43 533 www gelighting com GE Lighting Solutions LLC is a subsidiary of the General Electric Company The GE brand logo and Lumination are trademarks of the General Electric Company 2015 GE Lighting Sol
3. Fixture Requirements e Per the NEC this fixture is non plenum rated for use in ducts specifically fabricated for environmental air It is suitable for use above the ceiling in open spaces used for environmental air e 35 C maximum cavity temperature during lamp operation e Thermal protection feature present in module that protects LEDs from overheating in abnormal conditions Grounding Instructions The grounding and bonding of the overall system shall be done in accordance with National Electric Code NEC Article 600 and local codes e Spacing requirements for fixture each individual fixture needs to have 576 square inches of space before any object obstruction a 36 inches m NI Parameter A Width of Frame with Swing Arm Extended Height from Bottom of Reflector to Top of B Heat Sink c Height from Bottom of Reflector to Top of Frame D Reflector Diameter E Cut Out Dimension for Ceiling F Maximum Ceiling and Rough in Kit Thickness 6 10 34 5 92 Low Lumen 3 91 7 40 6 45 7 125 7 125 7 88 w Goof Ring 1 625 Frame Size g 12 51 8 37 High Lumen 7 39 Low Lumen 5 57 8 80 7 88 8 50 8 5 9 75 w Goof Ring 3 00 S YDU 9T 10 13 55 9 32 High Lumen 8 34 Low Lumen 6 52 10 80 9 75 10 50 10 50 12 50 w Goof Ring 4 25 Installation
4. GE Installation Guide Lighting Lumination LED Luminaire RI Series BEFORE YOU BEGIN Read these instructions completely and carefully WARNING AVERTISSEMENT RISK OF FIRE OR ELECTRIC SHOCK RISQUES D INCENDIE OU DE DECHARGES LECTRIQUES e Turn power off before inspection installation or removal e Coupez l alimentation avant d inspecter installer ou d placer le luminaire Properly ground electrical enclosure e Assurez vous de correctement mettre la terre le bo tier d alimentation lectrique Respectez tous les codes NEC et codes locaux utilisez que des fils approuv s par UL pour les entr es sorties de te one connexion Taille minimum 18 AWG ou 14 AWG pour les rang es continues Install this kit only in the luminaires that has the construction Ri di di hoc Li ks k sques d incendie ou choc L installation de trousses de mise niveau au DEL features and dimensions shown in the photographs and or drawings n cessite des connaissances des syst mes lectriques d clairage Do not alter relocate or RS NES lampholders power Risque d incendie ou d lectrocution N installer cette trousse que sur des supply or another electrical component luminaires qui ont les caract ristiques de construction et les dimensions nstallation of this retrofit assembly requires a person familiar with telles que montr es sur les photographies et dessins pr sent s the construction and operation of the luminaire s elect
5. rical system e pas percer ou alt rer les trous d un boitier contenant fil ou composant and the hazard involved If not qualified do not attempt lectrique durant installation Follow all NEC and local codes Use only UL approved wire for input output connections inimum size 18 AWG or 14 AWG for continuous runs installation Contact a qualified electrician 7 Pour pr venir les dommages ou l abrasion de fils lectriques ne pas exposer e To prevent wiring damage or abrasion do not expose wiring to les fils aux ar tes de pi ce de t lerie ou n importe quels autres objets edges of sheet metal or other sharp objects tranchant Save These Instructions Use only in the manner intended by the manufacturer If you have any questions contact the manufacturer The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by CSA or authorities having jurisdiction Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation Through Wiring for 15A Circuit Lumen Level Maximum number of fixtures 1000 1500 2000 lumen 30 3000 4000 lumen 20 imagination at work Prepare Electrical Requirements The LED driver must be supplied with 120 277 VAC 50 60 Hz and connected to an individual properly Electrical Wiring grounded branch circuit protected by a 20 ampere circuit breaker Use min 75 C supply conductor
6. utions LLC Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions INDO98 011315
Download Pdf Manuals
Related Search