Home

Garmin 2006T Cockpit Reference Guide

Contents

1. euonippv uoneiedo Jeuuouqv ji x pul Hazard Flight Nav Com Fight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix Annunciations amp Alerts TERRAIN SVS ALERTS A GARMIN PFD MFD Alert Type TERRAIN SVS MFD Aural yp Page Pop Up Alert Message Annunciation Reduced Required Terrain TERRAIN Warning Terrain Clearance Warning RTC Terrain Imminent Terrain Impact TERRAIN Warning Terrain Warning ITI Terrain Reduced Required Obstacle TERRAIN Warning Obstacle Clearance Warning ROC Obstacle Imminent Obstacle Impact TERRAIN Warning Obstacle Warning 101 Obstacle Reduced Required Terrain TERRAIN CAUTION TERRAIN Caution Terrain Clearance Caution RTC Terrain Imminent Terrain Impact TERRAIN 1 CAUTION TERRAN Caution Terrain Caution ITI Terrain Reduced Required Obstacle TERRATN 1 CAUTION OBSTACLE Caution Obstacle Clearance Caution ROC Obstacle Imminent Obstacle Impact TERRAIN 1 caurton oBSTACLE Caution Obstacle Caution 101 Obstacle TERRAIN SVS SYSTEM STATUS ANNUNCIATIONS Alert Type System Test fail Terrain Alerting is disabled TER INH No GPS position or excessively degraded GPS signal System Test in progress System Test pass 66 Garmin G950 Coc
2. GRS 77 Message 501165 GMU 44 Message Advisories GDC 74A Message Advisories GDL 69 Message Advisories Miscellaneous Message Advisories ssssssss Flight Plan Import Export Messages ssssnnn 83 APPENDIX cc esi eat thi lle PFD Softkey Map MFD Softkey Map Loading Updated Databases 91 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T Table of Contents GARMI N Blank Page Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Flight instruments FLIGHT INSTRUMENTS SELECTING THE ALTIMETER BAROMETRIC PRESSURE SETTING mal ca g 2 o a 59 Tum the BARO to select the desired setting SELECTING STANDARD BAROMETRIC PRESSURE 29 92 IN HG olpny uqax U105 AEN 1 Press the PFD Softkey 2 Press the STD BARO Softkey to set standard barometric pressure 52 CHANGE ALTIMETER BAROMETRIC PRESSURE SETTING UNITS 1 Press the PFD Softkey to display the second level softkeys 2 Press the ALT UNIT Softkey 3 Press the IN Softkey to display the barometric pressure setting in inches of mercury in Hg Or Press the HPA Softkey to display the barometric pressure setting in hectopascals 4 Press the BACK Softkey to ret
3. PFD1 COOLING PFD1 has poor MFD1 COOLING MFD1 has poor cooling Reducing power usage cooling Reducing power usage The PFD and or MFD is overheating and is reducing power consumption by dimming the display If problem persists the G950 system should be serviced PFD1 KEYSTK PFD1 key name Key is stuck MFD1 KEYSTK MFD key name Key is stuck A key is stuck on the PFD and or MFD bezel Attempt to free the stuck key by pressing it several times The G950 system should be serviced if the problem persists CNFG MODULE PFD1 configuration module is inoperative The PFD1 configuration module backup memory has failed The G950 system should be serviced PFD1 VOLTAGE PFD1 has low voltage Reducing power usage The PFD1 voltage is low The G950 system should be serviced MFD1 VOLTAGE MFD1 has low voltage Reducing power usage The MFD voltage is low The G950 system should be serviced DATABASE MESSAGE ADVISORIES Message Comments MFD1 DB ERR MFD1 navigation database error exists PFD1 DB ERR PFD1 navigation database error exists The MFD and or PFD detected a failure in the navigation database Attempt to reload the navigation database If problem persists the G950 system should be serviced MFD1 DB ERR MFD1 basemap database error exists database error exists PFD1 DB ERR PFD1 basemap The M
4. 4 aoueplony puezey s l Jeuonippy uoneiedo jeuuouqy suay junuuy xipuaddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 60 GARMI N Abnormal Operation ABNORMAL OPERATION REVERSIONARY MODE Should a system detected failure occur in either display the G950 automatically enters reversionary mode In reversionary mode critical flight instrumentation is combined with engine instrumentation on the remaining display Reversionary display mode can be manually activated by pressing the display backup button installed in the cockpit NOTE The Pilot s Operating Handbook POH and or Airplane Flight Manual AFM always takes precedence over the information found in this section ABNORMAL COM OPERATION When a COM tuning failure is detected by the system the emergency frequency 121 500 MHz is automatically loaded into the active frequency field of the COM radio for which the tuning failure was detected In the event of a failure of both PFDs the emergency frequency 121 500 MHz automatically becomes the active frequency on both COM radios HAZARD DISPLAYS WITH LOSS OF GPS POSITION If GPS position is lost or becomes invalid selected hazards being displayed on the Navigation Map Page are removed until GPS position is again established Loss of Hazard Functions with Loss of GPS Position 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the
5. 4 Select any one of the PS1 PS15 softkeys to assign a number to the active channel Adjusting Volume 1 With the XM Radio Page displayed select the VOL Softkey 2 Select the VOL Softkey to reduce volume or select the VOL Softkey to increase volume Once the VOL Softkey is selected the volume can also be adjusted using the small FMS Knob 3 Select the MUTE Softkey to mute the audio Select the MUTE Softkey again to unmute the audio 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 37 2 Buruuejd AeN Sd5 S24V olpnyyuqax sia syuawin jsu Tu102 AEN UTE aoueplony paezey xipuaddy SH V uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy x pul Flight Instruments Nav Com XPDR Audio Flight Planning Hazard Avoidance Additional Features Abnormal Annun EIS AFCS GPS Nav Procedures Appendix Alerts Operation Index A Additional Features GARMIN ELECTRONIC CHECKLISTS IF INSTALLED The system accesses the checklists from an SD card inserted into the bezel slot If the SD card contains an invalid checklist file or no checklist the Power up Page messages display Checklist File Invalid or Checklist File N A not available and the CHKLIST Soltkey is not available Accessing and Navigating Checklists 1 2 3 4 5 6 1 8 9 10 58 From any page on the MFD press the CHKLIST Softkey Turn the l
6. A WARNING Do not use SVS runway depiction as the sole means for determining the proximity of the aircraft to the runway or for maintaining the proper approach path angle during landing Synthetic Vision System SVS functionality is offered as an optional enhancement to the G950 Integrated Flight Deck System SVS is primarily comprised of a computer generated forward looking attitude aligned view of the topography immediately in front of the aircraft from the pilots perspective SVS information is shown on the primary flight display PFD In addition to SVS enhancement to the PFD the following features have been added to the PFD e Pathways e Flight Path Marker e Horizon Heading Marks e Terrain and Obstacle Alerting Three dimensional Traffic Airport Signs e Runway Display Displaying SVS Terrain 1 Press the PFD Softkey 2 Press the SYN VIS Softkey 3 Press the SYN TERR Softkey 4 Press the BACK Softkey to return to the previous page 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 49 xipuaddy SH V uoneiedo sainjea4 aoueplony SoJnpa204d Duruue d AEN Sd5 S24JV olpny uqax 413 siu un sul junuuy Jeuuouqy Jeuonippy p EzeH 34 wo gt AeN ubiu x pul Flight Instruments Nav Com XPDR Audio Flight Planning Hazard Avoidance Additional Features Abnormal Annun EIS AFCS GPS Nav Procedures Appendix Alerts Operation Index A Ad
7. Appendix Alerts Operation Features Avoidance Index A Procedures GARMIN LOAD AN ARRIVAL PROCEDURE 1 2 3 4 5 6 1 8 9 10 11 12 Press the PROC Key Turn the large FMS Knob to highlight SELECT ARRIVAL Press the ENT Key The cursor is displayed in the ARRIVAL field with a list of available arrivals Turn the large FMS Knob to highlight the desired arrival Press the ENT Key A list of transitions is displayed for the selected arrival Turn either FMS Knob to select the desired transition Press the ENT Key A list of runways may be displayed for the selected arrival Turn the large FMS Knob to highlight the desired runway Press the ENT Key With LOAD highlighted press the ENT Key The arrival becomes part of the active flight plan If an altitude associated with a waypoint in an arrival procedure is to be used to calculate vertical guidance perform the following steps a Press the FMS Knob to activate the cursor b Turn the large FMS Knob to highlight the desired waypoint altitude Press the ENT Key to designate the altitude for use in giving vertical guidance ACTIVATE AN ARRIVAL LEG Activate Arrival using the Quick Select Box 36 1 2 3 4 Press the FPL Key on the MFD to display the active flight plan Use the Joystick to move the Quick Select Box to the TO waypoint of the desired leg within the arrival Press the ACT LEG Softkey A confirmation wind
8. Categories list Highlight the desired category with the small FMS Knob Press the ENT Key Select an Available Channel within the Selected Category 1 2 3 While on the XM Radio Page select the CHNL Softkey Select the CH Softkey to go down through the list in the Channel Box or move up the list with the CH Softkey Or Press the FMS Knob to highlight the channel list and turn the large FMS Knob to scroll through the channels With the desired channel highlighted press the ENT Key Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Additional Features Entering a Channel Directly 1 While on the XM Radio Page select the CHNL Softkey 2 Select the DIR CH Softkey The channel number in the Active Channel Box is highlighted 3 Select the numbered softkeys located on the bottom of the display to directly select the desired channel number 4 Press the ENT Key to activate the selected channel Assigning Channel Presets Up to 15 channels from any category can be assigned a preset number 1 On the XM Radio Page with the desired channel active select the PRESETS Softkey to access the first five preset channels PS1 PS5 2 Select the MORE Softkey to access the next five channels PS6 PS10 and again to access the last five channels PS11 PS15 Selecting the MORE Softkey repeatedly cycles through the preset channels 3 Select the SET Softkey
9. Taipei County Taiwan Fax 886 02 2642 9099 of this man red in any st ts subsidiaries Garmin WATCHS a its subsidiaries Th n Inc related organizations hereina espect to the AOPA informati ed to the implied warranties ual and of any revision to this manual onto a ha iewed for personal use provided that on must contain the complete text of this copyright distribution of th on of eflects the operation of System Software version 0935 12 or later for the Tecnam me differences in operation may be observed when comparing the information in national Inc 1200 East 151st Street Olathe Kansas 66062 U S A Europe Ltd Liberty House Bulls Copse Road Hounsdown Business Park r after hours emergency aircraft on ground AOG technical support for Garmin panel mount egrated avionics systems please contact Garmin s AOG Hotline at 913 397 0836 ual may be reproduced copied orage medium for an of Garmin Garmin hereby grants permission to y purpose rd drive or such electronic is manual or any nd SafeTaxi are ese trademarks may not be used ter collectively included in this merchantability and fitness for a particular purpose The information is provided as is and AOPA does not warrant or make any representations regardin no circumstances including negligence sha g its accuracy reliability or otherwise Under AOPA be liable for any incidental special o
10. Terrain and obstacles may be displayed in the Profile View by selecting the PROFILE Softkey 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 4 AEN 640 S24V oipny uadx sia siu umninsul Tuo2 AEN iui Duruue d nubi aoueploay s mp oold paezey Suelv uoneiedo sainjea4 Tunuuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Abnormal Additional Annun Flight Instruments Flight Planning EIS AFCS GPS Nav Hazard Avoidance Procedures Appendix Alerts Operation Features Index A Hazard Avoidance GARMIN TERRAIN AWARENESS amp WARNING SYSTEM TAWS B DISPLAY IF INSTALLED WARNING The TAWS display shows supplemental information only It should not be used for navigation NOTE Terrain data is not displayed when the aircraft is outside the installed terrain database coverage area NOTE TAWS operation is only available when the G950 system is configured for a TAWS B installation Manual System Test 1 2 3 While the TAWS B Page is displayed press the MENU Key Turn the small FMS Knob to select Test TAWS System Press the ENT Key During the test TAWS TEST is displayed in the center of the TAWS B Page When all is in working order a single aural chime is heard Display Terrain on the TAWS B Page 1 2 3 4 46 Turn the large FMS Knob to select the Map Page Group Turn the small FMS Knob to select the TAWS B
11. blue text Altitudes associated with arrival procedures are manually designated This means the system does not use the altitudes loaded with the arrival for giving vertical flight path guidance until designated to do so by the pilot Note that these altitudes are initially displayed as white text These altitudes may be designated by placing the cursor over the desired altitude and pressing the ENT Key After designation the text changes to light blue 16 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Altitudes that have been designated for use in vertical navigation may also be made non designated by placing the cursor over the desired altitude and pressing the CLR GPS Navigation Key The altitude is now displayed only as a reference t is not used to give vertical flight path guidance Other displayed altitudes may change due to re calculations or rendered invalid as a result of manually changing an altitude to a non designated altitude White Text Light Blue Text Light Blue Subdued Text Large Text Altitude calculated by the Altitude has been entered The system cannot System estimating the by the pilot Altitude is use this altitude in altitude of the aircraft as it designated for use in determining vertical passes over the navigation giving vertical flight path flight path guidance point This altitude is guidance Altitude does provided as a re
12. ssssssseseeeen nnne 3 Activate a Stored Flight Plan 4 Activate a Flight Plan Leg 4 Stop Navigating a Flight Plan 5 Vertical Navigation VNAV ll s s s s ntn 6 FLIGHT PLANNING cies a A a 9 Trip Plannihjg eiie e e e ie ei ee deed 9 Create a User Waypoint Defined by Latitude amp Longitude 21 Create a User Waypoint Defined by Radials from Other Waypoints 21 Create a User Waypoint Defined by a Radial amp Distance from Another Waypoint 23 Create a User Waypoint using the Map Pointer 25 Delete a User Waypoint sssssssseeeennn nnne 25 Create a Flight Pl n cnr tane ante edendo 26 Import a Flight Plan from an SD Card 2 Insert a Waypoint in the Active Flight Plan 2 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T Table of Contents GARMI N Enter an Airway in a Flight Plan 28 Invert An Active Flight Plan 29 Remove a Departure Arrival Approach or Airway from a Flight Plan 29 Store a Flight Plan 30 Edit a Stored Flight Plan 665 30 Delete a Waypoint from the Flight Plan sss 30 Invert and Activate a Stored Flight 5 31 Copy a
13. 3 Press the NEW Softkey A waypoint is created at the current aircraft position 4 Enterthe desired waypoint name 5 Press the ENT Key 6 The cursor is now in the WAYPOINT TYPE field If desired the waypoint can be made temporary deleted automatically when the system is turned off If the waypoint is to remain in the system proceed to step 7 a Turn the large FMS Knob one click to the left to highlight TEMPORARY b Press the ENT Key to place a check mark in the box Turn the large FMS Knob to place the cursor back in the WAYPOINT TYPE field 7 With the cursor in the WAYPOINT TYPE field turn the small FMS Knob to display a list of waypoint types 8 Turn the small FMS Knob to select LAT LON latitude and longitude 9 Press the ENT Key 2 AEN 540 nubi CREATE A USER WAYPOINT DEFINED BY RADIALS FROM OTHER WAYPOINTS 1 Turn the large FMS Knob on the MFD to select the WPT page group 2 Turn the small FMS Knob to select the User WPT Information Page 3 Press the NEW Softkey A waypoint is created at the current aircraft position 4 Enterthe desired waypoint name 5 Press the ENT Key 6 The cursor is now in the WAYPOINT TYPE field If desired the waypoint can be made temporary deleted automatically when the system is turned off If the waypoint is to remain in the system proceed to step 7 a Turn the large FMS Knob one click to the lef
14. AUTOMATIC page mode fuel flow is provided by the system The flashing cursor moves to the fuel onboard field Enter the fuel onboard Press the ENT Key when finished Note that in AUTOMATIC page mode fuel onboard is provided by the fuel totalizer The flashing cursor moves to the calibrated airspeed CALIBRATED AS field Enter the calibrated airspeed Press the ENT Key when finished Note that in AUTOMATIC page mode calibrated airspeed is provided by the system The flashing cursor moves to the altitude IND ALTITUDE field Enter the altitude Press the ENT Key when finished Note that in AUTOMATIC page mode altitude is provided by the system The flashing cursor moves to the barometric setting PRESSURE field Enter the desired baro setting Press the ENT Key when finished Note that in AUTOMATIC page mode the baro setting is provided by the setting entered on the PFD The flashing cursor moves to the air temperature TOTAL AIR TEMP field Enter the desired air temperature Press the ENT Key when finished Note that in AUTOMATIC page mode air temperature is provided by the system outside air temperature Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Flight Planning CREATE A USER WAYPOINT DEFINED BY LATITUDE amp LONGITUDE 1 Turn the large FMS Knob on the MFD to select the WPT page group 2 Turn the small FMS Knob to select the User WPT Information Page
15. Knob to select UP or DOWN then press the ENT Key START is now highlighted Press the ENT Key to START STOP or RESET the timer if the timer is counting DOWN it starts counting UP after reaching zero Press the CLR Key or the TMR REF Softkey to remove the window SET BAROMETRIC MINIMUM DESCENT ALTITUDE 1 2 3 4 5 6 7 Press the TMR REF Softkey Turn the large FMS Knob to highlight the OFF BARO field to the right of MINIMUMS Turn the small FMS Knob clockwise to BARO Press the ENT Key Use the small FMS Knob to enter the desired altitude Press the ENT Key To remove the window press the CLR Key or the TMR REF Softkey Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Pightinstruments DISPLAYING WIND DATA ze ca g 2 o a 1 Press the PFD Softkey 2 Press the WIND Softkey to display wind data to the left of the HSI 3 Press one of the OPTN softkeys to change how wind data is displayed 4 To remove the Wind Data Window press the OFF Softkey CHANGING HSI FORMAT olpny uqax U105 AEN 1 Press the PFD Softkey 2 Press the HSI FRMT Softkey 3 Press the 360 HSI Softkey to display the full size HSI Or Press the ARC HSI Softkey to display the arc style HSI sualy uonesado so1njeoJ uepjoay seinpa2oJd Buruuejg AEN 5649 24V junuuy jeuuouqy paezey nubi xipuaddy x p
16. Knob to the right to display the NRST airports to the aircraft s current position Turn the large FMS Knob to select the desired waypoint Press the ENT Key Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed Turn the small FMS Knob to the right to display the RECENT waypoints Turn the large FMS Knob to select the desired waypoint Press the ENT Key Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed Turn the small FMS Knob to the right to display the USER waypoints Turn the large FMS Knob to select the desired waypoint Press the ENT Key Press the ENT Key The cursor is displayed in the RAD radial field Enter the desired radial from the reference waypoint Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Flight Planning 12 Press the ENT Key 13 Repeat step 10 to enter the next waypoint name 14 Press the ENT Key The cursor is displayed in the RAD radial field for the second vvaypoint Enter the desired radial from the reference vvaypoint 15 Press the ENT Key 16 Press the FMS Knob to remove the flashing cursor CREATE A USER WAYPOINT DEFINED BY A RADIAL amp DISTANCE FROM ANOTHER WAYPOINT sjuauimasu sub oipny uddx 93 UI0JNeN 52 1 Tum the large FMS Knob on the MFD to select the WPT page group 2 Turn the small FMS Knob to select the User
17. Page If desired press the VIEW Softkey to access the ARC and 360 softkeys When the ARC Softkey is selected a radar like 120 view is displayed Press the 360 Softkey to return to the 360 default display Rotate the Joystick clockwise to display a larger area or rotate counter clockwise to display a smaller area Terrain Obstacle Location Terrain Obstade above or within 100 below current aircraft altitude Terrain Obstacle between 100 and 1000 below current aircraft altitude Terrain Obstade is more than 1000 Black below aircraft altitude Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Hazard avoidance Enable Disable Aviation Data 1 While the TAWS B Page is displayed press the MENU Key 2 Turn the small FMS Knob to select Show or Hide Aviation Data 3 Press the ENT Key TAWS Inhibit NOTE If TAWS alerts are inhibited when the Final Approach Fix is the active waypoint in a GPS SBAS approach a LOW ALT annunciation may appear on the PFD next to the altimeter if the current aircraft altitude is at least 164 feet below the prescribed altitude at the Final Approach Fix Inhibit TAWS While the TAWS B Page is displayed press the INHIBIT Softkey Or 1 Press the MENU Key 2 Tum the small FMS Knob to select Inhibit TAWS 3 Press the ENT Key Enable TAWS While the TAWS B Page is displayed press the INHIBIT Softkey Or 1 While the TAWS B P
18. SD card contains user waypoints The quantity of stored user waypoints has exceeded system capacity therefore not all the user waypoints on the SD card have been imported Any flight plan user waypoints that were not imported are locked in the flight plan The flight plan must be edited within the system before it can be activated for use One or more user waypoints renamed One or more imported user waypoints were renamed when imported due to naming conflicts with waypoints already existing in the system Flight plan successfully exported The stored flight plan was successfully exported to the SD card Flight plan export failed The stored flight plan was not successfully exported to the SD card The SD card may not have sufficient available memory or the card may have been removed prematurely 84 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A dh GARMIN Appendix APPENDIX sjuauimasu Yid PFD SOFTKEY MAP if installed mer L 1 ES we GE eT eT ET nna r 7 75 75 ui 59 CDI NAV1 CD NAV2 olpny uqax uo2 AEN Top Level PFD Softkeys 2 if installed 2 lt S D v Dn n p amp 77 D D D Q if installed if installed if installed if installed oro rese Ee fu verir aac AERTS LA EF FV F amp rn n n n n Qa S Press the BACK Softkey to
19. Softkey Press the TERRAIN Softkey Terrain and obstacle proximity will now be displayed on the map 43 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T AEN Sd5 52 oipny uddx sia 0105 AEN Duruue d nubi s mp oold paezey Sue v uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Hazard Avoidance Procedures Abnormal Additional Annun Flight Instruments Flight Planning AFCS GPS Nav Appendix Alerts Operation Features Index A Hazard Avoidance GARMIN TERRAIN SVS IF INSTALLED A NOTE Terrain SVS is only available when the Synthetic Vision System SVS option is installed and the TAWS B option has not been installed NOTE Terrain data is not displayed vvhen the aircraft is outside the installed terrain database coverage area Display Terrain on the TERRAIN SVS Page 1 Tum the large FMS Knob to select the Map Page Group 2 Turn the small FMS Knob to select the Terrain SVS Page 3 If desired press the VIEW Softkey to access the ARC and 360 softkeys When the ARC Softkey is selected a radar like 120 view is displayed Press the 360 Softkey to return to the 360 default display 4 Rotate the Joystick clockwise to display a larger area or rotate counter clockwise to display a smaller area Terrain Obstacle Location Terrain Obstacle above or within 100 below current aircraft alt
20. THE FLIGHT PLAN Delete using the Quick Select Box active flight plan only 30 1 2 3 4 Press the FPL Key on the MFD to display the active flight plan Use the Joystick to move the Quick Select Box around the desired waypoint to be deleted Press the CLR Key to display a confirmation window With OK highlighted press the ENT Key to remove the selected waypoint Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Flight Planning Delete using the cursor 1 Press the FPL Key to display the active flight plan Press the FMS Knob to activate the cursor Or for a stored flight plan a Press the FPL Key on the MFD b Turn the small FMS Knob to select the Flight Plan Catalog Page Press the FMS Knob to activate the cursor d Turn the large FMS Knob to highlight the desired flight plan e Press the EDIT Softkey 2 Tum the large FMS Knob to highlight the waypoint to be deleted 3 Press the CLR Key to display a REMOVE Wpt Name confirmation window 4 With OK highlighted press the ENT Key to remove the waypoint To cancel the delete request turn the large FMS Knob to highlight CANCEL and press the ENT Key 5 Once all changes have been made press the FMS Knob to remove the cursor INVERT AND ACTIVATE A STORED FLIGHT PLAN 1 Press the FPL Key on the MFD 2 Turn the small FMS Knob to select the Flight Plan Catalog Page 3 Pre
21. however other had errors and were not imported A parti stored flight plan ully now exists in the system 5 al File contained user waypoints only The file stored on the SD card did not contain flight plan only user waypoints One o more of these waypoints did not import successfully Too many points Flight plan truncated waypoints than the system can support waypoints as possible The flight plan on the SD card contains more The flight plan was imported with as many Some waypoints not loaded Waypoints locked 190 01147 01 Rev A or more waypoints that the system cannot find in the navigation database The flight for use Garmin G950 Cockpit Reference Guide for the Tecnam P2006T The flight plan on the SD card contains one plan has been imported but must be edited within the system before it can be activated 83 so1njeoJ 2 Buruuejg AEN 5649 24V oipny uadx sia syu unysu paezey nubi u102 NEN nubi euonippv uoneiedo Jeuuouqy ji 5 x pul Hazard Flight Nav Com Hight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix n Annunciations amp Alerts A GARMIN Flight Plan Import Export Results User waypoint database full Not all loaded Description The flight plan file on the
22. of aircraft The aircraft will penetrate the airspace within 10 minutes ARSPC NEAR Airspace near and ahead Special use airspace is near and ahead of the aircraft position ARSPC NEAR Airspace near less Special use airspace is within 2 nm of the aircraft than 2 nm position 80 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Annunciations amp Alerts MISCELLANEOUS MESSAGE ADVISORIES CONT Message active APR INACTV Approach is not Comments The system notifies the pilot that the loaded approach is not active Activate approach when required frequency for approach SLCT FREQ Select appropriate The system notifies the pilot to load the approach frequency for the appropriate NAV receiver Select the correct frequency for the approach approach SLCT NAV Select NAV on CDI for The system notifies the pilot to set the CDI to the correct NAV receiver Set the CDI to the correct NAV receiver PTK FAIL Parallel track bad geometry unavailable Bad parallel track geometry PTK FAIL Parallel track invalid leg type unavailable Invalid leg type for parallel offset PTK FAIL Parallel track past IAF unavailable IAF waypoint for parallel offset has been passed UNABLE V WPT Can t vertical waypoint each current The current vertical waypoint can not be rea
23. of the departure waypoint or select a waypoint from the submenu of waypoints and press the ENT Key The active flight plan is modified as each waypoint is entered Repeat step numbers 3 and 4 to enter each additional flight plan waypoint When all waypoints have been entered press the FMS Knob to remove the cursor Creating a stored flight plan 1 2 3 4 5 6 7 Press the FPL Key Turn the small FMS Knob clockwise to display the Flight Plan Catalog Page Select the NEW Softkey or press the MENU Key highlight Create New Flight Plan and press the ENT Key to display a blank flight plan for the first empty storage location Turn the small FMS Knob to display the Waypoint Information Window Turning it clockwise displays a blank Waypoint Information Window turning it counter clockwise displays the Waypoint Information Window with a waypoint selection submenu allowing selection of active flight plan nearest recent user or airway waypoints Enter the identifier facility or city name of the departure waypoint or select a waypoint from the submenu of waypoints and press the ENT Key Repeat step numbers 4 and 5 to enter each additional flight plan waypoint When all waypoints have been entered press the FMS Knob to return to the Flight Plan Catalog Page The new flight plan is now in the list Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Pight Planning IM
24. plan This does not delete the stored flight plan only the active flight plan 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sjuauimasu sub 59 oipny uddx UI0JNeN ACN 540 52 suelv uoneiedo sainjea4 aoueplony 2 Duruue d unuuy Jeuuouqy Jeuonippy paezey n xipuaddy x pul Flight Instruments Nav Com XPDR Audio EIS Abnormal Additional Hazard Annun Flight Planning Appendix Alerts Operation Features Avoidance Procedures Index GPS Navigation GARMIN VERTICAL NAVIGATION VNAV The navigation database only contains altitudes for procedures that call for Cross at altitudes If the procedure states Expect to cross at the altitude is not in the database In this case the altitude may be entered manually ACTIVE FLIGHT PLAN eaae Large White 12400FT Text Insertion Poi Large Light Point E Blue Text Indicator Approach KDFW RNAY 17LGPsS LPY 1 Light Blue T Quick ue lext 27 Small Light Blue Subdued Text Small White Text with Altitude Restriction Bar IUSSI Cross AT or ABOVE 5 000 fi VAC B Cross AT 2 300 ft Cinn 11 Cross AT or BELOW 3 000 ft Altitudes associated with approach procedures are auto designated This means the system automatically uses the altitudes loaded with the approach for giving vertical flight path guidance outside the FAF Note these altitudes are displayed as small light
25. position and consequently the system may display a path that is different than the actual movement ofthe aircraft Estimated position information displayed by the G950 through DR while there is no heading and or airspeed data available should not be used for navigation DR Mode is inherently less accurate than the standard GPS SBAS Mode due to the lack of satellite measurements needed to determine a position Changes in wind speed and or wind direction compounds the relative inaccuracy of DR Mode Because of this degraded accuracy the crew must maintain position awareness using other navigation equipment until GPS derived position data is restored 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 63 sepeooid uluueld AEN 540 523 oipny uadx si syuaumasul U105 AeN paezey saunyea4 Jeuonippy sue v unuuy xipueddy x pul iui n Nav Com XPDR Audio Hazard Additional Flight Instruments Flight Planning EIS AFCS GPS Nav Avoidance Procedures Features Annun Appendix Alerts Index Abnormal Operation 64 A GARMIN CDI DR Indication on PFD Symbolic Aircraft Map pages and Inset Map Dead Reckoning Indications As a result of operating in DR Mode all GPS derived data is computed based upon an estimated position and is displayed as yellow text on the display to denote degraded navigation source information This data inc
26. the MFD Apply power to the system check that the databases are initialized and displayed on the power up screen When updating the terrain and FliteCharts databases a Verifying message may be seen If this message is present wait for the system to finish loading before proceeding to step 5 Acknowledge the Power up Page agreement by pressing the ENT Key or the right most softkey Turn the large FMS Knob to select the AUX Page group on the MFD Turn the small FMS Knob to select the System Status Page Monitor the Sync Status in the Database Window Wait for all databases to complete synching indicated by Complete being displayed Remove and reapply power to the system Turn the large FMS Knob to select the AUX Page group on the MFD Turn the small FMS Knob to select the System Status Page Press the Display Database Selection Softkey to show database information for each display MFD1 DB PFD1 DB PFD2 DB Verify the correct database cycle information is shown for each database for each display Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Appendix Loading the leppesen Navigation Database as the Active Navigation Database The leppesen Navigation Database that is loaded to internal memory as the active database vvill be used by the system NOTE Loading the Jeppesen navigation database as the active database prior to its effective date vvill result in the expi
27. 1 AHRS has incorrect software installed The G950 system should be serviced GMU 44 MESSAGE ADVISORIES Message Comments HDG FAULT AHRS1 magnetometer fault has occurred A fault has occurred in the 1 GMU 44 Heading is flagged as invalid The AHRS uses GPS for backup mode operation The G950 system should be serviced MANIFEST GMU1 software mismatch communication halted GDC 74A MESSAGE ADVISORIES The GMU 44 has incorrect software installed The G950 system should be serviced Message Comments MANIFEST GDC1 software mismatch communication halted The GDC 74A has incorrect software installed The G950 system should be serviced 78 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN GDL 69 MESSAGE ADVISORIES Annunciations amp Alerts Message GDL69 CONFIG GDL 69 config error Config service req d Comments GDL 69 configuration settings do not match those of backup configuration memory The G950 system should be serviced GDL69 FAIL GDL 69 has failed A failure has been detected in the GDL 69 The receiver is unavailable The G950 system should be serviced MANIFEST GDL software mismatch communication halted The GDL 69 has incorrect software installed The G950 system should be serviced MISCELLANEOUS MESSAGE ADVISORIES Message FPL WPT LOCK Flight plan
28. ARMIN CREATE A USER WAYPOINT USING THE MAP POINTER 1 Press the Joystick to activate the panning function and pan to the map location of the desired user waypoint 2 Press the ENT Key The User Waypoint Information Page is displayed with the captured position A NOTE If the pointer has highlighted a map database feature one of three things happens upon pressing the ENT Key 1 information about the selected feature is displayed instead of initiating a new waypoint 2 a menu pops up allowing a choice between Review Airspaces or Create User Waypoint or SjueuinJjsu iui olpny uqax 0105 AEN 3 a new waypoint is initiated with the default name being the selected map item 3 Enter a user waypoint name up to six characters 4 Press the ENT Key to accept the selected name 5 If desired define the type and location i e LAT LON RAD RAD or RAD DIS of the waypoint 6 Press the ENT Key to accept the new waypoint 7 If desired change the storage method of the waypoint to TEMPORARY or NORMAL by moving the cursor to TEMPORARY and selecting the ENT Key to check or uncheck the box 8 Press the FMS Knob to remove the flashing cursor 9 Press the GO BACK Softkey to return to the map page DELETE A USER WAYPOINT 1 Tum the large FMS Knob to select the WPT page group 2 Turn the small FMS Knob to select the User WPT Information Page 3 Press the FMS Knob to activate the cu
29. CE PFD1 needs ervice Return unit for repair The PFD and or MFD self test has detected a n MFD1 SERVICE MFD1 needs ervice Return unit for repair problem The G950 system should be serviced MANIFEST PFD1 software mismatch communication halted MANIFEST MFD1 software mismatch communication halted The PFD and or MFD has incorrect software installed The G950 system should be serviced Config service req d 190 01147 01 Rev A PFD1 CONFIG PFD1 config error The PFD configuration settings do not match backup configuration memory The G950 system should be serviced Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 69 s m eouepioAy s mp oold Buruue d AEN Sd5 2 oipny uddx sia Sjueumasu paezey nubi Wil jeuonippy uoneiedo Jeuuouqy ES x pul Hazard Flight Nav Com Flight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix d Annunciations amp Alerts A GARMIN MFD amp PFD MESSAGE ADVISORIES Message Comments MFD1 CONFIG MFD1 config error Config service req d The MFD configuration settings do not match backup configuration memory The G950 system should be serviced SW MISMATCH GDU software version mismatch Xtalk is off The MFD and PFDs have different software versions installed The G950 system should be serviced
30. EXRAD XM LTNG PROFILE and or METAR softkeys are selected if installed Returns to top level softkeys Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Appendix Level 1 Level 2 Level3 Description DCLTR Selects desired amount of map detail cycles through declutter levels DCLTR No Declutter All map features visible DCLTR 1 Declutters land data DCLTR 2 Declutters land and SUA data DCLTR 3 Removes everything except the active flight plan LOADING UPDATED DATABASES Ay CAUTION Never disconnect power to the system when loading a database Power interruption during the database loading process could result in main tenance being required to reboot the system NOTE When loading database updates the DB Mismatch message will be displayed until database synchronization is complete followed by turning system power off then on Synchronization can be monitored on the AUX SYSTEM STATUS Page In some cases it may be necessary to obtain an unlock code from Garmin in order to make the database product functional It may also be necessary to have the system configured by a Garmin authorized service facility in order to use some database features If an error occurs during synchronization an error message will be displayed followed by the affected display in the Sync Status section of the Database Window 1f synchronization completes on
31. Ensure that the data card is properly inserted Replace data card If problem persists The G950 system should be serviced MFD1 DB ERR MFD1 airport terrain database missing PFD1 DB ERR PFD1 airport terrain database missing The airport terrain database is present on another LRU but is missing on the specified LRU MFD1 DB ERR MFD1 Safe Taxi database error exists PFD1 DB ERR PFD1 Safe Taxi database error exists The MFD and or PFD detected a failure in the Safe Taxi database Ensure that the data card is properly inserted Replace data card If problem persists The G950 system should be serviced 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T soJnjeoJ 2 AEN Sd 2 oipny uadx sia s u un sul paezey nubi euonippv uoneiedo Jeuuouqy iic EST x pul Hazard Flight Nav Com Fight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix 5 Annunciations 8 Alerts A GARMIN DATABASE MESSAGE ADVISORIES CONT Message MFD1 DB ERR MFD1 multiple database errors exist PFD1 DB ERR PFD1 multiple database errors exist Comments The MFD and or PFD detected a failure in more than one database If problem persists the system should be serviced DB MISMATCH N
32. FD 3 Turn the small FMS Knob to select the Flight Plan Catalog Page 4 Press the FMS Knob to activate the cursor 5 Turn the large FMS Knob to highlight the flight plan to be exported 6 Press the EXPORT Softkey 7 Press the ENT Key to confirm the export 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 33 oipny uddx s q sjuauimasu U105 AEN 3463 52 2 4 AEN 540 nubi eouepioAy paezey suelv uoneiedo sainjea4 Tunuuy Jeuuouqy Jeuonippy xipuaddy x pul GARMIN Flight Planning Ssjueuinijsu fila 59 oipny uadx U105 AEN s24v AeN Sd5 buluueld 346 Blank Page 5 2 4 puezey saunjea4 jeuonippy uoneiedo jeuuouqy suay unuuy x pu ddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 34 A GARMIN Procedures PROCEDURES LOAD AND ACTIVATE A DEPARTURE PROCEDURE 1 Press the PROC Key 2 Tum the large F MS Knob to highlight SELECT DEPARTURE 3 Press the ENT Key The cursor is displayed in the DEPARTURE field with a list of available departures 4 Turn the large FMS Knob to highlight the desired departure 5 Press the ENT Key A list of runways may be displayed for the departure If so turn either FMS Knob to select the desired runway 6 Press the ENT Key The cursor is displayed in the TRANSITI
33. FD and or PFD detected a failure in the basemap database 70 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Annunciations amp Alerts DATABASE MESSAGE ADVISORIES CONT Message MFD1 DB ERR MFD1 terrain database error exists PFD1 DB ERR PFD1 terrain database error exists Comments The MFD and or PFD detected a failure in the terrain database Ensure that the terrain card is properly inserted in display Replace terrain card If problem persists The G950 system should be serviced MFD1 DB ERR MFD1 terrain database missing PFD1 DB ERR PFD1 terrain database missing The terrain database is present on another LRU but is missing on the specified LRU MFD1 DB ERR MFD1 obstacle database error exists PFD1 DB ERR PFD1 obstacle database error exists The MFD and or PFD detected a failure in the obstacle database Ensure that the data card is properly inserted Replace data card If problem persists The G950 system should be serviced MFD1 DB ERR MFD1 obstacle database missing PFD1 DB ERR PFD1 obstade database missing The obstacle database is present on another LRU but is missing on the specified LRU MFD1 DB ERR MFD1 airport terrain database error exists PFD1 DB ERR PFD1 airport terrain database error exists The MFD and or PFD detected a failure in the airport terrain database
34. Flight Plan reete ten tane en ee Delete a Flight Plan Graphical Flight Plan Creation Export a Flight Plan to an SD Card 33 PROCEDURES o Bad a Load and Activate a Departure Procedure Activate A Departure Leg ssssseeeeeenennnnnnnnnns Load An Arrival Procedure Activate An Arrival Leg Load and or Activate an Approach Procedure 37 Activate An Approach in the Active Flight Plan 38 Activate a Vector to Final Approach Fix sssss 38 Activate A Missed Approach in the Active Flight 7 56 38 HAZARD AVOIDANCE 1 ntt 39 Customizing the Hazard Displays on the Navigation 39 XM WX Satellite Weather If Installed Traffic Information Service Terrain And Obstacle Proximity sse Terrain SVS If Installed sssssssns Terrain Awareness amp Warning System TAWS B Display If Installed 46 ADDITIONAL FEATURES UL naissance ibis Synthetic Vision If Installed sss Terminal Procedure Charts AOPA Airport Directory If Installed A
35. G950 Integrated Flight Deck Cockpit Reference Guide for the Tecnam P2006T y A GARMIN Copyright O 2010 2011 Garmin Ltd or its subsidiaries All rights reserved ual So ual This man P2006T this man Ga Tel to earlier or later software versions m 91 n Inte 3 397 8200 m 5 n n Ga Tel ALI 03 391 3411 thampton 5040 9RB U K 44 0870 8501241 n Ga Sou Tel n Garmin Corporation No 68 Jangshu 2nd Road Tel 886 02 2642 9199 STI 0 an d int Web Site Address www garmin com Except transm as expressly provided herein no part itted disseminated downloaded or sto without the express written permission download a single copy of this man other electronic storage medium to or printed copy of this manual or notice and provided further that revision hereto is strictly prohibit be v evisi ot ohibited in Ltd or i in Ltd or of Garmin G950 is a trademark of Garm registered trademarks of Garm without the express permission NavData is a registered trademark of Jeppese AOPA Membership Publications Inc and its AOPA expressly disclaim all warranties with data express or implied including but not lim any unauthorized commercia Fax 913 397 8282 c 2345 Turner Road SE Salem OR 97302 U S A Fax 503 364 2138 Fax 44 0870 8501251 Shijr
36. IVATE APPROACH Press the ENT Key ACTIVATE A VECTOR TO FINAL APPROACH FIX 1 2 3 4 Press the PROC Key Turn the large FMS Knob to highlight ACTIVATE VECTOR TO FINAL Press the ENT Key The final approach course becomes the active leg ACTIVATE A MISSED APPROACH IN THE ACTIVE FLIGHT PLAN 1 2 3 4 38 Press the PROC Key Turn the large FMS Knob to highlight ACTIVATE MISSED APPROACH Press the ENT Key A confirmation window is displayed With ACTIVATE highlighted press the ENT Key Or Press the Go around Button Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Hazard avoidance HAZARD AVOIDANCE CUSTOMIZING THE HAZARD DISPLAYS ON THE NAVIGATION MAP 1 With the Navigation Map Page displayed press the MENU Key to display the Navigation Map Page Menu The cursor flashes on the Map Setup option 2 Press the ENT Key The Map Setup Menu is displayed Turn the small FMS Knob to select Weather to customize the display of weather features Select Traffic to customize the display of traffic 3 Press the small FMS Knob to return to the Navigation Map Page XM WX SATELLITE WEATHER IF INSTALLED WARNING Use of XM WX Satellite Weather for hazardous weather penetration is not recommended Weather information provided by SiriusXM Radio Service is approved only for weather avoidance not penetration Displaying XM WX on the Navigation M
37. ON field with a list of available transitions 7 Tum the large FMS Knob to highlight the desired transition 8 Press the ENT Key 9 With LOAD highlighted press the ENT Key The departure is active when the flight plan is active ACTIVATE A DEPARTU RE LEG Activate leg using the Quick Select Box 1 Press the FPL Key on the MFD to display the active flight plan 2 Use the Joystick to move the Quick Select Box to the TO waypoint of the desired leg with 3 Press the ACT LEG Softkey A confirmation window showing the selected leg is displayed 4 With ACTIVATE in the departure highlighted press the ENT Key Activate leg using the cursor 1 Press the FPLK ey on the MFD to display the active flight plan 2 Press the FMS Knob to activate the cursor 3 Turn the large FMS Knob to highlight the desired waypoint within the departure 4 Press the ACT LEG Softkey A confirmation window showing the selected leg is displayed 5 With ACTIVATE 190 01147 01 Rev A highlighted press the ENT Key Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 35 oipny uddx 59 sjuauimasu U10 AEN fija 52 AEN 540 Duruue d ni s mp old eouepioAy paezey suelv uoneiedo sainjea4 Tunuuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Procedures Abnormal Additional Hazard Annun Flight Instruments Flight Planning EIS AFCS GPS Nav
38. PORT A FLIGHT PLAN FROM AN SD CARD NOTE See the Annunciations amp Alerts section for flight plan import message descriptions 1 Insert the SD card containing the flight plan in the top card slot on the MFD 2 Press the FPL Key on the MFD to display the Active Flight Plan Page 3 Turn the small FMS Knob to select the Flight Plan Catalog Page 4 Press the FMS Knob to activate the cursor 5 Turn either FMS Knob to highlight an empty or existing flight plan 6 Press the IMPORT Softkey If an empty flight plan is selected a list of the available flight plans on the SD card will be displayed Or If an existing flight plan is selected an Overwrite existing flight plan OK or CANCEL prompt is displayed Press the ENT Key to choose to overwrite the selected flight plan and see a list of the available flight plans on the SD card If overwriting the existing flight plan is not desired select CANCEL using the FMS Knob press the ENT Key select another existing or empty flight plan and again press the IMPORT Softkey 7 Turn the small FMS Knob to highlight the desired flight plan for importing 8 Press the ENT Key saunpadold 4 AEN 540 nubi INSERT A WAYPOINT IN THE ACTIVE FLIGHT PLAN 1 Press the FPL Key to display the active flight plan 2 Press the FMS Knob to activate the cursor not required on the PFD and turn the large FMS Knob to move Insertion Point Indicator to the location for the new wayp
39. R Key is pressed again the message is restored Press the ENT Key while the message line is cleared to clear the message time AUXILIARY VIDEO IF INSTALLED NOTE Images provided on the AUX VIDEO Page are for supplemental use only There are four modes of operation of the optional auxiliary video display Full Screen Full Screen with Digital Zoom Split Sereen with Map and Split Screen with Map and Digital Zoom Displaying auxiliary video 1 2 Turn the large FMS Knob to select the AUX page group Turn the small FMS Knob to select VIDEO and display the AUX VIDEO Page The video display softkeys shown below appear on the AUX VIDEO Page Control of the AUX VIDEO Page can also be accessed through the Page Menu Selecting video menu options 1 2 While viewing the AUX VIDEO Page press the MENU Key to display the Page Menu OPTIONS Turn the large FMS Knob to highlight the desired video adjustment option and press the ENT Key Once the ENT key is pressed on any option the page menu closes and returns to the AUX VIDEO Page 54 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Video Setup Additional Features Video brightness contrast and saturation may be adjusted be selecting the setup function While viewing the setup function softkeys after 45 seconds of softkey inactivity the system reverts to the AUX VIDEO Page softkeys Adjusting the vide
40. S1 SERVICE G S1 needs service Return unit for repair G S2 SERVICE G S2 needs service Comments A failure has been detected in glideslope receiver 1 and or receiver 2 The receiver may still be available The G950 system should be serviced when possible FAILED PATH A data path has failed A data path connected to the GDU or the GIA 63W has failed GTX 33 MESSAGE ADVISORIES Message Comments XPDR1 CONFIG XPDR1 config error Config service req d The transponder configuration settings do not match those of backup configuration memory The 950 system should be serviced MANIFEST GTX1 software mismatch communication halted The transponder has incorrect software installed The G950 system should be serviced XPDR1 SRVC XPDR1 needs service Return unit for repair The 1 transponder should be serviced when possible XPDR1 FAIL XPDR1 is inoperative There is no communication with the 1 transponder GRS 77 MESSAGE ADVISORIES Message AHRS1 TAS AHRS1 not receiving valid airspeed Comments The 1 AHRS is not receiving true airspeed from the air data computer The AHRS relies on GPS information to augment the lack of airspeed The G950 system should be serviced AHRS1 GPS AHRS1 using backup GPS source The 1 AHRS is using the backup GPS path Primary GPS path has failed The G950 system should be serviced when pos
41. Tecnam P2006T Senpa304d Buruue d AEN 540 52 oipny uddx 53 s3u uin sul piezeH ubi U10 AEN ubiu so1njeoJ jeuonippy Sue v unuuy xipuaddy x pul Flight Instruments Nav Com XPDR Audio Flight Planning Hazard Additional Annun EIS AFCS GPS Nav Avoidance Procedures Features Appendix Alerts Index Abnormal Operation UNUSUAL ATTITUDES A GARMIN The PFD declutters when the aircraft enters an unusual attitude Only the primary functions are displayed in these situations The following information is removed from the PFD and corresponding softkeys are disabled when the aircraft experiences unusual attitudes 62 Traffic Annunciations AFCS Annunciations Flight director Com mand Bars Inset Map Temperatures DME Information Window Wind Data Selected Heading Box Selected Course Box Transponder Status Box System Time PFD Setup Menu Windows displayed in the lower right corner of the PFD Timer References Nearest Airports Flight Plan Messages Procedures DME Tuning Barometric Minimum Descent Altitude Box Glideslope Glide path and Vertical Deviation Indicators Altimeter Barometric Setting Selected Altitude VNV Target Altitude Garmin G950 Cockpit Reference Guide for the Tecnam P2006T Extreme Pitch Indication 190 01147 01 Rev A GARMIN Abnormal operation DEAD RECKONING While in Enroute or Oceanic phase of f
42. The position of the se is not calcu reference datum and may be positioned in error as displayed Do not ected waypoint xxxx lated based on the WGS84 map use GPS to navigate to the selected non WGS84 waypoint TRAFFIC FAIL Traffic device has The G950 is no longer receiving data from the traffic failed system The traffic device should be serviced FAILED PATH A data path has failed A data path 63 W has fai connected to the GDU or the GIA ed MAG VAR WARN Large magnetic The GDU s internal model cannot determine the variance Verify all course angles exact magnetic variance for geographic locations near the magnetic poles Displayed magnetic course angles may differ from the actual magnetic heading by more than 2 SCHEDULER message Message criteria entered by the user CHECK CRS Database course for 1 Selected course for LOC1 differs from published LOC1 LOC ID is CRS localizer course by more than 10 degrees CHECK CRS Database course for 1 Selected course for LOC2 differs from published LOC2 LOC ID is CRS 9 localizer course by more than 10 degrees PFD1 or MFD1 CARD 1 REM Card 1 was removed Reinsert card The SD card was removed from the top card slot of the spec ified PFD or MFD The SD card needs to be reinserted PFD1 or MFD1 CARD 2 REM Card 2 was removed Reinsert card The SD card was removed from the botto
43. US and Canada The age of the displayed data for each is shown at the right SURFACE ANALYSIS with CITY FORECAST The upper symbol depicts Surface Analysis The lower symbol depicts City Forecast The age of the displayed data for each is shown at the right The selected forecast period is shown at the bottom 40 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Hazard Avoidance Wx Product Status Icons Description 4m FREEZING LEVEL The age of the displayed data is shown at the right PT 8m CN 12m 3000F1 WINDS ALOFT Available for the US and Canada The age of the displayed data for each is shown at the right The altitude selection is shown at the bottom COUNTY WARNING The age of the displayed data is shown at the right 2m CYCLONE WARNING The age of the displayed data is shown at the right AIREP The age of the displayed data is shown at the right 68m 21000F1 PIREP The age of the displayed data is shown at the right Urgent Pireps are displayed in yellow TURBULENCE The age of the displayed data is shown at the right The altitude selection is shown at the bottom 4m 6000FT ICING POTENTIAL The age of the displayed data is shown at the right The altitude selection is shown at the bottom No Status Icon TFR Depicted as an area outlined in yellow 190 01147 01 Rev A G
44. WPT Information Page 3 Press the NEW Softkey A waypoint is created at the current aircraft position 4 Enterthe desired waypoint name 5 Press the ENT Key 6 The cursor is now in the WAYPOINT TYPE field If desired the waypoint can be made temporary deleted automatically when the system is turned off If the waypoint is to remain in the system proceed to step 7 a Turn the large FMS Knob one click to the left to highlight TEMPORARY b Press the ENT Key to place a check mark in the box Turn the large FMS Knob to place the cursor back in the WAYPOINT TYPE field 7 With the cursor in the WAYPOINT TYPE field turn the small FMS Knob to display a list of waypoint types 8 Tum the small FMS Knob to select RAD DIS radial distance 9 Press the ENT Key 10 The cursor moves to the REFERENCE WAYPOINTS field With the first waypoint name highlighted use the FMS Knobs to enter the desired waypoint name Waypoints may also be selected as follows 2 4 AEN 540 nubi a When a flight plan is active turning the small FMS Knob to the left will display a list of the flight plan waypoints b Turn the large FMS Knob to select the desired waypoint Press the ENT Key 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 23 eouepioAy paezey suelv uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy xipueddy x pul Nav Com XPDR A
45. age is displayed press the MENU Key 2 Turn the small FMS Knob to select Enable TAWS 3 Press the ENT Key Displaying Terrain and Obstacles on the Navigation Map 1 With the Navigation Map displayed press the MAP Softkey 2 Press the TERRAIN Softkey Terrain and obstacle proximity will now be displayed on the map 3 Terrain and obstacles may be displayed in the Profile View by selecting the PROFILE Softkey 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 4 AEN Sd5 S24V oipny uddx sia siu umninsul Tuo2 AEN iui Duruue d nubi e uepioAy s mp oold paezey SH V uoneiedo sainjea4 Tunuuy Jeuuouqy Jeuonippy xipueddy x pul GARMIN Hazard Avoidance Sjueuinijsu fila 59 oipny uadx U105 AEN S2dV AeN Sd5 Duruue d Blank Page 6 2 4 eouepioAy DX Se1njeoJ jeuonippy uoneiedo jeuuouqy suay junuuy xipuaddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 48 GARMIN Additional Features ADDITIONAL FEATURES SYNTHETIC VISION IF INSTALLED o V ARNING Use appropriate primary systems for navigation and for terrain obstacle and traffic avoidance SVS is intended as an aid to situational awareness only and may not provide the accuracy and or fidelity upon which to solely base decisions and or plan maneuvers to avoid terrain obstacles or traffic
46. age timer reaches zero Press the ENT Key again or use the large FMS Knob to move the cursor to the next field For periodic and one time message use the FMS Knob to enter the timer value HH MM SS from which to countdown and press the ENT Key For event based messages a Use the FMS Knob to enter the desired date DD MM YY and press the ENT Key b Press the ENT Key again or use the large FMS Knob to move the cursor to the next field 53 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 2 Buruuejd AeN Sd5 S24V olpny uqax sia siu u nnsul Tu102 AEN 346 aoueplony paezey s mie q jeuonippy xipuaddy Suelv uoneiedo junuuy Jeuuouqy x pul Flight Instruments Nav Com XPDR Audio Flight Planning Hazard Avoidance Additional Features Abnormal Annun EIS AFCS GPS Nav Procedures Appendix Alerts Operation Index A Additional Features Use the FMS Knob to enter the desired time HH MM and press the ENT Key 10 Press the ENT Key again or use the large FMS Knob to move the cursor to enter the next message Delete a Scheduler Message 1 2 3 4 5 Select the AUX Utility Page Press the FMS Knob momentarily to activate the flashing cursor Turn the large FMS Knob to highlight the name field of the scheduler message to be deleted Press the CLR Key to clear the message text If the CL
47. ap Page 1 Press the MAP Softkey 2 Press the NEXRAD or XM LTNG Softkey to display the desired weather Press the applicable softkey again to remove weather data from the Navigation Map Page Display METAR and TAF information on the Airport Information Page 1 Turn the large FMS Knob to select the WPT Page Group 2 Turn the small FMS Knob to select the Airport Information Page 3 Press the WX Softkey to display METAR and TAF text METAR and TAF information is updated every 12 minutes Displaying Weather on the Weather Data Link Page 1 Tum the large FMS Knob to select the Map Page Group 2 Turn the small FMS Knob to select the Weather Data Link Page 3 Press the available softkeys to select the desired XM weather product 4 Press the LEGEND Softkey to view the legends for the selected products If necessary turn either FMS Knob to scroll through the list Press the small FMS Knob or the ENT Key to return to the map 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 3 SjueuinJjsu iui APN 540 523 olpny uadX uo2 AEN Duruue d ELTE 2 4 paezey saunqea4 jeuonippy Suelv uoneiedo junuuy Jeuuouqy xipuaddy x pul Nav Com XPDR Audio Abnormal Additional Annun Flight Instruments Flight Planning EIS AFCS GPS Nav Hazard Avoidance Procedures Appendix Alerts Operation Features Index Hazard Avoidance A GARMIN M
48. ap Panning Information Weather Data Link Page 1 2 Push in the Joystick to display the panning arrow Move the Joystick to place the panning arrow on AIRMETs TFRs METARs or SIGMETs 3 Press the ENT Key to display pertinent information for the selected product Note that pressing the ENT Key when panning over an AIRMET or a SIGMET displays an information box that shows the text of the report Panning over an airport with METAR information does not display more information but allows the user to press the ENT Key and select that Airport s Information Page to display the text of the report Pressing the ENT Key when panning over a TFR displays TFR specific information XM WX Satellite Weather Products and Symbols Wx Product Status Icons Description US 3m CN Bm s NEXRAD Available for the US and Canada The age of the displayed data for each is shown at the right b 5m ECHO TOP The age of the displayed data is shown at the right Not displayed when CLOUD TOP is displayed 12m CLOUD TOP The age of the displayed data is shown at the right Not displayed when ECHO TOP is displayed 3m 4 XM LIGHTNING The age of the displayed data is shown at the right 2m SIGMET 2m AIRMET 5m CELL MOVEMENT The age of the displayed data is shown at the right SIGMET amp AIRMET The age of the displayed data for each is shown at the right METAR Available for the
49. arge FMS Knob to select the GROUP field Turn the small FMS Knob to select the desired procedure and press the ENT Key Turn the large FMS Knob to select the CHECKLIST field Turn the FMS Knob to select the desired checklist and press the ENT Key The selected checklist item is indicated with white text surrounded by a white box Press the ENT Key or CHECK Softkey to check the selected checklist item The line item turns green and a checkmark is placed in the associated box The next line item is automatically selected for checking Either FMS Knob can be used to scroll through the checklist and select the desired checklist item Press the CLR Key or UNCHECK Softkey to remove a check mark from an item When all checklist items have been checked Checklist Finished is displayed in green text at the bottom left of the checklist window If all items in the checklist have not been checked CHECKLIST NOT FINISHED will be displayed in yellow text Press the ENT Key GO TO NEXT CHECKLIST will be highlighted by the cursor Press the ENT Key to advance to the next checklist Press the EXIT Softkey to exit the Checklist Page and return to the page last viewed Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Additional Features Immediately Accessing Emergency Procedures 1 From any page on the MFD press the CHKLIST Softkey 2 Press the EMERGCY Softkey 3 Turn t
50. armin G950 Cockpit Reference Guide for the Tecnam P2006T AEN Sd5 S24V oipny uddx sia Sjuoumajsul sub Duruue d nubi e uepioAy s mp oold paezey sualy uonesado saunqea4 junuuy jeuuouqy euonippy xipuaddy x pul Nav Com XPDR Audio Abnormal Additional Annun Flight Instruments Flight Planning EIS AFCS GPS Nav Hazard Avoidance Procedures Appendix Alerts Operation Features Index Hazard Avoidance A GARMIN TRAFFIC INFORMATION SERVICE Traffic Symbol Description e Non Threat Traffic intruder is beyond 5 nm and greater than 1200 vertical separation O Traffic Advisory TA dosing rate distance and vertical separation meet TA citeria amp Traffic Advisory Off Scale Traffic Symbol Description NOTE Traffic Information Service TIS is only available when the aircraft is within the service volume of a TIS capable terminal radar site Displaying Traffic on the Traffic Map Page 1 2 3 4 5 6 Turn the large FMS Knob to select the Map Page Group Turn the small FMS Knob to select the Traffic Map Page Press the OPERATE Softkey to begin displaying traffic OPERATING is displayed in the Traffic Mode field Press the STANDBY Softkey to place the system in the Standby Mode STANDBY is displayed in the Traffic Mode field Rotate the Joystick clockwise to display a larger area or rotate counter clockwise to displ
51. atellite Weather GFDS Worldwide Weather or FIS B for hazardous weather penetration Weather information provided by these products is aged by up to several minutes and may not depict actual weather conditions as they currently appear WARNING NEXRAD weather data is to be used for long range planning purposes only Due to inherent delays in data transmission and the relative age of the data NEXRAD weather data should not be used for short range weather avoidance WARNING The Garmin G950 has a very high degree of functional integrity However the pilot must recognize that providing monitoring and or self test capability for all conceivable system failures is not practical Although unlikely it may be possible for erroneous operation to occur without a fault indication shown by the G950 It is thus the responsibility of the pilot to detect such an occurrence by means of cross checking with all redundant or correlated information available in the cockpit WARNING For safety reasons G950 operational procedures must be learned on the ground WARNING The United States government operates the Global Positioning System and is solely responsible for its accuracy and maintenance The GPS system is subject to changes which could affect the accuracy and performance of all GPS equipment Portions of the Garmin G950 utilize GPS as a precision electronic NAVigation AID NAVAID Therefore as with all NAVAIDs information pr
52. ature GIA1 COOLING GIA1 over GIA2 COOLING GIA2 over The GIA1 and or GIA2 temperature is too high If problem persists the G950 system should be serviced GIA1 SERVICE GIA1 needs service Return the unit for repair GIA2 SERVICE GIA2 needs service Return the unit for repair The GIA1 and or GIA2 self test has detected a problem in the unit The G950 system should be serviced halted HW MISMATCH GIA hardware mismatch GIA1 communication HW MISMATCH GIA hardware AGIA mismatch has been detected where only one is SBAS capable mismatch GIA2 communication halted MANIFEST GIA1 software mismatch communication halted The GIAT and or GIA 2 has incorrect software MANIFEST GIA2 software installed The G950 system should be serviced mismatch communication halted MANIFEST GFC software Incorrect servo software is installed or gain mismatch communication halted settings are incorrect 74 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Annunciations 8 Alerts GIA 63W MESSAGE ADVISORIES CONT Config service req d Message Comments MANIFEST COM1 software mismatch communication halted COM1 and or COM2 software mismatch The MANIFEST COM software system should be serviced mismatch communication halted MANIFEST NAV1 software mismatch
53. avigation database mismatch Xtalk is off The PFDs and MFD have different navigation database versions or regions installed Crossfill is off Check the AUX SYSTEM STATUS Page to determine versions or regions Also check the AUX SYSTEM STATUS Page for a database synchronization function not completed After synchronization is complete power must be turned off then on DB MISMATCH Standby Navigation database mismatch The PFDs and MFD have different standby navigation database versions or regions installed Check the AUX SYSTEM STATUS Page to determine versions or regions Also check the AUX SYSTEM STATUS Page for a database synchronization function not completed After synchronization is complete power must be turned off then on DB MISMATCH Terrain database mismatch The PFDs and MFD have different terrain database versions or regions installed Check the AUX SYSTEM STATUS Page to determine versions or regions Also check the AUX SYSTEM STATUS Page for a database synchronization function not completed After synchronization is complete power must be turned off then on DB MISMATCH Obstacle database mismatch The PFDs and MFD have different obstacle database versions or regions installed Check the AUX SYSTEM STATUS Page to determine versions or regions Also check the AUX SYSTEM STATUS Page for a database synchronization function not completed After synchronization is complete pow
54. away from the source of the interference should alleviate the condition NOTE Use of polarized eyewear may cause the flight displays to appear dim or blank NOTE The purpose of this Cockpit Reference Guide is to provide the pilot a resource with which to find operating instructions on the major features of the G950 system more easily It is not intended to be a comprehensive operating guide Complete operating procedures for the system are found in the G950 Pilot s Guide for this aircraft Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Record of Revisions Part Number Change Summary 190 01147 00 190 01147 01 Added GDU 12 03 parameters Added Flight Plan enhancements Added XM WX Satellite Weather if installed Added Terrain SVS if installed Added TAWS B if installed Added Satellite Radio if installed Added Terminal Procedures Charts if installed Added SVS if installed Added AUX Video if installed Updated Database upload procedures Added MV DB update procedure Ronen Date of Revision Affected Pages December 201 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T Record of Revisions GARMI Blank Page RR 2 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Tale of Contents FLIGHT INSTRUMENTS 1 Selecting t
55. ay a smaller area Press the TNA MUTE Softkey to mute the Traffic Not Available aural alert Displaying Traffic on the Navigation Map 1 2 42 Ensure TIS is operating With the Navigation Map displayed press the MAP Softkey Press the TRAFFIC Softkey Traffic is now displayed on the map Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Hazard Avoidance TERRAIN AND OBSTACLE PROXIMITY NOTE Terrain data is not displayed when the aircraft is outside the installed terrain database coverage area Displaying Terrain and Obstacles on the Terrain Proximity Page 1 2 3 4 Turn the large FMS Knob to select the Map Page Group Turn the small FMS Knob to select the last rectangular page icon If desired press the VIEW Softkey to access the ARC and 360 Softkeys When the ARC Softkey is pressed a radar like 120 view is displayed Press the 360 Softkey to return to the 360 default display Rotate the Joystick clockwise to display a larger area or rotate counter clockwise to display a smaller area Terrain Obstacle Location Terrain Obstacle above or within 100 below current aircraft altitude Terrain Obstade between 100 and 1000 below current aircraft altitude Terrain Obstacle is more than 1000 Black below aircraft altitude Displaying Terrain and Obstacles on the Navigation Map 1 2 With the Navigation Map displayed press the MAP
56. ce the database effective date is not yet valid it should not be loaded as the active database The display now starts in normal mode Do not remove power while the display is starting Press the ENT Key to acknowledge the startup screen Turn the large FMS Knob to select the AUX Page group on the MFD 10 Turn the small FMS Knob to select the System Status Page 11 The new database is copied to the SD card in the bottom card slot of each 94 PFD Progress can be monitored in the SYNC STATUS field When copying is finished Complete is displayed NOTE During the synchronization process version differences between standby navigation databases will exist This will result in the system displaying a DB Mismatch alert for the standby navigation databases This alert will remain until the next power cycle Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN 000 Appendix 12 Turn system povver OFF 13 Remove the SD card from the top card slot of the MFD 14 Turn system power ON 15 Press the ENT Key to acknowledge the startup screen 16 Turn the large FMS Knob to select the AUX Page group on the MFD 17 Turn the small FMS Knob to select the System Status Page 18 Press the Display Database Selection Softkey to shovv standby navigation database information for each display MFD1 DB PFD1 DB PFD2 DB Verify the correct standby navigation database cycle information is shovvn for each
57. ched within the maximum flight path angle and vertical speed constraints The system automatically transitions to the next vertical waypoint type in flight plan VNV Unavailable Unsupported leg The lateral flight plan contains a procedure turn vector or other unsupported leg type prior to the active vertical waypoint This prevents vertical guidance to the active vertical waypoint angle error VNV Unavailable Excessive track The current track angle error exceeds the limit causing the vertical deviation to go invalid crosstrack error VNV Unavailable Excessive The cu vertica rent crosstrack exceeds the limit causing deviation to go invalid selected VNV Unavailable Parallel course A parallel course has been selected causing the vertical deviation to go invalid 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T saunqea4 2 AEN Sd 24V olpny uqax sia syu unysu paezey nubi Juo ney Wil jeuonippy uoneiedo Jeuuouqy Bi PET x pul Hazard Flight Nav Com Flight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix Annunciations amp Alerts A GARMIN MISCELLANEOUS MESSAGE ADVISORIES CONT Message Comments NON WGS84 WPT Do not use GPS for navigation to xxxx
58. ciator Annunciator Selected radios aural alerts pilot copilot passengers music Selected radios aural alerts pilot radios aural alerts pilot passengers music Selected radios aural alerts pilot copilot Selected ON m radios aural alert copi pass musi Copi pass s pilot ot engers C lot engers mus Copi ic lot Selected radios aural alerts pilot copilot ICS Isolation Modes 190 01147 01 Rev A Nav Com XPDR Audio Panel Selected radios aural alerts pilot copilot passengers music Copilot passengers music Selected radios aural alerts pilot passengers music Passengers music Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sjueumasu 59 S24V oipny uddx JUI05JAEN sual uonesado s n e 4 s mp oold Buruue d AEN Sd5 junuuy jeuuouqy feuonippv xipuaddy x pul iui nu paezey GARMIN Nav Com XPDR Audio Panel Sjueuinijsu fila 59 oipny uadx U10 AeEN s24v AeN Sd5 buluueld r Blank Page 6 2 4 aoueplony puezey saunjea4 jeuonippy uoneiedo jeuuouqy suay unuuy x pu ddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 10 A GARMIN 008080 A AFCs AUTOMATIC FLIGHT CONTROL SYSTEM NOTE Refer to the Pilot s Operating Handbook POH and or Airplane Flight Manual AFM for the i
59. communication halted NAV1 and or NAV2 software mismatch The MANIFEST NAV2 software system should be serviced mismatch communication halted COM1 CONFIG 1 config pt error Config service req d COM and or COM2 configuration settings do not r match backup configuration memory The system COM2 CONFIG COM config error should be serviced COM1 TEMP COM over temp Reducing transmitter power COM2 TEMP COM2 over temp Reducing transmitter power The system has detected an over temperature condition in COM1 and or COM2 The transmitter is operating at reduced power f the problem persists the G950 system should be serviced COM1 SERVICE COM1 needs service Return unit for repair COM2 SERVICE COM2 needs service Return unit for repair The system has detected a failure in COM1 and or COM2 COM1 and or COM2 may still be usable The G950 system should be serviced when possible COMI PTT COM1 push to talk key is stuck key is stuck COM2 PTT COM2 push to talk The COM1 and or COM2 external push to talk switch is stuck in the enable or pressed position Press the PTT switch again to cycle its operation If the problem persists the G950 system should be serviced COM1 RMT XFR COM1 remote transfer key is stuck COM2 RMT XFR COM2 remote transfer key is stuck The COM1 and or COM2 transfer switch is stuck in the enabled or pressed positio
60. d if installed meer GS 9 9 CS owe Dow ser pee wr n nN FSH HU 75 75 UU J pers wno L owe ene HsirRvril ene atun sTo sarol Back ALERTS BAGH GPS BAGH NAVI prazna Press the BACK Softkey to return to the top level softkeys BRG2 GPS BRG2 0FF METERS l amp c ALERTS 5 75 mumu LC Com TL erm J omes L o TL L L Tater PFD Configuration Softkeys 86 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Appendix Level 1 Level 2 Level 3 Description PFD DFLTS VVIND DME BRGI HSI FRMT BRG2 ALT UNIT 190 01147 01 Rev A OPTN 1 OPTN 2 OPTN 3 OFF 360 HSI ARC HSI METERS IN HPA Displays second level softkeys for additional PFD configurations Resets PFD to default settings including changing units to standard Displays softkeys to select wind data parameters Longitudinal and lateral components Total direction and speed Total direction with head and crosswind speed components Information not displayed Displays the DME Information VVindovv Cycles the Bearing 1 Information Window through NAV1 or GPS vvaypoint identifter and GPS derived distance information Displays the HSI formatting softkeys Displays the HSI in a 360 degree format Di
61. d flight plan contains procedures that have been manually edited This alert is issued only after an navigation database update Verify that the user modified procedures in stored flight plans are correct and up to date DB CHANGE Database changed Verify stored airways This occurs when a stored flight plan contains an airway that is no longer consistent with the navigation database This alert is issued only after an navigation database update Verify use of airways in stored flight plans and reload irways as needed ab FPL TRUNC Flight plan has been truncated This occurs when a newly installed navigation database eliminates an obsolete approach or ival used by a stored flight plan The obsolete procedure is removed from the flight plan Update flight plan with current arrival or approach ab LOCKED FPL Cannot navigate locked flight plan This occurs when the pilot attempts to activate a stored flight plan that contains locked waypoint Remove locked waypoint from flight plan Update flight plan with current waypoint WPT ARRIVAL Arriving at waypoint boxx Arriving at waypoint boox where xxxx is the waypoint name STEEP TURN Steep turn ahead A steep turn is 15 seconds ahead Prepare to turn INSIDE ARSPC Inside airspace he aircraft is inside the airspace ARSPC AHEAD Airspace ahead less than 10 minutes Special use airspace is ahead
62. desired flight plan Press the ACTIVE Softkey The confirmation window is now displayed With OK highlighted press the ENT Key to activate the flight plan To cancel the flight plan activation turn the large FMS Knob to highlight CANCEL and press the ENT Key ACTIVATE A FLIGHT PLAN LEG 1 2 Press the FPL Key to display the Active Flight Plan Page MFD or the Active Flight Plan Window PFD Press the FMS Knob to activate the cursor not required on the PFD and turn the large FMS Knob to highlight the destination waypoint for the desired leg Or Use the Joystick to place the Quick Select Box on the destination waypoint for the desired leg Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Ps Navigation 3 Press the ACT LEG Softkey MFD only or press the MENU Key highlight Activate Leg and press the ENT Key A confirmation window is displayed with ACTIVATE highlighted 4 Press the ENT Key to activate the flight plan leg To cancel press the CLR Key or highlight CANCEL and press the ENT Key 5 Press the FMS Knob to remove the flashing cursor if required STOP NAVIGATING A FLIGHT PLAN 1 Press the FPL Key to display the Active Flight Plan Page 2 Press the MENU Key to display the Page Menu Window 3 Turn the large FMS Knob to highlight Delete Flight Plan and press the ENT Key With OK highlighted press the ENT Key to deactivate the flight
63. display Magnetic Field Variation Database Update At startup the system compares this version of the MV DB with that presently being used by the AHRS GRS If the system determines the MV DB needs to be updated a prompt is displayed on the Navigation Map Page as shown in the following figure GRS MV DB Update Available Update from 2005 to 2010 OK CANCEL GRS Magnetic Field Variation Database Update Prompt Loading the magnetic field variation database update With OK highlighted as shown in the previous figure press the ENT Key on the MFD A progress monitor is displayed as shown in the following figure Uploading GRS Mag Var Database STARTING UPLOAD 0 0 Uploading Database to GRS When the upload is complete the system is ready for use 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 95 saunjea4 aoueplony 2 Duruue d AEN Sd5 S24JV olpny uqax sia sjueuinasu jeuonippy 2 Wil Tuo2 NeN uoneiedo Jeuuouqy Sue v unuuy m ke GARMIN Appendix Ssjueuinijsu fila 59 oipny uadx U105 AEN S2dV AeN Sd5 Duruue d Blank Page 6 2 4 aoueplony puezey saunjea4 jeuonippy uoneiedo jeuuouqy suay unuuy x pu ddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 96 A GARMIN A Activate a flight plan 14 Active Channel 56 Active databas
64. ditional Features GARMIN Displaying Pathways 1 Press the PFD Softkey 2 Press the SYN VIS Softkey 3 If not already enabled press the SYN TERR Softkey 4 Press the PATHWAY Softkey 5 Press the BACK Softkey to return to the previous page Displaying Heading on the Horizon 1 Press the PFD Softkey 2 Press the SYN VIS Softkey 3 If not already enabled press the SYN TERR Softkey 4 Press the HRZN HDG Softkey 5 Press the BACK Softkey to return to the previous page Displaying Airport Signs 1 Press the PFD Softkey 2 Press the SYN VIS Softkey 3 If not already enabled press the SYN TERR Softkey 4 Press the APTSIGNS Softkey 5 Press the BACK Softkey to return to the previous page TERMINAL PROCEDURE CHARTS NOTE With the availability of SafeTaxi ChartView or FliteCharts it may be necessary to carry another source of charts on board the aircraft SafeTaxi SafeTaxi is an enhanced feature that gives greater map detail as the map range is adjusted in on the airport The airport display on the map reveals runways with numbers taxiways identifiers and airport landmarks including ramps buildings control towers and other prominent features Resolution is greater at lower map ranges The aircraft symbol provides situational awareness while taxiing Pressing the DCLTR Softkey declutter once removes the taxiway markings and airport identification labels Pressing the DCLTR Sof
65. e TAWS Not Available TANS Available will be heard when sufficient GPS signal is received TAWS TEST System Test pass TANS System Test OK 68 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Annunciations amp Alerts ALERT MESSAGE Alerts Window Message Audio Alert PFD FAN FAIL The cooling fan for the PFD is inoperative None MFD FAN FAIL The cooling fan for the MFD is inoperative None VOICE ALERTS Voice Alert Description Minimums minimums f The aircra t has descended below the preset barometric minimum descent altitude Vertical track f The aircra tis one minute from Top of Descent Issued only when vertical navigation is enabled Traffic Played when a Traffic Advisory TA is issued Traffic Not Available The aircraft is outside the Traffic Information Service TIS coverage area MFD amp PFD MESSAGE ADVISORIES Message Comments lost Recheck settings DATA LOST Pilot stored data was The pilot profile data was lost System reverts to default pilot profile and settings The pilot may reconfigure the MFD amp PFDs with preferred settings if desired XTALK ERROR A flight display crosstalk error has occurred The MFD and PFDs are not communicating with each other The G950 system should be serviced n PFD1 SERVI
66. e 93 Active Navigation Database 93 ADF 7 8 62 AHRS 77 78 Airport Signs 49 50 Airways 90 AOPA s Airport Directory 52 Audio panel controls NAV1 NAV2 8 Auxiliary video 54 Barometric Altitude Minimums 2 Barometric pressure 88 C CDI 1 8 81 Channel Presets 57 ChartView 50 51 Checklists 58 59 Clearance player 8 Clearance recorder 8 Code selection softkeys 7 COM 7 8 61 D DB Mismatch 91 94 DCLTR Softkey 50 Dead Reckoning 63 Dedutter 62 85 91 Delete a Waypoint 30 Direct to 13 14 19 DME 7 8 DR mode 63 64 190 01147 01 Rev A Index E Edit a flight plan 30 Electronic checklists 58 59 Emergency checklist 59 Enable Terrain 45 Enter an Airway 28 F Flight path marker 49 Flight plan import export messages 83 FliteCharts 50 51 Frequency Transfer 8 H Horizon heading 49 Inhibit 45 47 Inhibit TAWS 47 Inhibit Terrain 45 Inset Map 85 86 Intercom isolation 9 IOI 66 67 68 J Jeppesen 51 M Magnetic Field Variation Database Update 95 Map panning 40 Message advisories 69 82 METAR 39 Minimums 69 MKR MUTE 8 Mode 88 Mode selection softkeys 7 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T Index 1 sainjea4 aoueplony 2 buluueld AEN Sd5 S24JV oipny uddx sia sjuauimasu jeuonippy 2 wold Tuo2 NeN Yid uoneiedo Jeuuouqy Sue v unuuy 1221 ow Additional Hazard Flight Nav Com Flight Features Avoidance Procedures Plan
67. er must be turned off then on 72 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Annunciations amp Alerts DATABASE MESSAGE ADVISORIES CONT Message Comments DB MISMATCH Airport Terrain database mismatch The PFDs and MFD have different airport terrain database versions or regions installed Check the AUX SYSTEM STATUS Page to determine versions or regions Also check the AUX SYSTEM STATUS Page for a database synchronization function not completed After synchronization is complete power must be turned off then on NAV DB UPDATED Active navigation database updated System has updated the active navigation database from the standby navigation database GMA 1347 MESSAGE ADVISORIES Message Comments GMAT FAIL GMAT is inoperative GMA1 CONFIG GMAT config error Config service req d The audio panel self test has detected a failure The audio panel is unavailable The G950 system should be serviced The audio panel configuration settings do not match backup configuration memory The G950 system should be serviced MANIFEST GMAT software mismatch communication halted The audio panel has incorrect software installed The G950 system should be serviced GMA1 SERVICE GMAT needs Service Return unit for repair The audio panel self test has detected a problem Certain audio functio
68. es between AUTO and DEST DEST mode for the Navigation Information z display see the Flight Management section for more information x 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 89 Additional Hazard Flight Nav Com Hight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Abnormal Operation Annun Alerts Index Appendix Appendix A GARMIN Level 1 MAP 90 Level 2 TRAFFIC PROFILE TOPO TERRAIN AIRWAYS NEXRAD XM LING METAR LEGEND BACK Description Enables second level Navigation Map softkeys Displays traffic information on Navigation Map Displays removes Profile View on Navigation Map Page Displays topographical data e g coastlines terrain rivers lakes and elevation scale on Navigation Map Displays terrain information on Navigation Map Displays airways on the map cycles through the following AIRWAYS No airways are displayed AIRWY ON All airways are displayed AIRWY LO Only low altitude airways are displayed AIRWY HI Only high altitude airways are displayed Displays NEXRAD weather and coverage information on the Navigation Map if installed Displays XM lightning information on the Navigation Map if installed Displays METAR flags on airport symbols shown on the Navigation Map if installed Displays the legend for the selected weather products Available only when N
69. esented by the G950 can be misused or misinterpreted and therefore become unsafe WARNING To reduce the risk of unsafe operation carefully review and understand all aspects of the G950 Pilot s Guide documentation Thoroughly practice basic operation prior to actual use During flight operations carefully compare indications from the G950 to all available navigation sources including the information from other NAVAIDs visual sightings charts etc For safety purposes always resolve any discrepancies before continuing navigation Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A amp GARMIN _ ___ Waring Cautions k Notes WARNING The illustrations in this guide are only examples Never use the G950 to attempt to penetrate a thunderstorm Both the FAA Advisory Circular Subject Thunderstorms and the Aeronautical Information Manual AIM recommend avoiding by at least 20 miles any thunderstorm identified as severe or giving an intense radar echo WARNING Lamp s inside this product may contain mercury HG and must be recycled or disposed of according to local state or federal laws For more information refer to our website at www garmin com aboutGarmin environment disposal jsp WARNING Because of variation in the earth s magnetic field operating the system within the following areas could result in loss of reliable attitude and heading indications North of 72 North lati
70. ey again to accept the waypoint ENTER AN AIRWAY IN A FLIGHT PLAN 28 1 2 3 Press the FPL Key Press the FMS Knob to activate the cursor not required on the PFD and turn the large FMS Knob to highlight the waypoint after the desired airway entry point If this waypoint is not a valid airway entry point a valid entry point should be entered at this time Or Use the Joystick to place the Quick Select Box on the waypoint after the desired airway entry point If this waypoint is not a valid airway entry point a valid entry point should be entered at this time Turn the small FMS Knob one click clockwise and press the LD AIRWY Softkey not available if using the Joystick or press the MENU Key and select Load Airway The Select Airway Page is displayed The LD AIRWY Softkey or the Load Airway menu item is available only when an acceptable airway entry waypoint has been chosen the waypoint ahead of the cursor position Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Flight Planning 4 Turn the FMS Knob to select the desired airway from the list and press the ENT Key Low altitude airways are shown first in the list followed by all altitude airways and then high altitude airways 5 Turn the FMS Knob to select the desired airway exit point from the list and press the ENT Key LOAD is highlighted 6 Press the ENT Key The system returns to editing the fli
71. ference not match the published and is not designated to altitude in navigation be used in determining database or no published vertical flight path altitude exists guldance Small Text Altitude is not designated Altitude is designated The system cannot to be used in determining for use in giving vertical use this altitude in vertical flight path flight path guidance determining vertical guidance Altitude has Altitude has been flight path guidance been retrieved from the retrieved from the navigation database and 1 navigation database s provided as a reference or has been entered by the pilot and matches a published altitude in the navigation database 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sjuauimasu sub 59 oipny uadx 0105 AEN ACN 540 52 suelv uoneiedo sainjea4 aoueplony SoJnpa204d Duruue d unuuy Jeuuouqy Jeuonippy paezey nuru xipuaddy x pul GARMIN GPS Navigation Ssjueuinijsu fila 59 Tu102 AEN s24v 549 Buruuejd Blank Page 6 2 4 aoueplony puezey s m jeuonippy uoneiedo jeuuouqy suay unuuy x pu ddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 18 GARMI N Flight Planning FLIGHT PLANNING TRIP PLANNING 1 Tur the large FMS Knob to select the AUX page group 2 If necessar
72. ght plan with the new airway inserted INVERT AN ACTIVE FLIGHT PLAN 1 Press the FPL Key to display the active flight plan 2 Press the MENU Key to display the Page Menu 3 Turn the large FMS Knob to highlight Invert Flight Plan 4 Press the ENT Key The original flight plan remains intact in its flight plan catalog storage location 5 With OK highlighted press the ENT Key to invert the flight plan REMOVE A DEPARTURE ARRIVAL APPROACH OR AIRWAY FROM A FLIGHT PLAN Remove using the Quick Select Box active flight plan only 1 Press the FPL Key on the MFD to display the active flight plan 2 Use the Joystick to move the Quick Select Box around the desired procedure name or airway in the flight plan 3 Press the CLR Key to display a confirmation window 4 With OK highlighted press the ENT Key to remove the selected procedure or airway Remove using the cursor 1 Press the FPL Key to display the active flight plan Press the FMS Knob to activate the cursor Or for a stored flight plan a Press the FPL Key on the MFD b Turn the small FMS Knob to select the Flight Plan Catalog Page Press the FMS Knob to activate the cursor 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 29 oipny uddx 59 sjuauimasu U105 AEN 16114 52 2 G LL AEN Sd5 nubi eouepioAy paezey Suelv uoneiedo sainjea4 Tunuuy Jeuuouqy Jeuon
73. he Altimeter Barometric Pressure Setting 1 Selecting Standard Barometric Pressure 29 92 in Hg 1 Change Altimeter Barometric Pressure Setting 5 1 Change Navigation Sources ssssssseenennnnnnnnnns 1 Enable Disable OBS Mode While Navigating with GPS 2 GenericTimet aaa aaa pada qae acd ada gd qe i a 2 Set Barometric Minimum Descent Altitude sss 2 Displaying Wind Data 3 Changing HSI Format nennen 3 ENGINE INDICATION SYSTEM 5 NAV COM TRANSPONDER AUDIO PANEL 7 ADF Tuning If Installed 7 DME Tuning If Installed sene 7 Enter a Transponder Code sss 7 Selecting a COM Radio a R ri e TRE ua 7 Selecting a NAV 8 NAV COM Tuninj asas irte rem rem irt etn Pt n 8 Digital Clearance Recorder and Player 8 Intercom System ICS Isolation 9 AUTOMATIC FLIGHT CONTROL 5 1 S TEC Fifty Five X 1 GPS NAVIGATION aeter tet deseas aa datae ove 3 Direct to Navigation
74. he FMS Knob to select the desired emergency checklist and press the ENT Key 4 Press the ENT Key or CHECK Softkey to check the selected emergency checklist item The line item turns green and a checkmark is placed in the box next to it The next line item is automatically highlighted for checking Either FMS Knob can be used to scroll through the checklist and select the desired checklist item Press the CLR Key or UNCHECK Softkey to remove a check mark from an item 5 When all checklist items have been checked Checklist Finished is displayed in green text at the bottom left of the checklist window If all items in the checklist have not been checked CHECKLIST NOT FINISHED will be displayed in yellow text 6 Press the ENT Key GO TO NEXT CHECKLIST will be highlighted by the cursor 7 Press the ENT Key to advance to the next checklist 8 Press the RETURN Softkey to return to the previous checklist 9 Press the EXIT Softkey to exit the Checklist Page and return to the page last viewed 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 59 s mp o4d Buruuejd AeN 549 S24V olpny uqax sia siu u nnsul Tu102 AEN 3461 aoueplony paezey xipuaddy SH V uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy x pul GARMIN itional Features Add Sjueuinijsu fila 59 oipny uadx U105 AEN S2dV AeN Sd5 Duruue d r Blank Page 6 2
75. ight half of the display Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN SCHEDULER Scheduler messages appear in the Alerts Window on the PFD When a scheduler message is waiting the ALERTS Softkey label changes to ADVISORY Pressing the ADVISORY Softkey opens the Alerts Window and acknowledges the scheduler message The softkey label reverts to ALERTS when pressed the Alerts Window is removed from the display and the scheduler message is deleted from the message queue Message timers set to periodic alerting automatically reset to the original timer value once the message is displayed When power is cycled all messages are retained until deleted and message timer countdown is resumed Enter a Scheduler Message 1 2 3 4 5 6 7 8 9 Select the AUX Utility Page Press the FMS Knob momentarily to activate the flashing cursor Turn the large FMS Knob to highlight the first empty scheduler message naming field Use the FMS Knob to enter the message text to be displayed in the Alerts Window and press the ENT Key Press the ENT Key again or use the large FMS Knob to move the cursor to the field next to Type Turn the small FMS Knob to select the message alert type Event Message issued at the specified date time One time Message issued when the message timer reaches zero default setting e Periodic Message issued each time the mess
76. in G950 Cockpit Reference Guide for the Tecnam P2006T s m p q e ueproAy SoJnpa204d Duruue d AEN 540 S24V oipny uadx 913 sjueumasu puezey ubi UI05 AeN ubiu jeuonippy uoneiedo Jeuuouqy uc PEST x pul Hazard Flight Nav Com Hight Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Features Annunciations amp Alerts A GARMIN PFD MFD MFD Alert Type 1 TAWS B Page Aural Message 7 Pop Up Alert Annunciation Reduced Required TERRAIN CAUTION OopsTACLE Caution Obstacle Cau Obstacle Clearance or tion Obstacle Caution ROC OO ONUOENED o Obstacle Ahead Obstacle Ahead Imminent Obstacle TERRAIN OBSTACLE AHEAD Obstacle Ahead Obstacle Impact Caution 101 or Ahead OBSTACLE x Caution Obstacle Cau tion Obstacle Premature Descent TERRAIN TOO LOW TERRAIN Too Low Terrain Alert Caution PDA Altitude Callout None None Five Hundred 500 Excessive Descent TERRAIN SKRE Sink Rate Rate Caution EDR Negative Cimb TERRAIN varsa Don t sink Rate Caution NCR or or nu TAWS SYSTEM STATUS ANNUNCIATIONS Abnormal Operation Index Appendix PFD MFD TAWS B Page TAWS System Test Fail TAMS FAIL TAWS Alerting is disabled TAWS INH No GPS position or excessively TAWS N A degraded GPS signal System Test in progress Aural Message TANS System Failur
77. ippy xipuaddy x pul Nav Com XPDR Audio Abnormal Additional Hazard Annun Flight Instruments EIS AFCS Flight Procedures Planning GPS Nav Appendix Alerts Operation Features Avoidance Index Flight Planning 2 3 4 A GARMIN d Turn the large FMS Knob to highlight the desired flight plan e Press the EDIT Softkey Turn the large FMS Knob to highlight the title for the approach departure arrival or airway to be deleted Titles appear in white directly above the procedure s waypoints Press the CLR Key to display a confirmation window With OK highlighted press the ENT Key to remove the selected procedure or airway STORE A FLIGHT PLAN 1 2 3 After creating a flight plan on either the PFD or MFD it may be saved by pressing the MENU Key Turn the large FMS Knob to highlight Store Flight Plan and press the ENT Key With OK highlighted press the ENT Key to store the flight plan EDIT A STORED FLIGHT PLAN 1 2 3 4 5 6 7 Press the FPL Key on the MFD then tum the small FMS Knob to display the Flight Plan Catalog Page Press the FMS Knob to activate the cursor Turn the large FMS Knob to highlight the desired flight plan Press the EDIT Softkey Turn the large FMS Knob to place the cursor in the desired location Enter the changes then press the ENT Key Press the FMS Knob to return to the Flight Plan Catalog Page DELETE A WAYPOINT FROM
78. itude Terrain Obstacle between 100 and 1000 below current aircraft altitude Terrain Obstade is more than 1000 Black below aircraft altitude Enable Disable Aviation Data 1 While the Terrain SVS Page is displayed press the MENU Key 2 Turn the small FMS Knob to select Show or Hide Aviation Data 3 Press the ENT Key Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Materi Avaidanss Terrain SVS Inhibit Inhibit Terrain Alerting While the Terrain SVS Page is displayed press the INHIBIT Softkey Or 1 Press the MENU Key 2 Turn the small FMS Knob to select Inhibit Terrain 3 Press the ENT Key Enable Terrain Alerting While the Terrain SVS Page is displayed press the INHIBIT Softkey Or 1 While the Terrain SVS Page is displayed press the MENU Key 2 Turn the small FMS Knob to select Enable Terrain 3 Press the ENT Key A NOTE If Terrain SVS alerts are inhibited when the Final Approach Fix is the active waypoint in a GPS SBAS approach a LOWALT annunciation may appear on the PFD next to the altimeter if the current aircraft altitude is at least 164 feet below the prescribed altitude at the Final Approach Fix Displaying Terrain and Obstacles on the Navigation Map 1 With the Navigation Map displayed press the MAP Softkey 2 Press the TERRAIN Softkey Terrain and obstacle proximity will now be displayed on the map 3
79. key 2 Tum the large FMS to select the DME source field 3 Turn the small FMS Knob to select the desired Nav radio 4 Press the ENT Key to complete the selection ENTER A TRANSPONDER CODE 1 Press the XPDR Softkey to display the transponder mode selection softkeys 2 Press the CODE Softkey to display the transponder code selection softkeys for digit entry 3 Press the digit softkeys to enter the code in the code field When entering the code the next key in sequence must be pressed within 10 seconds or the entry is cancelled and restored to the previous code Five seconds after the fourth digit has been entered the transponder code becomes active SELECTING A COM RADIO Transmit Receive Press the COM1 MIC COM2 MIC or COM3 MIC Key optional COM if installed on the audio panel Receive Only Press the COM1 COM2 or COM3 Key optional COM if installed on the audio panel 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T Sjueumasu S24V oipny 4ddX sia JUI05 AEN Suelv uoneiado saunyea4 aoueplony saunpa20Jd Fuluueld AEN Sd5 unuuy jeuuouqy jeuonippy paezey xipuaddy x pul iui Wfi l4 Flight Instruments Nav Com XPDR Audio EIS Abnormal Additional Hazard Flight Planning Annun GPS Nav Appendix Alerts Operation Features Avoidance Procedures Index A Nav Com XPDR Audio Panel GARMIN SELECTING A NAV RADIO 1 To begin navigating using a navigation radi
80. kpit Reference Guide for the Tecnam P2006T A Wamings Santions amp Notes GARMIN NOTE All visual depictions contained within this document including screen images of the G950 panel and displays are subject to change and may not reflect the most current G950 system and aviation databases Depictions of equipment may differ slightly from the actual equipment NOTE This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE The data contained in the terrain and obstacle databases comes from government agencies Garmin accurately processes and cross validates the data but cannot guarantee the accuracy and completeness of the data NOTE This product its packaging and its components contain chemicals known to the State of California to cause cancer birth defects or reproductive harm This notice is being provided in accordance with California s Proposition 65 If you have any questions or would like additional information please refer to our web site at www garmin com prop65 NOTE Interference from GPS repeaters operating inside nearby hangars can cause an intermittent loss of attitude and heading displays while the aircraft is on the ground Moving the aircraft more than 100 yards
81. kpit Reference Guide for the Tecnam P2006T PFD MFD TERRAIN SVS Page Annunciation Terrain System Not Available Terrain System Available will be heard when sufficient GPS Signal is received one Terrain System Test OK 190 01147 01 Rev A A GARMIN Annunciations amp Alerts TAWS ALERTS PFD MFD MFD Alert Type 1 TAWS B Page Aural Message eii Pop Up Alert Annunciation Excessive Descent PULL UP Pull Up Rate Warning EDR Reduced Required PULL UP Terrain Terrain Pull Up Terrain Clearance or Pull Up Warning RTC or Terrain Ahead Pull Up Terrain Ahead Pull Up Imminent Terrain PULL UP Terrain Ahead Pull Up Ter Impact Warning ITI or rain Ahead Pull Up rz Terrain Terrain Pull Up Pull Up Reduced Required PULL UP Obstacle Obstacle Pull Obstacle Clearance or Up Pull Up tena Oe 3 Obstacle Ahead Pull Up Obstacle Ahead Pull Up Imminent Obstade PULL UP Obstacle Ahead Pull Up Impact Warning or Obstacle Ahead Pull Up 0 Obstacle Obstacle Pull Up Pull Up Reduced Required TERRAIN CAUTION TERRAIN Caution Terrain Caution Terrain Clearance or Terrain utente 5 i Terrain Ahead Terrain Ahead Imminent Terrain TERRAIN TERRAIN AFAD Terrain Ahead Terrain Impact Caution ITI or Ahead TERRAIN 9 d Caution Terrain Caution Terrain 190 01147 01 Rev A 67 Garm
82. lects Mode C Altitude Reporting Mode transponder replies to identification and altitude interrogations GND Manually selects Ground Mode the transponder does not allow Mode A and Mode C replies but it does permit acquisition squitter and replies to discretely addressed Mode S interrogations VFR Automatically enters the VFR code 1200 in the U S A only 88 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Level 1 Level 2 Level 3 Description 2 CODE Displays transponder code selection 5 softkeys 0 7 7 Use numbers to enter code 53 BKSP Removes numbers entered one at a time IDENT Activates the Special Position Identification SPI pulse for 18 seconds identifying the transponder return on the ATC screen oipny uadx 0105 AEN TMR REF Displays Timer References Window gt NRST Displays Nearest Airports Window K ALERTS Displays Alerts Window A MFD SOFTKEY MAP Duruue d Juil Lao EL 1 1 Es A ES 5 z E 2 Select the BACK Softkey on gt this level to return to the top 5 softkey level 5 if installed if installed if installed if installed E PROFILE TOPO TERRAIN AIRWAYS NEXRAD XMLTNG BACK n V D v3 V3 D 5 92 os ze a MFD Softkeys 5 Sg Level 1 Level 2 Level3 Description aS AUTO or Switch
83. light if the G950 detects an invalid GPS solution or is unable to calculate a GPS position the system automatically reverts to Dead Reckoning DR Mode In DR Mode the G950 uses its last known position combined with continuously updated airspeed and heading data when available to calculate and display the aircrafts current estimated position NOTE Dead Reckoning Mode only functions in Enroute ENR or Oceanic OCN phase of flight In all other phases an invalid GPS solution produces a NO GPS POSITION annunciation on the map and the G950 stops navigating in GPS Mode DRModeisindicated on the G950 by the appearance of the letters DR superimposed in yellow over the own aircraft symbol as shown in the following figure In addition DR is prominently displayed also in yellow on the HSI slightly above and to the right of the aircraft symbol on the CDI as shown in the following figure Also the CDI deviation bar is removed from the display Lastly but at the same time a GPS NAV LOST alert message appears on the PFD Normal navigation using GPS SBAS source data resumes automatically once a valid GPS solution is restored It is important to note that estimated navigation data supplied by the G950 in DR Mode may become increasingly unreliable and must not be used as a sole means of navigation If while in DR Mode airspeed and or heading data is also lost or not available the DR function may not be capable of estimating your
84. ludes the following Navigation Status Box fields except Active Leg TAS and DTK GPS Bearing Pointer Wind data and pointers in the Wind Data Box on the PFD Current Track Indicator All Bearing Pointer Distances Active Flight Plan distances bearings and ETE values The accuracy of all nearest information airports airspaces and waypoints is questionable Also airspace alerts continue to function but with degraded accuracy Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Amunciations amp Alerts ANNUNCIATIONS amp ALERTS WARNING ANNUNCIATION Annunciation Text Alerts Window Message Audio Alert Lh Overvoltage Rh Overvoltage Lh Low Coolant Rh Low Coolant Right engine fire detected Left engine fire detected Main door open Rear Door Open Repeating Tone CAUTION ANNUNCIATION Annunciation Text Alerts Window Message Audio Alert Lh Generator Rh Generator Aircraft using external power Pitot Heat Fail Gear Pump Powered Single Chime SAFE OPERATING ANNUNCIATION Annunciation Text Alerts Window Message Audio Alert Lh Fuel Pump Rh Fuel Pump Pitot Heat 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sainjea4 2 Duruue d AEN Sd5 241V oipny uddx 93 5349 0115 2 nubi uio AeN
85. m card slot of the specified PFD or MFD The SD card needs to be reinserted PFD1 or MFD1 CARD 1 ERR Card 1 is invalid The SD card in PFD or MFD contains invalid data the top card slot of the specified PFD1 or MFD1 CARD 2 ERR Card 2 is invalid The SD card in specified PFD o the bottom card slot of the MFD contains invalid data 82 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Annunciations 8 Alerts FLIGHT PLAN IMPORT EXPORT MESSAGES In some circumstances some messages may appear in conjunction with others Flight Plan Import Export Results Flight plan successfully imported File contained user waypoints only User waypoints imported successfully No stored flight plan data was modified Description A flight plan file stored on the SD card was successfully imported as a stored flight pla The file stored on the SD card did not contain a flight plan only user waypoints These waypoints have been saved to the system user waypoints No flight plans stored in the system have been modified n No flight plan files found to import The SD card contains no flight plan data Flight plan import failed Flight plan data was not successfully imported from the SD card Flight plan partially imported f Some flight plan waypoints were success imported from the SD card
86. n Press the transfer Switch again to cycle its operation If the problem persists the G950 system should be serviced LOI GPS integrity lost Crosscheck with other NAVS GPS integrity is insufficient for the current phase of flight 190 01147 01 Rev A 75 Garmin 6950 Cockpit Reference Guide for the 2006 so1njeoJ 2 Buruuejg AEN Sd S24V oipny uadx sia s u un sul paezey nubi u102 AEN nubi jeuonippy uoneiedo Jeuuouqy m x pul Hazard Flight Nav Com Fight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix Annunciations amp Alerts G GIA 63W MESSAGE ADVISORIES CONT A ARMIN Message GPS NAV LOST Loss of GPS navigation Insufficient satellites Comments Loss of GPS navigation due to in satellites sufficient GPS NAV LOST Loss of GPS navigation Position error Loss of GPS navigation due to position error GPS NAV LOST Loss of GPS navigation GPS fail Loss of GPS navigation due to GPS failure ABORT APR Loss of GPS navigation Abort approach Abort approach due to loss of GPS navigation APR DWNGRADE Approach downgraded Vertical guidance generated by SBAS is unavailable use LNAV only minimums Change HDG reference to TRUE GPS1 SERVICE GPS1 needs ser
87. nation airport departure arrival or approach Press the SHW CHRT Softkey The appropriate chart is displayed if available for the item selected Press the GO BACK Softkey to return to the previous page Change Day Night View 1 2 3 4 5 6 7 While viewing a chart press the MENU Key to display the Page Menu OPTIONS Turn the large FMS Knob to highlight the Chart Setup Menu Option and press the ENT Key Turn the large FMS Knob to move between the FULL SCREEN and COLOR SCHEME Options Turn the small FMS Knob to choose between the On and Off Full Screen Options Turn the small FMS Knob to choose between Day Auto and Night Options In Auto Mode turn the large FMS Knob to select the percentage field and change percentage with the small FMS Knob The percentage of change is the day night crossover point based on backlighting intensity Press the FMS Knob when finished to remove the Chart Setup Menu AOPA AIRPORT DIRECTORY IF INSTALLED AOPA Airport Directory adds enhanced airport information when viewing airports on the WPT Airport Information Page This database is updated four times per year Check fly garmin com for the current database View Airport Directory Information 52 While viewing the WPT Airport Information Page if necessary press the INFO 1 Softkey to change the softkey label to display INFO 2 AOPA airport information is displayed on the r
88. ning GPS Nav AFCS XPDR Audio EIS Instruments Abnormal Operation Annun Alerts bed Appendix Index Multi Function Display MFD Softkeys 89 N NAV 8 NAV1 1 8 NAV2 1 8 Navigation database 16 17 70 72 73 79 80 83 93 94 95 NEXRAD 39 86 90 0 085 2 Obstacles 72 73 74 P Pathvvays 49 50 Povver up page 58 Profile View 45 47 90 Q Quick Select Box 14 16 28 29 30 35 36 R Reversionary mode 61 ROC 66 67 68 S SafeTaxi 50 SBAS 37 45 47 63 74 76 Secure Digital SD card 58 Standby Navigation Database 94 S TEC Fifty Five X Autopilot 11 Store Flight Plan 30 SVS 49 Index 2 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T A GARMIN SVS Terrain 49 Synchronization 92 SYNC Status 94 Synthetic Vision System 49 T TA 69 TAF 39 TAS 77 TAWS 46 47 66 67 68 Terrain 43 44 46 72 86 90 Terrain SVS 44 45 Timer 79 Topographical data 86 90 Traffic 39 42 86 90 Traffic Advisory 69 Traffic map page 42 43 45 47 Transponder 7 88 89 V Vertical speed guidance 17 Vertical track 69 Video 54 VNV 13 62 81 W Waypoint Selection Submenu 26 Weather data link page 39 Wind data 3 87 X XM lightning 86 90 XM weather 39 Z Zoom Range 55 190 01147 01 Rev A A GARMIN m 2345 Turner Road SERIES Salem OR 97302 U 5 A p 503 391 3411 f 503 364 21 y Ty r a Garmin Europe Ltd Liber
89. ns may still be available and the audio panel may still be usable The G950 system Should be serviced when possible GIA 63W MESSAGE ADVISORIES Message Comments GIA1 CONFIG G A1 config error Config service req d GIA2 CONFIG GIA2 config error Config service req d The GIA1 and or GIA2 configuration settings do not match backup configuration memory The G950 system should be serviced 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T n So1nje2J aoueplony s mp oold Buruue d AEN Sd5 2 oipny uddx 913 siu umnnsu paezey nubi Juo ney Wil euonippv uoneiedo Jeuuouqy 5 4 x pul Hazard Flight Nav Com Fight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix 5 Annunciations amp Alerts A GARMIN GIA 63W MESSAGE ADVISORIES CONT GIA1 CONFIG GIA1 audio confi error Config service req d Message G A2 CONFIG GIA2 audio confi error Config service req d W Comments The GIA1 and or GIA2 have an error in the audio configuration The G950 system should be serviced too low GIA1 COOLING GIA1 temperature too low GIA2 COOLING GIA2 temperature The GIA1 and or GIA2 temperature is too low to operate correctly Allow units to warm up to operating temperature temperature temper
90. nstalled autopilot S TEC FIFTY FIVE X AUTOPILOT A NOTE This section covers only the additional FD status annunciations that may appear in the G950 AFCS Status Box These status annunciations are not analogous to both the G950 and the S TEC Fifty Five X Refer to the approved S TEC Fifty Five X Pilot s Operating Handbook POH for comprehensive list of annunciations and operating instructions Inadditiontothe redundant status mode annunciations and or visual representations that are simultaneously displayed on both the G950 AFCS Status Box and or PFD and the S TEC Fifty Five X Autopilot Display and or Remote Annunciator Display the G950 displays the additional status mode annunciation of FD when the Flight Director Mode is engaged 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sia sjuounasu oipny uadx 0105 AEN ARN Sd5 52 SH lV uoneiedo sainjea4 aoueplony 2 Duruue d junuuy Jeuuouqy Jeuonippy paezey xipuaddy x pul iui Wfl GARMIN AFCS Sjueuinijsu fila 593 oipny uadx U105 AEN 52 AeN 5492 4 r Blank Page 6 2 4 aoueplony puezey saunjea4 jeuonippy uoneiedo jeuuouqy suay unuuy x pu ddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 12 A GARMIN GPS Navigation GPS NAVIGATION DIRECT TO NAVIGATION Direct to Navigati
91. o press the CDI Softkey on the PFD to select VORT LOC1 NAV1 or VOR2 LOC2 NAV2 2 Press the NAV1 NAV2 DME or ADF Key on the audio panel to select or deselect the navigation radio audio source All radio keys can be selected individually or together NAV COM TUNING 1 Press the small tuning knob to select the desired radio for tuning A light blue box highlights the radio frequency to be tuned 2 Turn the respective tuning knobs to enter the desired frequency into the standby frequency field The large knob enters MHz and the small knob enters kHz 3 Press the Frequency Transfer Key to place the frequency into the active frequency field DIGITAL CLEARANCE RECORDER AND PLAYER NOTE Only the audio for the selected COM MIC Key is recorded Audio is not recorded for COM3 MIC Pressing the PLAY Key once plays the latest recorded memory block then returns to normal operation Pressing the MKR MUTE Key while playing a memory block stops play Pressing the PLAY Key during play begins playing the previously recorded memory block Each subsequent press of the PLAY Key begins playing the next previously recorded block Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN INTERCOM SYSTEM ICS ISOLATION Press the PILOT and or COPLT Key on the audio panel to select those isolated from hearing the Nav Com radios and music PILOT KEY COPLT KEY Pilot Hears Passenger Hears Annun
92. o settings 1 With the AUX VIDEO Page displayed press the SETUP Softkey 2 Press the BRIGHT or BRIGHT to adjust display brightness in five percent increments from 0 to 10096 3 Press the CNTRST or CNTRST to adjust display contrast in five percent increments from 0 to 10096 4 Press the SAT or SAT to adjust display saturation in five percent increments from O to 10096 5 If desired return the display to the default settings by pressing the RESET Softkey 6 Press the BACK Softkey to return to the previous softkey level Display Selection Pressing the HIDE MAP Softkey removes the map and displays video on the full screen The softkey label changes to grey with black characters Pressing the HIDE MAP Softkey again restores the map view and the small video image The softkey label returns to white characters on a black background Zoom Range Pressing the VID ZM 4 or VID ZM Softkeys increases or decreases video display magnification between 1x and 10x The RANGE Knob can be used to increase or decrease the range setting on the map display or zoom in and out on the video display While in the Split Screen mode pressing the MAP ACTV or VID ACTV Softkey determines which display the RANGE Knob adjusts Pressing the softkey to display MAP ACTV allows the RANGE Knob to control the range setting of the map display Pressing the softkey to display VID ACTV allows the RANGE Knob to control the zoom setting of the
93. ockpit Reference Guide for the Tecnam P2006T sjuauimasu nubi 53 oipny uddx UI0JNeN ACN 540 52 suelv uoneiedo sainjea4 aoueplony SoJnpa204d Duruue d unuuy Jeuuouqy Jeuonippy paezey n xipuaddy x pul Flight Instruments Nav Com XPDR Audio Flight Planning Abnormal Additional Hazard Avoidance Annun EIS GPS Nav AFCS Procedures Appendix Alerts Operation Features Index GPS Navigation 7 8 9 10 11 12 13 14 15 A GARMIN Turn the small FMS Knob to enter the desired altitude Press the ENT Key If the waypoint entered is an airport the option to select MSL or AGL is now displayed If the waypoint is not an airport proceed to step 10 Turn the small FMS Knob to select MSL or AGL Press the ENT Key The cursor is placed in the OFFSET distance field Turn the small FMS Knob to enter the desired target altitude offset from the selected Direct to Press the ENT Key to highlight Activate or turn the large FMS Knob to highlight the CRS field Turn the small FMS Knob to enter the desired course to the waypoint Press the ENT Key to highlight ACTIVATE Press the ENT again to activate the Direct to ACTIVATE A STORED FLIGHT PLAN 1 2 3 4 5 Press the FPL Key on the MFD and turn the small FMS Knob to display the Flight Plan Catalog Page Press the FMS Knob to activate the cursor Turn the large FMS Knob to highlight the
94. oint in the flight plan list Or Use the Joystick to move Insertion Point Indicator to the location for the new waypoint in the flight plan list and press the FMS Knob 3 Turn the small FMS Knob one dick dockwise The Waypoint Information Window is now displayed 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 21 s q s u u nnsul U105 AEN 3461 olpny uqax 52 aoueplony paezey Suelv uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Additional Hazard Avoidance Abnormal Annun Flight Instruments EIS AFCS Flight Procedures Planning GPS Nav Appendix Alerts Operation Features Index Flight Planning 4 A GARMIN Enter the new flight plan waypoint by one of the following a Enter the user waypoint identifier facility or city b Press the ENT Key Or a Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed b Turn the small FMS Knob to the right to display the NRST airport waypoints to the aircraft s current position c Turn the large FMS Knob to select the desired waypoint d Press the ENT Key Or a Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed b Turn the small FMS Knob to the right to display the RECENT waypoints c Turn the large FMS Knob to select the desired waypoint d Press the ENT Key e Press the ENT K
95. on from the MFD 1 Press the Direct to E Key 2 Enter the waypoint identifier 3 Press the ENT Key to confirm the identifier The Activate field is highlighted 4 If no altitude constraint or course is desired press the ENT Key to activate To enter an altitude constraint proceed to step 5 5 Turn the large FMS Knob to place the cursor over the VNV altitude field 6 Enter the desired altitude 7 Press the ENT Key If the waypoint entered is an airport the option to select MSL or AGL is now displayed If the waypoint is not an airport proceed to step 9 8 Tum the small FMS Knob to select MSL or AGE 9 Press the ENT Key The cursor is now flashing in the VNV offset distance field 10 Enter the desired offset distance before the waypoint 11 Press the ENT Key The Activate field is highlighted 12 Press the ENT Key to activate Direct to Navigation from the PFD 1 Press the Direct to Key 2 Tum the large FMS Knob to place the cursor in the desired selection field 3 Turn the small FMS Knob to begin selecting the desired identifier location etc 4 Press the ENT Key 5 The cursor is now flashing on ACTIVATE If no altitude constraint or course is desired press the ENT Key to activate To enter an altitude constraint proceed to step 6 6 Turn the large FMS Knob to place the cursor over the ALT altitude field 190 01147 01 Rev A Garmin G950 C
96. one display but an error occurs on another the error message will be displayed with the affected displays listed after it VVhen an error message is displayed the problem must be corrected before synchronization can be completed A power cycle is required to restart synchronization when Card Full or Err is shown 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T SaJnjeaJ aoueplony SoJnpa20Jd Duruue d AEN Sd5 S24JV oipny uddx sia sjuauimasu jeuonippy 2 Wil JUI0 NEN 1i uoneiedo Jeuuouqy Sue v unuuy k Additional Hazard Flight Nav Com Hight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Abnormal Operation Annun Alerts Index Appendix A Appendix _ GARMIN Error Message Description Canceled Database synchronization has been canceled by removing the bottom SD card in display being updated Card Full SD card does not contain sufficient memory Err Displayed for all other errors that may cause the synchronization process to be halted Timeout System timed out prior to the database transfer completing Loading Garmin Database Updates 1 2 3 4 5 6 7 8 9 10 11 12 92 With system power OFF remove the MFD database card from the bottom card slot of the MFD Update the Garmin databases on the MFD card Insert the MFD database card into the bottom card slot of
97. ow showing the selected leg is displayed With ACTIVATE highlighted press the ENT Key Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Procedures Activate Arrival using the cursor 1 Press the FPL Key on the MFD to display the active flight plan 2 Press the FMS Knob to activate the cursor 3 Turn the large FMS Knob to highlight the desired waypoint within the arrival 4 Press the ACT LEG Softkey A confirmation window showing the selected leg is displayed 5 With ACTIVATE highlighted press the ENT Key LOAD AND OR ACTIVATE AN APPROACH PROCEDURE NOTE If certain GPS parameters SBAS RAIM etc are not available some published approach procedures for the desired airport may not be displayed in the list of available approaches 1 Press the PROC Key 2 Tum the large F MS Knob to highlight SELECT APPROACH 3 Press the ENT Key A list of available approaches for the destination airport is displayed 4 Turn either FMS Knob to highlight the desired approach 5 Press the ENT Key A list of available transitions for the selected approach procedure is now displayed 6 Turn either FMS Knob to select the desired transition The Vectors option assumes vectors will be received to the final course segment of the approach and will provide navigation guidance relative to the final approach course 7 Press the ENT Key The cursor moves to
98. r consequential damages that result from the use or inability to use the software or re documentation even if AOPA or an AOPA authorized representative has been advised of the possibility of such damages User agrees not to sue AOPA and to the maximum extent allowed by aw to release and hold harmless AOPA from any causes of action claims or losses re ated ated to any actual or alleged inaccuracies in the information Some jurisdictions do not allow the lim S o itation or exclusion of implied warranties or liability for incidental or consequential dam the above limitations or exclusions may not apply to you ages December 2011 190 01147 01 Rev A Printed in the U S A amp GARMIN Warnings Cautions 5 Notes V ARNING Navigation and terrain separation must NOT be predicated upon the use of the terrain avoidance feature The terrain avoidance feature is NOT intended to be used as a primary reference for terrain avoidance and does not relieve the pilot from the responsibility of being aware of surroundings during flight The terrain avoidance feature is only to be used as an aid for terrain avoidance Terrain data is obtained from third party sources Garmin is not able to independently verify the accuracy of the terrain data WARNING The displayed minimum safe altitudes MSAs are only advisory in nature and should not be relied upon as the sole source of obstacle and terrain a
99. r applicable charts Current aircraft position is not displayed on FliteCharts The FliteCharts database contains procedure charts for the United States only This database is updated on a 28 day cycle If not updated within 180 days of the expiration date FliteCharts will no longer function View Charts from the Navigation Map Page 1 Press the SHW CHRT Softkey when displayed Or Move the map pointer to point to a desired point on the map and press the SHW CHRT Softkey 2 Select the DP STAR APR WX and NOTAM softkeys to access charts for departures arrivals approaches weather and NOTAMs Note that NOTAMS are only available with ChartView 3 Press the GO BACK Softkey to return to the previous page 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T s mp o4d Buruuejd AeN 549 S24V olpny uqax sia siu u nnsul yudu Tu102 AEN UTE eouepioAy paezey s n ze 4 jeuonippy xipuaddy suelv uoneiedo junuuy Jeuuouqy x pul Flight Instruments Nav Com XPDR Audio Flight Planning Hazard Avoidance Additional Features Abnormal Annun EIS AFCS GPS Nav Procedures Appendix Alerts Operation Index A Additional Features amp GARMIN View Charts from the Active Flight Plan Page 1 2 3 4 While viewing the Active Flight Plan Page press the FMS Knob to activate the cursor Turn the large FMS Knob to select the departure airport desti
100. ration date on the povver up screen and the effective date on the AUX System Status Page being displayed in yellow A NOTE After the navigation database is loaded or copied the top SD card may be removed 1 With the system OFF insert the SD card containing the new navigation database version into the top card slot of the display PFD1 PFD2 or MFD to be updated label of SD card facing left 2 Turn the system ON A prompt is displayed in the upper left corner of the display 3 Pressthe NO Softkey to proceed to loading the active database 4 Aprompt similar to the following is displayed Press the YES Softkey to update the active navigation database 5 After the update completes the display starts in normal mode 6 Turn the system OFF and remove the SD card from the top card slot 7 Repeat steps 1 through 6 for the other displays PFD1 PFD2 or MFD 8 Apply power to the system and press the ENT Key to acknowledge the startup Screen 9 Turn the large FMS Knob to select the AUX Page group on the MFD 10 11 w Turn the small FMS Knob to select the System Status Page Press the Display Database Selection Softkey to show active navigation database information for each display MFD1 DB PFD1 DB PFD2 DB Verify the correct active navigation database cycle information is shown for each display 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 93 SaJnjeoJ eo
101. return to 5 the top level softkeys Er ES gt 2 za o Inset Map Softkeys PE os Dp Level 1 Level 2 Level 3 Description e o c INSET Displays Inset Map in PFD lower left corner 88 Sa OFF Removes Inset Map DCLTR 3 Selects desired amount of map detail Sue v unuuy cycles through declutter levels DCLTR No Declutter All map features visible DCLTR 1 Declutters land data DCLTR 2 Declutters land and SUA data DCLTR 3 Removes everything except the active flight plan gt 5 z 2 x x pul 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 85 Flight Instruments Annun Abnormal Additional Hazard Flight Nav Com Appendix Alerts Operation Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Index Appendix A GARMIN Level 1 Level 2 Level 3 Description VVX LGND TRAFFIC TOPO TERRAIN NEXRAD XM LING METAR Displays icon and age on the Inset Map for the selected vveather products if installed Displays traffic information on Inset Map Displays topographical data e g coastlines terrain rivers lakes and elevation scale on Inset Map Displays terrain information on Inset Map Displays NEXRAD weather and coverage information on the Inset Map if installed Displays XM lightning information on the Inset Map if installed Displays METAR flags on airport symbols shown on the Inset Map if installe
102. rsor 4 Tur the large FMS Knob to the place the cursor in the USER WAYPOINT LIST field 5 Turn the small FMS Knob to highlight the desired waypoint 6 Press the DELETE Softkey 7 Themessage Would you like to delete the user waypoint is displayed With YES highlighted press the ENT Key 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 25 52 2 4 AEN 540 nubi aoueplony paezey suelv uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Additional Hazard Avoidance Abnormal Annun Flight Instruments EIS AFCS Flight Procedures Planning GPS Nav Appendix Alerts Operation Features Index Flight Planning A GARMIN CREATE A FLIGHT PLAN 26 NOTE When creating a flight plan in the Active Flight Plan Window the first leg is activated automatically after it is created Creating an active flight plan 1 2 3 4 5 6 Press the FPL Key Press the FMS Knob to activate the cursor only on MFD Turn the small FMS Knob to display the Waypoint Information Window Turning it clockwise displays a blank Waypoint Information Window turning it counter clockwise displays the Waypoint Information Window with a waypoint selection submenu allowing selection of active flight plan nearest recent user or airway waypoints Enter the identifier facility or city name
103. sible AHRS1 GPS AHRS1 not receiving any GPS information The 1 AHRS is not receiving any or any useful GPS information Check AFMS limitations The G950 system should be serviced 190 01147 01 Rev A 7 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T So1nje24 s mp oold Buruue d AEN Sd5 2 oipny uddx 913 sjueumasu paezey nubi jeuonippy uoneiedo Jeuuouqy i EST x pul Hazard Flight Nav Com Flight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix d Annunciations amp Alerts A GARMIN GRS 77 MESSAGE ADVISORIES CONT Message Comments AHRS1 GPS AHRS1 not receiving backup GPS information The 1 AHRS is not receiving backup GPS information The G950 system should be serviced AHRS1 GPS AHRS1 operating exdusively in no GPS mode AHRS1 SRVC AHRS1 Magnetic field model needs update The 1 AHRS is operating exclusively in no GPS mode The G950 system should be serviced The 1 AHRS earth magnetic field model is out of date Update magnetic field model when practical GEO LIMITS AHRS1 too far North South no magnetic compass The aircraft is outside geographical limits for approved AHRS operation Heading is flagged as invalid MANIFEST GRS1 software mismatch communication halted The
104. splays the HSI in an arc format Cycles the Bearing 2 Information Window through NAV2 or GPS waypoint identifier and GPS derived distance information Displays softkeys for setting the altimeter and BARO settings to metric units When enabled displays altimeter in meters Press to display the BARO setting as inches of mercury Press to display the BARO setting as hectopacals 87 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sainjea4 aoueplony 2 Duruue d AEN Sd5 S24JV olpny uqax sia sjuauimasu jeuonippy puezey ni Tuo2 NeN nubi uoneiedo Jeuuouqy Sue v unuuy hz Flight Instruments Annun Abnormal Additional Hazard Flight Nav Com Appendix Alerts Operation Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Index A Appendix GARMIN Level 1 Level2 Level 3 Description STD BARO Sets barometric pressure to 29 92 in Hg 1013 hPa IG installed n n onn o mn n n n E E Press the BACK Softkey to return to the top level softkeys ETT IE 7 Tor Esse Sex JR NNN NNN NN HHH A Press the BACK Softkey to return to the previous level softkeys Transponder Softkeys Levell Level2 Level 3 Description XPDR Displays transponder mode selection softkeys STBY Selects Standby Mode transponder does not reply to any interrogations ON Selects Mode A transponder replies to interrogations ALT Se
105. ss the FMS Knob to activate the cursor 4 Turn the large FMS Knob to highlight the desired flight plan 5 Press the INVERT Softkey Invert and activate stored flight plan is displayed 6 With OK highlighted press the ENT Key The selected flight plan is now inverted and activated The original flight plan remains intact in its flight plan catalog storage location 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T oipny uddx 59 sjuaumasu U105 AEN 3463 52 2 4 AEN 540 nubi eouepioAy paezey spay uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Abnormal Additional Hazard Annun Flight Instruments EIS AFCS Flight Procedures Planning GPS Nav Appendix Alerts Operation Features Avoidance Index Flight Planning A GARMIN COPY A FLIGHT PLAN 1 2 3 4 5 6 Press the FPL Key on the MFD Turn the small FMS Knob to select the Flight Plan Catalog Page Press the FMS Knob to activate the cursor Turn the large FMS Knob to highlight the flight plan to be copied Press the COPY Softkey A Copy to flight plan 6 confirmation window is displayed With OK highlighted press the ENT Key to copy the flight plan To cancel turn the large FMS Knob to highlight CANCEL and press the ENT Key DELETE A FLIGHT PLAN 1 2 3 4 5 6 Press the FPL Key on
106. t to highlight TEMPORARY b Press the ENT Key to place a check mark in the box Turn the large FMS Knob to place the cursor back in the WAYPOINT TYPE field 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sia sjueuinsu U05 AEN 3 olpny uqax 52 paezey suelv uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Additional Hazard Avoidance Abnormal Annun Flight Instruments EIS AFCS Flight Procedures Planning GPS Nav Appendix Alerts Operation Features Index Flight Planning 22 A GARMIN 7 With the cursor in the WAYPOINT TYPE field turn the small FMS Knob to display a list of waypoint types Turn the small FMS Knob to select RAD RAD radial radial Press the ENT Key The cursor moves to the REFERENCE WAYPOINTS field With the first waypoint name highlighted use the FMS Knobs to enter the desired waypoint name Waypoints may also be selected as follows 8 9 10 11 a b o Or a b o d Or a b d Or a b o d When a flight plan is active turning the small FMS Knob to the left will display a list of the flight plan waypoints Turn the large FMS Knob to select the desired waypoint Press the ENT Key Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed Turn the small FMS
107. the MFD Turn the small FMS Knob to select the Flight Plan Catalog Page Press the FMS Knob to activate the cursor Turn the large FMS Knob to highlight the flight plan to be deleted Press the DELETE Softkey A Delete flight plan 22 confirmation window is displayed With OK highlighted press the ENT Key to delete the flight plan To cancel turn the large FMS Knob to highlight CANCEL and press the ENT Key GRAPHICAL FLIGHT PLAN CREATION 32 1 2 3 4 5 Press the FPL Key to display the Active Flight Plan Page on the MFD Use the Joystick to move the Insertion Point Indicator to the desired waypoint entry point in the flight plan list Press the Joystick to activate the map pointer Use the Joystick to move the pointer to the desired point on the map to be inserted as a waypoint in the flight plan Select the LD WPT Softkey The selected waypoint is inserted at the selected point The default user waypoint naming is USR000 USR001 USR002 and so on To change the user waypoint name follow the procedure for modifying a user waypoint Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Flight Planning EXPORT A FLIGHT PLAN TO AN SD CARD NOTE See the Annunciations amp Alerts section for flight plan export message descriptions 1 Insert the SD card into the top card slot on the MFD 2 Press the FPL Key to display the Active Flight Plan Page on the M
108. the MINIMUMS field sjuauimasu nubi 59 oipny uddx UI0JNeN 52 AEN 540 buluueld Wil s mp old eouepioAy 2 SoJnjeaJ jeuonippy uoneiedo Jeuuouqy 8 If desired the DA MDA for the selected approach procedure may be entered and displayed on the PFD Turn the small FMS Knob in the direction of the green arrow to change the display from OFF to BARO 9 Press the ENT Key The cursor moves to the altitude field Turn the small FMS Knob to enter the published DA MDA for the selected approach procedure 10 Press the ENT Key LOAD or ACTIVATE is now displayed with LOAD highlighted 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 3 Sue v unuuy xipuaddy x pul Nav Com XPDR Audio Procedures Abnormal Additional Hazard Annun Flight Instruments Flight Planning EIS AFCS GPS Nav Appendix Alerts Operation Features Avoidance Index Procedures GARMIN 11 Turn the large FMS Knob to select either LOAD or ACTIVATE Selecting LOAD enters the selected approach procedure into the active flight plan but is not currently active Selecting ACTIVATE enters the selected approach procedure into the active flight plan and activates the first leg of the approach 12 Press the ENT Key ACTIVATE AN APPROACH IN THE ACTIVE FLIGHT PLAN 1 2 3 Press the PROC Key Turn the large FMS Knob to highlight ACT
109. tkey twice removes VOR station 90 Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Additional Features ID the VOR symbol and intersection names if within the airport plan view Pressing the DCLTR Softkey a third time removes the airport runway layout unless the airport in view is part of an active route structure Pressing the DCLTR Softkey again cycles back to the original map detail The SafeTaxi database contains detailed airport diagrams for selected airports These diagrams provide the pilot with situational awareness by displaying the aircraft position in relation to taxiways ramps runways terminals and services This information should not be used by the pilot as the basis for maneuvering the aircraft on the ground This database is updated on a 56 day cycle ChartView If Installed ChartView resembles the paper version of Jeppesen terminal procedures charts The charts are displayed in full color with high resolution The MFD depiction shows the aircraft position on the moving map in the plan view of most approach charts and on airport diagrams The ChartView database is updated on a 14 day cycle If the ChartView database is not updated within 70 days of the expiration date ChartView will no longer function FliteCharts If Installed FliteCharts resemble the paper version of AeroNav Services terminal procedures charts The charts are displayed with high resolution and in color fo
110. tude at all longitudes South of 70 South latitude at all longitudes North of 65 North latitude between longitude 75 W and 120 W Northern Canada North of 70 North latitude between longitude 70 W and 128 W Northern Canada North of 70 North latitude between longitude 85 E and 114 E Northern Russia South of 55 South latitude between longitude 120 E and 165 E Region south of Australia and New Zealand WARNING Do not use GPS to navigate to any active waypoint identified as a NON WGS84 WPT by a system message NON WGS84 WPT waypoints are derived from an unknown map reference datum that may be incompatible with the map reference datum used by GPS known as WGS84 and may be positioned in error as displayed CAUTION The PFD and MFD displays use a lens coated with a special anti reflective coating that is very sensitive to skin oils waxes and abrasive cleaners CLEANERS CONTAINING AMMONIA WILL HARM THE ANTI REFLECTIVE COATING It is very important to clean the lens using a clean lint free cloth and an eyeglass lens cleaner that is specified as safe for anti reflective coatings CAUTION The Garmin G950 does not contain any user serviceable parts Repairs should only be made by an authorized Garmin service center Unauthorized repairs or modifications could void both the warranty and the pilot s authority to operate this device under FAA FCC regulations 190 01147 01 Rev A Garmin G950 Coc
111. ty House Bulls Copse Road Hounsdovvn Business Park Southampton 5040 9RB U K p 4408708501241 f 44 0870 8501251 2010 2011 Garmin Ltd or its subsidiaries 100 01147 01 Rev A
112. udio Additional Hazard Avoidance Abnormal Annun Flight Instruments EIS AFCS Flight Procedures Planning GPS Nav Appendix Alerts Operation Features Index Flight Planning GARMI N Or a Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed b Turn the small FMS Knob to the right to display the NRST airports to the aircraft s current position Turn the large FMS Knob to select the desired waypoint d Press the ENT Key Or a Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed b Turn the small FMS Knob to the right to display the RECENT waypoints Turn the large FMS Knob to select the desired waypoint d Press the ENT Key Or a Turn the small FMS Knob to the left Initially a flight plan waypoint list is displayed b Turn the small FMS Knob to the right to display the USER waypoints Turn the large FMS Knob to select the desired waypoint d Press the ENT Key 11 Press the ENT Key The cursor is displayed in the RAD radial field Enter the desired radial from the reference waypoint 12 Press the ENT Key 13 The cursor is now displayed in the DIS distance field Enter the desired distance from the reference waypoint 14 Press the ENT Key 15 Press the FMS Knob to remove the flashing cursor 24 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A G
113. uepioAy SoJnpa204d Duruue d AEN Sd5 S24JV olpny uqax sia sjuauimasu jeuonippy 2 wold Tuo2 NeN nubi uoneiedo Jeuuouqy Sue v unuuy bea Additional Hazard Flight Nav Com Flight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Abnormal Operation Annun Alerts Index Appendix A Appendix GARMIN Loading the Jeppesen Navigation Database as the Standby Navigation Database The purpose of the Standby Navigation Database is to allow the loading of the next cycle of the Jeppesen Navigation Database to the bottom SD card prior to its effective date The Jeppesen Navigation Database is available from Jeppesen seven days prior to its effective date 1 2 3 4 5 6 1 8 9 NOTE After the navigation database is loaded or copied the top SD card may be removed With the system OFF insert the SD card containing the new navigation database version into the top card slot of the MFD Verify that an SD card is inserted in the bottom slot of each PFD and the MFD Turn the system ON A prompt is displayed Press the YES Softkey The navigation database is copied to the SD card in the bottom card slot of the MFD After the navigation database files are copied to the bottom SD card press any key to continue as instructed Again press any key to continue as instructed on the display Press the NO Softkey The display now starts in normal mode Sin
114. ul 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T GARMIN Flight Instruments I x oipny uadx U105 AEN s24v AeN Sd5 buluueld r Blank Page 6 2 4 aoueplony puezey saunjea4 jeuonippy uoneiedo jeuuouqy suay unuuy x pu ddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T GARMIN ____Engine indication System ENGINE INDICATION SYSTEM NOTE The G950 Engine Indication System EIS is not available in the Tecnam P2006T Refer to the Pilot s Operating Handbook POH for engine display information and operating limitations 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T sjuauimasu nubi sual uonesado s n e 4 aoueplony s mp oold Buruue d AEN 540 2 oipny uddx junuuy Jeuuouqy jeuonippy paezey xipuaddy x pul GARMIN Engine Indication System Sjueuinijsu sub U105 AEN s24v AeN Sd5 buluueld Blank Page 6 2 4 aoueplony puezey saunjea4 jeuonippy uoneiedo jeuuouqy suay unuuy x pu ddy x pul 190 01147 01 Rev A Garmin 6950 Cockpit Reference Guide for the Tecnam P2006T A GARMIN Nav Com XPDR Audio Panel NAV COM TRANSPONDER AUDIO PANEL ADF TUNING IF INSTALLED Tune the ADF using the remote ADF control head DME TUNING IF INSTALLED 1 Press the DME Soft
115. urn to the top level softkeys SoJnpa20Jd Duruue d AEN Sd5 Wil eouepioAy paezey CHANGE NAVIGATION SOURCES 1 Press the CDI Softkey to change from GPS to VOR1 or LOC1 This places the light blue tuning box over the NAV1 standby frequency in the upper left corner of the PFD 2 Press the CDI Softkey again to change from VOR1 or LOC1 to VOR2 or LOC2 This places the light blue tuning box over the NAV2 standby frequency 3 Press the CDI Softkey a third time to return to GPS suelv uoneiedo sainjea4 unuuy Jeuuouqy Jeuonippy xipuaddy x pul 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T Nav Com XPDR Audio Abnormal Additional Hazard Flight Planning Annun AFCS GPS Nav Appendix Alerts Operation Features Avoidance Procedures Index Flight Instruments A GARMIN ENABLE DISABLE OBS MODE WHILE NAVIGATING WITH GPS 1 2 3 Press the OBS Softkey to select OBS Mode Turn a CRS Knob to select the desired course to from the waypoint Press a CRS Knob to synchronize the Selected Course with the bearing to the next waypoint Press the OBS Softkey again to disable OBS Mode GENERIC TIMER 1 2 3 Press the TMR REF Softkey then turn the large FMS Knob to select the time field hh mm ss Turn the FMS Knobs to set the desired time then press the ENT Key The UP DOWN field is now highlighted Turn the small FMS Knob to display the UP DOVVN window Turn the FMS
116. uuy Jeuuouqy Jeuonippy xipuaddy x pul Nav Com XPDR Audio Additional Hazard Avoidance Abnormal Annun Flight Instruments EIS AFCS Flight Procedures Planning GPS Nav Appendix Alerts Operation Features Index Flight Planning 20 5 6 7 8 9 10 11 12 13 A GARMIN d Turn the small FMS Knob to select the desired leg of the flight plan or select CUM to apply trip planning calculations to the entire flight plan Selecting FPL 00 displays the active flight plan If an active flight plan is selected REM is an available option to display planning data for the remainder of the flight plan NOTE The page mode must be set to MANUAL to perform the following steps Turn the large FMS Knob to highlight the departure time DEP TIME field NOTE The departure time on the Trip Planning Page is used for preflight planning Refer to the Utility Page for the actual flight departure time Enter the departure time Press the ENT Key when finished Departure time may be entered in local or UTC time depending upon system settings The flashing cursor moves to the ground speed GS field Enter the ground speed Press the ENT Key when finished Note that in automatic page mode ground speed is provided by the system The flashing cursor moves to the fuel flow field Enter the fuel flow Press the ENT Key when finished Note that in
117. uxiliary Video If Installed 5 SiriusXM Radio Entertainment If Installed 56 Electronic Checklists If 58 ABNORMAL OPERATION 61 Reversionary Mode eiie mati em dai iri 61 Abnormal COM Operation sssssssssseeeennennnnnn 61 Hazard Displays with Loss of GPS Position 61 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A GARMIN Tale of Contents Unusual Attitudes 62 Dead ReckOning tmi eem te e e rm t 000 63 ANNUNCIATIONS amp ALERTS 65 WARNING Annunciation CAUTION Annunciation sene Safe Operating 65 Terrain SVS Alerts Terrain SVS System Status Annunciations sssse 66 TAWS Alerts eo enn n Ode de m e d e edd Gee TAWS System Status Annunciations Alert Message et t i tid Voic Alerts De ree btt td e ovo db d a vna erst MFD amp PFD Message Advisories MFD amp PFD Message Advisories Database Message Advisories GMA 1347 Message Advisories GIA 63W Message 150 15 GTX 33 Message Advisories
118. vice Return unit for repair TRUE APR True north approach GPS2 SERVICE GPS2 needs service Return unit Displayed after passing the first waypoint of a true north approach when the nav angle is set to AUTO A failure has been detected in th GPS2 receiver The receiver may The G950 system should be serv e GPS1 and or still be available iced NAV1 SERVICE service Return unit for repair a NAV2 SERVICE NAV2 needs service Return unit al ri A failure has been detected in th NAV2 receiver The receiver may The G950 system should be serv iced e NAV1 and or still be available NAV1 RMT XFR NAV1 remote transfer key is stuck NAV2 RMT XFR NAV2 remote transfer key is stuck The stuck in the enabled emote NAV1 and or NAV2 transfer switch is or pressed state Press the transfer switch again to cycle its operation If the problem persists the G950 system should be serviced 6 51 FAIL G S1 is inoperative G S2 FAIL G S2 is inoperative A failure has been detected in gl ideslope receiver 1 and or receiver 2 The G950 system should be serviced 76 Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 190 01147 01 Rev A A GARMIN Annunciations 8 Alerts GIA 63W MESSAGE ADVISORIES CONT Message Return unit for repair G
119. video display 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 55 sual uonesado s n e 4 aoueplony s mp oold Buruue d AEN Sd5 2 444 sia sjueumasu unuuy jeuuouqy jeuonippy paezey uii 0105 AEN ubi xipueddy x pul Flight Instruments Nav Com XPDR Audio Flight Planning Hazard Additional Features Abnormal Annun EIS AFCS GPS Nav Procedures Avoidance Appendix Alerts Operation Index Additional Features A GARMIN SIRIUSXM RADIO ENTERTAINMENT IF INSTALLED 56 The XM Radio Page provides information and control of the audio entertainment features of the SiriusXM Satellite Radio Selecting the XM Radio Page 1 2 3 Turn the large FMS Knob to select the Auxiliary Page Group Turn the small FMS Knob to select XM Radio Select the RADIO Softkey to show the XM Radio Page where audio entertainment is controlled Active Channel and Channel List The Active Channel Box on the XM Radio Page displays the currently selected channel The Channels List Box of the XM Radio Page shows a list of the available channels for the selected category Selecting a Category The Category Box of the XM Radio Page displays the currently selected category of audio 1 2 3 Select the CATGRY Softkey on the XM Radio Page Select the CAT and CAT softkeys to cycle through the categories Or Turn the small FMS Knob to display the
120. voidance information Always refer to current aeronautical charts for appropriate minimum clearance altitudes WARNING The altitude calculated by G950 GPS receivers is geometric height above Mean Sea Level and could vary significantly from the altitude displayed by pressure altimeters such as the GDC 74A Air Data Computer or other altimeters in the aircraft GPS altitude should never be used for vertical navigation Always use pressure altitude displayed by the G950 PFD or other pressure altimeters in aircraft WARNING Do not use outdated database information Databases used in the G950 system must be updated regularly in order to ensure that the information remains current Pilots using any outdated database do so entirely at their own risk WARNING Do not use basemap land and water data information for primary navigation Basemap data is intended only to supplement other approved navigation data sources and should be considered as an aid to enhance situational awareness WARNING Traffic information shown on the G950 Multi Function Display is provided as an aid in visually acquiring traffic Pilots must maneuver the aircraft based only upon ATC guidance or positive visual acquisition of conflicting traffic 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T A Wamings Cam one amp Notes GARMIN ee WARNING Do not use data link weather products e g XM WX S
121. waypoint is locked Comments Upon power up the G950 system detects that a stored flight plan waypoint is locked This occurs when an navigation database update eliminates an obsolete waypoint The flight plan cannot find the specified waypoint and flags this message This can also occur with user waypoints in a flight plan that is deleted Remove the waypoint from the flight plan if it no longer exists in any database Or update the waypoint name identifier to reflect the new information FPL WPT MOVE Flight plan waypoint moved The system has detected that a waypoint coordinate has changed due to a new navigation database update Verify that stored flight plans contain correct waypoint locations TIMER EXPIRD Timer has expired The system notifies the pilot that the timer has expired 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T 19 So1nje2J e uepioAy s mp oold Buruue d AEN Sd5 2 oipny uddx 913 Sjueumasu paezey nubi nubi jeuonippy uoneiedo Jeuuouqy EY x pul Hazard Flight Nav Com Flight Features Avoidance Procedures Planning GPS Nav AFCS XPDR Audio EIS Instruments Additional Abnormal Operation Index Appendix Annunciations amp Alerts A GARMIN MISCELLANEOUS MESSAGE ADVISORIES CONT Message DB CHANGE Database changed Verify user modified procedures Comments This occurs when a store
122. y turn the small FMS Knob to select the Trip Planning Page 3 The current page mode is displayed at the top of the page AUTOMATIC or MANUAL To change the PAGE MODE press the AUTO or MANUAL Softkey 4 For Direct to planning a Press the WPTS Softkey and verify that the starting waypoint field indicates P POS present position b If necessary press the MENU Key and select Set WPT to Present Position to display P POS Press the ENT Key and the flashing cursor moves to the ending waypoint field d Enter the identifier of the ending waypoint and press the ENT Key to accept the waypoint Or For point to point planning a Enter the identifier of the starting waypoint b Once the waypoint s identifier is entered press the ENT Key to accept the waypoint The flashing cursor moves to the ending waypoint Again enter the identifier of the ending waypoint d Press the ENT Key to accept the waypoint Or For flight plan leg planning a Press the FPL Softkey at the bottom of the display b Turn the small FMS Knob to select the desired flight plan already stored in memory by number Turn the large FMS Knob to highlight the LEG field 190 01147 01 Rev A Garmin G950 Cockpit Reference Guide for the Tecnam P2006T oipny uddx s q sjuauimasu U10 AEN 3463 52 2 4 AEN 540 nubi eouepioAy paezey suelv uoneiedo s n e 4 un

Download Pdf Manuals

Related Search

Related Contents

Tripp Lite NB1007GY User's Manual    Trane RTHD User's Manual  KOHLER K-2229-0 Installation Guide  User Manual MS198E - Physik Instrumente    TP-Link TL-WN722N Declaration of Conformity  Récepteur audio/vidéoAVR 7000  WSD-700 Betriebsanleitung (deutsch)  Marquette Responder  

Copyright © All rights reserved. Failed to retrieve file