Garmin MapSource User's manual and Installation Guide
Contents
1. 6 RESTRICTED RIGHTS If this Product is acquired by or for the U S Government then it is provided with Restricted Rights Use duplication or dis closure by the U S Government is subject to restrictions as set forth in subparagraphs c 1 ii of The Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 or subparagraphs c 1 and 2 of the Commercial Computer Software Restricted Rights at 48 CFR 52 227 19 or clause 18 52 227 86 d of the NASA Supplement to the FAR as applicable The contractor manufacturer is Garmin International Inc 1200 E 151st Street Olathe KS 66062 USA 7 EXPORT CONTROLS You agree not to export or re export the Product to any country in violation of the export control laws of the United States of America 8 GENERAL This License is the entire agreement between us superseding any other agreement or discussions oral or written and may not be changed except by a signed agreement This License shall be governed by and construed in accordance with the laws of the State of Kansas United States of America If any provision of this License is declared by a court of competent jurisdiction to be invalid illegal or unenforceable such a provision shall be severed from the License and the other provisions shall remain in full force and effect iii Introduction Features Garmin Data Cards The USB Data Card Programm2. USB Data Card Programmer user s manual and installation guide Copyright 2001 2002 Garmin Ltd or its subsidiaries Garmin International Inc 1200 E 151 Street Olathe Kansas 66062 U S A Tel 913 397 8200 or 800 800 1020 Fax 913 397 8282 Garmin Europe Ltd Unit 5 The Quadrangle Abbey Park Industrial Estate Romsey S051 9DL U K Tel 44 1794 519944 Fax 44 1794 519222 Garmin Corporation No 68 Jangshu 2 4 Road Shijr Taipei County Taiwan Tel 886 2 2642 9199 Fax 886 2 2642 9099 All rights reserved Except as expressly provided herein no part of this manual may be reproduced copied transmitted dissemi nated downloaded or stored in any storage medium for any purpose without prior written consent of Garmin Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed for personal use provided that such electronic or printed copy of this manual contains the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual is strictly prohibited Information in this manual is subject to change without notice Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes Visit the Garmin web site www garmin com for current updates and supplemental information concerning the use and
3. or network This copy is to be used by only a single user at a time If you wish to use the Product for more users you will need an additional license for each user b make one copy of the Product for archival or backup purposes c use a copy of the Product on a home or portable computer if that copy is never loaded at the same time it is loaded on your primary computer d transfer the Product to someone else only if you assign all of your rights under this License cease all use of the Product erase or destroy any copy including the hard disk copy made in support of your use of the Product and ensure that the other person agrees to the terms of this License 3 YOU MUST NOT a make copies of the Product except as expressly permitted in Section 2 of this License b translate reverse engineer decompile or disassemble the Product except to the extent the foregoing restriction is expressly prohibited by applicable law c rent lease loan sub license distribute assign or transfer the Product except as set out in Section 2 d above d modify the Product or merge all or any part of the Product with another program Introduction Software License Agreement 4 TERM This License shall continue for as long as you use the Product However this License will terminate automatically without notice from Garmin if you fail to comply with any of its terms or conditions You must agree upon terminations to destroy all
4. time to read through this users manual in order to fully under stand all of the operating procedures This manual is organized into three sections The Introduction section provides licensing agreement informa tion and a description of the programmer soi Pp prog Minimum System Requirements IBM Compatible PC with Pentium processor 16 The Installation section introduces you to basic features and procedures for programmer setup Megabytes RAM CD ROM drive Mouse or other The Trouble Shooting section contains information for finding pointing device 256 color display adapter 24 bit solutions to installation and operating problems color recommended and monitor with 640 x 480 resolution or higher and up to 20 Megabytes free hard drive space A 32 bit operating system such Standard Package Contents USB Data Card Programmer as Windows 98 ME Windows 2000 or Windows USB Data Card Programmer XP Universal Serial Bus port USB The USB Data CD ROM with USB Device Drivers for Windows 98 ME Card Programmer is not designed to operate with 2000 and Garmin MapSource Upgrade Software including Windows 95 or Windows NT USB Support The USB drivers are also on the MapSource Software Requirements City Navigator CD ROM or MapSource Setup CD ROM if Existing installation of Garmin MapSource applicable upgraded to Version 3 04 or later e Users Manual e MapSource Users Manual Addendum for the USB Data Card Programm
5. ck on System then the Device Man ager tab then click the by Universal serial bus controller You should see Garmin USB Data Card Programmer on the list Another method would be to open the MapSource program click the Save To Device icon then the USB Port tab You should see Card Programmer listed in the Save Maps To window If the installation is still not successful try shutting the computer off for 1 minute then trying the alternate steps again A red X over the Programmer icon in Device Manager normally indicates a defec tive Programmer If the USB Programmer still will not install please contact Garmin Product Support for further assistance Installation Installing the Device Drivers Windows XP Users During installation of the USB Data Card Programmer you will see a message stating The following device has not passed the Windows Logo testing to verify its compatibility with Windows XP Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Garmin engineers have fully tested this prod uct and it is compatible with Windows XP Press the Continue Anyways button to finish the installation If you are running an early versi
6. copies of the Product The Limitations of War ranties and Liability set out below shall continue in force even after any termination 5 LIMITATION OF WARRANTIES AND LIABILITY THE PRODUCT IS PROVIDED ON AN AS IS BASIS WITHOUT ANY WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABLE QUALITY MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR THOSE ARISING BY LAW STATUTE USAGE OR TRADE OR COURSE OF DEALING THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE PRODUCT IS ASSUMED BY YOU NEITHER WE NOR OUR DEALERS OR SUPPLIERS SHALL HAVE ANY LIABILITY TO YOU OR ANY OTHER PERSON OR ENTITY FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO LOSS OF REVENUE OR PROFIT LOST OR DAMAGED DATA OR OTHER COM MERCIAL OR ECONOMIC LOSS EVEN IF WE HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE WE ARE ALSO NOT RESPONSIBLE FOR CLAIMS BY A THIRD PARTY OUR MAXIMUM AGGREGATE LIABILITY SHALL NOT EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT THE LIMITATIONS IN THIS SECTION SHALL APPLY WHETHER OR NOT THE ALLEGED BREACH OR DEFAULT IS A BREACH OF FUNDAMENTAL CONDITION OR TERM OF A FUNDAMENTAL BREACH SOME STATES COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU T T
7. d then Control Panel Double click on the Add New Hardware Installation Programmer Cable USB Universal Serial Bus Port and USB Connector icon 4 The next screen will ask you if you want it to search for the best driver for your device or if you want to display a list to choose from Select Search for the best driver for your device and click on Next 5 The next screen will display a list of locations to search for the new Use care to insert the USB connector correctly Do not drivers Select CD ROM Drive from the list and click on Next force the connection as this may damage the USB port Make certain all other boxes remain unchecked on your computer or the USB connector on the Pro grammer 6 The Wizard will search for the driver and then display a window to tell you it is ready to install Click on Next You may see a Copying Files screen which tells you the file cannot be found Choose Root Directory of the CD ROM drive if not already there and to try copying again example d Click OK to continue 7 When installation is complete a window will display that shows the device name Garmin USB Data Card Programmer and states Installation the driver installation is finished Click on Finish 8 A final window will appear telling you that operating software for the Card Programmer is being installed Installing the Device Drivers 9 To make sure the USB Progra
8. directly away from the Programmer using the extractor handle on the Data Card amp Use care not to remove the Data Card from the Program mer until data transfer has been completed to avoid pos sible loss of data Disconnecting the Programmer from Your Computer After the USB Data Card Programmer has been successfully installed hardware and software disconnecting and reconnecting the Programmer can performed without additional installation steps 1 Before disconnecting the Programmer be certain that no data transfer is in progress 2 Unplug the USB connector from your computer You do not need to turn the computer off before removing or inserting the USB connector Installation Installing a Data Card in the Programmer Extractor Handle Disconnecting the Programmer from Your Computer Trouble Shooting Symptom Trouble Shooting Guide Probable Cause Remedy Windows does not recognize that the Programmer has been connected to the computer USB Connector is not properly inserted into the USB port on the computer USB Port on your computer is not prop erly configured Be certain the Programmer has been properly connected to your computer Consult your computer supplier When preparing to transfer data a No compatible device available message appears When preparing to transfer data a There is no data card in the Programmer mes sage appears System operati
9. er Introduction Software License Agreement THIS SOFTWARE IS OWNED BY GARMIN CORPORATION GARMIN AND IS PROTECTED UNDER COPYRIGHT LAWS A D INTERNATIONAL COPYRIGHT TREATIES THIS SOFTWARE IS LICENSED NOT SOLD THIS SOFTWARE IS PROVIDED UNDER THE FOLLOWING LICENSE WHICH DEFINES WHAT YOU MAY DO WITH THE PRODUCT AND CONTAINS LIMITATIONS ON WARRANTIES AND OR IMPORTANT CAREFULLY READ THIS LICENSE BEFORE USING THIS PRODUCT INSTALLING COPYING OR OTHERWIS UCT INDICATES YOUR ACKNOWLEDGMENT THAT YOU HAVE READ THIS LICENSE AND AGREE TO ITS TERMS IF YOU RETURN THE COMPLETE PRODUCT TO Garmin INTERNATIONAL INC CUSTOMER SERVICE 1200 EAST 151st STREET WITHIN 10 DAYS OF THE DATE YOU ACQUIRED IT FOR A FULL REFUND 1 LICENSE Garmin we or us provides you with storage media containing computer software the Program which may a tographic data and on line or electronic documentation and printed materials together called the Product and grants you a REMEDIES E USING THIS PROD DO NOT AGREE OLATHE KS 66062 so include digital car imited non exclusive license to use the Product in accordance with the terms of this license agreement The copyright and all other rights to the Product shall remain with us You must reproduce any copyright or other notice marked on the Product on all copies you make 2 YOU MAY a install and use one copy of the Product on a single computer
10. er utilizes Garmin Data Cards Available in five sizes 8 MB Data Card 16 MB Data Card 32 MB Data Card 64 MB Data Card 128 MB Data Card Check the Garmin web site or see your Garmin dealer for availability of these data cards USB Connector 6 Ft USB Data Cable Mini Data Card Programmer Data Card Slot accepts only Garmin Data Cards Data Card Programmer Installation of the USB Programmer and Device Drivers 1 Insert either the USB Data Card Programmer CD ROM MapSource City Navigator CD ROM or MapSource Setup CD into your computer s CD ROM drive It is important you insert the CD before you plug the USB Programmer into the PC If the MapSource program is open close the program Connecting the Programmer and 2 Connect the USB connector on the end of the Programmer cable Installing the Device Drivers to the USB port on the back of the computer Most computers have two USB Ports Either port should work The computer does not need to be turned off when connecting or disconnecting the USB Connector Programmer After connecting the Programmer to your computer fl you will need to install the device drivers from the CD ROM AR 3 The computer will recognize the Programmer as a USB or unknown device and open the Add New Hardware Wizard and search for the device drivers Click on Next If for some reason the Wizard does USB Port not run automatically click the Start button and select Settings an
11. mmer has been successfully installed From the Control Panel click on System then the Device Manager tab then click the by Universal serial bus control ler You should see Garmin USB Data Card Programmer on the list Another method would be to open the MapSource program click the Save To Device icon then the USB Port tab You should see Card Programmer listed in the Save Maps To window If you see a yellow mark in front of the device name install appears at the end of the Programmer name or the Programmer appears under Other Devices as an unknown device follow these The required driver files which the USB Data Card Programmer needs to find on either the USB Data alternate steps to install the Programmer Card Programmer CD the City Navigator CD or the 1 Double click the My Computer icon from your Desktop For Win MapSource Setup CD are dows 98 click View Folder Options then the View tab grmn0200 inf For Windows 2000 ME click Tools Folder Options then the grmn0200 sys View tab grmn1200 sys s If these files cannot be seen in the root directory on the 2 Make note of the fo lowing changes if you wish to change your CD using Windows Explorer your View settings may View settings back after installing the Programmer Change the need to be adjusted Hidden Files selection to Show All Files or Show hidden files and folder
12. ng software is not USB compatible Programmer is not connected to USB port Card Programmer drivers are not installed No Data Card has been inserted in the Programmer The Data Card is not fully inserted into the Programmer Be certain the computer is operating on Windows 98 ME 2000 software Reconnect the USB Connector to the computer Install drivers Insert a Data Card into the Programmer Push the Data Card fully into the slot in the Programmer When properly inserted the card will protrude approximately 1 2 inch from the slot An unrecognized data card is in the programmer message appears when you attempt to transfer data The Data Card in the Programmer is damaged MapSource must be updated to be compatible with the card Insert a different card and try again Update MapSource software from the Garmin web site Ahy GARMIN Copyright 2001 2002 Garmin Ltd or its subsidiaries Garmin International Inc 1200 East 151 Street Olathe Kansas 66062 U S A Garmin Europe Ltd Unit 5 The Quadrangle Abbey Park Industrial Estate Romsey SO51 9DL U K Garmin Corporation No 68 Jangshu 2 Road Shijr Tai pei County Taiwan www garmin com Part Number 190 00201 00 Rev C
13. on of MapSource prior to 3 04 you may upgrade your version of MapSource at this time using the Installation driver CD provided with the USB Data Card Programmer If you already have a version of MapSource newer than 3 05 City Navigator or the MapSource Setup CD upgrading from the Installing the MapSource driver CD is not necessary You may also visit the Garmin web site to Software Upgrade download the most recent upgrade for MapSource To Install the MapSource Software Upgrade including USB Data Card Programmer Support 1 Insert the USB Data Card Programmer CD ROM into your comput er s CD ROM drive 2 Click the Start button and select Run 3 Then type in the drive letter of your CD ROM drive followed by the MapSource Update file name MSUPDATE EXE For example d msupdate exe 4 Press ENTER and follow on screen instructions 5 Open MapSource and check the About box in the help file to determine that you have successfully installed Version 3 04 or later To Install a Garmin Data Card 1 Insert the Data Card Label up and pin connector end first into the card slot in the Programmer standard USB Programmer pictured to the right For the Mini USB Programmer make sure the Garmin globe logo on the Programmer is facing UP for proper orientation 2 Be certain to install the Data Card completely into the slot to be sure the pin connections have been made 3 To remove the Data Card pull
14. operation of this and other Garmin products Garmin and StreetPilot are registered trademarks MapSource is a trademark of Garmin Ltd or its subsidiaries and may not be used without the express permission of Garmin Windows 95 Windows NT Windows 98 Windows ME Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation December 2002 Part Number 190 00201 00 Rev C Printed in Taiwan FCC Compliance FCC Compliance This device complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE home or office interference requirements are more stringent than outdoor requirements Operation of this device is subject to the following conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The USB Data Card Programmer does not contain any user serviceable parts Repairs should only be made by an authorized Garmin service center Unauthorized repairs or modifications could result in permanent damage to the equipment and void your warranty and your authority to operate this device under Part 15 regulations Introduction Thank you for choosing the Garmin USB Data Card Programmer or the Garmin StreetPilot III with Mini USB Data Card Programmer To get successful results from your new USB Data Card Programmer About This Manual take
15. s and uncheck the Hide file extensions for known file types or Hide protected operating system files then click OK 3 Be sure the driver CD is inserted and the USB Programmer is plugged into the PC Open the Control Panel For Windows 98 click on System then the Device Manager tab For Windows 2 2000 ME click the Hardware tab then click Device Manager 4 Find and highlight the incorrect Programmer entry on the Device Manager list click on Remove then click OK to confirm 5 Click Refresh then click Next to begin searching for the driv ers On the next screen let Windows search by leaving the bullet on the Search for best driver option and click Next On the next screen check ONLY the CD ROM drive option and click Next 6 The Wizard will search for the driver and then display a window to tell you it is ready to install Click on Next You may see a Copying Files screen which tells you the file cannot be found Choose Root Directory of the CD ROM drive if not already there and to try copying again example d Click OK to continue 7 When installation is complete a window should display that shows the device name Garmin USB Data Card Programmer and states the driver installation is finished Click on Finish 8 To make sure the USB Programmer has been successfully installed From the Control Panel cli
Download Pdf Manuals
Related Search