Fujitsu M5000-CL10-PI01 User's Manual
Contents
1. XSB Partitions can be configured to form a domain using any combination of XSBs XSBs divided with Uni XSB and Quad XSB can be mixed together within one domain The XSCF is used to configure a partition and specify the PSB division type Up to 4 partitions are supported A minimum of one system hard disk drive per partition is necessary as a boot device PSB Division Types Uni XSB The motherboard is divided into two physical system boards PSB Each PSB represents an own logical system in UNI XSB format The entire motherboard cannot be used as a single PSB Uni XSB is equivalent to the PSB definition for PRIMEPOWER 1 Division Type Uni XSB aa Ge VO Board additional The two PSBs are not divided and used as two logical system boards SB CPU chips memory PCI slots hard disk drives assigned to XSB are predetermined Mount as a minimum one CPU module and two MEM modules per operating XSB Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 19 38 If only one partition is configured with both PSBs in Uni XSB mode but no CPU and MEM modules are mounted on PSB 1 then HDDs and PCI slots on the additional I O board cannot be used Areas shaded black in the figure below are not equipped with CPU and MEM modules Motherboard VO Board base Gibi Ehe l CPU Module 2 CPU HS HO CPU 7 gt iO fH Product Facts Issue June 01 2008 Product SPARC E2. e Oneach used SB a minimum of one CPU Module and two Memory Boards are necessary The optional second O Board also requires the minimum of CPU and Memory on SB 1 Logical diagram of memory locations 1 O Board base Slots for HDD 0 CPU Modul 0 HDD 1 CPU Chip 0 sowan anwan az waw CPU DVD ROM Chip 1 aman senan DAT E Gigabit Ethernet sowan aowan arnan az waw CPU Chip 2 CPU Modul 1 CPU Chip 3 ELAM az waw a m TES E S 2 O Group 1 O Board optional Slots for HDD 2 HDD 3 CPU Chip 4 so naw arnan se nan ae nan CPU Modul 2 mory Board 5 CPU Me z m Chip 5 gt azman assan ao nan arnan CPU Chip 6 ao naw arnan az naw as nan PCI Express CPU Modul 3 PCI Express PCI Express CPU Chip 7 J O gt ao nan arnan Lgc waw as nan Group A Group B Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 28 38 Mounting Conditions for Memory with different sizes Condition 1 To mix different DIMM types on a certain SB see chapter Mounting additional Memory with different sizes Condition 2 Two sets of memory modules with the same size 16 DIMMs must be mounted When adding memory two sets of memory modules with the same size must be added at the same time Condition 3 W
3. Socket strip 1x 10 jacks IEC320 C13 10A 926361 F2262 E40 E Socket strip 1x 10 jacks IEC320 C13 10A 926361 F2262 E41 N combination Wi e O auf 1 x plug NEMA L6 30 For US CAN a plug 26361 F2262 L41 Socket strip 1 x 10 jacks IEC320 C13 10A 926361 F2262 E42 S26361 F2262 E31 Socket strip 3phase 3x 8 jacks IEC320 C13 26361 F2262 L31 S26361 F2262 E301 Rack mount Kit Socket strip Rack mount Kit 2U horizontal 26361 F2262 L301 The offered Socket strips are documented in PRIMECENTER Rack Power Connection Concept htto extranet fujitsu siemens com vil pc vil orimergy building blocks rack systems pf primecenter cable en doc Rack integration order numbers To integrate a server or I O Box into a Rack by Factory additional Order numbers are mandatory Integrate a M4000 or M5000 server into a Rack by Factory RACK SER2 Integrate a I O Box into a Rack by Factory RACK SER1 Power Cords for PSU connection directly to Rack external Jacks Must only be ordered for direct Power connections outside of the Rack to a country specific jack Overview Order Description Number of Number of Numbers Power Cord It is recommended to order 1 Cord to each PSU cables needed cables needed for M4000 for M5000 SELX9P21U MR AC Power Cord for Continental Europe Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 12 38 Power supply unit and power supply connections SPARC ENTERPRISE M5000 h
4. There is no difference in settings and conditions for partitions configured with Uni XSB only or Quad XSB only This option is useful if only a partial memory mirroring within a certain partition is required but Uni XSB type XSB is too large to do so PAR O in the following example is a partition configured by using both Uni XSB and Quad XSB Motherboard V O Board base PARO Gigabit Ethemet Gigabit Ethemet MSHA LO boat PCI Express Link Card Link Card PCI Express PCI Express PCT Express PCI Express PCT Express PCI Express PCI Express PCI Express VO Board Server additional Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 23 38 CPU Module Product Overview SPARC ENTERPRISE M5000 servers use SPARC 64 VI processors which are multi core multi threading CPUs Each module contains two CPU chips 4 cores Up to four CPU modules can be installed in SPARC ENTERPRISE M5000 Appearance Features 90 nm copper wiring CMOS technology is used for these processors to provide high performance while achieving low power consumption Two CPU cores are built on each CPU chip using CMP Chip Multi Processing technology CPU module Instruction Arithmetic ti Instruction Arithmetic Instruction Arithmetic control eee oak control sar control at circuit sack circuit untit circuit LI cache Li cache LI cache LI cache Instru
5. com com products servers unix server 20hardware SPARC 20Enterprise 20server Pages default aspx Powertool Link http partners fujitsu siemens com com products servers unix Config 20and 20 Tools SPARC 20Enterprise 20Server 20Powerconfigurator Pages default aspx Available and supported external storage peripherals and UPS Links Please refer to http partners fujitsu siemens com com products storage Pages default aspx http partners fujitsu siemens com com products servers primergy conftools MatrixEP MatrixEP Pages default aspx PRIMEPOWER Open Connectivity incl IHV Support Matrix Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 38 38 Link Open page http partners fujitsu siemens com com products servers consulting Pages default aspx http extranet3 fujitsu siemens com products consulting prof_services open connectivity Information about UPS Uninterruptable Power Supplys UPSes are only available up to 20kVA for M8000 Masterguard rack mounted single phase UPSes with more power or 3phase are not available yet at FSC but the connection installation is supported by partners like MASTERGUARD 20kVA APC planned Links http partners fujitsu siemens com com products servers unix Pages default aspx Support Page Link For Datasheets for Service Packs Service Contracts please refer to http www fujitsu siemens com services productrelated_services enterprise_services html PR
6. depth If the mounting kits do NOT fit to the required rack please order additional kits separately For more details refer to the Product Facts PrimeCenter Rack Design Guide and Configuration PrimeCenter Rack To integrate a server or I O Box into a Rack by Factory additional Order numbers are mandatory see chapter Rack integration order numbers Safety Attention E To mount an M5000 server into a rack you have to take notice for the rules which are described in the Installation Guide for Form factor models E M5000 System Base Unit is only allowed to be mounted up to Rack height unit 27 lowest system height unit Up to 3 x M5000 serves in a common Rack are allowed f w P r e 2 MW Installation of PRIMEPOWER servers and SPARC Enterprise Servers in other 19 racks than PCR2 is supported only if the PRIMEPOWER Rack Installation Guidelines for PRIMEPOWER systems are fulfilled For more information see the FSC extranet at http manuals fujitsu siemens com servers sparc m4m5io pc rack install en 01 padf Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 4 38 Overview M4000 and M5000 Pf SPARC Enterprise M4000 SPARC Enterprise M5000 CPU Processor Chips multi core 4 x 2 15GHz SPARC 64VI 8 x 2 15GHz SPARC 64VI multi thread VMT 2 per module 2 per module SLC Second Level Cache per Processor Chip 2 cores 5 MB
7. each 2 CPU chips on CPU Module each 2 CPU chips on CPU Module 4 Memory Boards 8 Memory Boards each 8 slots DDR II SDRAM each 8 slots DDR II SDRAM max DIMM Slots DDR II Memory per expansion unit 8GB 16GB or 32 GB 8 DIMMs per unit Multi domains partitions ECC Advanced ECC IOU I O Unit hereafter called I O board i 2 second IOU is expansion 4 PCI E 8 lanes per PCI slot 8 PCI E 8 lanes per PCI slot 1 PCI X 133MHz 2 PCI X 133MHz _ Max Internal Disks 2 5 SAS Removalmedia _ DVD Standard DAT Option On boardGbEport1000Base T 4 2oneachiOU On board Serial o o O 2 Boxes each max 12 PCI slots 4 Boxes each max 12 PCI slots mounted to 1 IOU mounted to 2 IOU occupies 4 internal PCI E slots occupies 8 internal PCI E slots internal plus I O Boxes Redundant parts HDD PSU FAN PCl Cards DIMMs Software support amp consideration on configuration are required Memory Mirror function Hot replacable parts Hot swap Dynamic degradation CPU chips memory power supply units fans HDDs PCI cards only in multi path configuration RAS Management RAS features All major components can be automatically deconfigured after rebooting Deconfiguration minimizes system impact in case of an uncorrectable error Finer granularity to prevent propagation of errors Buses between ASICs are protected by ECC Memory mirroring optional XSCF Interfaces 2 LAN interface 100Base TX RJ45 1
8. rack mountable box only E Do NOT mix with 8bit drive within 1 box NOTES on BG57 MTC drives m These devices can be mounted in BG57 boxes only NOT in system cabinets BG57 for accessible devices cable connection diagrams with list of cables Connecting BG57 to controller with LVD I F D EPRCK BG57 4 bays 514 D EPRCK BG57 4 bays 51 4 Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 37 38 Cables for connecting BG57 boxes to SCSI controller up to 80MByte s device dependent D KB235 M3 SCSI cable 3m 68pin UHD and 68pin Amplimite SCSI cable 5m 68pin UHD and 68pin Amplimite D KB235 M8 SCSI cable 8m 68pin UHD and 68pin Amplimite D KB243 M10 SCSI Connection Cable 10m Cables to configure the BG57 box The cable connects 1 or 2 bays in a BG57 to 1 input connector of the box EPRCK AN60 Upgrade kit PW BG57 to 4 channel U160 Seabee aiid ne 1 kit 2 cables are included in BG57 This kit is needed when all 4 bays must be connected in EPRCK AN62 Change kit PW BG57 to 1 channel U160 daisy chain to 1 input connector of the box The standard cables of the box cannot be used in this case Service clearance These cables can be installed if the boxes contain drives with LVD I F only D KB235 M5 Service clearance rear side Service clearance front side M5000 Connectivity Please refer also to Sparc Enterprise Server Link htto oartners fujitsu siemens
9. rules requires a Request for Project Release To keep the initial costs low it is allowed as an exception to run a physical system board with only one MEM module This is allowed for PSB 0 or PSB 1 or both of them This is meaningful in cases where a basic server configuration with only two MEM modules is ordered together with an additional 209 l O tray To get the 27 1 0 tray working you have to move a CPU module and a MEM module from the first PSB to the second PSB PSBs with only one MEM module can only be configured in Uni XSB mode but not in Quad XSB mode If you run a PSB with only one MEM module you have to be aware of the risk in case Of uncorrectable memory errors In such a case the partition will panic and will not be bootable again until the memory fault is solved If reconfigured to quad XSB the CPU module which is placed in a XSB without memory will be disabled Memory Mirroring SPARC ENTERPRISE M5000 models provide hardware based memory mirroring to avert system downs even when multi bit errors are detected Features Memory mirroring is available in both Uni XSB and Quad XSB configurations In Quad XSB configuration however mirroring should be configured in units of four XSBs the same size as with Uni XSB configuration Mirroring cannot be configured using a single XSB Mixed configurations of mirrored and unmirrored SB XSB in one partition are supported on M5000 Memory mirroring configuration is performed
10. two Hard Disk Drive bays It contains two onboard LAN ports four PCI Express slots and one PCI X slot e System disk Each partition requires at least one system disk for Solaris installation System disks can be realized in any of the following ways To improve system reliability it is recommended to duplicating mirroring the system disk A Mount a Hard Disk Drive in a disk bay inside the server B Ultra 320 SCSI cards expansion file units together with external HDDs can also be used as system disks C When using SAN Boot fibre channel cards RAID devices and system disks must be prepared Use a disk ina RAID device as the system disk When installing the OS on the RAID device you need to prepare another installation server or use one partition as an installation server using method A above D LAN Boot from other SPARC Enterprise Server is also possible Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 9 38 M5000 Server Product ID List PART NUMBER LONG DESCRIPTION SHORT DESCRIPTION M5000 family SEFPAAA1S Fujitsu Siemens Computers SPARC Enterprise M5000 server SE M5000 2 1GHz Includes M5000 system 2x 2 1GHz CPUs 1 2x 2 1GHz CPU Modules 2P16GB 2x73GB 16GB system memory 2 ea 8GB memory boards 2x 73GB HDD 4 PSU 1 I O tray SEFPBAA1S Fujitsu Siemens Computers SPARC Enterprise M5000 server SE M5000 2 1GHz Includes M5000 system 4x 2 1GHz CPUs 2x 2x 2 1GHz CPU Modules 4P16GB 2x73
11. 1 support bracket ZB5211 for 19 rack BG5x are included Power supply unit providing redundant PSU configuration for D GPDS2 SV30 Power supply unit D GPDS2 DN413 E The redundant PSU adds dual AC power input feed to GPDS2 DN413 NOTES on electrical connection and installation of the box m The Disk Node DN413 can be installed in the 19 inch rack PRIMECENTER E The plug IEC320 of the AC power cord which is shipped with GPDS2 DN413 matches with the outlets of the multiple socket outlets in the 19 rack E The GPDS2 DN413 has two AC power cords if a redundant PSU is installed Note that the boxes do support dual AC power input feed when a redundant PSU is installed E To support dual AC power input feed the AC power cords of standard PSU and redundant PSU must be plugged into independent power grids circuits within the building s wiring E When connecting the cables from standard PSU and redundant PSU to the same power grid circuit within the building s wiring you will get redundant power supply functionality instead of dual AC power supply functionality E As long as standard PSU and redundant PSU are working accurately they share the output load The outputs of all PSUs are connected in parallel NOTES on ordering m The basic disk node for 19 rack GPDS2 DN413 does NOT include HDDs HDDs must be ordered as separate items E To configure DN413 with redundant power supply or support dual AC power input feed a redundant P
12. CI Card Product ID List Ethernet Controller Overview Order PCI for Factory Description Max Max in Supported type or X option System 1 O boat PCl e Dual Port Gb Ethernet MMF Integrat Fact PCl e Dual Port Gb Ethernet UTP Yes s eS s eS s eS Y Y Y 7280A 2 Y Integrat Y Y SAUE Bois A option Quad Giga Ethernet UTP incl n 4447 A Z Fact Adapter Oo Yes Integrat X1027A Z X option Max 2 PCl e Fact 10Gb Ethernet Dual Port per 1027A Z ees X5558A Transceiver 10GBASE SR 850nm 300m MMF In Options ca summery Domain Integrat con aa o Xoption Transceiver 10GBASE LR Pee jsssoaz iitogat SOM Integrat Serial Interface RS232 Controller Overview Order PCI for Factory Description Max Max in Supported Numbers options Bus Integration withina an in 1 O Box type or X option System I O boat aii PCI Serial Asynchronous Interface Integrat Cryptographic Host Bus Adapters Overview Order PCI for Factory Description Max Max in Numbers options Bus Integration withina an type or X option System I O boat X option Fact Integrat Crypto Accelerator 6000 Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 14 38 Fibre Channel Host Bus Adapters Overview Order PCI for Factory Description Max Max in Supported Numbers options Bus Integration withina an in l O Box type or X option System I O boat PAEA Dual 4Gb Fib
13. FUJITSU cou Product Facts SIEMENS S PA R C E n te r p ri se M 50 00 E Ee oo M5000 Server Pages 38 SPARC Enterprise M5000 Configuration Diagram m New products M5000 GR20 M5000 CL09 PI01 M5000 CL10 PI01 M5000 CL11 12 Pl01 m Withdrawn products Some minor corrections Chapter Mounting additional Memory with different sizes SystemArchitect PRIMEPOWER PW Hotline For further questions related to configurations for SE M5000 Systems with PC ARCHITECT or SYSTEM ARCHITECT do not hesitate to get in contact with SystemArchitect PRIMEPOWER PW Hotline mailto SA PW Hotline fujitsu siemens com Please add the respective configuration file SAR FILE Picture SPARC Enterprise M5000 server Picture I O Box for PCI expansion Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Contents Recommended 19 rack PRIMECENTER 2 with 1100 mm depth Overview M4000 and M5000 System Architecture Product Overview SPARC Enterprise M5000 Features M5000 Server Product ID List M5000 COD Capacity on Demand Server Product ID List M5000 COD Capacity on Demand CPU Right to Use License Product ID List M5000 Internal Storage Device Product ID List M5000 Filter Product ID List M5000 Power Cords for Rack internal use Product ID List Rack integration order numbers Power Cords for PSU connection directly to Rack external Jacks Solaris Operating System OS and other Software Product ID List M5000 PCI Ca
14. GB 16GB system memory 2 ea 8GB memory boards 2x 73GB HDD 4 PSU 1 I O tray SEFPBCA1S Fujitsu Siemens Computers SPARC Enterprise M5000 server SE M5000 2 1GHz Includes M5000 system 4x 2 1GHz CPUs 2x 2x 2 1GHz CPU Modules 4P32GB 2x73GB 32GB system memory 2 ea 16GB memory boards 2x 73GB HDD 4 PSU 1 I O tray SEFPCBA1S Fujitsu Siemens Computers SPARC Enterprise M5000 server SE M5000 2 1GHz Includes M5000 system 8x 2 1GHz CPUs 4x 2x 2 1GHz CPU Modules 8P32GB 2x73GB 32GB system memory 4 ea 8GB memory boards 2x 73GB HDD 4 PSU 1 I O tray SEFPCDB1S Fujitsu Siemens Computers SPARC Enterprise M5000 server SE M5000 2 1GHz Includes M5000 system 8x 2 1GHz CPUs 4x 2x 2 1GHz CPU Modules 8P64GB 4x73GB 64GB system memory 4 ea 16GB memory boards 4x 73GB HDD 4 PSU 2 I O tray M5000 GR20 Fujitsu Siemens Computers SPARC Enterprise M5000 server M5000 2 1GHz Includes M5000 system 2x 2 1GHz CPUs 1x CPU Module 64GB system 2P64GB 2x146GB memory 2 ea 32GB memory boards 2x 146GB HDD 4 PSU 1 I O tray 1xl O tray included ATO BU SEFASY11S M5000 CLO09 PI01 Fujitsu Siemens Computers SPARC Enterprise M5000 server M5000 ATO Includes M5000 system 6x 2 1GHz CPUs 3x CPU Modules 64GB 6P2 15GHz 64GB system memory 4 ea 16GB memory boards 4x 146GB HDD 4 PSU 2 4x146GB 2xl O Tray I O tray included ATO BU SEFASY11S M5000 CL10 P101 Fujitsu Siemens Computers SPARC Enterprise M5000 server M5000 ATO Inc
15. GHz or greater Equivalent CPUs i e SPARC AMD are suitable 512 MB or greater ee Windows XP One of the OS listed Windows2000 on the left is required RedHat Linux Solaris CD ROM DVD ROM either internal or external device is available LAN 1000Base T 100Base TX or 10Base T RS 232C ro necessarily required Browser Microsoft R Internet Explorer 6 0 or later One of the browsers Netscape ASHE TM 7 0 or later listed on the left is Mozilla 1 7 or later required Terminal Solaris Secure Shell One of the software software Open SSH items listed on the left SSH Other terminal software with equivalent function is required to use SSH via LAN Terminal Hyper terminal One of the software software Other terminal software with equivalent function items on the left is RS 232C required to use RS 232C connection via hub switch twisted pair cable duplexed XSCF LAN 3 Purchased D GP70F AL21 category 5 UTP cable simplexed XSCF LAN 2 separately TPCBL B005 direct Fast Ethernet direct cable simplexed XSCF LAN 1 Purchased connection DCBL FEA05 separately RS 232C RJ45 DSUB9 pin inch screw 1 Attached to not necessarily female DCBL RSDO5 the server required Before ordering cables check the product ID and length for suitability of configuration Ethernet Cables Cables for Ethernet 1000 Base TX Cable only for Rack internal use if both targets are ina common rack S26361 F3417 E500 UTP cat 5 enhanced customi
16. IMECENTER Rack Link http partners fujitsu siemens com com products servers primergy rackcomp racks Pages default aspx Further information and contacts mailto primepower pm fujitsu siemens com PRIMEPOWER Office Further information and contacts Risse Franz Josef mailto Franz Josef Risse fujitsu siemens com All rights including rights created by patent grant or registration of a utility model or design are Published by department Company stamp reserved Delivery subject to availability right of technical modifications reserved All hardware and software names used are trade names or trademarks of their respective Enterprise Server Products manufacturers Product Management Copyright Fujitsu Siemens Computers 06 2008 http www fujitsu siemens com
17. P configuration Motherboard FO Board 0 Memory ACCESS controller CPU Hi core 1 PCI Express PCI Express PCI X PCI Express PCI Express TA chip 2h j CPU core 1 PCI Express PCT Express PCI X Memory ACCESS controller PCI Express PCI Express 2 Dual core SPARC 64 VI processors are used in this server e 90nm copper wiring technology is used in the processor to provide higher performance at lower power consumption e The dual core processors have large caches primary cache instructions 128 KB data 128 KB per CPU core secondary cache 5 MB per CPU chip appropriate for enterprise class server systems e Multi core and multi threading technologies ensure high parallel processing performance e Both the primary and secondary cache use ECC Error Checking amp Correction for high reliability e Registers and ALU are all parity protected This further enhances the high reliability of the server 3 Integrated high reliability makes this server suitable for 24 hour operation e All address data paths between key LSIs such as CPU chips memory controllers I O controllers and system controllers are ECC protected for higher reliability e Key components are redundant and hot replacement is supported Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 7 38 4 Very flexible partitioning functions are provided Multiple independent systems can be built on a single s
18. SU GPDS2 SV30 must be ordered E The maximum Disks are 7 per SCSI string and 14 per Disk Node Box GPDS2 DN413 E Standard cable carrier and support brackets for 19 racks PCR2 BG5x E All basic boxes for DN413 include support brackets E 1 cable carrier ZB527 for mounting within 19 rack BG5x belongs to all DN413 The diagnostic is done via SCSI in band SAF TE SCSI Access Fault Tolerant Enclosure Daisy chaining of disk nodes packages DN413 or daisy chaining of the 2 strings of one disk node is not supported The disk node DN413 comes without SCSI cable 1 SCSI cable has to be ordered for each connection from a SCSI string 7 HDD bays to a SCSI controller within a node as separate items Order numbers see below chapter drawing E You may connect the 2 strings of a disk node DN413 to different compute nodes The DN413 is switched ON OFF by terminator power from the SCSI controller i e ON with ON of the first compute node and OFF with OFF of the last compute node If the temperature inside the DN413 reaches an abnormal level because of a fatale error all connected compute nodes shut down and switch off the disk node Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 35 38 Hard Disk drives for DN413 73 GByte 15 000rpm Ultra SCSI LVD320 Fast drives with short access time D GPDS2 FP84 _ Hard disk U320 10k 146 GB 146 GByte 10 000rpm Ultra SCSI LVD320 aa FP85 Hard disk a 300 ee 300 GB
19. al cabling shall be done by factory Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 36 38 BG57 for accessible devices Order number for BG57 Rack mountable box 3 HU 4 bays 1 6 high E 2 SCSI strings 2 bays each as standard D EPRCK BG57 19 Rack Box f changeable Peripheral E 4 SCSI strings 1 bay each with optional ERPRCK AN60 l 2channel U160 E 1 SCSI strings 4 bays with optional EPRCK AN62 E Each SCSI string may be connected to a different server Note NO redundant PSU available D EPRCK AN60 Upgrade kit PW BG57 to 4channel U160 For configurations with 4 SCSI strings with 1 bay each or 3 strings with 2x1 plus 1x2 bays D EPRCK AN62 Change kit PW BG57 to 1channel U160 For connecting the 4 bays of one BG57 to 1 SCSI string A l I 1 adapter AN55 required for each 8 bit device within a D EPBOX AN55 doption set for 8bit SE devices BG55 BG57 box Drives for BG57 36 GByte native to 72 GByte compressed 16bit Install in EPRCK BG57 rack mountable box only D EPBOX MC57 MTC DAT72 36 72GB box l yD m Do NOT mix with 8bit drive within 1 box E Current Control CD required 80 GByte native to 160 GByte compressed l f 16bit Install in EPRCK BG57 rack mountable_box only PAEROA E OEE LVD E Do NOT mix with 8bit drive within 1 box E Current Control CD required 16bit 200 GByte native to 400 GByte compressed D EPBOX MC88 MTC LTO 2 HH 200 400GB LVD E Install in EPRCK BG57
20. as 2 2 redundant power supply units four in total Connect the power supply units as follows Single Power Feed Dual Power Feed fa NIAN SYNS 7 HDD HDD 3 HoD HDD Dar DVD HDD 0 HDD 2 Power Power Power Power supply supply supply supply unit 0 unit 1 unit 2 unit 3 Le If an uninterruptible Power Supply UPS is used it shall only supply one of the two power feeds Solaris Operating System OS and other Software Product ID List The SPARC Enterprise M5000 servers come with the Solaris 10 Operating System preinstalled on an HDD Media Kit SOLZ9 100C9A7M Solaris 10 OS Media kit Solaris 10 latest release DVD Media Kit Multilingual no hardcopy documentation no license Note Must be ordered with each system if Premium Pack is not ordered One of these two U24529 C590A Solaris 10 CD Set Premium Pack positions must be With additional SW Components on the control DVD ServerView Suite etc ordered for each This includes system SOLZ9 100C9A7M Solaris 10 latest release DVD Media Kit U24529 C503A control DVD Note Must be ordered with each system if OS Media kit is not ordered Solaris 10 Accessories Kit SPARC Enterprise Server Low End and Midrange and ESF CD Partition DR SCF interface etc U24529 C502A with each system etch Note Can be ordered with Crypto Accelerator Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 13 38 M5000 P
21. ction 128 KB Instruction 128 KB Instruction 128 KB Instruction 128 KB Data 128 KB Data 178 KB Data 128 KB Data 178 KB 2s a U L2 cache 5 MB 512 KB x 10 WAYs L2 cache 5 MB 512 KB x 10 WAYs CMT Chip Multi Threading technology provides multi thread processing that virtualizes each CPU core as two threads The use of register renaming out of order execution and non blocking cache memory ensures high parallel processing performance These modules offer mainframe levels of reliability inherited from SPARC 64 V e Data in both primary and secondary caches are protected by ECC Error Checking and Correction e e Registers and ALU are protected by parity e f an error occurs the hardware re executes the instruction that triggered the error Not all errors are covered by this feature e If recoverable errors occur frequently in cache hardware set degrade mode is automatically invoked Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 24 38 Specifications Items Specifications Remarks __ _ _ CPU SPARC 64 VI a Frequency 2 15 GHz Primary cache Instructions 128 KB per core data 128 KB Secondary cache Both the instruction and data 5 MB per CPU 2 cores pe ee a 2 CPU chips 4 cores SPARC ENTERPRISE M5000 M5000 CPU Product ID List Maximum Number Marketing P N Option Description Supported per System Comments Dual processor Modules SELX1A1U Without fac
22. dard a Mo cscussgieeddcosiossicesSevesdeobssuscesbievsdasobses scedvescodieodbes acsesnee5e Additional drives need to order the following HDD s Pteni SEP XY X3A11U 1x 73GB 2 5 SAS 10k rpm Second Internal I O Board optional 2 internal disk bays standard Additional drives need to order the following HDD s SEP XY X3Al1U__1x 73GB_2 5 SAS 10k rpm n onboard 1 Gbit Copper LAN Four PSU standard 2 default plus 2 redundancy SEN YX 8BE1S 1 O Expansion PCI Box with 1 PCI Express boat as standard OR SEN YX 8BX1S I O Expansion PCI Box with 1 PCI X boat as standard PCI PCI PCI PCI PCI PCI Second Boat optional SEN YX 8TE1U as PCI Express OR SEN YX 8TX1U as PCI X PCI PCI PCI PCI PCI PCI SEN YX 8BE1S 1 O Expansion PCI Box with 1 PCI Express boat as standard OR SEN YX 8BX1S I O Expansion PCI Box with 1 PCI X boat as standard PCI PCI PCI PCI PCI PCI Second Boat optional SEN YX 8TE1U as PCI Express OR SEN YX 8TX1U as PCI X PCI PCI PCI PCI PCI PCI sa se sa Sel ba se SEN YX 8BE1S I O Expansion PCI Box with 1 PCI Express boat as standard OR SEN YX 8BX1S I O Expansion PCI Box with 1 PCI X boat as standard PCI PCI PCI PCI PCI PCI Second Boat optional SEN YX 8TE1U as PCI Express OR SEN YX 8TX1U as PCI X PCI PCI PCI PCI PCI PCI SEN YX 8BE1S I O Expansion PCI Box with 1 PCI Express boat as standard OR SEN YX 8BX1S I O Expansion PCI Box with 1 PCI X b
23. ense for one Capacity on Demand COD CPU for use with SPARC Enterprise 1 CPU FF model M4000 and M5000 servers Note to COD COD Licenses are automatically arranged by the service processor XSCF see also Server Administration Guide Licenses can only manually be assigned to domains but not to hardware components like CPU If licenses are manually assigned to domains the licenses will be automatically arranged to the CPU s of this domain first CPU gets first license which is assigned for this domain second CPU gets second license and so on If there is only one big domain the arrangement is the same First CPU gets first license which is assigned for this domain second CPU gets second license and so on Result for M5000 To use the second system board in one big domain over the complete system a minimum of 5 licenses is necessary In addition the Note to Memory ordering is also permissible for COD server M5000 Internal Storage Device Product ID List Maximum Number Marketing P N Option Description Supported per System Comments 2 I O tray required MR 73GB 10K RPM SAS Hard Disk Drive for HDD 3 amp 4 on SEPX3A11U Without factory integration Up to 4 per M5000 M5000 2 1 O tray required MR 73GB 10K RPM SAS Hard Disk Drive for HDD 3 amp 4 on SEPY3A11U Factory integration only Up to 4 per M5000 M5000 2 1 O tray required MR 146GB 10K RPM SAS Hard Disk Drive for HDD 3 amp 4 on SEPX3C11U Without factory integration U
24. er Channel Network POLE Fact Adapter RoHS 6 compliant SG PCIE2FC QF4 Ves ntegrat SATER ant oce ten Dual 4Gb Fiber Channel Network ue Fact Adapter RoHS 6 compliant SG PCIE2FC EM4 Yes Integrat SG XPCIE1FC QF4 Single 4Gb Fiber Channel Network Fact Adapter RoHS 6 compliant Integrat SG PCIE1FC QF4 laden dai A opuon Single 4Gb Fiber Channel Network pve Fact Adapter RoHS 6 compliant Integrat eisai dial open Dual 4Gb Fiber Channel Network as Fact Adapter RoHS 6 compliant Integrat B APRON Dual 4Gb Fiber Channel Network PCI X l Fact Adapter RoHS 6 compliant SG PCI2FC EM4 Z Integrat E A Opto Single 4Gb Fiber Channel Network PCI X l Fact Adapter RoHS 6 compliant SG PCI1FC QF4 Integrat SG XPCI1FC EM4 Z X option PCI X Single 4Gb Fiber Channel Network Fact Adapter RoHS 6 compliant SG PCI1FC EM4 Z Integrat SCSI Host Bus Adapters Overview Order PCI for Factory Description Max Max in Supported Numbers options Bus Integration withina an in 1 O Box or X option System l O boat PCI E Dual channel Ultra320 low A AA OPLO voltage differential SCSI host bus PCl e 2 es Fact adapter includes standard and low SG PCIE2SCSIU3202 profile brackets ROHS 6 compliant Note e SCSI Controller SG X PCIE2SCSIU320Z using Solaris 10 Update 3 can only be placed in PCl express slot 2 3 or 4 from both IOUs not in PCl express slot 1 nor in I O Box which is connected to this slot Us
25. erver called partitions or domains Each partition can individually be configured Up to four partitions are supported The motherboard on which CPU and memory modules are mounted is sub divided into eight parts and the two I O board are sub divided into four A combination of sub parts from motherboard and I O board form a partition in maximum 4 5 Partition independent processor based system control facility XSCF eXtended System Control Facility XSCF detects abnormal conditions and controls the system without relying on system status such as CPU abnormality or system hang Mutual monitoring abnormal CPU notification fan rotation frequency monitoring control power monitoring control humidity temperature monitoring etc are provided Monitoring control of peripheral devices such as RCl connected units cluster nodes and expansion cabinets is available via RCI Remote Cabinet Interface Remote power on off is also available The operational status of the server can also be monitored by XSCF The embedded partition control facility renders the need for an external control console terminal unnecessary 6 Remote Customer Support Remote Customer Support will be handled via Teleservice 7 ServerView Enterprise Edition 2 0 is available for download in the FSC Software Pool ServerView Enterprise Edition 2 0 provides consolidated management of all FSC servers including PRIMEPOWER SPARC Enterprise PRIMEQUEST and PRIMERGY Serve
26. f PCI Express slot lane and shows eight lanes are supported shows PCI slots support a 64 bit width and any PCI card with a 64 bit or 32 bit width can be used indicates operating frequencies supported by each PCI slot When a 133 MHz operable PCI card is installed indicates the voltage levels of PCI cards that can operate in the slot 3 3 V PCI cards and universal PCI cards PCI cards that can work at either 3 3 V or 5 V can be mounted in any slot PCI cards that only work PCI Bus indicates the types of I O boat LINKO are mounted No of Lanes Bus Width Clock Rate the clock rate becomes 133 MHz Input Voltage in 5 V slots cannot be used Card Size Connection Types example PC Express PCI Express Cink Card t PCI Express j Link Card PCI Express Link Card pk E Link Card Card O S indicates short length PCI cards and L indicates long length PCI cards can be installed O boat H Link Card PCI Express PCI Express PCI Express Link cable PCI Express PCI Express L O boat V O boat PCI Express PCI Express Connection between server and I O Box is realized by Fibre or Copper Link Card Kit Link Card and a dedicated cable set Link cable Insert the Link Card in a PCI Express slot on the server Cascade connection of I O boats is not supported Expansion M5000 Up to 4 external I O Bo
27. from the XSCF For more information refer to eXtended System Control Facility User s Guide When mirroring is configured the available memory capacity on each SB XSB one half of the total size Mirroring is done within a group using combinations as shown below Thus the memory size in Groups A and B can be different T r H J Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 27 38 Mounting additional Memory with different sizes MEM in SPARC Enterprise M5000 is organized on each SB separately in two groups e Max 16 DIMMs mounted in MEM xA slots at SB 0 defined as Group A of SB 0 e Max 16 DIMMs mounted in MEM xB slots at SB 0 defined as Group B of SB 0 e In Group B at SB 0 all DIMMs must have the same Capacity In Group A at SB 0 all DIMMs must have the same Capacity and this Capacity must be equal or bigger than the DIMMs of Group B This DIMM Mix within a SB is possible in Uni XSB and Quad XSB Mode e Max 16 DIMMs mounted in MEM xA slots at SB 1 defined as Group A of SB 1 e Max 16 DIMMs mounted in MEM xB slots at SB 1 defined as Group B of SB 1 e In Group B at SB 1 all DIMMs must have the same Capacity In Group A at SB 1 all DIMMs must have the same Capacity and this Capacity must be equal or bigger than the DIMMs of Group B This DIMM Mix within a SB is possible in Uni XSB and Quad XSB Mode e Memory configurations and arrangements on SB 0 and on SB 1 can be different
28. have the same MAC address by default Therefore do not connect them to the same subnet before you have changed the default MAC address You can assign unique MAC addresses to respective LAN ports by changing the OBP environment variable local mac address to true 2 DVD ROM drive and the internal DAT drive cannot be connected to the expansion second I O board of the SPARC ENTERPRISE M5000 Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 31 38 l O BOX Product Overview The External I O Expansion Unit hereafter referred to as I O Box is a rack mountable expansion unit used to expand the server s I O connectivity with up to 12 PCI Express or PCI X slots Each I O box can contain two External I O kits hereafter referred to as I O boats giving 12 slots in total Each I O boat provides either six PCI Express or six PCI X slots To connect to the I O boat insert a Link Card into a PCI Express slot on the server and connect them with a cable kit Up to four I O Boxes can be connected resulting in 48 external PCI slots for a M5000 z h gt Preliminary art Appearance provisional Features e Each I O Box comes with one I O boat for six PCI Express or six PCI X slots as standard By adding a second PCI Express or PCI X I O boat the I O Box can provide a maximum of 12 slots There are two kinds of expansion I O boats PCI Express and PCI X Mixed I O boat configuration is supported B
29. hen mounting DIMMs to a specific group the memory size must be identical within this group DIMMs of different memory sizes cannot be mounted within a group Condition 4 Memory size in Group A must be greater than or equal to that in Group B These rules are true for mirrored and not mirrored memory configurations When mounting additional memory with different memory sizes transfer already mounted DIMMs as necessary and follow the above conditions Example of Memory Expansion for SB 0 IGB DIMMs are already mounted Add 2 sets of 16GB memory module 2GB DIMM x amp Gea Transfer the DIMMs so that DIMMs of different sizes will not be mixed in neither Group A nor Group B CPU H2 2core CPUS 2core Group A Group B Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 29 38 Memory Interleaving Memory interleaving is a technique that divides main memory into several blocks WAYs and accesses each WAY independently and in parallel to enable effective access to the contiguous area The size of one WAY is 64 bytes which is the line size of cache memory SPARC ENTERPRISE M4000 M5000 perform memory interleaving in Group units as standard The number of WAYs in each configuration is as follows Uni XSB configuration 16 DIMMs of memory are mounted in Groups A and B WAYI J WAY2 WAYS WAY4 WAYS Group A Group B Uni XSB configuration 8 DIMMs of memory are mounted in Group
30. ing Solaris 10 Update 4 or higher versions this SCSI Controller is also allowed in PCl express Slot 1 see table above Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 15 38 Console Connection For APL a personal computer PC or workstation is required for system control and maintenance work This console must be setup prior to installation of APL The XSCF is accessed using this console The console ports of each partition are accessed via XSCF XSCF and the console need to be connected via LAN If you forget the XSCF sign on password you will need to connect to XSCF via RS 232C for recovery The customers console terminal should meet the following conditions e https or http and ssh or telnet available for details see the following specifications e The terminal needs to be placed within 15 m from the server e Amaintenance account account for field engineer privileges for field engineers set up in advance For details on account creation see eXtended System Control Facility User s Guide Where the customer has no prepared terminal or the field engineer cannot use the terminal prepared by the customer approval to use the field engineer s own PC should be gained from the customer Field engineers can connect their own PC to the XSCF via XSCF LAN or RS 232C XSCF LAN is used as standard However in special cases if XSCF LAN is not available or the XSCF sign on password needs initializat
31. ion RS 232C is used Console connection example field engineer uses a terminal setup by customer use either connection telnet ssh via HUB or direct connection and j n http https PC or similar to a router for REMCS APL FFI FF2 use either connection te net ssh via HUB or direct connection and XSCFHO http https to a router for REMCS Note For the HUB in the pictures our LAN Switch D GP70F AL21 can be ordered Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 16 38 Console connection example Field engineer connects temporarily a PC via LAN shown as blue line or RS 232C shown as dotted line as required to provide maintenance use either connection telnet ssh via HUB or direct connection and https PC or similar for customer use only p Oa router tor REMCS Console connection example the console path is duplicated Field engineer connects temporarily a PC via LAN Shown as blue line or RS 232C shown as dotted line as required to provide maintenance use either connection APL FFI FF2 via HUB or direct connection telnet ssh LANA to a router for REMCS ii Field engineer s PC Note For the HUB in the picture our LAN Switch D GP70F AL21 can be ordered Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 17 38 Specifications for the PC or the workstation etc __ Deseription 0 Reraries Pentium3 1
32. ludes M5000 system 6x 2 1GHz CPUs 3x CPU Modules 96GB 6P2 15GHz 96GB system memory 6 ea 16GB memory boards 4x 146GB HDD 4 PSU 2 4x146GB 2xl O Tray I O tray included ATO BU SEFASY11S M5000 CL11 12 Fujitsu Siemens Computers SPARC Enterprise M5000 server M5000 ATO P101 Includes M5000 system 8x 2 1GHz CPUs 4x CPU Modules 96GB 8P2 15GHz 96GB system memory 6 ea 16GB memory boards 4x 146GB HDD 4 PSU 2 4x146GB 2xl O Tray I O tray included ATO BU SEFASY11S Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 10 38 M5000 COD Capacity on Demand Server Product ID List PART NUMBER LONG DESCRIPTION SHORT DESCRIPTION M5000family SEFRCDB1S FSC SPARC Enterprise M5000 COD Capacity On Demand server M5CoD 2 1GHz Includes 8x 2 15GHz CPUs 4 CPU boards with 2 x CPUs each 5MB on 8P64GB 4x73GB chip L2 cache and 64GB system memory 4 memory modules with 8 x 2xl O tray 2GB DDR2 DIMMs 4 x 73GB SAS hard disks 1 DVD ROM 2x 1Gb Ethernet ports 2 I O trays with 8 PCI E and 2 PCI X slots total 4 power supplies includes redundancy and DPF As minimum to each COD System 2 RTU Right To Use licenses are required must be ordered together with the system M5000 COD Capacity on Demand CPU Right to Use License Product ID List PART NUMBER LONG DESCRIPTION SHORT DESCRIPTION M5000 family SELX9RU1S FSC SPARC Enterprise Server COD 2 0 Right To Use RTU license for CoD RTU lic
33. n only 8 per M5000 Purchase Factory integration only modules if you need the memory modules installed and shipped inside the server Without factory integration means modules are always shipped uninstalled even if they are ordered with the server Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 26 38 Notes on Memory ordering Two sets of memory modules with the same size 16 DIMMs must be mounted on a physical system board as a minimum 8 DIMMS are always handled as one set When adding memory two sets of memory modules with the same size must be added at the same time Memory can only be added in increments of 2x eight DIMMs Only 2 4 6 or 8 Memory Modules are allowed For mixing DIMMs with different sizes special conditions have to be noticed see chapter Mounting additional Memory with different sizes If Memory Modules are installed on the second physical System Board a CPU module on this PSB is mandatory and vice versa If a second internal O tray is installed at least one CPU module and two Memory modules on the second physical System Board are mandatory see also Memory Exception rules Min of 1 memory module per processor in Quad XSB Mode Hint When ordering 4Gb DIMMs the customer has to specify how FSC shall deal with the memory which comes with the base configuration It can either be delivered in a separate package or placed in MEM slots which remain open Memory Exception
34. nterprise M5000 Page 20 38 2 Quad XSB Because Quad XSB allows to configure several partitions in units of individual CPU chips two cores it is the optimized way to create small partitions Quad XSB is equivalent to the XSB definition for PRIMEPOWER Division Type Quad XSB rT mm r om mm emer me ome e r e ee ee ee ee e eo Motherboard LO Board base i p edditional PSB consists of 1 2 motherboard and an I O board is divided into four partitions with 1 CPU chip and a set of memory 8 DIMMs each PSBs can be divided into XSBs XSB 0 0 XSB 0 1 XSB 1 0 XSB 1 1 with connection to an I O board and XSBs XSB 0 2 XSB 0 3 XSB 1 2 XSB 1 3 without connection to an I O board CPU chips memory PCI slots and disks are permanently assigned to the XSBs as shown in the diagram above XSBs without connection to an I O cannot be configured as an autonomous partition refer to 8 4 Notes on Configurations for details Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 21 38 Example for four partitions configured with two XSBs Mothe board _ LO Board base PARSO PAR PAREZ PAR 3 L O Board Server additional Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 22 38 3 Combination of Uni XSB and Quad XSB PSBs divided into Quad XSBs can be mixed together with Uni XSB to configure a common partition
35. oat as standard Slot Slot Slot Slot Slot Slot Second Boat optional SEN YX 8TE1U as PCI Express OR SEN YX 8TX1U as PCI X PCI PCI PCI PCI Slot Slot Slot Slot Slot Slot D GPDS2 DN413 SCSI HDD JBOD 7diskbay DOOQOOOO lt 7disk bay DOQ CO C2 CQ C CE D GPDS2 SV30 Redundant PSU SH ill D EPRCK BG57 Peripheral Box 2x 2bay 1 6 inch hight or 2x 1bay 3 2 inch hight For changeable media drives K N 1 6 inch hight 1 6 inch hight 1 6 inch hight 1 6 inch hight Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 6 38 Product Overview SPARC Enterprise M5000 SPARC ENTERPRISE M5000 is a midrange server developed using the expertise of Fujitsu and Sun Microsystems It has been designed to be the best choice in mission critical computing solutions High scalability comes from eight CPU chips 16 cores and is backed by exceptional reliability and excellent means for asset investment protection Based on SMP Symmetric Multi Processing architecture it delivers high scalability without change to applications Features 1 SPARC ENTERPRISE M5000 is a scalable enterprise server e Up to eight dual core CPU chips can be installed e Upto 256 GB of memory and 50 I O slots when four I O Boxes are connected are supported for excellent scalability e The maximum data transfer performance of 64 GB s ensures excellent linear scalability up to 16 processor cores in an SM
36. oth PCI Express and PCI X slot types support PCI HotPlug for I O cards Hot replacement and hot system expansion for each I O boat is also supported Each I O Box has 1 1 redundant power supply units and supports single or dual power feed Hot replacement for each power supply unit is supported The I O Box can be mounted in a 19 inch rack 4U Specifications Items Specifications Slot type PCI Express 6 PCI X 6 number system Maximum PCI Express 12 PCI X 12 depending on the I O number or or boat types which are PCI Express 6 and PCI Express 6 and mounted PCI X 6 PCI X 6 Redundant components Power supply units power system Pe Hot replaceable PCI cards I O boats power supply units ee components M4000 M5000 SS IO boat PCI Slot Specifications I O boat for PCI Express PciBus SlotNo No of Lanes CardSize pT LINKO forexclusive use with a Link Card __ PCI Express PCIE1 8 J i PCIE J8 JSE i PCIE3S J8 JSE S PCIE4 J8 SSE S PCIE5S 8 SSE S PCIE 8 J E S I O boat for PCI X PCI Bus SlotNo Bus Width Clock Rate Input Voltage LINKO for exclusive use with a Link Card PCI X PCIX1 64 32 bit 133 MHz 3 3 V Universal PCIX2 64 32 bit 133 MHz 3 3 V Universal Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 32 38 indicates slots where Link Cards separately purchased PCI cards for connecting the server and the I O Box indicates the width o
37. p to 4 per M5000 M5000 2 1 O tray required MR 146GB 10K RPM SAS Hard Disk Drive for HDD 3 amp 4 on SEPY3C11U Factory integration only Up to 4 per M5000 M5000 zaor liae ae O ee SELX9DT1U Without factory integration Up to 1 per M5000 sarono Penman sea SELY9DT1U Factory integration only Up to 1 per M5000 M5000 Filter Product ID List Maximum Number Marketing P N Option Description Supported per System Comments SEEX9FL1U M4000 air filter kit 1 per system SEFX9FL1U M5000 air filter kit 1 per system re Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 11 38 M5000 Power Cords for Rack internal use Product ID List Attention For each PSU a Power Cord must be ordered for Rack internal connection thickly marked in table below to the Socket strip Note M5000 requires 4x 16A power cords each I O Box requires 2x 10A power cords Power Cord to a Rack internal Socket strip 16 A Is a Standard Part of each System PSU For System Base Units Socket strip 1 phasen 32A SDL S26361 F2262 E132 In combination with the PSU of 1x 3 jacks IEC320 C19 16A the Base Units amp 1x plug IEC309 CEEform blue 32A In combination with the PSU of Socket strip 3 phasen 32A SDL S26361 F2262 E332 the I O Boxes 3x 3 jacks IEC320 C19 16A 3x 2 jacks IEC320 C13 10A S26361 F2262 L332 1x plug IEC309 CEEform red 32A Power Cord to a Rack internal Socket strip 10 A SERXP333WS For 1 O Box
38. r managing functions for all managed servers such as hardware configuration display and status monitoring are provided for system administrators via a unified GUI and standard operating processes a The status monitoring of all servers is available from a single management client The status of key components such as CPU memory of each server can be displayed in a unified tree view b When server components fail SVS EE displays each event graphically together with the relevant message for prompt defective part location c Server management can be performed with unified operability 8 The DR Dynamic Reconfiguration functions are supported Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 8 38 9 Configuration Diagram of the Main Unit Top view Areas indicated in blue show components belonging to the base units those indicated in red show options purchased separately but see also base unit description 10 Hardware for M5000 e Motherboard The motherboard carries CPU modules and memory modules Four CPU modules eight CPU chips and eight memory modules 64 DIMMs can be mounted The motherboard is part of the base unit e 1 I O board standard ae I O board has a connection to two Hard Disk Drive bays one DVD Drive bay and one DAT Drive bay It contains two onboard LAN ports four PCI Express slots and one PCI X slot ond I O board optional Tre 2 I O board has a connection to
39. r of system shutdowns caused by memory failures 5 Memory mirroring function enables continued operation even when an uncorrectable error multi bit error occurs 6 When memory failure is detected at initial diagnosis or during OS operation Block Degradation or Area Degradation occurs Because the area to be degraded is designed to be a controllable minimum area other areas remain intact Thus operation can continue resume using these areas This minimizes the effects of failures 7 MEM controller patrols memory during normal operation independently from the CPU and OS This hardware can detect an error and degrade the area before either the OS or an application is affected This procedure doesn t have any effect on other operations M5000 Memory Product ID List Maximum Number Marketing P N Option Description Supported per System Comments 8GB MR with server memory board and SELX2A1U Without factory integration 8 per M5000 8GB MR with server memory board and SELY2A1U Factory integration only 8 per M5000 16GB MR with server memory board and 8x 2GB DIMMs 4 per M4000 SELX2B1U Without factory integration 8 per M5000 16GB MR with server memory board and 8x 2GB DIMMs 4 per M4000 SELY2B1U Factory integration only 8 per M5000 32GB MR with server memory board and 8x 4GB DIMMs 4 per M4000 SELX2C1U Without factory integration 8 per M5000 32GB MR with server memory board and 8x 4GB DIMMs 4 per M4000 SELY2C1U Factory integratio
40. rchased separately It is not supported to connect the two IO boats within one O Box to different servers If two I O boats are equipped they have to be connected to the same server Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 34 38 External storage units for M5000 External storage units for HDDs or MTC drives differential SCSI DN413 disk node for high performance HDD Overall view disk nodes new generation Disk node Drive interface DN413 U320 SCSI Wide LVD Node interface U320 SCSI Wide LVD Capacity per disk 73 GByte 146 GByte 300 GByte Maximum capacity disk node 2x 7x300 4 2 TByte Cabinet type 19 rack mount 3 HU Redundant components Fan std PSU DPF option Controller to connect HBA SG X PCIE2SCSIU320Z Throughput 2x 320 MByte s Maximum cable length 10m Max number of DN413 per dual 1x DN413 4 TByte port HBA 0 1 by SW RAID level Cluster Zz 1 2 cables 1 2 HBA 1 14 Disk s FP81 FP84 or FP85 FP86 Required additional components Rack for mounting Disk nodes DN413 are for single server nodes For the order numbers see table below Order number for disk node DN4x Disk Subsystem for single node configuration E 2 SCSI strings with 7 HDD bays each for disks with SCSI U320 LVD I F i E 2 SCSI connection module single port U320 D GPDS2 DN413 Disk Subsystem E rack mountable box needs 3U in a 19 rack E cable carrier ZB527 and
41. rd Product ID List Ethernet Controller Serial Interface RS232 Controller Cryptographic Host Bus Adapters Fibre Channel Host Bus Adapters SCSI Host Bus Adapters Console Connection Ethernet Cables Partitioning CPU Module M5000 CPU Product ID List Additional Memory Module M5000 Memory Product ID List Notes on Memory ordering Memory Exception rules requires a Request for Project Release Memory Mirroring Mounting additional Memory with different sizes Memory Interleaving I O Board M5000 second I O Board Product ID List 1 O BOX M5000 external I O Box Product ID List External storage units for M5000 External storage units for HDDs or MTC drives differential SCSI DN413 disk node for high performance HDD Hard Disk drives for DN413 Disk subsystems cable connection diagrams with cable list Connecting Disk node DN413 to SCSI HBAs within single node configurations BG57 for accessible devices Order number for BG57 Drives for BG57 BG57 for accessible devices cable connection diagrams with list of cables Connecting BG57 to controller with LVD I F Service clearance M5000 Connectivity Further information and contacts Page 2 38 oO 00 WHO Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 3 38 Recommended 19 rack PRIMECENTER 2 with 1100 mm depth 24 HU height BHU height 4G HUeight _ m SPARC Enterprise M5000 servers can be mounted in PCR2 Rack versions with 1100 mm
42. rrent Status For order of PCI X I O Boat a Request for Special currently without SENX8TX1U Release is necessary Controller support 1x copper Link card Kit 2 boards 2 x 4M copper cables for External I O Expansion Unit copper Link Card SELY8LK1U Factory integration only Kit 4 M 1x copper Link card Kit 2 boards 2 x 4M copper cables for External I O Expansion Unit copper Link Card SELX8LK1U Without factory integration Kit 4 M 1x Optical Link card Kit 2 boards 2 10M optical cables for External I O SENY8LK2U Factory integration only Kit 10 M 1x Optical Link card Kit 2 boards 2 10M optical cables for External I O Expansion Unit Optical Link Card SENX8LK2U Without factory integration Kit 10 M 1x Optical Link card Kit 2 boards 2 x 25M optical cables for External I O Expansion Unit Optical Link Card SENY8LK3U Factory integration only Kit 25 M 1x Optical Link card Kit 2 boards 2 x 25M optical cables for External I O Expansion Unit Optical Link Card SENX8LK3U Without factory integration Kit 25 M 1x Optical Link Cable Set 10m optical cable for External I O Expansion Unit Optical Link Cable SENX8FC1U Without factory integration only 10m 1x Optical Link Cable Set 25m optical cable for External I O Expansion SENX8FC2U Without factory integration only 25m Notes Toconnect to a server each I O boat requires its own Link Card Kit The Link Card Kits are not included in the basic I O Box configuration and must be pu
43. s A and B WAYI WAY2 Group A Aw AY Group B AWAY E S WAYI Group A 2WAY Group B 2WAY Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 30 38 I O Board also called I O tray or I O Unit IOU Product Overview The SPARC ENTERPRISE M5000 basic configuration contains one I O board A second I O board can be added to SPARC ENTERPRISE M5000 Appearance Features e The I O board provides four PCI Express slots and one PCI X slot e The I O board has two on board Gigabit Ethernet ports and SAS connections to two hard disk drives e The first I O board has a connection to the DVD drive and to the optional internal DAT drive Specifications Items sd Specifications Remarks po Internal VO Unit Are in base unit as standard On board I O 2x 1000Base T ports ff Internal PCI slot _4 slots PCI Express each 8 lanes o 1x PCI X 1 slot o po Internal optical drive Connection to 1x DVD drive DVD ROM 8X CD ROM 24X Internal tape device Connection to 1x DAT72 re M5000 second I O Board Product ID List Maximum Number Marketing P N Option Description Supported per System Comments SEFX61U Without factory integration Up to 1 per M5000 MR I O Tray 4 PCle and 1 PCI X slots SEFY61U Factory integration only Up to 1 per M5000 Note for chapter I O Board 1 Notes on LAN connection LAN ports on the I O Board and on LAN PCI Express cards belonging to the same partition
44. serial port RS232 RJ45 1 RCI interface Fujitsu FSC proprietary interface 1 USB port for service only Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 5 38 System Architecture PRIMECENTER 2 Rack deep 1100mm 24U 38U 46U PC LAN Console 10U p to 8 CPU 4 Module SPARC64 VI Up to 16 core 2 Threads o N 2 15GHz 5MB SLC for 1 CPU 2 cores Type Serrial 2 CPU 2 15GHz on a Processor Module Management CPU Module CPU Module CPU Module CPU Module Main Memory options up to 256 GB within 4GB DIMMs MEM order Type SEL XY 2A1U 8 x 1 GB DIMM SEL XY 2B1U 8 x 2 GB DIMM SEL XY 2C1U 8 x 4 GB DIMM U320 SCSI Contr PCI e 1 G bit LAN Contr PCI e LVD 2 port SG 2 port UTP copper X PCIE2SCSIU320Z X 7280A 2 MEM MEM MEM MEM MEM MEM JMEM MEM rer eee wccccccccccccccccscceel w Peer eee UU Pere Cree rrrrrrrrr errr errr errr rier rr rrr rr rrrrere as MEM MEM MEM MEM MEM MEM MEM MEM e 1 G bit LAN Contr PCI e Crypto Accelerator 6000 PCI e X 7281A 2 X 6000A a seas Coakdaeteciadeiederd WD coat ised teccccincsstedeaaescdcbsivedossdosicccdscuisalisdecane Fibre Channel 4Gb Fibre Channel 4Gb 1 port 1 port SG X PCIE1FC EM4 2 port MMF optic Internal I O Board standard 1 internal DVD standard l Fibre ae 4Gb or 1 internal DAT optional i p p SG X PCIE2FC QF4 2 internal disk bays stan
45. tory integration 4 per M5000 SELY1A1U Factory integration only 4 per M5000 Purchase Factory installed modules if you need the CPU modules installed and shipped inside the server Field expansion modules are always shipped uninstalled even if they are purchased together with the server Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 25 38 Additional Memory Module Product Overview SPARC ENTERPRISE M5000 memory module is an expansion memory device consisting of memory DIMMs and a memory controller equipped on a board that can be plugged to the motherboard There are 8 GB 16 GB and 32 GB additional memory module types with eight DIMMs each which can be added as a set Mounting of additional memory modules must be performed under specific conditions For details on how to add memory refer to Conditions for Mounting Additional Memory Appearance Memory Module Memory module without a cover Memory module 8 DIMMs are always mounted Features 1 1 Gbit 2 Gbit 4 Gbit DDR2 SDRAM Double Data Rate Synchronous Dynamic Random Access Memory is used to provide high speed access 2 High density DIMMs Dual Inline Memory Module are used to save space on the motherboard 3 ECC Error Checking and Correction functions provide higher system reliability 4 If a single memory chip on a DIMM fails completely it is handled as a single bit error This technique drastically reduces the numbe
46. xes with 2 boats each are connectable second internal IOU must be installed for third and fourth external I O Box Each I O boat is connected directly to the server and occupies one PCl express slot in internal IOU Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 33 38 M5000 external I O Box Product ID List Option Description Comments PCI Express External I O Expansion Unit w 2x PSUs w 1 PCI E Boat ROHS 6 Marketing P N If Factory integration will be accomplished or not depends on SENX8BE1S order sequencing currently without FSC Ext I O Exp Unit 1 PCI E FSC Ext I O Exp Unit 1 PCI X PCI X External I O Expansion Unit w 2x PSUs w 1 PCI X Boat ROHS 6 Without factory integration If Factory integration will be accomplished or not depends on order sequencing Current Status For order of PCI X I O Box a Request for Special SENX8BX1S Release is necessary Controller support mwen eeta onn ERRES SENY8TE1U Factory integration only I O Exp Unit SENX8TE1U Without factory integration I O Exp Unit PCI X lO Boat for External I O Expansion Unit ROHS 6 PCI X O Boat for Factory integration only I O Exp Unit Current Status For order of PCI X I O Boat a Request for Special currently without SENY8TX1U Release is necessary Controller support PCI X lO Boat for External I O Expansion Unit ROHS 6 PCI X O Boat for Without factory integration I O Exp Unit Cu
47. yte 10 000rpm Ultra SCSI LVD320 292 GByte of disk space 4 drives 73 GByte each D GPDS2 HDP4 HD packet with 4 x 146 GB U320 10Krpm 284 GByle of disk space 4 drives 146 GByte each Allowed in DN413 D GPDS2 FP86 Hard disk 73GB 15kRpm ee eo eee Fast drives with short access time D GPDS2 HDP5 HD bundle with 4 x 73 GB 15Krom er elas of disk space 4 drives 73 GByte and 15 000rpm NOTES on disks for DN413 E These HDDs can be mounted in DN413 boxes only but NOT in system cabinets Disk subsystems cable connection diagrams with cable list Connecting Disk node DN413 to SCSI HBAs within single node configurations up to 320 MByte s DN413 is not usable for shared disks in cluster configurations D GPDS2 DN413 Disk Subsystem Dual Port DOODDDOTS 7 disk bay o 7 disk bay D GPDS2 SV30 Redundant PSU The second UltraSCSI I O module in this drawing can either be connected to the second port of a DualPort HBA or to another HBA which may or may not belong to another partition Cables for connecting disk nodes DN413 to U320 SCSI HBA up to 320 MByte s D GPDS2 KB04 SCSI cable UHD68 S UHD68 S 4m DN41 D GPDS2 KB05 SCSI cable UHD68 S UHD68 S 5m DN41 Note on cable carrier The cable carrier D GPDS2 KB10 SCSI cable UHD68 S UHD68 S 10m DN41 GPRAG ZB527 requires additional cable length of SCSI cable UHD68 S UHD68 S customized length approx 1m SNP SY F2365E500 P needed if the rack intern
48. zed length Please order Factory integration UTP category 5 enhanced patch cable for Gbit Ethernet 1000Base T to connect controllers with a hub or switch S26361 F3417 L505 UTP cat 5 enhanced 05m eT ae omens 2an UTP category 5 enhanced patch cable for Gbit Ethernet 1 Base T Il hah h 26361 F3417 L515 UTP cat 5 enhanced 15m 000Base T to connect controllers with a hub or switc 1S26361 F3842 L5 UTP cat 5 enhanced IC cable 5m Lose UTP category 5 enhanced crossover cable for Gbit Ethernet 1000Base T to make direct connection between Ethernet controllers in a two node configuration S26361 F9842 E5 UTP cat 5 enhanced IC cable 5m Verbau Cables for Ethernet 1000 Base SX Please buy optical cables locally Product Facts Issue June 01 2008 Product SPARC Enterprise M5000 Page 18 38 Partitioning SPARC ENTERPRISE M5000 supports partitioning in which a single server can be divided into multiple independent systems Partitioning creates multiple independent systems which are called partitions or domains The basic hardware resource required for partitioning is a Physical System Board hereafter referred to as PSB A PSB consists of a motherboard with or without connection to an IOU A PSB can logically be divided into four parts In this case it is called a Quad XSB A PSB without such a division is called a Uni XSB The physical unit configuration of each divided PSB part is called eXtended System Board
Download Pdf Manuals
Related Search