Fujitsu Siemens Computers P50-2H User's Manual
Contents
1. To completely disconnect the mains voltage remove the power plug from the socket e Lay all cables so that nobody can stand on them or trip over them When attaching the device observe the relevant notes in the Preparing for use chapter e No antenna or data transfer cables should be connected or disconnected during a thunderstorm e Make sure that no objects e g jewellery chains paper clips etc or liquids get inside the device danger of electric shock short circuit e Objects filled with liquids e g vases must not be placed on the device The device is not waterproof Protect the device from spray water rain sea water e In emergencies e g damaged casing elements or cables penetration of liquids or foreign matter switch off the unit disconnect the power plug and contact your sales outlet or our help desk e The device must be disposed of in accordance with the local regulations for disposal of special waste During handling and disposal the safety regulations applicable to fluorescent materials must be observed e Only qualified technicians should repair the device Unauthorised opening and incorrect repair may greatly endanger the user electric shock fire risk e You may set only those resolutions and refresh rates specified in the Technical data chapter Otherwise you may damage your monitor If you are in any doubt contact your sales outlet or our help desk e Use a screen saver with moving image2. 2H P50 2H VESA DDC compatible VGA interface Your plasma TV is equipped with a VESA DDC compatible VGA interface and a DVI D interface VESA DDC Video Electronics Standard Association Display Data Channel is used as the communications interface between the plasma TV and the computer If your computer is equipped with a VESA DDC compatible VGA interface it can automatically read the data for ensuring optimum operation from your plasma TV and select the appropriate settings Preset operating modes PC The following are the most frequently used of the preset operating modes 640 x 350 70 Hz 640 x 480 60 Hz 72 Hz 75 Hz 800 x 600 56 Hz 60 Hz 72 Hz 1024 x 768 60 Hz 70 Hz 75 Hz 1280 x 720 60 Hz 75 Hz 1280 x 768 60 Hz 75 Hz 1280 x 1024 60 Hz not with MYRICA P42 1AH Power consumption To save energy when the device is temporarily not in use the plasma TV can be switched into the standby mode with the remote control POWER button or the STANDBY button Standby mode Device operates normally the screen is dark Power consumption normal 400 W P42 1AH reduced to lt 5 W normal 450 W P42 2H reduced to 3 W normal 500 W P50 2H reduced to 3 W If the device is switched into the standby mode a power consumption of up to 5 W is maintained to enable operation with the remote control To completely switch off the power consumption switch off the device with the ON OFF switch see Sw
3. Israel Italy Jordan Kenia Luxemburg Madeira Malta Marocco Monaco 38 English SECAM PAL EE 8 PR Wem Te 8 Sm B G FM FM Teletext PAL B G B G amp D K Nicam Teletext Nicam Teletext FM FM Teletext Nicam Teletext A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H coms w Gee meme sumes 8G PA w Tes ms 89 9A an Pim H Te Prud mo PR Te Rmea 8 PR Rma OK sw Soa DK SEWIPR Sow ma PR same r PR Sra BG PR FW Test Tee p swm Wee 8 PR Tm United Ava Empates 8G PR O oo Tenna A PR Wem Tes A26361 K1064 Z120 1 M119 edition 2 English 39 MYRICA P42 1AH P42 2H P50 2H Troubleshooting Should an error occur first check the following points If the distortion is still not eliminated the plasma TV should if possible be checked on another signal source and or with another data cable If you are unable to solve the problem please inform our help desk Having this problem No display power indicator does not light Display becomes darker Permanently unlit or lit pixels No picture power indicator glows orange The remote control does not work 40 English Check the following points gt Check whether the power cable of the device is properly plugged in and the ON OFF switch on the back of the device
4. SCART2 e S VIDEO or CVBS AV e Component 1 YPbPr e Component 2 YPbPr e VGA PC e DVI By pressing the INFO button you display the designation of the currently selected signal sources in the upper left corner of the screen A26361 K1064 Z120 1 M119 edition 2 English 31 MYRICA P42 1AH P42 2H P50 2H PIP mode Picture in Picture The plasma TV can also display a sub video signal in addition to the main video signal The sub video signal is shown as a PIP display in a window on the main display The following buttons of the remote control are available for setting the PIP mode gt Press the ON OFF button to activate the PIP mode gt Press the SOURCE button to select the source from which the signal for the PIP display is to come gt Press the SIZE button to set the size of the PIP display gt Press the POSITION button to set the position of the PIP display gt Press the SWAP button to exchange the size and position of the main display with those of the PIP display K Press the POP button to display the main display and the PIP display in the same size next to each other gt Ifa TV signal is displayed in the PIP display you change to the next programme in the programme list with the PR button and to the previous programme in the programme list with the PR button Depending on which source the signal for the main display comes from you can use certain sources for the signal of the PIP display The
5. contact your sales outlet or our help desk Additional information Details of how you set the resolution and refresh rate are provided in the documentation on your screen controller the associated driver software A26361 K1064 Z120 1 M119 edition 2 English 1 MYRICA P42 1AH P42 2H P50 2H Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to text marked with this symbol Failure to observe this warning endangers your life destroys the device or may lead to loss of data i Supplementary information remarks and tips follow this symbol gt Text which follows this symbol describes activities that must be performed in the order shown Quotation marks indicate names of chapters or terms Texts in italics indicate filenames and menu items Important notes In this chapter you will find information regarding safety which is essential to take note of with your plasma TV Avoid still images on the screen for longer periods e g still images from videos sender label etc maximum of 1 hour This pictures may remain visible Also avoid longer operation in a picture mode in which black bars are visible operation in the 4 3 picture format These black bars can also remain visible parties Any tampering with or modification of the product will void the warranty and may T This product from Fujitsu Siemens Computers contains intellectual property
6. following combination options are available to you Signal Main display SV SCART 1 SCART 2 VGA ovi YPbPr PIP display 32 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Technical data ee MYRICA P42 1AH MYRICA P42 2H MYRICA P50 2H Size Size diagonal 42 42 107 cm cm 42 42 107 cm cm 502 502 107 cm cm Visible picture baise cus NM icu NN mm x 532 2 mm naL cii NN mm x 532 2 mm bla ANN 106 5 mm x 622 1 mm Number of pixels 852 x 480 1024 x 768 1366 x 768 HxV Pixel spacing 1 095 mm x 1 110 mm 0 912 mm x 0 693 mm 0 810 mm x 0 810 mm Viewing angle Typical 160 Picture format 16 9 Horizontal frequency 31 15 69 kHz 31 15 82 kHz 31 15 82 kHz Refresh rate 56 85 Hz 56 75 Hz digital 56 75 Hz digital 56 90 Hz analogue 56 90 Hz analogue Maximal resolution 1024 x 768 75 Hz 1280 x 1024 60 Hz 1280 x 1024 60 Hz PC analogue digital analogue digital analogue digital AA Green synchronisation Composite 0 3 Vp p negative Video 0 7 Vp p positive Video signal 0 7 Vp p 75 Ohm Colour system PAL SECAM Sound system BG DK I L HD TV YpbPr DVI 480i p 60 Hz 576i p 50 Hz 720p 50 60 Hz 1080i 50 60 Hz SCART 1 Video input output 1 0 Vp p 75 Ohm Audio input output 0 5 Vms A26361 K1064 Z120 1 M119 edition 2 English 33 MYRICA P42 1AH P42 2H P50 2H TMDS DVI D Power supp
7. item In the individual menus the buttons available to you in each case are shown in the footer gt Mark the option you want to change gt Setthe desired value or activate the desired function gt Press the EXIT button to return to the main menu from a submenu or to exit the OSD menu All changes are stored automatically Description of menus The OSD menu is available in different languages The English menu names are used in the following description default setting Different menus and different options are available to you depending on the set signal source The menus and options not available are not shown in the OSD menu The following main menus are available to you in the OSD menu Picture Here you set the picture mode the colour temperature and the picture format Sound Here you set the sound of your plasma TV Setup Here you set the advanced settings transparency of the OSD menu picture in picture mode child lock etc Time Here you set the various time functions TV Here you start the automatic programme search and adjust the programme settings to meet your needs A26361 K1064 Z120 1 M119 edition 2 English 23 MYRICA P42 1AH P42 2H P50 2H PICTURE menu picture settings gt Press the MENU button to open the OSD menu gt Mark the Picture menu item with the lt 2 gt gt buttons gt Press the MENU button to activate the menu item The buttons available to you for sett
8. list in the order in which they are found However you can change the order of the programmes later A detailed description is provided under Carrying out programme search and Arranging programmes Manual Scan With this function you search for a new programme starting from the frequency of the current channel When the next programme has been found you can select whether or not the programme found is to be added to the programme list To start the search manually press the D button To add the programme found to the programme list press the MENU button If you want to search for additional programmes you must restart the manual search To continue the search press the D button Fine Tune With this function you manually set the frequency of an individual channel The set values remain unchanged until an update is carried out Edit With this function you set the order of the programmes in the programme list and the properties of the individual programme A detailed description is provided under Adjusting programme settings 30 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Display modes Main display mode P Press the SOURCE button on the remote control or the INPUT SELECT button on the underside of the plasma TV to select the source from which the signal for the main display is to come For the main display you can select one of the following signal sources e TV e SCART1 e
9. mark HAR or VDE will appear on the outer sheath e For devices which are mounted on a table type SVT or SJT cable sets may be used For devices which sit on the floor only SJT type cable sets may be used e The cable set must be selected according to the rated current for your device CE marking directives 89 336 EEC Electromagnetic compatibility and 73 23 EEC Low voltage The shipped version of this device complies with the requirements of the EEC C directive MYRICA P42 1AH P42 2H P50 2H Disposal and recycling This device has been manufactured to the highest possible degree from materials which can be recycled or disposed of in a manner that is not environmentally damaging The device may be taken back after use to be recycled provided that it is returned in a condition that is the result of normal use Any components not reclaimed will be disposed of in an environmentally acceptable manner If you have questions on disposal please contact your point of sale our Help Desk or obtain information at www fujitsu siemens com recycling Preparing for use Unpacking and checking the delivery The display surface of the device is sensitive to pressure and scratches Always hold the device by the casing gt Unpack all the individual parts gt Check the delivery for damage incurred during transportation gt Check whether the delivery agrees with the details in the delivery note The complete device package include
10. the device settings with the buttons of the control panel With the buttons on the control panel you can make the following settings directly Selecting picture signal source gt Press the INPUT SELECT button A list of the signal sources is displayed gt Choose the signal source you require using the VOLUME A buttons gt Press the INPUT SELECT button to activate the signal source Adjusting the volume gt Press the VOLUME A button to open the volume menu gt Set the volume as required with the VOLUME A buttons The volume menu automatically disappears again after a short time Changing programme gt Press the VOLUME V button to prepare changing gt Change to the next or previous programme in the programme list with the buttons VOLUME A V 20 English A26361 K1064 Z120 1 M119 edition 2 Remote control ONGAN gt 10 11 13 17 20 ON OFF SOURCE SIZE U lamaz SWAPX PRO A26361 K1064 Z120 1 M119 edition 2 LI L 1 S i j 1 EH d A 0 T v x X x gt 3 Z d G L L C MYRICA P42 1AH P42 2H P50 2H 1 POWER switches the device on or into the standby mode 2 INFO information You display the current settings with this button 3 MUTE switches the sound on and off 4 PICTURE With this button you select the picture mode 5 V SIZE With this button you select the picture format 6 SOURCE With this button you select the signa
11. to change the settings gt Press the MENU button to open the OSD menu Choose the TV menu item using the lt gt button Press the MENU button to activate the menu item Choose the Edit menu item using the lt gt button Y Y Y Y Press the MENU button to activate the menu item N 0 No N O No No No No No The programme list will be displayed with the first 8 programmes found If a programme name was detected during the programme search it will be displayed A26361 K1064 Z120 1 M119 edition 2 English 15 MYRICA P42 1AH P42 2H P50 2H Arranging programmes With the OSD menu you can rearrange the order of the programmes according to your personal preferences Moving programme gt Select the programme you want to move with the buttons C gt lt gt gt Press the INSERT button yellow to mark the programme to be moved gt Select the position at which you want to insert the programme with the buttons C gt lt gt gt Press the INSERT button yellow The programme will be inserted at the selected position Swapping position of two programmes gt Select the programme you want to move with the buttons C gt lt gt gt Press the REPLACE button blue to mark the programme to be swapped gt Mark the programme with which the programme is to be swapped with the buttons C4 lt 5 gt Press the REPLACE button blue The selected programmes swap their positions Changing programme properti
12. to put the plasma TV into operation Use the supplied remote control gt Switch the plasma TV on with the ON OFF switch gt Press the POWER button First the signal source must be set to the TV mode gt Press the SOURCE button gt Choose the TV option using the lt gt button gt Press the MENU button to activate the menu item Then you automatically start the programme search gt Press the MENU button to open the OSD menu gt Choose the TV menu item using the lt gt button 14 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Press the MENU button to activate the menu item T V Auto Scan Manuelles Scan Fine Tune Edit Select the Auto Scan menu item using the lt gt button Press the MENU button to activate the menu item Select your country with the lt gt button Y Y Y Y Press the MENU button to start the programme search Wait until the programme search is completed Then the device shows the first programme found found However you can change the order of the programmes later see Arranging i The programmes will be entered in the programme list in the order in which they are programmes Adjusting programme settings After the programme search you can change various programme settings later e g the order of the programmes in the programme list the programme names or the frequency of a channel The following sections contain a description of how
13. 19 edition 2 MYRICA P42 1AH P42 2H P50 2H Removing the foot when using a wall bracket Before you can use a wall bracket the foot must first be removed The wall bracket is not included in the consignment of the TV The foot is shown as an example in the following illustrations The delivered foot may differ from the illustration gt Carefully lay the plasma TV on a smooth clean work surface with the front facing downward Ask someone to help you T Even small knocks can damage the device Make sure that no objects are lying on the work surface as otherwise the frame or display surface could be damaged gt Remove the four screws 1 that secure the foot to the device gt Pull the foot away from the device Mount the wall bracket as described in the wall bracket documentation A26361 K1064 Z120 1 M119 edition 2 English 7 MYRICA P42 1AH P42 2H P50 2H Installing plasma TV Ventilation To ensure sufficient ventilation the intake and exhaust air openings of the device must never be blocked When installing the TV in niches maintain the minimum distance for sufficient ventilation of the device 10 cm from the side and back 20 cm from the top 8 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Connections on plasma TV T Observe the safety precautions in the Important notes chapter in this operating manual Do not cover the v
14. Contents O 1 Notational Conventions eee eee eee e 2 IVA IOAN NOS CIT DTE EO T NE 2 Sale TOUS So ra teo eb us T EA ove eR to Lid eO UD Od Up Aa 2 Gi cin Inlet ETT 4 PANS DOM e 4 io i e M 4 GE mar a Te eosam CUPRUM aN put peuynawe dake nau SS RURU ao 4 DISDOS al AN GTS VCMT Cpt mee etr cc cT 5 PRE DARING TOP ISG RO rH ME ME 5 Unpacking and checking the delve esse eee eee 5 Prepaid Ze COMM re CHE c A ARS 6 IIS SF UNIG DANS SS RT Ee 6 Replacing s rabia toa 6 Removing the foot when using a wall bracket coooooccccccnoccnnconnconcnnncononnnncnnnonnncrnnonarenos 7 TR Hee t Plasma b E o I 8 Connections on plasma EM sod dd uh do la ea hee re eed aca ad rM UL ata 9 Connecing plasma TY aeneis aae t bua ves at tice daas xa ee iaa Uma ous E came Edu 12 Switching plasma TV OU 2 caduta FE aed icc sio dE ains 13 Switching plasma TV on into standby mode sss sese eee 13 setting language of he OSD Tellus emori eet dido 14 Garmyirng ourprodramine Sestius aeie rk Ca EPUA dU Deva du RA ERU VE FRE HN e WR GANE DECR 14 Adjusting programme Settlrigs 3 id asa true S Ae Padi tees Ya doa E dag 15 Arangino PONES m ET TS o DT 16 Changing programme properties sse eee eee ee t xS ee ee 16 Deleting Progra oreeson cenatmedsustnm nu Rc ev me EA ERARE A REEE EERTE TRE RS 18 Salecting TT TTT ee A dad 18 Gh
15. P50 2H SETUP menu advanced settings gt Press the MENU button to open the OSD menu gt Mark the Setup menu item with the C gt Cx2 buttons gt Press the MENU button to activate the menu item The buttons available to you for setting the options are shown in the menu footer Setup Translucent PIP Advanced Translucent With this function you set the transparency of the OSD menu Possible values Off 1 7 Picture In Picture With this function you switch the PIP mode on or off Possible values On Off When the PIP mode is activated the following options are available Here you set the picture format for the PIP display Resource Here you set which signal source is displayed in the PIP display Picture Swap With this function you exchange the signal sources of the main display and the PIP display Here you set the position of the PIP display A description of the PIP mode is also provided under PIP mode Picture in Picture and Selecting signal source for PIP display A26361 K1064 Z120 1 M119 edition 2 English 27 MYRICA P42 1AH P42 2H P50 2H Advanced Here you configure the advanced settings ID Here you set an ID number for service purposes Possible values 0 99 Burn Protect With this function you can partially prevent still images from burning in Possible values On Off Warning Avoid still images on the screen for longer periods e g still images from videos sender label
16. able TV standard Pal Secam Auto automatically Selecting sound standard gt Select the programme for which you want to set the sound standard with the buttons lt 2 gt e gt Mark the property Sound with the buttons 9 9 gt Select the desired sound standard B G D H L Auto with the buttons C gt Hiding programme in programme list If you want to hide a programme in the programme list SKIP Yes the programme is skipped when you change the programmes with the buttons C gt gt gt Select the programme you want to hide in the programme list with the buttons C40 lt gt gt Press the SKIP button green The selected programme is hidden in the programme list Selecting programme as favourite In the TV mode it is possible to change directly to programmes marked as favourites by pressing the FAVORITE button gt Select the program you want to select as a favourite with the buttons C40 gt Mark the property FAV with the buttons 9 9 gt Select the value Yes with the buttons C gt Cx A26361 K1064 Z120 1 M119 edition 2 English 17 MYRICA P42 1AH P42 2H P50 2H Deleting program K Select the programme you want to delete with the buttons 2 gt lt gt gt Press the ERASE button red The selected programme is deleted from the programme list Selecting signal source Selecting signal source for main display gt Press the SOURCE button in the upper section of the remote co
17. anging POTS O A A dedu A Du vb Led vro 18 Opara oN MM ERE 19 Operating elements on the device lees eene nennen nennen nennen nnne nnn nnns 19 Changing the device settings with the buttons of the control panel suuuussss 20 PRET OLS COMI UL OL Sassi c ty 21 R ETT 22 Buttons for editing programme TISL uu ioco sees 22 SIS eE IM Te T astenia da idad dedican 22 Changing device settings with remote Control ee eee 23 I2escrHIDUOD O MENUS utis a nera 23 PICTURE menus picture Te Suri io E dias 24 SOUND Men sotund selllhgs sii ia a 25 SETUP menu advanced SSUINGS unir A NA 27 TIME menu Tecna a E 29 TV menu programme settings eee eee eee ee ee eee ee eee 30 Display sae CS rr 31 MER Ao AAA PA C 31 PIP mode Picture in PII e ura ollas 32 A26361 K1064 Z120 1 M119 edition 2 English Contents Technical data cansan dae 33 VESA DDC compatible VGA interface see eee eee ee eee 35 Presetoperatiiig modes PO Iii e veo REbEaxU RARE Ai 35 POWGEE COMMS CUO IN e e t Pm 35 Pia OG Ue AA RC EROR HMM M 36 PC Digtal DVD 5s eet re santet oet dose mtattivdedec uds TTT 36 SCAR SAME eem p 37 BV OO atta TE E EO 37 Colour and transmission system by country eee eee ee ee 38 Troubleshooting X E 40 English A26361 K1064 Z120 1 M119 edition 2 Introduction Your new plasma TV MYRICA P42 1AH P42 2H P50 2H possesses a whole range of us
18. current filter from the accessories trade can provide a remedy The picture has shadows or ghost images gt Check the antenna cable Use a directional antenna instead of an omnidirectional antenna The picture shows interference false colours or gt Check whether the plasma TV is set to line and picture shaking the correct TV system PAL or SECAM A26361 K1064 Z120 1 M119 edition 2 English 41 MYRICA P42 1AH P42 2H P50 2H Troubleshooting in PC mode Having this problem Check the following points Message gt Check the setting of the picture signal No Signal Keine Eingabe source gt Check whether the antenna or data cable is correctly connected Message The input signal horizontal frequency and refresh rate at the displayed input does not Out of range correspond to the technical plasma TV data gt Adjust the video frequency range using the computer software see documentation for your computer or your graphics card Picture position is not correct The plasma TV recognises an undefined mode see Preset operating modes PC gt Use the OSD function Geometry Auto to carry out the self adjustment of the plasma TV gt Set the picture position with the OSD menu These functions are only available when PC is selected as the signal source Picture is shaking gt Check whether the data cable for the plasma TV is correctly attached to the monitor port on the computer 42 En
19. eful features and functions e g analogue tuner for VHF UHF and cable programmes connections for SCART video and RGB video and S Video minimal space requirements thanks to slim casing optimum ergonomic characteristics totally distortion free and colour purity right into the corners high degree of brightness and good contrast high resolution for operation on a PC easy to operate remote control convenient operation via integrated OSD On Screen display menu 2 tuner picture in picture picture size changeover full screen panorama zoom 1 and zoom 2 power management for reducing power consumption when the computer is not in use integrated dual channel loudspeakers integrated NICAM IGR sound decoder for stereo and two channel sound automatic switch off function teletext This operating manual contains important information you require to start up and run your device For TV operation with the integrated tuner a terrestrial antenna or a cable connection is required As an alternative a satellite receiver can be connected to one of the SCART jacks When you put the device into operation for the first time you should carry out a programme search see Preparing for use Target group You don t need to be an expert to perform the operations described here Do however read the Important notes chapter in the operating manual of the computer and in this operating manual In the event of any problems occurring please
20. entilation openings of the monitor Never open the housing of the power supply unit There is extreme danger from an electrical shock with the housing open There are no components requiring cleaning or repairs in the interior RS 232 port B lt SCART2 port Full DVI port 9 S VIDEO port AUDIO ports LINE 10 AV ports OUT PC IN port VGA 11 AV ports IN COMPONENT ports 2x 12 ON OFF switch 6 Loudspeaker ports 13 Antenna port SCART1 port Half 14 Power connector The following devices can be connected to this plasma TV RS 232 Serial port black For customer service e g for updating the firmware DVI IN Connection for digital video input signals white e g a PC with a digital output DVI D or for HDTV devices AUDIO IN Connection for audio input signals LINE IN white left e g fora PC or for HDTV devices red right A26361 K1064 Z120 1 M119 edition 2 English 9 COMPONENT 1 COMPONENT 2 Y green Pb blue Pr red AUDIO white left red right SPEAKER red right black right black left red left SCART 1 Half SCART 2 Full MYRICA P42 1AH P42 2H P50 2H Connection for analogue VGA input signals e g for a PC with an analogue output D SUB Connections for component video and audio input signals e g for HDTV decoder HDTV video recorder or HDTV player Connection terminals for external loudspeakers Connection for AV CVBS and audio
21. es You can change the following properties of a programme e Change the programme name displayed in the programme list e Set the channel of a programme e Select or automatically assign a different TV standard e Select the sound standard e Hide a programme in the programme list e Select a programme as a favourite i All changes are stored automatically Changing programme name Five characters are available for the programme name gt Select the programme for which you want to set the name with the buttons Z gt Cx gt Mark the position for the character you want to change under Name with the buttons 9 9 gt Select the desired character at this position with the buttons lt 2 gt Cx5 Repeat this procedure until you have entered the desired programme name 16 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Setting channel of a programme This function is used when a programme is transmitted on a new station frequency gt Select the programme for which you want to set another channel with the buttons C gt Cx2 gt Mark the property CH with the buttons 4 9 gt Select the desired channel with the C gt lt gt buttons Selecting TV standard gt Select the programme for which you want to set the TV standard with the buttons C gt gt gt Mark the property Picture with the buttons 4 9 K Select the desired TV standard with the buttons gt lt gt or assign the suit
22. etc maximum of 1 hour Burn Clear With this function you can regenerate burned in areas of the screen in some cases Possible values On Off Blue Back With this function the screen background is shown in blue when there is no input signal Possible values On Off Language With this function you set the language of the OSD menu Possible values English German French Spanish Italian Portuguese Dutch not with MYRICA P42 1AH Child Lock With this function you switch the child lock on or off When the child lock is activated it is not possible to operate the plasma TV with the operating buttons on the device Possible values On Off 28 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H TIME menu time settings gt Press the MENU button to open the OSD menu gt Mark the Time menu item with the C2 Cx buttons gt Press the MENU button to activate the menu item The buttons available to you for setting the options are shown in the menu footer MYRICA P42 1AH MYRICA P42 2H P50 2H Time Time Set Time Set pp On Time E On Time On Channel On Channel On Volume On Volume Off Time j Of Time Sleep Sleep Time Set With this button you set the current time Format Hour Minute With MYRICA P42 1AH AM before 12 00 noon PM after 12 00 noon On Time With this function you set the time at which the device is to be automatica
23. glish A26361 K1064 Z120 1 M119 edition 2
24. ing the options are shown in the menu footer Picture Mode Standard Temperature Normal Video NR ON Screen Form 16 9 With this function you set the picture mode The contrast brightness colour and focus of the picture are set to optimum values depending on the picture mode Possible values Standard Vivid Mild User After the User option is selected a further submenu appears With this function you reset all parameters of this menu to the factory settings Temperature With this button you set the colour temperature Possible values Cool2 Cooll Normal Warml Warm2 Video NR With this function you switch the picture correction Noise Reduction on or off Possible values On Off Screen form With this function you set the picture format Possible values 716 9 PANORAMA ZOOMI ZOOM2 4 3 24 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Geometry With these functions you set the position and the synchronisation of the in PC mode only picture display To set the picture display first use the Auto function and correct the picture display and if necessary then with the other functions These functions are only available when PC is selected as the signal source H Position With this function you set the horizontal picture position With this function you set the vertical picture position Phase With this function you fine tune your display to eliminate picture
25. input signals e g for satellite receiver DVD player video recorder decoders or a gaming console Connection for AV CVBS RGB and audio input signals e g for satellite receiver DVD player video recorder camcorder or a gaming console A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H S VIDEO IN Connection for S VIDEO input signals e g for DVD player video recorder or film camera with S Video connection AV Connections for video and audio input signals VIDEO e g for DVD player video recorder film camera with video yellow port or gaming console AUDIO white left red right TV ANT antenna cable port AC INPUT Connector for the power cable A26361 K1064 Z120 1 M119 edition 2 English 11 MYRICA P42 1AH P42 2H P50 2H Connecting plasma TV Connecting antenna K Connect an antenna cable to the antenna connection of the plasma TV and to the TV antenna socket Connecting the power supply gt Plug the power cable supplied into the power connector of the plasma TV You will find the power connector on the back of the plasma TV gt Connect the connector of the power cable supplied into a properly earthed mains outlet and ensure a secure connection 12 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Switching plasma TV on off gt Press the ON OFF switch at the left on the back of the plasma TV Switching plasma TV o
26. interference Auto With this function you optimally set the picture display automatically SOUND menu sound settings gt Press the MENU button to open the OSD menu gt Mark the SOUND menu item with the C gt Cx2 buttons gt Press the MENU button to activate the menu item The buttons available to you for setting the options are shown in the menu footer Sound Balance DES Sound Mode Standard Spatial Effect ON AVC ON INTERNAL ON MTS STEREO Balance With this function you set the balance between the left and the right loudspeaker Sound Mode With this function you activate the sound mode The bass level and frequency of the sound are automatically set to optimum values depending on the sound mode Possible values Standard Movie Music User Spatial Effect With this function you switch the Surround sound mode on or off Possible values On Off A26361 K1064 Z120 1 M119 edition 2 English 25 MYRICA P42 1AH P42 2H P50 2H Automatic Volume Control With this function you switch the automatic volume control on or off Possible values On Off Intern With this function you change from the internal loudspeakers to the external ones and vice versa Possible values On Off Multi Tone System With this function you set the audio channel Possible values Mono Stereo Language A Language B Language AB 26 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H
27. is switched on The phosphorous illumination has a limited lifetime If your screen display should become too dark it will have to be exchanged gt Please contact our help desk The standard of production techniques today cannot guarantee an absolutely fault free screen display A few isolated constant lit or unlit pixels may be present The maximum permissible number of this kind of defective pixels is dependent on the resolution 6L 10D 10T L light D dark T total Switch on the plasma TV on the device or with the remote control Check the setting of the picture signal source Check whether the batteries in the remote control are still sufficiently charged Make sure that the sensor for the remote control on the plasma TV is not exposed to strong light A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H MEME in TV mode Having this problem this problem Check the Check the following points points No sound gt Check the volume setting gt Check whether the device is muted No picture only static gt Check that the antenna cable is correctly connected Reception may be poor The picture is fuzzy gt Check that the antenna cable is correctly connected Reception may be poor The picture has dark interference lines and a There may be an interference signal on the strong humming sound can be heard antenna cable gt Have the installation checked A sheath
28. itching plasma TV on off A26361 K1064 Z120 1 M119 edition 2 English 35 MYRICA P42 1AH P42 2H P50 2H PC Analogue D SUB eo parres Vs input blue 4 Eh Ls em e L6 ReWkessh vme LES 7 Green video earth 1 DDC Clock 18 dl Blue video earth PC Digital DVI D 1 1 17 s TOS Date KH 1 TMDS Data2 10 TMDS Data1 TMDS Data0 3 TMDS Data 2 4 11 TMDS Data 1 3 19 TMDS Data 0 5 Shield Shield Shield pe Analogue Vertical Hot Plug Detect TMDS Clock Sync 36 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H SCART Half Full 20 18 167 14 71277107876774772 E Jee E ll El ll El ll ee 5 1 D o 19 17 15 13 11 9 7 o ereen can e Souma 0n 12 Blanking eann Not used with SCART Half TV Out for SCART Half current picture signal for SCART Full S Video A26361 K1064 Z120 1 M119 edition 2 English 37 MYRICA P42 1AH P42 2H P50 2H Colour and transmission system by country ra m we See B G PAL Albania Wm wo PR O O 8 amp 8 9R Azores Bahrain Belgium Bulgaria Canary Islands Czech Republic Denmark Egypt Faroe Islands DK Finland France Germany Gibraltar Greece Hungary Iceland Iran Ireland
29. l source 7 SOUND With this function you activate the sound mode 8 S MODE You select the audio channel with this button 9 STILL With this button you stop the displayed picture still image or switch back into the normal playback mode again 10 DIGEST With this button you display the programme overview of all channels 11 Pre PR Changes back to the programme previously set 12 SLEEP Sleep timer By pressing this button several times you set the time after which the device is automatically switched off 13 TEXT Switches Teletext on or off 14 EXIT Closes the submenu or the OSD menu 15 PR A Changes the main display to the next programme in the programme list 16 MENU Opens the OSD menu 17 VOL 4 Decrease volume 18 VOL gt Increase volume 19 PR V Changes the main display to the previous programme in the programme list 20 0 9 With this button you select the programme directly English 21 MYRICA P42 1AH P42 2H P50 2H Teletext With button 13 you switch Teletext on or off With the buttons 21 23 24 and 25 you navigate in the Teletext function 2 picTURE vsizt SOURCE N l l Buttons for editing programme list The detailed description of editing the programme list is provided under Adjusting programme settings 21 ERASE red Deletes the selected programme from the programme list 23 SKIP green The marked programme is skipped whe
30. lly switched on Format Hour Minute To activate the function set the selection to On after setting the time To deactivate the function set the selection to Off after setting the time On Channel With this function you set the program to be displayed after automatic switch on With this function you set the volume to be used after automatic switch on Off Time With this function you set the time at which the device is to be switched off automatically Format Hour Minute To activate the function set the selection to On after setting the time To deactivate the function set the selection to Off after setting the time Sleep With this function you set the number of minutes after which the device is automatically switched off Possible values Off 10 20 30 60 90 120 180 A26361 K1064 Z120 1 M119 edition 2 English 29 MYRICA P42 1AH P42 2H P50 2H TV menu programme settings gt Press the MENU button to open the OSD menu gt Mark the TV menu item with the gt lt gt buttons gt Press the MENU button to activate the menu item The buttons available to you for setting the options are shown in the menu footer TV Auto Scan Manuelles Scan Fine Tune Edit Auto Scan With this function you start the automatic programme search The automatic programme search must be carried out when you want to use your plasma TV for the first time following installation The programmes will be entered in the programme
31. ly AC 100 240 V 50 60 Hz 100 240 V 50 60 Hz 100 240 V 50 60 Hz 1 8A 240 V 2 0A 240V 5 0A 240V 4 4 A 100 V 4 5 A 100 V 2 0A 100V Power consumption Typical 380 W Typical 420 W Typical 500 W Standby 5 W Standby lt 5 W Standby 3 W MEE MYRICA P42 1AH MYRICA P42 2H MYRICA P50 2H p 0 LC 0000 Dimensions Width x Depth x 1037 x 94 x 635 mm 1037 x 94 x 635 mm 1208 x 94 x 723 mm Height without foot without foot without foot 1037 x 240 x 703 mm 1037 x 240 x 703 mm 1037 x 360 x 775 mm with foot with foot with foot Weight approx 41 kg approx 41 kg approx 54 kg packed approx 48 kg packed approx 48 kg packed approx 62 kg Audio input DVI PC Video 1 RCA connection L R 0 5 Vms S Video Component1 2 SCART 1 SCART 2 0 5 Vms at 1 kHz approx 2 x 8 W 8 Ohm LIUC NM NN EMC TV mode EN55020 class B EN 55013 EN 61000 3 2 3 see CE PC mode EN55022 class B EN 55024 EN 61000 3 2 3 see CE Environment Condensation must be avoided Temperature Operating 15 to 35 C Storage 15 to 60 C Change 1 5 C minute maximum Humidity Operation 20 85 without condensation R Pressure Operation 800 1 114 hPa height 0 2000 m Storage 600 1 114 hPa height 0 4500 m Accessories Manual remote control battery Power supply cable 1 8 m Foot with mounting screws 34 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42
32. n changing programmes with the buttons PR A and PR V 24 INSERT yellow Moves programme see Arranging programmes 25 REPLACE blue Exchanges programmes see Arranging programmes Jj Souno SMODE STILL 22 FAVORITE Switches over to the programme set as a favourite 26 No function PIP Picture in Picture 27 ON OFF Activates the PIP mode 28 SOURCE Press this button to select the signal source for the PIP mode 29 SIZE Press this button to select the picture format for the PIP mode 30 POSITION Press this button to change the position of the PIP window 31 SWAP The displays of the main and the PIP window are exchanged 32 PR Changes to the next programme of the programme list in the PIP window 33 PR Changes to the previous programme of the programme list in the PIP window 34 POP Main display and PIP window are shown in the same size next to each other y E 1 La i 2 x E 4 x 3 5 H g A 5 C 4 4 zx E E E 22 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Changing device settings with remote control You can open and operate the integrated OSD On Screen Display menu with the remote control To set the OSD menu perform the following steps gt Press the MENU button to open the OSD menu gt Mark the desired menu item with the lt 2 gt lt gt buttons gt Press the MENU button to activate a menu
33. n into standby mode K Press the Standby button at the right on the underside of the plasma TV From the indicator at the lower right on the front of the plasma TV you can recognise whether the device is in operation in the standby mode or switched off Green The device is switched on Red Dark The device is in standby mode The device is switched off A26361 K1064 Z120 1 M119 edition 2 English 13 MYRICA P42 1AH P42 2H P50 2H Setting language of the OSD menu After switching on the device set the language of the OSD On Screen Display menu according to your needs English is the set as the default setting If you want to use a different language change this setting with the OSD menu gt Switch the plasma TV on with the ON OFF switch Press the POWER button Press the MENU button to open the OSD menu Choose the Setup menu item using the lt gt button Y Y Y Y Press the MENU button to activate the menu item Setup Translucent PIP Advanced Choose the Advanced menu item using the lt gt button Press the MENU button to activate the menu item Choose the Language menu item using the lt gt button Press the MENU button to activate the menu item Select the language to be shown in the OSD menu with the buttons C40 Cx2 Press the Menu button The OSD menu will be changed over to the selected language Y Y Y Y Y Y Carrying out programme search A programme search must be carried out
34. ntrol gt Choose the signal source you require using the lt gt button gt Press the MENU button to activate your selection Selecting signal source for PIP display gt Press the ON OFF button to activate the PIP mode gt Press the SOURCE button in the lower section of the remote control in the PIP field gt Choose the signal source you require using the lt gt button gt Press the MENU button to activate your selection Changing programme gt Press the gt button to change to the next programme in the programme list K Press the lt gt button to change to the previous programme in the programme list 18 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H Operation Controls are provided on the device and the remote control for operating the plasma TV Operating elements on the device The operating controls of the plasma TV are located in the underside of the device With these buttons you can operate the basic functions of the plasma TV A co HEMENS INPUT SELECT jVOLUME 1 INPUT SELECT button SOURCE 3 7 ON OFF switch for the standby mode for selecting the video input source 4 Indicator 2 VOLUME buttons volume 5 Infrared receiver The VOLUME A button opens the menu for setting the volume With the VOLUME Y button you can change the programme in the TV mode A26361 K1064 Z120 1 M119 edition 2 English 19 MYRICA P42 1AH P42 2H P50 2H Changing
35. of third lead to legal prosecution to the full extent of the law Safety notes This device meets the relevant safety requirements for audio video and TV devices If you have any questions contact your sales outlet or our help desk e The display surface of the plasma TV is sensitive to pressure and scratches You should therefore be careful with the display surface so as to avoid lasting damage Newton rings scratches e If the device is brought into the installation site from a cold environment condensation can form Before operating the device wait until it is absolutely dry and has reached approximately the same temperature as the installation site e During installation and before operating the device please observe the instructions on environmental conditions in the Technical data chapter as well as the instructions in the Preparing for use chapter 2 English A26361 K1064 Z120 1 M119 edition 2 MYRICA P42 1AH P42 2H P50 2H e To ensure sufficient ventilation the intake and exhaust air openings of the device must never be blocked e The device automatically sets itself to the correct voltage within the range from 100 V to 240 V Ensure that the local mains voltage lies within these limits e This device may only be connected to a grounded socket e Ensure that the power socket on the device or the earthed mains outlet is freely accessible e The ON OFF switch does not disconnect the device from the mains voltage
36. s one plasma TV one power cable one remote control two batteries type AAA one Warranty Booklet one Getting Started manual two volumes this operating manual two volumes Should you discover that the delivery does not correspond to the delivery note notify your local sales outlet immediately We recommend that you keep the original packaging material Keep it for future transportation A26361 K1064 Z120 1 M119 edition 2 English 5 MYRICA P42 1AH P42 2H P50 2H Preparing remove control Inserting batteries Open the back cover of the remote control by sliding it in the direction of the arrow Place the batteries supplied in the battery compartment Ensure correct polarity Close the battery compartment by sliding the cover back on until you hear and feel it click into place Remove the batteries when not using the remote control for longer periods Handle the remote control with care Do not drop the remote control on the floor Do not expose the remote control to moisture direct sunlight or high temperatures Replacing batteries gt When the batteries are used up indicator no longer lights up replace them with two batteries of the same type type AAA accumulators must be disposed of in accordance with local regulations concerning special i Do not throw batteries or accumulators into the household waste Batteries or waste 6 English A26361 K1064 Z120 1 M1
37. s in PC mode and activate the power management for your monitor to prevent still images from burning in e Keep this operating manual together with your device If you pass on the device to third parties you should include this manual A26361 K1064 Z120 1 M119 edition 2 English 3 MYRICA P42 1AH P42 2H P50 2H Cleaning e Remove the power plug before cleaning the device e Do not clean any interior parts yourself leave this job to a service technician e Do not use any cleaning agents that contain abrasives or may corrode plastic e Ensure that no liquid will run into the system e Ensure that the ventilation areas of the device are free e The display surface of the device is sensitive to pressure and scratches Clean it only using a soft slightly moistened cloth Wipe the device casing with a dry cloth If the monitor is particularly dirty use a cloth which has been moistened in mild domestic detergent and then carefully wrung out Transport e Transport the device with care and only in its original packaging or another corresponding packaging to protect it from knocks and jolts e Never drop the device danger of glass breakage Power cable To guarantee safe operation use the cable supplied Use the following guidelines if it is necessary to replace the original cable set e The female male receptacles of the cord set must meet IEC60320 CEE 22 requirements e The cable has to be HAR certified or VDE certified The
Download Pdf Manuals
Related Search