Ez Access Mobility Aid ez-access User's Manual
Contents
1. So that no sharp edges are exposed install protective caps over side rail corners as shown in FIG 18 Place one cap on each side at both the top and bottom of ramp NOTE If necessary use silicone adhesive to bond cap to ramp y Ne xiv Attach support tube bracket to the center saddle bracket using nylock nuts and washers FIG 19 a TO ensure plumb support tubes level the support tube brackets FIG 20 b Secure and tighten the nylock nuts c Start two each x bolts without washers into the threaded holes on each support tube bracket DO NOT TIGHTEN 3 8 FLAT WASHER FI G 1 9 3 8 NYLOCK NUT SUPPORT TUBE BRACKET LEVEL SUPPORT TUBE BRACKET FIG 20 CENTER SADDLE BRACKET 4 PRE ASSEMBLE HANDRAILS A One pair of handrails is required for each ramp section Handrails are interchangeable B When used in a multiple ramp run joiner assemblies are used to connect handrails together Refer to FIG 24 for following steps i One end of the handrail tube is notched to accept the joiner assembly Locate the notched end on each upper and lower handrail tube ii Slide joiner assembly into the notched end of handrail tube Repeat process for both upper and lower handrail tube Slide the next handrail section over the joiner assembly Ensure that the tube ends are pushed firmly towards each other Using the supplied 5 32 allen wrench tighten setscrews in both joiner2. LOOPS Purchaser to pay for all shipping charges Government purchases exempt DISCLAIMER THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF INSTALLING END CAPS ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STATUTORY INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OPTIONAL INSIDE CORNER HANDRAIL KIT STATUTORY OR OTHERWISE HOWEVER THAT IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD THE DURATION OF SUCH IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE LIMITED WARRANTY DESCRIBED IN THE FIRST PARAGRAPH CORNER POCKET PROTECTIVE CAP MANUFACTURER SHALL NOT BE LIABLE UNDER ANY CONTRACT NEGLIGENCE STRICT LIABILITY OR OPTIONAL HANDRAIL CLOSURE KIT OTHER LEGAL OR EQUITABLE THEORY FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE MISUSE OR INABILITY TO USE THE EQUIPMENT OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPLACEMENT OF THE DEFECTIVE OR NON CONFORMING EQUIPMENT OR OPTIONAL LIGHTNING ROD GROUNDING KIT PART THE MAXIMUM LIABILITY OF MANUFACTURER UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE EQUIPMENT COVERED BY THE WARRANTY OPTIONAL HURRICANE TIE DOWN KIT Some states do not allow the exclusion or limitation of incidental
3. OBSTACLE NEEDS TO BE REMOVED TWO ABLE BODIED PERSONS NEEDED FOR INSTALLATION v v v v v v v v v v v v v v v v v VIEW PACKING LIST Each ramp system is shipped with a packing list Be sure to check that all items and tools are present before starting installation 15 FINAL CHECKS A Ensure that all fasteners are in place and secure Walk on the assembled system checking for any undue movement Remove any debris and metal chips Ensure that the level and slope has not shifted during installation Check that all handrail ends are covered either with loops or with end caps F CONGRATULATIONS Your EZ ACCESS Modular Ramp System is assembled 16 PERIODIC MAINTENANCE AND SAFETY Caution should be used at all times Proper maintenance and upkeep to the ramp surface is vital IMPORTANT USE ONLY WITH A QUALIFIED HELPER Always use your lap belt It is important that you refer to your equipment s Owner Guide for the proper degree of incline decline and chair direction before attempting ramp use Never exceed its recommendations Periodically check and tighten any loose fasteners to ensure safety At all times keep the ramp clear of dirt leaves and other debris that may accumulate on the surface Simply sweeping the ramp or using a garden hose will usually suffice but if needed a damp cloth or soft brush with soap and water can be used avoid alkaloid detergents Rinse well and use extra caution when the r
4. assemblies Join all handrails together in this manner 4 JOINER ASSEMBLY FIG 24 gt NOTCHED HANDRAIL TUBE 2 ANCHOR TOP TRANSITION PLATE The top transition plate must be anchored to a substantial surface to assure the ramp will not be dislodged Use the pre drilled holes at Place a base foot under each support tube bracket then slide support tube each corner of the top transition plate as guides through the bracket and onto the base foot FIG 21 A IF RESTING ON A WOODEN SURFACE a NOTE If used on very soft soil it may be necessary to set the base foot on i Drill two holes into the wooden surface and secure by installing a 10 x a concrete pad 17 stainless screw and 10 stainless washer into each hole FIG 23 Adjust the legs one at a time B IF RESTING ON A CONCRETE SURFACE 7 a Raise the ramp sections at the center saddle bracket to take any i Using a marker transfer the hole locations from the top transition plate to sag out of the ramp run Using a 5 16 masonry bit drill two 172 deep holes at the marked surface c Place end cap on support tube FIG 21 Lightly set lead concrete anchor into holes with a hammer NOTE Adjusting sections can be accomplished by having someone Re attach the top transition plate and align over the drilled holes sight down the ramp while another person adjusts the ramp height Secure the top transition plate by installing a 10 x 1 stainless screw and IMPORT
5. can be installed To account for obstacles either position can be used as long as one platform saddle bracket is installed in each corner Position the platform saddle bracket over the threaded inserts located on each outside corner of the platform FIG 4 Slide the platform saddle brackets into position one end of the bracket will slide into the groove NOTE If there are space limitations the saddle brackets can be installed under the platform as shown in FIG 7 if necessary support tubes can be cut to fit Using a socket wrench attach a platform saddle bracket to the platform with two 5 16 x 17 bolts and two 5 16 flat washers DO NOT OVER TIGHTEN FIG 5 Repeat this step for all four platform saddle brackets NOTE The 4x 4 5 x4 and 5 x 5 platforms each use 4 four platform saddle brackets Once installed start two each x bolts into the threaded holes in each platform saddle bracket FIG 6 in order to secure the support tube PLATFORM PLATFORM SADDLE BRACKET PLATFORM SADDLE BRACKET 3 8 x 1 2 BOLTS RAMP HANDRAIL c CONNECTING TWO PLATFORMS TOGETHER i Place the surface of the platform face down onto cardboard or a lawn so that the platform is not damaged scratched or dented Places edges to be joined against one another Attach platform connector saddle bracket two each into existing threaded inserts using 5 16 x 1 hex bolts four per bracket and 5 16 flat washers
6. four per bracket as shown in FIG 8 DO NOT OVER TIGHTEN NOTE Any two platforms with the same width can be connected However generally two 5 x 4 platforms are connected to make a turn back platform FIG 9 shows completed assembly CAUTION Although platforms are now connected four support tubes must be installed per platform 5 16 X 1 1 2 HEX BOLT 5 16 FLATWASHER MEASURE GAPS CUT AND INSTALL TUBES 11 INSTALL OPTIONAL HANDRAIL CLOSURE KIT A This kit will connect the handrails on a platform to the handrails on one side of the ramp i If needed drop square tube post into corner pocket on platform and tighten two set screws with supplied 3 16 allen wrench FIG 33 D ATTACH SUPPORT TUBES TO PLATFORM SADDLE BRACKETS i Using an adjustable elbow with a threaded insert in one end pass 5 16 x i Tip the platform on its side Have one person support the platform while the 2 buttonhead screw through the hole in square tube into threaded insert on other person slides the support tubes into the platform saddle brackets adjustable elbow Tighten lightly FIG 34 Adjust the support tubes to the approximate height needed FIG 10 Insert ring joiner into each end of other elbows FIG 35 Insert ring joiner adjustable elbow assembly into tube end on ramp handrail and position both assemblies until they are aligned FIG 36 Measure the distance between the ring portions of the ring jo
7. two interchangeable center saddle brackets per joint The center saddle brackets are also where the handrails and support tube brackets are attached and are a part of the ramp support assembly FIG 14 ft 5 16 x 1 1 2 BOLT x 5 16 x 1 1 2 FLAT WASHER Attach the center saddle brackets using four each 5 16 x 1 bolts and washers per center saddle bracket Tighten all eight bolts four each per center saddle bracket NOTE A maximum of three ramp sections may be joined in this manner If necessary install optional top support assembly at this time See OPTIONAL TOP SUPPORT ASSEMBLY RAMP HANDRAIL lt Y K INSTALL PLATFORM HANDRAILS END BRACKET S RAMP HANDRAIL NOTE Depending on your configuration refer to FIG 26 and 27 as needed END BRACKET i Drop platform handrails into corner pockets on straight platform configuration NOTE If the handrails do not fit it may be necessary to remove the washers between the vertical post and round tubes To connect handrails on turn and turn back platform configurations remove one vertical post per platform and retain for reuse Pass three each 5 16 x 2 buttonhead screws through the holes in square post and into threaded insert in round tube square tube end Tighten with supplied 3 16 allen FIG 15a wrench If the handrails do not fit in the corner pocket it may be necessary 1 to remove add washers between the vertical post and round tubes Tighten t
8. vi Using a metal file smooth any sharp edges from the cutting Adjust the final height of the platform vi Insert cut tube into place and tighten all set screws on ring joiner adjustable a Adjust each leg one at a time by loosening the bolt in the platform elbows assemblies PG 32 dala bracket Using a level adiuct the clatter heiahtand NOTE If difficult to install disassemble adjustable elbows and reconfigure as ae tre A alg 10 INSTALL CORNER POCKET PROTECTIVE CAP retighten FIG 12 A A Some platform configurations will have unused corner pockets on which corner Once the final height has been adjusted tighten the second bolt in each pocket protective cap will need to be installed FIG 32a platform saddle bracket Ensure that all bolts are secure CUT TO FIT SUPPORT F INSTALL PLATFORM BRACE ASSEMBLY i Install platform brace assemblies on all support tubes when the walking surface is 36 or more above the ground The platform brace assemblies are normally installed on all four sides FIG 13 Platform brace assemblies need to be cut to desired length and 5 16 holes to attach the brace bands will need to be drilled at both cut ends Ensure that all platform brace assemblies are secured before using platform 7 INSTALL LOOPS A Install loops using same procedure as handrail with joiner assemblies 8 INSTALL END CAPS A Use end caps when there are any remaining open ends on the handrails i P
9. ANT Ensure that the ramp sections are parallel to each 10 stainless washer into each hole other If they are not it may be difficult to install the handrails c IF RESTING ON AN ALUMINUM PLATFORM l Double check that all bolts are tight the support tubes are plumb and i Drill two 1 holes and secure by installing a 10 x 1 stainless screw and the ramp sections are aligned parallel to one another 10 stainless washer into each hole NOTE If the hole you are drilling is not coming out between two ribs on the underside of the platform drill a new hole through the top transition plate and platform in a position that will allow the screws to be installed between the ribs FIG 23 BASE FOOT 3 ANCHOR BOTTOM TRANSITION PLATE A Ifthe bottom transition plate end of ramp system is resting at ground level then anchoring the ramp is optional B Ifa bottom transition plate is resting on any type of raised area i e a platform it must be anchored using the same procedures as used to ANCHOR TOP TRANSITION PLATE If the ramp tread surface is over 36 in height connect the brace assembly under the ramp as shown in FIG 22 The brace assembly ends will need to be cut to desired length and 5 16 holes to attach the brace bands will need to be drilled at both cut ends Ensure that all platform brace assemblies are secured before using platform FIG 16 H INSTALLING A SINGLE RAMP RUN Tu
10. OD A as shown in FIG 44 is to be used for securing platforms only The Tie Down Installation Kit meets the requirements of Section 6 0 of ASCE 7 02 wind loads for ensuring that all EZ ACCESS Ramp systems are properly restrained against hurricane strength winds Install the EZ ACCESS Modular ramp system ramp system to establish layout and locations It may be necessary to temporarily reposition components in order to install anchor augers WARNING Prior to installing the anchor augers into the ground ensure that any underground electrical conductors natural gas lines water drain lines and or other l PLATFORM CONNECTOR KIT interferences are located and will not hinder the installation WARNING The tie down installation should be completely inspected for any loose wire ropes fasteners anchor augers etc after being subjected to strong winds HANDRAIL CLOSURE KIT BRIDGE PLATE RA i AVAILABLE LENGTHS 12 THROUGH 144 ptt tt tt tt dd dt S 12 INCREMENTS PRIMARY TIE DOWN LOCATIONS SECONDARY TIE DOWN LOCATIONS a SUPPORT TUBES PAIR HANDRAIL END CAP ITEMS NOT SHOWN ACTUAL SIZE 1 INSTALLING PLATFORMS If your system does not include a platform skip to INSTALL RAMP SECTIONS of this instruction guide Generally we suggest installing all platforms and ramps before installing handrails see HANDRAIL INSTALLATION A There are three types of platforms you may be in
11. Patent Pending L L A WA LU Q O Z O lt lt H v lt Proudly made in the USA be shared modified distributed reproduced or reused without i Products Inc a division of Homecare Please visit www ezaccess com or contact us at 1 800 451 1903 f EZ Recess d 6421 REV A 05 21 09 nt are proprietary and ma ss written permission o Thank you for choosing EZ ACCESS Modular Ramps for all of your ramping needs 2003 2009 HOMECARE PRODUCTS INC All rights reserve INSTALLATION GUIDE FOR EZ ACCESS MODULAR RAMP SYSTEMS ATTENTION INSTALLER e 850 lb weight capacity e Read all instructions including PERIODIC MAINTENANCE AND SAFETY prior to ramp assembly e Please leave INSTALLATION GUIDE with the end user ATTENTION END USER e 850 lb weight capacity e Please read and become familiar with the PERIODIC MAINTENANCE AND SAFETY section of this manual e Fill out and return warranty information TOOLS TYPICALLY REQUIRED V Y2 SOCKET OR 2 WRENCH 9 46 SOCKET OR 9 46 WRENCH 5 46 DRILL BIT IF BRACE ASSEMBLIES ARE USED Ys DRILL BIT 5 16 MASONRY DRILL BIT USED WHEN INSTALLING TO CONCRETE PORCH STEP ETC 5 32 ALLEN WRENCH SUPPLIED AS NEEDED 3 46 ALLEN WRENCH SUPPLIED AS NEEDED 2 PHILLIPS HEAD SCREW DRIVER BOX KNIFE 25 TAPE MEASURE HAMMER LEVEL RUBBER MALLET FILE POWER DRILL HACKSAW FOR OPTIONAL HANDRAIL KITS DIGGING TOOLS IF AN
12. SINGLE RAMP RUN will make the repair or replacement of defective components at its own expense If Purchaser discovers a defect he she must call Manufacturer at 253 249 1101 to request a Return Authorization RA to return the merchandise to Manufacturer ANCHOR TOP TRANSITION PLATE If Manufacturer determines in its sole discretion to replace the equipment with either a new or repaired unit ANCHOR BOTTOM TRANSITION PLATE purchaser shall be responsible for a charge prorated on the following basis The purchaser will be allowed a credit against the purchase price of equivalent equipment at the time of return to Manufacturer in proportion 3 to the percentage of the warranted service life remaining at the time of such return Purchaser will be PREAS EMPLEFANDRALS responsible to pay the balance of the purchase price of equivalent equipment Manufacturer reserves the right to require payment prior to delivery of the repaired replaced equipment In calculating available credit INSTALLING RAMP HANDRAILS the remaining warranted service life will be rounded up or down to the nearest whole year YEARS 0 1 Unit repaired or replaced YEARS 1 2 Repair or 50 credit current purchase price multiplied by credit INSTALLING PLATFORM HANDRAILS percentage YEARS 2 3 Repair or 25 credit current purchase price multiplied by credit percentage This limited warranty does not cover removal or reinstallation Manufacturer reserves the right to require INSTALLING
13. amp When used the top support assembly replaces the Ramp Handrail End Brackets i Attach top support brackets with two each 5 16 x 174 bolts and two each 5 16 flat washers NOTE There is a left and right top support bracket The two 3 8 studs aligned horizontally should be toward the end of the ramp FIG 39 B The following steps are done AFTER the ramp is resting on a supporting surface and the top transition plate is installed IMPORTANT Read INSTALLING A SINGLE RAMP and ANCHOR TOP TRANSITION PLATE sections and ensure all steps are completed before proceeding with the steps that follow i Install support tube bracket on each top ramp support bracket using two each 3 8 nylock nuts into the threaded holes and two each 3 8 flat washers DO NOT TIGHTEN FIG 40 Install two each 3 8 x 2 hex bolts into the threaded holes on the support tube bracket Slide support tube into support tube bracket and onto base foot Level support tube and then tighten 3 8 nylock nuts to secure support tube bracket FIG 41 Adjust height as needed and then tighten bolts Place end caps on support tube B INST i ii ALL SADDLE BRACKETS TO PLATFORM Place the surface of the platform face down onto cardboard or a lawn so that the platform is not damaged scratched or dented Each platform has two different configurations at each corner into which the platform saddle brackets and support legs
14. amp surface is wet If ramp surface is covered with ice and or snow remove before use Snow accumulation should be shoveled and the tread surface swept clean Calcium Chloride salt substitute may be used to melt snow or ice accumulation on the ramp however after the snow and or ice threat has cleared be sure to clean the tread surface with soap and water avoid alkaloid detergents to remove Calcium Chloride residue Rinse well and use extra caution when the ramp surface is wet Do not play on or near ramp Do not use handrails or ramp to support planters decorations etc Ramp surface may become slippery when wet If any part of the ramp is damaged or loose DO NOT USE UNTIL REPAIRS CAN BE MADE BY A CERTIFIED INSTALLER OR OTHER QUALIFIED PERSON WARRANTY REGISTRATION EZ ACCESS A DIVISION OF HOMECARE PRODUCTS INC e 700 MILWAUKEE AVE N ALGONA WA 98001 7408 TYPE EZ ACCESS MODULAR RAMP MANUFACTURED DATE NAME PHONE ADDRESS CITY ST ZIP NAME OF DEALER DEALER S CITY ST ZIP PRICE DATE PURCHASED WHERE WILL RAMP BE USED WHAT INFLUENCED YOUR PURCHASE OF THIS RAMP L FRIEND RECOMMENDED L DEALER RECOMMENDED L WEBSITE L ADVERTISING MAGAZINE Q OTHER PLEASE EXPLAIN Please mail warranty information within 10 days of purchase CONTENTS BASIC SYSTEM COMPONENTS WARRANTY amp REGISTRATION INSTALLING PLATFORMS EZ ACCESS a division of Homecare Products Inc herein re
15. ferred to as Manufacturer warrants that the INSTALL SADDLE BRACKETS TO PLATFORM equipment shall be free from defects in material and workmanship under normal use and service for a period of 3 years from the date of original purchase This limited warranty applies to the original purchaser CONNECTING TWO PLATFORMS TOGETHER only and is non transferable This limited warranty is applicable to defective metal structure components only excludes powder coated finish applied non skid tread etc No part of this warranty will apply to any ATTACH SUPPORT TUBES TO PLATFORM SADDLE BRACKETS equipment which has been subject to misuse vandalism negligence alteration improper loads accident improper installation or which has been repaired outside Manufacturer s place of business in any way as in INSTALL BASE FEET AND ADJUST HEIGHT the reasonable judgment of Manufacturer to adversely affect its performance and reliability nor to normal deterioration due to wear tear and exposure corrosion or damage caused by rain fire earthquake or other natural causes or acts of nature INSTALL PLATFORM BRACE ASSEMBLY Manufacturer s obligation and purchaser s sole remedy under this warranty is limited to at Manufacturer s INSTALL RAMP SECTIONS option repairing or replacing equipment which is returned to its place of business and which upon examination shall disclose to Manufacturer s reasonable satisfaction to have been defective Manufacturer INSTALLING A
16. iner assemblies HELPFUL HINT Use the supplied 5 32 and 3 16 allen wrenches to lightly tighten the ring joiner adjustable elbow assembly so they hold their position while measuring vi Cut round tube to the length measured FIG 37 vii Using a metal file smooth any sharp edges from the cutting vii Insert cut tube into place and tighten all setscrews on ring joiners and adjustable elbows FIG 38 NOTE If difficult to install disassemble adjustable elbows FIG 33 FIG 34 ADJUSTABLE ELBOW WITH THREADED INSERT FIG 10 Using a 9 16 socket wrench secure each of the support tubes with one of the two bolts on each platform saddle bracket the second bolt will be tightened after final height adjustments are complete The universal platform configured as a turn back platform FIG 3 will have eight tubes to adjust CAUTION Do not attempt to walk on the platform without both bolts in each platform saddle bracket tightened securely Place the platform with support tubes attached into the upright position IMPORTANT Do not let the weight of the platform bear on the support tubes while tipping the platform upright as it may bend the outer rail E INSTALL BASE FEET AND ADJUST HEIGHT i Slip the base foot under each support tube FIG 11 NOTE If installing on soft soil it may be necessary to set the base foot on a concrete pad or stepping stone v Cut round tube to the length measured FIG 31
17. is the smaller l BUTTONHEAD SCREW of the two into what will be the upper end of the ramp NOTE When used with an MTSA the bottom transition plate the larger of the two can be installed at what will be the upper end of the ramp to compensate for minor angular misalignment about 10 degrees between the porch deck or platform Install the bottom transition plate larger of the two into what will be the lower end of the ramp FIG 16 TIGHTEN lt SET SCREWS TRANSITION PLATE FIG 26 FIG 27 a Maneuver the ramp to its desired position FIG 17 IMPORTANT Make sure the top transition plate overlaps the supporting surface as far as possible 5 INSTALL HANDRAILS l l A Install pre assembled handrail section to side of ramp run FIG 22 CAUTION DO NOT use the ramp until all support tubes and ramp brace i The vertical posts of the handrails each have two holes that correspond assemblies if needed are installed and secured with studs on the saddle brackets that were installed earlier ii Attach handrails to these studs using two each 5 16 flat washers and two each 5 16 hex nuts per handrail post NOTE If the studs do not align with the posts and are off by 6 the Ramp Handrail End Bracket was installed into the wrong threaded insert on the ramp See FIG 15a for location of the correct insert 5 16 NUTS NOTE Make sure that the top transition plate overlaps the supporting surface as far as possible
18. or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also WARRANTY have other rights which may vary from State to State Manufacturer reserves the right to change or improve its products without any obligation to change or improve any Product previously manufactured by it FINAL CHECKS OPTIONAL TOP SUPPORT ASSEMBLY PERIODIC MAINTENANCE amp SAFETY BASIC SYSTEM COMPONENTS Because each ramp configuration will differ from one another your system may or may not contain all of these basic system components METHOD A TO BE USED ON PLATFORMS ONLY FIG 44 ae ad MODULAR RAMP WITH HANDRAIL MODULAR RAMP WITHOUT HANDRAILS NOTE SUPPORT TUBES AND BASE FEET NOT INCLUDED A RAMP i Refer to FIG 44 METHOD B ii Install one TIE DOWN KIT per each 10 feet of ramp e g 8 of ramp requires one TIE DOWN KIT but 12 of ramp requires two See FIG 43 ETT for acceptable locations l iii Drill a 5 16 hole below the tread surface and between the ribs underneath NOTE SUPPORT TUBES AND NOTE SUPPORT the treads in each of the side rails at the center of the ramp BASE FEET NOT INCLUDED TUBES AND BASE RAMP CONTAINS 1 BRACE f FEET NOT i In this drilled hole install one of the 5 16 eyebolts and secure to the ramp PLATFORMS CONTAIN 4 EACH P ERER using one 5 16 flat washer and one 5 16 nut d Install the tie down anchor augers into
19. rn the ramp section upside down on a flat surface Do this on cardboard or a lawn so that the ramp is not damaged scratched or dented Install four ramp handrail end brackets these will be used to attach handrails in a later step i ii RAMP HANDRAIL END BRACKET a For 4 6 and 8 ramps use one at each outside corner of the ramp section using one 5 16 x 1 bolt amp washer into the threaded insert second from the end of the ramp FIG 15a For 10 ramps two additional ramp handrail end brackets are installed using one 5 16 x 1 bolt and washer at the center of each ramp section FIG 15b NOTE Ensure holes in ramp handrail end bracket align with threaded inserts in ramp Install one fastener into either of the two inserts FIG 17 RAMP HANDRAIL END BRACKET FIG 15b Turn the ramp over to the upright position a Place the upper end of the ramp onto the supporting surface i e platform porch etc Once the ramp is resting on the porch or platform lift the upper end of the ramp and install the top transition plate into what will be the upper end of the ramp and the bottom transition plate into what will be the lower end of the ramp FIG 16 NOTE The bottom transition plate is the larger of the two a Maneuver the ramp to its desired position FIG 17 TRANSITION PLATE NOTE Make sure that the top transition plate overlaps the supporting surface as far as possible
20. stalling one or more of these types All three require the same procedure for assembly except for FIG 3 which requires an additional platform connector kit FIG 1 5 x 5 Universal Platform straight configuration FIG 2 5 x 5 Universal Platform turn configuration FIG 3 5 x 4 Universal Platform 2 shown combined to make 5 x 8 turn back platform 13 INSTALL OPTIONAL LIGHTNING ROD GROUNDING KIT A The Lightning Rod Grounding Kit provides a path for lightning strikes into the ground WARNING Prior to installing the grounding rod ensure that any underground electrical conductors natural gas lines water drain lines and or other interferences are located and will not hinder the installation i Install the EZ ACCESS Modular ramp system ii Drive the grounding rod straight into the ground as close as possible at least within 17 to one of the support tubes leaving approximately 2 exposed Install the hose clamp around support tube Place 8 copper wire under hose clamp and tighten so that wire is in good contact with support tube Install 5 8 grounding rod clamp to grounding rod Place 8 wire between clamp and rod then tighten clamp NO 8 BARE COPPER WIRE SN ae ee SUPPORT TUBE WITH 5 8 DIAMETER gt HOSE CLAMP GROUNDING ROD CLAMP 5 8 DIAMETER GROUNDING ROD 12 INSTALL OPTIONAL TOP SUPPORT ASSEMBLY A The top support assembly provides supplemental support at the upper end of the r
21. the ground inline with the eyebolts and perpendicular to the ramp at an approximate angle of 30 degrees Use a 2 steel rod or similar item through the eye of the anchor auger to turn the anchor auger into the ground Keep turning the auger until only the eye is exposed Secure one end of the wire rope to one of the eyebolts using the supplied 3 16 wire rope clamps Thread the other end of the wire rope through the eye of the anchor auger and secure the wire rope to itself using the supplied 3 16 wire rope clamps NOTE Ensure that the wire rope has been pulled taut and all slack has been removed prior to securing it to the anchor auger vi Cut the excess wire rope as required using a cable cutter or other appropriate tool Wrap vinyl electrical tape at the cut end to keep the wire rope from fraying vii Repeat on the opposite side of ramp section B PLATFORM i Refer to FIG 44 METHOD A ii Install one TIE DOWN KIT per Platform RAMP HANDRAIL END BRACKET PAIR HANDRAIL END LOOPS PAIR ii Install eyebolts by removing the 5 16 x 174 bolt then inserting the eyebolt ITEMS NOT SHOWN ACTUAL SIZE in its place see FIG 43 for acceptable locations TOP SUPPORT ASSEMBLY 14 INSTALL OPTIONAL HURRICANE TIE DOWN KIT The installer based on field conditions will determine the exact location of the tie downs As a rule they should be positioned opposite one another and near the center of ramp as shown in FIG 43 METH
22. ush them in by hand or by using a rubber mallet then twist caps once they are in place 9 INSTALL OPTIONAL INSIDE CORNER HANDRAIL KIT A Because each installation is unique the components must be cut at the job site i Slide a ring joiner into both ends of the adjustable elbow FIG 28 ii Slide a ring joiner adjustable elbow assembly into each ramp handrail tube FIG 29 iii Position both assemblies until they are aligned FIG 30 iv Measure the distance between the two ring portions of the ring joiner adjustable elbow assembly HELPFUL HINT Use the supplied 5 32 and 3 16 allen wrenches to lightly tighten the ring joiner adjustable elbow assembly so they hold their position while measuring RING JOINER f EED NNS HANDRAIL TUBE ie ee ELBOW ZXR a aeS FIG 29 A INSTALL RAMP SECTION S i Turn the ramp sections upside down on a flat surface so that the ramps do not get scratched or dented it is recommended that this be done either on the lawn or on a piece of cardboard NOTE If you are installing a single ramp section skip to INSTALLING A SINGLE RAMP RUN Butt the sections together end to end and ensure there is no gap Position the two center saddle brackets over the threaded inserts found on the end of each ramp section FIG 14 One edge of the center saddle bracket will slide into the groove of the ramp section NOTE Ramp sections are connected to create a ramp run using
23. wo each set screws in each corner pocket on platform with vii Install four ramp handrail end brackets these will be used to attach supplied 3 16 allen wrench handrails in a later step i Use a rubber mallet to install square plastic end caps into the top of a For 4 6 and 8 ramps use one at each outside corner of the handrail posts ramp section using one 5 16 x 1 bolt amp washer into the Install plastic protective cap over unused corner pocket threaded insert second from the end of the ramp FIG 15a i Using the supplied 3 16 allen wrench tighten the setscrews on the outside For 10 ramps two additional ramp handrail end brackets are of the square corner pockets l installed using one 5 16 x 1 bolt and washer at the center of NOTE Straight platform handrails simply drop into the square pockets and each ramp section FIG 15b NOTE Ensure holes in ramp require no assembly other than tightening the set screws FIG 26 handrail end bracket align with threaded inserts in ramp Install one fastener into either of the two inserts Turn the joined ramps to the upright position Place the upper end of the ramp onto the supporting surface i e platform UNIVERSAL PLATFORM UNIVERSAL PLATFORM porch etc STRAIGHT CONFIGURATION TURN CONFIGURATION Once the ramp is resting on the porch or platform lift the upper end of the lt 3 16 ALLEN WRENCH se ramp and install the top transition plate top transition plate
Download Pdf Manuals
Related Search