Dynex DX-TVM111 User's Manual
Contents
1. 3 Tighten the screws until they are snug against the TV bracket Do not over tighten You ll need Screws Washers Space rs a A 9 mR P HIPS Screwariver a E 4 F 4 TV bracket A Installation instructions DX TVM111 11 STEP 6 Mounting the TV to the wall plate e Place the TV bracket A into the slotted flanges of the wall plate B The TV can be mounted either 1 vertically or 2 with a 5 tilt HEAVY You will need assistance with this step 1 Vertical mount Note Attach the TV bracket to the flange that is closest to the wall plate 2 Tilt mount Note Attach the TV bracket to the flange that is farthest from the wall plate 12 DX TVM111 Installation instructions STEP 7 Locking the TV to the wall plate e Slide the locking bar I through the TV bracket A and the wall plate B to secure the TV A padlock not included may be used for extra security Vertical mount Tilt mount You ll need sy Locking bar I Y m Th www dynexproducts com 800 305 2204 Distributed by Best Buy Purchasing LLC 7601 Penn Ave South Richfield MN 55423 U S A 2013 BBY Solutions Inc All rights reserved DYNEX is a trademark of BBY Solutions Inc Registered in some countries All other products and brand names are trademarks of their respective owners 6907 002009 lt 02 gt V1 ENGLISH 12 10552. the mounting screw holes on your TV 5 Identify which type of back your TV may have e Flat back The bracket lays flush against the back of your TV and do not block any jacks You do not need spacers when assembling the wall mount e Obstructed back The bracket blocks one or more of the jacks on the back of your TV You will need spacers when assembling the wall mount Irregularly shaped back There is a gap between the bracket and some part of the back of your TV You will need spacers when assembling the wall mount 6 Remove the TV bracket A 8 DX TVM111 Installation instructions M STEP 4 Select screws washers and spacers 1 Select the hardware for your TV screws washers and spacers A limited number of TVs come with mounting hardware included If there are screws that came with the TV they are almost always in the holes on the back of the TV Select one of the following types of screws M4 x 12 mm screws C for a flat back TV M4 x 30 mm screws D for an irregular or obstructed TV back For an irregular or obstructed TV back use the following spacers Universal spacers F Ad caution To avoid potential personal injuries and property damage make sure that there are adequate threads Screw fits to secure the brackets to your TV If you encounter resistance correctly stop immediately and contact customer service Use the shortest screw and spacer combination to accommodate your TV Using hardware th
3. A TV Bracket 1 B Wall Plate 1 J Wall mount template 1 A B J TV Hardware Bag Label Hardware Qty Label Hardware Qty M4 x 12mm C 4 fjae screw M4 x 30mm D p lt 4 m H 2 E M4 washer 4 F M4 spacers 4 i 1 Locking bar Z 3 tir aliti tated te date dt hidi 1 20 30 40 oil 6 rO BJ H 100mm 4 DX TVM111 Installation instructions O Installation instructions STEP 1 Determine wall mount location Notes e For more detailed information on determining where to drill your holes visit our online height finder at http mf1 bestbuy selectionassistant com index php heightfinder e Your n should be high enough so your eyes are level with the middle of the screen Normally 40 to 60 inches from the ground The center of your TV will match the center of the wall plate B Before you drill holes in the wall 1 Measure the distance from the bottom of your TV to the middle half of the height of the TV This is measurement a 2 Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall Keep in mind that the bottom of the TV should be placed above any furniture such as entertainment centers or TV stands The TV should also be above items placed on top of the furniture like a Blu ray player or cable box This measurement is b 3 Add a b The total measurement is the height where you want the center of the wall plate B to be on the wall 4 Use a pencil to
4. DY NE eee DX TVM111 TV Wall Mount Before using your new product please read these instructions to prevent any damage 2 DX TVM111 Safety information and specifications Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION Do not use this product for any purpose not explicitly specified by Dynex Improper installation may cause property damage or personal injury If you do not understand these directions or have doubts about the safety of the installation contact Customer Service or call a qualified contractor Dynex is not responsible for damage or injury caused by incorrect installation or use The weight of your TV must not exceed 30 Ibs 13 6 kg The wall must be capable of supporting five times the weight of your TV and wall mount combined This product contains small items that could be a choking hazard if swallowed Keep these items away from young children Tools needed You will need the following tools to assemble your new TV wall mount OY Edge to edge stud finder Pencil Phillips screwdriver 1 8 3 mm wood drill bit for wood stud wall Socket wrench with 7 16 11 mm socket or adjustable wrench an 1 2 12 mm masonry drill bit concrete only Tape a Measuring tape Hammer Package contents DX TVM111 3 Package contents Make sure that you have all the hardware necessary to assemble your new TV wall mount
5. at is too long may damage your TV However using a screw that is too short may cause your TV to fall from the mount Screw is Screw is too long too short 2 Remove the screws 3 Fora flat back TV go to STEP 5 Option 1 Attaching the mounting hardware to TVs with a flat back on page 9 OR For an irregular or obstructed back go to STEP 5 Option 2 Attaching the mounting hardware to TVs with irregular or obstructed backs on page 10 Installation instructions DX TVM111 9 STEP 5 Option 1 Attaching the mounting hardware to TVs with a flat back 1 Align the TV bracket A with the screw holes on the back of the TV 2 Install washers E and screws C into the top two holes in the back of the TV NOTE If the hole pattern on your TV is 75 mm x 75 mm do not use the washers E 3 Tighten the screws until they are snug against the TV bracket Do not over tighten You ll need Screws Washers C 4 Phillips screwdriver E 4 TV bracket A 10 DX TVM111 Installation instructions OO STEP 5 Option 2 Attaching the mounting hardware to TVs with irregular or obstructed backs 1 Align the TV bracket A with the screw holes on the back of the TV 2 Place spacers F behind the TV bracket and the washers E over the holes in the TV bracket then insert the screws D through the washers TV bracket and spacers NOTE If the hole pattern on your TV is 75 mm x 75 mm do not use the washers E
6. ight you determined in the previous step and make sure that it is level Tape the wall plate template in position then use a pencil to mark the lag bolt hole locations 2 Remove the wall plate template 2 Drill pilot holes to a depth of 3 in 75 mm using a 1 2 in 12 mm diameter masonry drill bit 3 Insert the concrete wall anchors H into the pilot holes and use a hammer to make sure the anchors are flush with the concrete surface 4 Align the wall plate B with the anchors insert the lag bolts G through the holes in the wall plate then tiqhten the lag bolts only until they are firm against the wall plate CAUTION Avoid potential injuries or property damage DO NOT over tighten the lag bolts G Minimum solid concrete thickness 8 in 203 mm Minimum concrete block size 8 x 8 x 16 in 203 x 203 x 406 mm 3 in 75 mm You ll need ee deee Level a 1 2 masonry oho 7 16 socket wrench Wall plate B Hammer Tape Installation instructions DX TVM111 7 ee STEP 3 Determine whether your TV has a flat irregular or obstructed back 1 Carefully place your TV screen face down on a cushioned clean surface to protect the screen from damages and scratches 2 If your TV has a table top stand attached remove the stand See the documentation that came with your TV for instructions 3 Temporarily lay the TV bracket A on the back of your TV 4 Align the screw holes in the TV bracket with
7. mark this spot on the wall Measuring tape Pencil Installation instructions DX TVM111 5 NN STEP 2 Option 1 Installing on a wood stud wall Note Any wallboard or material covering the wall must not exceed 5 8 16 mm 1 Locate the stud Verify the center of the stud with an edge to edge stud finder 2 Align the wall plate template J at the height you determined in the previous step and make sure that it is level Tape the wall plate template in position then use a pencil to mark the lag bolt hole locations 2 Remove the wall plate template 3 Drill pilot holes to a depth of 3 in 75 mm using a 1 8 3 mm wood drill bit 4 Align the wall plate B with the pilot holes insert the lag bolts G through the holes in the wall plate then tighten the lag bolts only until they are firm against the arm assembly CAUTION Avoid potential injuries or property damage DO NOT over tighten the lag bolts G Minimum wood stud size common 2 x 4 in 51 x 102 mm nominal 11 2 x 31 2 in 38 x 89 mm You ll need wa Edge to edge ake drill bit ie e stud finder 7 Level Wall plate B Template J 6 DX TVM111 Installation instructions STEP 2 Option 2 Installing on a solid concrete or concrete block wall CAUTION To prevent property damage or personal injury never drill into mortar between blocks Mount wall plate directly onto the concrete surface 1 Align the wall plate template J at the he
Download Pdf Manuals
Related Search