Dimplex DFB6016 User's Manual
Contents
1. How State and Provincial law apply This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty 18 www dimplex com oe Replacement Parts 30 Log SetAssembly 0438550100RP Heater Motor Assembly 1200W 980RPM 2200490900RP Lower Wire Assy Lampholder 4 Socket 2500190500RP Upper Wire Assy Lampholder 2 Socket 4200090100RP ON OFF SWItCh z diee SA SA 2800070200RP Remote Control Receiver 3 Stage 3000430800RP Remote Control Sender 3 Stage 3000370600RP Flame Speed Controller Board w Potentiometer 3000240100RP Flicker Molor Kit cette e rr ek wee ee 3000240200KIT Light Dimmer Control board with Potentiometer 3000250100RP Cord SOU sis hERD EDEN REA e e ade 4100040500RP ReflectorAssembly 5900080700RP Mirror DFB6016 IA nketa sein 5900300400RP DE3009 bh oh och a PSP DAE 5900300300RP Front Glass 0 00000 WI eee 5900310300RP Flat Black Control Knob 8800000200RP ON OFF Heater Switch 2800070500RP Front Grill Controls Cover 1009070159RP Fireplace Foot 02. A A Manual On Off Switch The fireplace has a manual power On Off switch located on the control panel of the fireplace Toggle the switch to turn the fireplace on and off B Y Light Dimmer Turn the flame brightness control knob to increase or decrease the brightness of the flame and embers 10 www dimplex com Operation C Flame Action Control Turn the flame action control knob to adjust the flame speed control to the desired level D Manual Selection Switch Operates the electric fireplace manually Pressing the switch up position once turns on the electric fireplace and activates Level 1 twice activates Level 2 three times activates Level 3 Pressing the switch down position turns the electric fireplace OFF Level 1 ds The flame effect is turned on and the first red indicator light illuminates Level 2 The flame effect remains on the heater is activated to the low heat setting and the first and second red indicator lights illuminate Level 3 Y The flame effect remains on the heater is set to the high heat setting and all three red indicators illuminate Resetting the Temperature Cutoff Switch Should the heater overheat an automatic cut out will turn the heater off and it will not come back on without being reset It can be reset by switching the Main On Off Switch to Off and waiting five 5 minutes before switching the unit back on
3. warranty period for fireplace surrounds mantels and trims also applies to any implied warranties that may exist under applicable law Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to the purchaser 16 www dimplex com SG Warranty What this limited warranty does not cover This limited warranty does not apply to products that have been repaired except by Dimplex or its authorized service representatives or otherwise altered This limited warranty does further not apply to defects resulting from misuse abuse accident neglect incorrect installation improper maintenance or handling or operation with an incorrect power source What you must do to get service under this limited warranty Defects must be brought to the attention of Dimplex Technical Service by contacting Dimplex at 1 888 DIMPLEX 1 888 346 7539 or 1367 Industrial Road Cambridge Ontario Canada N1R 7G8 Please have proof of purchase catalogue model and serial numbers available when calling Limited warranty service requires a proof of purchase of the product What Dimplex will do in the event of a defect In the event a product or part covered by this limited warranty is proven to be defective in material or workmanship during i the 5 year limited warranty period for products other than fireplace surrounds mantels and trims and ii the 1 year limited warranty peri
4. anniversary of the first purchase and ending at midnight on the fifth anniversary of the date of first purchase this limited warranty entitles the purchaser to replacement parts only without charge If Dimplex is unable to replace such part or if replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of replacement choose to refund the purchase price for such part The 17 Warranty purchaser shall not be entitled to on site or in home warranty services The purchaser shall be responsible for all expenses incurred for the removal of the part and installation of the replacement part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s place of business and all labour costs Such costs shall not be the responsibility of Dimplex Forsurrounds mantels and trims for the period ending at midnight on the first anniversary of the date of first purchase Dimplex will in its sole discretion either repair or replace such defective surrounds mantels and trims or part thereof without charge If Dimplex is unable to repair or replace such product or part or if repair or replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part The purchaser shall not be entitled to on site or in house Services T
5. two 2 bulbs up in behind the grill that illuminate the interior of the fireplace 3 Close the battery cover Oy Battery must be recycled v e or disposed of properly Check with your Local Authority or Retailer for recycling advice in your area Required Tools Phillips 2 screw driver Slot screw driver Approximate time 15 minutes to change upper and lower light bulbs Helpful Hints It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life Group replacement will reduce the number of times you need to open the unit to replace light bulbs To open the light bulb area 1 Remove the trim by turning the retaining fasteners counterclockwise 1 4 turn until the trim releases from 13 oe Maintenance the firebox using a slotted screwdriver Figure 5 Hold the glass in place while removing the retaining clip from the upper center of the firebox Figure 6A B Lift glass out and store in a safe place Lower Light Bulb Requirements Quantity of four 4 clear chandelier or candelabra bulbs with an E 12 small socket base 60 Watt rating To replace the bottom light bulbs 1 Lift up the front edge of the log until it clears the front tabs Pull out until the rear tab clears the back ledge then lift out Figure 7 Examine the bulbs to determine which bulbs require replacement Hold the socket while unscrewing the bulb Hold the sock
6. 0000 eee eee aa 8800090100RP X Dimplex Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 2011 Dimplex North America Limited 19
7. A CAUTION If you need to continuously reset the heater unplug the unit and call Dimplex North America Limited at 1 888 346 7539 Remote Control The fireplace is supplied with a radio frequency remote control This remote control has a range of approximately 50 feet 15 25 m it does not have to be pointed at the fireplace and can pass through most obstacles including walls It is supplied with one of 2 178 independent frequencies to prevent interference with other units The frequency designation is indicated on the back of the transmitter Remote Control Initialization Reprogramming Follow steps 1 through 6 to Operation initialize your fireplace for the first time This procedure is also reguired every time there is a loss of power to the remote control in the fireplace 1 E power failure breaker tripped main power switch is turned off 1 Ensure that power is supplied through the main service panel 2 Access the manual controls remove glass doors or pull grill down if applicable pull the right side steel curtain to the outside of the unit if applicable 3 Locate manual controls 4 Activate main power switch 5 Press and hold the ON switch marked for five 5 seconds red indicator light will flash 6 Press the ON button located on the remote control transmitter This will synchronize the remote control transmitter and receiver Remote Control Usage The remote
8. X Dimplex Better solutions through innovation Owner s Manual Model DF3003 DFB6016 IMPORTANT SAFETY INFORMATION Always read this manual first before attempting to install or use this fireplace For your safety always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage To view the full line of Dimplex products please visit www dimplex com 7205450200R12 Table of Contents Welcome amp Congratulations 3 A IMPORTANT INSTRUCTIONS 4 Site Selection and Preparation 7 C Fireplace Installation 10 M Operation 2424 Cur x ERSTE EA Maca eU a 10 P Maintenance 13 D cur seesi i e eaa e a aaa a aa ase 16 9 Replacement IA oa deh oat A ee 19 Always use a qualified technician 1 NOTE Procedures and or service agency to repair techniques that are this fireplace considered important enough to emphasize amp CAUTION Procedures and techniques which if not carefully followed will result in damage to the equipment WARNING Procedures and techniques which if not carefully followed will expose the user to the risk of fire serious injury or death 2 www dimplex com Welcome amp Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex the world leader in electric fi
9. ce for wiring If you return your existing fireplace to its original use example wood burning it should be inspected by the local building department prior to use to reduce the risk of fire and personal injury New Wall Construction 1 Select a suitable location that is not susceptible to moisture and is away from drapes furniture and high traffic 2 Place the fireplace in the desired location to see how it will look in the room 3 Mark the desired location on the floor and store the fireplace in a safe dry and dust free location 4 Use studs to frame an opening of 30 Ya inch 78 1 cm wide X 25 inch 65 4 www dimplex com Site Selection and Preparation Figure 2 29 8 cy 25 65 4 cm 30 Ya 78 1 cm 11 Ya io cm high X 11 Ya inch 29 8 cm deep Figure 2 Plan your electrical power supply refer to NOTE 1 Option 1 The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace Option 2 A new outlet can be installed inside the new frame construction Dimplex Mantel Surround Kit or Custom Made Mantel Surround 1 Select a suitable location that is not susceptible to moisture and is away from drapes furniture and high traffic Place the fireplace in the desired location to see how it will look in the room For ease of electrical hook up you may wish to locate the fireplace nea
10. control operates the fireplace levels sequentially The level is increased every time the ON button on the transmitter is Figure 4 ON Button OFF Button Battery Battery Cover pressed The fireplace can be turned off at any point by pressing the OFF button on the remote control transmitter Level 1 K The flame effect is turned on and the first red indicator light illuminates Level 2 5 The flame effect remains on the heater is activated to the low heat setting and the first and second red indicator lights illuminate Level 3 D The flame effect remains on the heater is set to the high heat setting and all 12 www dimplex com Operation three red indicators illuminate Battery Replacement Figure 4 To replace the battery 1 Slide battery cover open on the hand held transmitter 2 Correctly install one 1 12 Volt A23 battery in the battery holder I Maintenance amp WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electric shock or damage to persons Light Bulb Replacement Allow at least five 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears There are four 4 bulbs under the log set which generate the flames and embers and
11. et while screwing in the new bulb Replace the log ember bed by placing the back lip of the log ember bed under the mirror then push the front of the log ember bed down into the recess Figure 7 Figure 5 Figure 6 Removing Glass Retaining Holding Clip Glass www dimplex com oe Maintenance Figure 7 Back Ledge Side Section Figure 8 Upper Light Bulb Requirements Quantity of two 2 clear chande lier or candelabra bulbs with an E 12 small socket base 15 Watt rating To replace the top light bulbs 1 Locate the two upper bulbs inside the firebox at the top Figure 8 2 Examine the bulbs to determine which bulbs require replacement 3 Hold the socket while unscrewing the bulb 4 Hold the socket while screwing in the new bulb Glass Cleaning The glass is cleaned in the factory during the assembly operation During shipment installation handling etc the clear door may collect dust particles these can be removed by dusting lightly with a clean dry cloth To remove fingerprints or other marks the clear door can be cleaned with a damp cloth The clear door should be completely dried with a lint free cloth to prevent water spots To prevent scratching do not use abrasive cleaners or spray liquids on the clear door surface Fireplace Surface Cleaning Use a cloth dampened with warm water only
12. he purchaser is responsible for all expenses incurred for repair or replacement of such product or part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or Service agent s business and all labour costs Such costs shall not be the responsibility of Dimplex On site or in home services not provided under this warranty may be performed at the purchaser s specific request and expense at Dimplex s then current rates for such services What Dimplex and its dealers and service agents are also not responsible for IN NO EVENT WILL DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL DIMPLEX OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER
13. ions of the fireplace insert are 30 inch 76 8 cm wide X 25 inch 64 8 cm high X 11 7 inch 29 2 cm deep Figure 1 You should allow 1 4 inch 6 4 mm around the fireplace insert for ease of installation This fireplace does not require any venting amp CAUTION Clearance for air circulation beneath the fireplace insert is provided by four 4 rubber feet Figure 1 Do not install the fireplace insert directly on carpet or similar surfaces which may 7 S Site Selection and Preparation Figure 1 30 Ya 76 8 cm 25 Yo ul 11 yr Rubi er 29 2 cm Air Circulation Areas restrict air circulation If installing the fireplace in a carpeted area place a one piece solid flat surface under the fireplace insert Ensure that all four of the insert s feet rest securely on this surface Existing Fireplace Installation 1 Seal all drafts and vents with non fibrous insulation materials to prevent chimney debris from falling into the fireplace insert Do not install into an existing fireplace that is prone to leaks or dampness 2 Cap the top of the chimney flue to prevent rain from entering 3 Plan your electrical power supply refer to NOTE 1 4 The power cord can run along the front of the hearth to an outlet near the fireplace WARNING To prevent personal injury you should hire a professional to cap the chimney flue or cut a hole in the existing firepla
14. od for surrounds mantels and trims you have the following rights Limited warranty service will be performed solely by dealers or service agents of Dimplex authorized to provide limited warranty services For products other than surrounds mantels and trims for the period ending at midnight on the first anniversary of the date of first purchase Dimplex will in its sole discretion either repair or replace such defective product or part without charge If Dimplex is unable to repair or replace such product or part or if repair or replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part This limited warranty entitles the purchaser to on site or in home warranty services Accordingly Dimplex will be responsible for all labour and transportation costs associated with the repair or replacement of the product or part except as follows i charges may be levied for travel costs incurred to travel to the purchaser s site where the product is located if the purchaser s site is beyond 30 miles 48 km from the closest service depot of Dimplex s dealer or service agent and ii the purchaser is solely responsible for providing clear access to all serviceable parts of the product For products other than surrounds mantels and trims for the period commencing at 12 01 a m on the day after the first
15. r an existing outlet refer to NOTE 1 Store the fireplace in a safe dry and dust free location Assemble the mantel surround kit refer to the mantel assembly instructions or construct the custom surround with an opening of 30 Ya inch 78 1 cm wide X 25 Ya inch 65 4 cm high X 11 Ya inch 29 8 cm deep Figure 2 WARNING Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician Fireplace Installation 1 Make sure the unit s Main On Off switch is switched Off refer to operating instruction section 2 Plug the unit into a 15 Amp 120 Volt outlet If the 4 Level the unit with shims if necessary not provided 5 Install the trim onto the fireplace refer to trim installation instructions cord does not reach you may WARNING Ensure the use an extension cord rated for a minimum of 1875 Watts 3 Push the fireplace into the opening being careful not to damage the base of the mantel or cabinet so that the fireplace is flush with the mantel or cabinet Operation power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons Figure 3 MM P oS 7 oj D R M
16. ration of the device www dimplex com Site Selection and Preparation This section provides easy step by step instructions for selecting a location and preparing the site to install the fireplace into e Existing fireplace e New wall construction e Dimplex mantel surround kit or custom made mantel surround NOTE 1 A 15 Amp 120 Volt circuit is required A dedicated circuit is preferred but not essential in all cases A dedicated circuit will be required if after installation the circuit breaker trips or fuse blows on a regular basis when the heater is operating Additional appliances on the same circuit may exceed the current rating of the circuit breaker WARNING Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire electric shock and injury to persons Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician NOTE The fireplace insert comes completely assembled and wired Some tools may be required to prepare the site and assembly install the trim The dimens
17. replaces Please carefully read and save these instructions amp CAUTION Read all instructions and warnings carefully before starting installation Failure to follow these instructions may result in a possible electric shock fire hazard and will void the warranty Please record your model and serial numbers below for future reference model and serial numbers can be found on the Model and Serial Number Label of your fireplace Model Number g wX M SERIAL No a es ee S Seriaf Number WATTS NATIOL 1 VOLTS VOLTIO 121 STOP NO NEED TO RETURN TO THE STORE Questions with operation or assembly Require Parts Information Product Under Manufacturer s Warranty Contact us at www dimplex com customer support For Troubleshooting and Technical Support s OR WA Toll Free 1 888 DIMPLEX 1 888 346 7539 Monday to Friday 8 00 a m to 4 30 p m EST Please have your model number and product serial number ready See above amp IMPORTANT INSTRUCTIONS When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following D Read all instructions before using this appliance The heater is hot when in use To avoid burns do not let bare skin touch hot surfaces The trim aro
18. sible fire do not block air intake or exhaust in any manner Do not use on soft surfaces like a bed where openings may become blocked 2 All electrical heaters have hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored or where the unit will be exposed to flammable vapours 3 Do not modify the fireplace Use it only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Avoid the use of an extension cord Extension cords may overheat and cause a risk of fire If you must use an extension cord the cord must be No 14 AWG minimum size and rated no less than 1875 Watts 5 Do not burn wood or other materials in the fireplace Do not strike the fireplace glass D Always use a certified electrician should new circuits or outlets be required Always use properly grounded fused and polarized outlets Disconnect all power supply before performing any cleaning maintenance or relocation of the unit When transporting or storing the unit and cord keep in a dry place free from excessive vibration and store so as to avoid damage WARNING To prevent overheating do not cover heater SAVE THESE INSTRUCTIONS amp IMPORTANT INSTRUCTIONS WARNING Remote control contains small batteries Keep away from children If swallowed seek medical atten
19. tion immediately amp WARNING Do not install battery backwards charge put in fire or mix with used or other battery types may explode or leak causing injury NOTE Changes or modifications not expressly approved by the party responsible for compliance could void user s authority to operate the equipment amp CAUTION This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired ope
20. to clean painted surfaces of the electric fireplace Do not use abrasive cleaners 15 SG Warranty Products to which this limited warranty applies This limited warranty applies to the following applicable models of your newly purchased Dimplex electric fireplace DF3003 DFB6016 and to newly purchased Dimplex fireplace surrounds mantels and trims This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory Nunavut or Northwest Territories or in any of the 50 States of the USA and the District of Columbia except for Hawaii and Alaska This limited warranty applies to the original purchaser of the product only and is not transferable Products excluded from this limited warranty Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner purchaser Products purchased in Yukon Territory Nunavut Northwest Territories Hawaii or Alaska are not covered by this limited warranty Products purchased in these States provinces or territories are sold AS IS without warranty or condition of any kind including without limitation any implied warranties or conditions of merchantability or fitness for a particular purpose and the entire risk of as to the quality and performance of the products is with the purchaser and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair What this limited
21. und the heater outlet becomes hot during heater operation Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 feet 0 9m from the front of the unit 3 Extreme caution is necessary when any heater is used by or near children or invalids and whenever the unit is left operating and unattended 4 Always unplug the fireplace when not in use 5 Do not operate any unit with a damaged cord or plug or if the heater has malfunctioned or if the fireplace has been dropped or damaged in any manner Return heater to authorized service facility for examination electrical or mechanical adjustment or repair 6 Do not use outdoors 2 The fireplace is not intended for use in bathrooms laundry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container Do not run the cord under carpeting Do not cover crd with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over 9 To disconnect the unit turn the controls off then remove the plug from the outlet Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NO USER SERVICEABLE PARTS INSIDE www dimplex com amp IMPORTANT INSTRUCTIONS cause an electric shock or fire or damage to the heater To prevent a pos
22. warranty covers and for how long Products other than fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment Subject to the provisions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 5 years from the date of the first purchase of such products as follows a a repair or replacement warranty on defective products or parts including in home services for the first year following the date of first purchase and b thereafter a replacement of parts warranty on defective products and parts with no in home services for the 4 year period commencing on the first anniversary of first purchase and ending on the fifth anniversary of the date of first purchase Dimplex fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment and subject to the provisions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 1 year from the date of first purchase of such products Warranty services do not include in home services The above section is a summary only of your warranty rights Please review the remaining provisions of this warranty for your specific rights The limited 5 year warranty period for products other than fireplace surrounds mantels and trims and the limited 1 year
Download Pdf Manuals
Related Search