Dell PowerConnect W-AP224/225 Installation Manual
Contents
1. ENETO ac a canst itll ee The W AP220 Series access point is equipped with five LEDs that indicate the status of the various components of the AP Table 1 LED Behavior Color State Meaning C External Antenna Connectors ENETO ENET1 The W AP224 access point is equipped with three external antenna connectors The connectors are labeled ANT0 ANT1 and ANT2 and correspond to radio chains 0 1 and 2 Figure 2 Externa Antenna Connectors W AP224 only ANTO ANT1 ANT2 Figure 3 Bottom Panel Console Port Ethernet Ports USB Interface Kensington Lock CONSOLE ENET 1 ENET 0 56V 350mA O D TS DC Power Socket Reset Button USB Interface The W AP220 Series access point is equipped with a USB interface for connectivity with cellular modems Note The USB interface is disabled when the W AP220 Series is powered from K 802 3af PoE Console Port The serial console port allows you to connect the W AP220 Series access point to a serial terminal or a laptop for direct local management This port is an RJ 45 female connector with the pinouts described in Figure Connect it directly to a terminal or terminal server using an Ethernet cable Figure 4 Serial Port Pin Out Serial RJ 45 Female Console Port Pin Out 1 Jk ge bo w 5 GND a RxD 8 Ethernet Ports The W AP220 Series access point is equipped with two 10 100 1000Base T RJ 45 a2. Provisioning parameters are unique to each AP These local AP parameters are initially configured on the controller which are then pushed out to the AP and stored on the AP itself Dell recommends that provisioning settings be configured via the ArubaOS Web UI only Refer to the Dell Networking W Series ArubaOS User Guide for complete details AP Configuration Configuration parameters are network or controller specific and are configured and stored on the controller Network configuration settings are pushed out to the AP s but remain stored on the controller Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI Refer to the Dell Networking W Series ArubaOS User Guide for complete details Product Specifications Electrical e Ethernet m 2x 10 100 1000Base T auto sensing Ethernet RJ 45 Interfaces m MDI MDx IEEE 802 3 10Base T IEEE 802 3u 100Base T IEEE 802 3ab 1000Base T Power over Ethernet IEEE 802 3at compliant 48V DC nominal and 56V DC maximum 350mA see Figure 5 for pin configuration Power m 12 VDC power interface supports powering through an AC to DC power adapter POE support on Ethernet ports 802 3at compliant POE sourcing devices Note If a power adapter other than the one provided by Dell Networks is used in the US or Canada it should be cULus NRTL Listed with an output rated 12 VDC K minimum 1 25A marked LPS or Class 2 and suitable for plugg
3. Dell Networking W AP220 Series Access Point Installation Guide The Dell Networking W AP220 Series W AP224 and W AP225 wireless access point AP supports the IEEE 802 1 lac standard for high performance WLAN The access point uses MIMO Multiple in Multiple out technology and other high throughput mode techniques to deliver high performance 802 1 1n 2 4 GHz and 802 llac 5 GHz functionality while simultaneously supporting existing legacy wireless services The W AP220 Series access point works only in conjunction with a Dell Networking W Series Mobility Controller The W AP220 Series access point provides the following capabilities e Wireless transceiver Protocol independent networking functionality e IEEE 802 1 1a b g n ac operation as a wireless access point IEEE 802 1 1a b g n ac operation as a wireless air monitor e Compatibility with IEEE 802 3at PoE and 802 3af PoE Central management configuration and upgrades with a Dell Controller K Note The W AP220 Series requires W Series ArubaOS 6 3 0 0 or later Package Contents W AP224 or W AP225 Access Point e 9 16 and 15 16 ceiling rail adapters e Installation guide this document Note Inform your supplier if there are any incorrect missing or damaged parts If K possible retain the carton including the original packing materials Use these materials to repack and return the unit to the supplier if needed W AP220 Series Hardware Overview Figure 1 L Ds
4. R TA a hy Ree eR This table shows where these substances may be found in the supply chain of electronic information products as of the date of sale of the enclosed product KSAT RE DORR RMS HAMS CPU te NE TERR NEE IE A E D JEFF OREH A RP ETE h FPE t F EE The Environment Friendly Use Period EFUP for all enclosed products and their parts are per the symbol shown here The Environment Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual European Union RoHS D gt E Q Aruba Networks Inc hereby being the manufacturer of this product declares that all CE Marked Dell wirless controller and access points products are manufactured in accordance to the provisional requirements set forth in the RoHS Directive 2011 65 EC A copy of the Aruba Declaration of Conformity may be obtained upon request from Aruba Networks International Ltd Building 1000 Citygate Mahon Cork Ireland Please include the regulatory model number located on the product s regulatory nameplate with the request Dell Networking W AP220 Series Access Point Installation Guide Contacting Dell Web Site Support Main Website dell com support dell com support manuals Support Website Documentation Website Copyright 2013 Aruba Networks Inc Aruba Networks trademarks include Ce AIFWave Aruba Networks Aruba Wireless Networks the registered Aruba the Mo
5. bile Edge Company logo and Aruba Mobility Management System Dell the DELL logo and PowerConnect are trademarks of Dell Inc All rights reserved Specifications in this manual are subject to change without notice Originated in the USA All other trademarks are the property of their respective owners Open Source Code Certain Aruba products include Open Source software code developed by third parties including software code subject to the GNU General Public License GPL GNU Lesser General Public License LGPL or other Open Source Licenses The Open Source code used can be found at this site http www arubanetworks com open_source Includes software from Litech Systems Design The IF MAP client library copyright 2011 Infoblox Inc All rights reserved This product includes software developed by Lars Fenneberg et al Legal Notice The use of Aruba Networks Inc switching platforms and software by all individuals or corporations to terminate other vendors VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies in full Aruba Networks Inc from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors www dell com Dell Networking W AP220 Series Access Point Installation Guide Part Number 0511327 02 October 2013
6. eflectors interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan Identifying Known RF Absorbers Reflectors Interference Sources Identifying known RF absorbers reflectors and interference sources while in the field during the installation phase is critical Make sure that these sources are taken into consideration when you attach an AP to its fixed location Examples of sources that degrade RF performance include Cement and brick e Objects that contain water e Metal e Microwave ovens e Wireless phones and headsets Installing the AP Note Service to all Dell Networking products should be performed by trained K service personnel only Using the Ceiling Rail Adapter The W AP220 Series access point ships with two ceiling rail adapters for 9 16 and 15 16 ceiling rails Additional wall mount adapters amd ceiling rail adapters for other rail styles are available as accessory kits Caution Make sure the AP fits securely on the ceiling tile rail when hanging the device from the ceiling because poor installation could cause it to fall onto people or equipment 1 Pull the necessary cables through a prepared hole in the ceiling tile near where the AP will be placed 2 Place the adapter against the back of the AP with the adapter at an angle of approximately 30 degrees to the tabs see Figure 6 3 Twist the adapter clockwise until
7. ing into a standard power receptacle in the US and Canada Environmental Operating Temperature 0 C to 50 C 32 F to 122 F m Humidity 5 to 95 non condensing e Storage and transportation m Temperature 40 C to 70 C 40 F to 158 For additional specifications on this product please refer to the data sheet The data sheet can be found at dell com Safety and Regulatory Compliance Dell provides a multi language document that contains country specific restrictions and additional safety and regulatory information for Dell hardware products The Dell Networking W Series Safety Environmental and Regulatory Information document is included with the controller products Regulatory Model Names The following regulatory model names apply to the W AP220 Series access point e W AP224 APIN0224 e W AP225 APIN0225 FCC The device is electronically labeled and the FCC ID is displayed via the WebUI under the About menu Caution RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits This equipment should be installed and operated with a minimum distance of 7 9 inches 20 cm between the radiator and your body for 2 4 GHz and 5 GHz operations This transmitter must not be co located or A operating in conjunction with any other antenna or transmitter When operated in the 5 15 to 5 25 GHz frequency range this device is restricted to indoor use to reduce the poten
8. it snaps into place in the tabs see Figure 6 Figure 6 Attaching the Ceiling Rail Adapter 4 If necessary connect the console cable to the console port on the back of the AP Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30 degree angle to the ceiling tile rail see Figure 7 Make sure that any cable slack is above the ceiling tile 6 Pushing toward the ceiling tile rotate the AP clockwise until the device clicks into place on the ceiling tile rail Figure 7 Mounting the AP 7 On the W AP224 install the external antennas according to the manufacturer s instructions and connect the antennas to the antenna interfaces on the AP Connecting Required Cables Install cables in accordance with all applicable local and national regulations and practices Power Connection The W AP220 Series access point has a single 12V DC power jack socket to support powering through an AC to DC power adapter Note If both POE and DC power are available the AP draws power from the PoE K source Verifying Post Installation Connectivity The integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing successfully see Table 1 Refer to the Dell Networking W Series ArubaOS Quick Start Guide for further details on verifying post installation network connectivity Configuring the W AP220 Series AP Provisioning Reprovisioning
9. n K change the settings For more information about AP configuration refer to the Je Networking W Series ArubaOS Quick Start Guide and Dell Networking W Series Aruba0S User Guide Caution Access points are radio transmission devices and as such are subject to governmental regulation Network administrators responsible for the A N configuration and operation of access points must comply with local broadcast regulations Specifically access points must use channel assignments appropriate to the location in which the access point will be used Verifying Pre Installation Connectivity Before you install APs in a network environment make sure that the APs are able to locate and connect to the controller after power on Specifically you must verify the following conditions When connected to the network each AP is assigned a valid IP address e APs are able to locate the controller Refer to the Dell Networking W Series ArubaOS Quick Start Guide for instructions on locating and connecting to the controller Identifying Specific Installation Locations You can mount the W AP220 Series access point on a wall or on the ceiling Use the AP placement map generated by Dell VisualRF Plan software application to determine the proper installation location s Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference These RF absorbers r
10. noise emissions as set out in the interference causing equipment standard entitled Digital Apparatus CES 003 of Industry Canada Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada CE EU Regulatory Conformance Dell hereby declares that this APIN0224 and APIN0225 device models are in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC CE The Declaration of Conformity made under Directive 1999 5 EC is available for viewing at dell com Hong Kong Singapore Complies with ertified for use in Hong Kong ertified for use in Hong Kong IDA Standards AS BR ae O TE BS se FA AG BR ae O TE 2S 5 AA 200202320G Certificate No 2715 Certificate No Bar HK0011300681 HK0011300680 A BASKERA F AERE RA COMMUNICATIONS COMMUNICATIONS SF AUTHORITY SF AUTHORITY TRA TRA REGISTERED No REGISTERED No ER0111798 13 ERO111795 13 DEALER No DEALER No DA0039425 10 DA0039425 10 Medical l Equipment not suitable for use in the presence of flammable mixtures 2 End product system including power supply must be evaluated to IEC 60601 1 1 and IEC 60601 1 by the end user 3 Wipe with a dry cloth no additional maintenance required 4 No serviceable parts the unit must be sent back to the manufacturer for repair 5 No modifications are allowed without Dell approval Proper Disposal of Dell Equipment Dispo
11. nsmit chains disabled The behavior of 5 GHz radio depends on the ArubaOS version running on the access point a 6 3 0 x 2x3 RF chain one transmit chain disabled a 6 3 1 x or later 3x3 RF chain no restrictions Before You Begin Caution FCC Statement Improper termination of access points installed in the United States configured to non US model controllers will be in violation of the FCC grant of equipment authorization Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture 47 CFR 1 80 Caution EU Statement Lower power radio LAN product operating in 2 4 GHz and 5 GHz bands Please refer to the De Networking W Series ArubaOS User Guide for details on restrictions Produit r seau local radio basse puissance operant dans la bande fr quence 2 4 GHz et 5 GHz Merci de vous referrer au De Networking W Series ArubaOS User Guide pour les details des restrictions Low Power FunkLAN Produkt das im 2 4 GHz und im 5 GHz Band arbeitet Weitere Informationen bezl glich Einschr nkungen finden Sie im De Networking W Series ArubaOS User Guide Apparati Radio LAN a bassa Potenza operanti a 2 4 GHz e 5 GHz Fare riferimento alla De Networking W Series ArubaOS User Guide per avere informazioni detagliate sulle restrizioni Pre Installation Network Requirements After WLAN planning is complete and the appropriate products and
12. se of Dell products per local regulations For the most current information about Global Environmental Compliance and Dell products visit dell com Waste of Electrical and Electronic Equipment Dell products at end of life are subject to separate collection and treatment in the EU Member States Norway and Switzerland and therefore are marked with the symbol shown at the left crossed out wheelie bin The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002 96EC on Waste of Electrical and Electronic Equipment WEEE China RoHS O Dell products also comply with China environmental declaration requirements and are labeled with the EFUP 10 label shown at the left ASA EDA H Hazardous Materials Declaration AEG BRICK Hazardous Substance AOE ERKA m RM cr PBB PBDE BS He PCA Boards PLR FE Mechanical Sub Assemblies O RHBARATSRLARA ASRS FHS RAE S T11363 2006 FRAME RRR Indicates that the concentration of the hazardous substance in all homogencous materials in the parts is below the relevant threshold of the J T11363 2006 standard RAGHEB BS DER RSS oS JT 1363 2006 Ss AEE PY BE BER Indicates that the concentration of the hazardous substance of at least one of all homogencous materials in the parts is above the relevant threshold of the J T11363 2006 standard SH FRAT ah AS HE
13. their placement have been determined the Dell controller s must be installed and initial setup performed before the Dell APs are deployed For initial setup of the controller refer to the Dell Networking W Series ArubaOS Quick Start Guide for the software version installed on your controller AP Pre Installation Checklist Before installing your W AP220 Series access point ensure that you have the following CAT5e or CAT6 UTP cable of required length e One of the following power sources IEEE 802 3at or 802 3af compliant Power over Ethernet PoE source The POE source can be any power source equipment PSE controller or midspan PSE device a Dell AP AC DC adapter kit sold separately e Dell Controller provisioned on the network a Layer 2 3 network connectivity to your access point One of the following network services Aruba Discovery Protocol ADP e DNS server with an A record e DHCP Server with vendor specific options Summary of the Setup Process Successful setup of an W AP220 Series access point consists of five tasks which must be performed in this order l Verify pre installation connectivity Identify the specific installation location for each AP Install each AP Verify post installation connectivity Configure each AP WA BR WW N Note Dell in compliance with governmental requirements has designed the W AP220 Series access points so that only authorized network administrators ca
14. tial for harmful interference with co channel Mobile Satellite Systems FCC Class B Part 15 This device complies with Part 15 of the Federal Communications Commission FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation Caution Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instructions may cause interference harmful to radio communications If this equipment does cause interference which can be determined by turning the equipment off and on the user 1s encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or TV technician for help Complies with the Class B limits for radio
15. uto sensing MDI MDX wired network connectivity port These ports support IEEE 802 3af and 802 3at Power over Ethernet PoE compliance accepting 48 VDC nominal as a standard defined Powered Device PD from a Power Sourcing Equipment PSE such as a PoE midspan injector or network infrastructure that supports PoE Note When operating on 802 3af only the port connected to power is K usable For example if the power source is connected to ENET 0 then ENET 1 will not work The 10 100 1000 Mbps Ethernet ports are on the bottom of the AP These ports have RJ 45 female connectors with the pin outs shown in Figure 5 Figure 5 Gigabit Ethernet Port Pin Out 1000Base T Gigabit RJ 45 Female Signal Name Function Ethernet Port Pin Out BI DA Bi directional pair A POE Negative BI_DA Bi directional pair A POE Negative Bi directional pair C POE Positive Bi directional pair C POE Positive Bl_ DD Bi directional pair D POE Negative BI_DD Bi directional pair D POE Negative 1 y 3 S 3 BI_DB Bi directional pair B POE Positive F 4 BI_DC gt 5 BI_DC aN 6 BI_DB Bi directional pair B POE Positive 7 8 Kensington Lock Slot The W AP220 Series is equipped with a Kensington lock slot for additional security Reset Button The reset button can be used to return the W AP220 Series access point to factory default settings To reset the AP 1 Power off the AP 2 Press and hold the reset button using a small narro
16. w object such as a paperclip 3 Power on the AP without releasing the reset button The power LED will flash within 5 seconds 4 Release the reset button The power LED will flash again within 15 seconds indicating that the reset is completed The AP will now continue to boot with the factory default settings DC Power Socket If PoE is not available an optional Dell AP AC DC adapter kit sold separately can be used to power the W AP220 Series When powered in this way the AP will operate in full power mode Additionally a locally sourced AC to DC adapter or any DC source can be used to power this device as long as it complies with all applicable local regulatory requirements and the DC interface meets the following specifications e 12 VDC 5 18W Center positive 1 7 4 0 mm circular plug 9 5 mm length Power Modes The W AP220 Series access point can operate in two power modes The AP s mode is not configurable and is determined by the AP based on the amount of power available The two modes are e Full Power The AP is receiving power from an 802 3at PoE source or is powered using the optional AC DC adapter kit In this mode all AP functionality is available e PoE Power Saving The AP is receiving power from an 802 3af PoE source In this mode the AP has somewhat reduced functionality the second Ethernet port is disabled the USB port is disabled the AP operates in 1x3 RF chain mode for 2 4 GHz two tra
Download Pdf Manuals
Related Search