Craftsman 315.11099 Operator's Manual
Contents
1. A DO NOT STORE YOUR WORKLIGHT IN A C R A T S M A N DAMP OR WET LOCATION ALSO DO NOT STORE IN LOCATIONS WHERE THE TEM PERATURE MAY REACH OR EXCEED 120 F 1 8 0 Volt el oe sheds vehicles or metal uildings in the summer CORDLESS WORKLIGHT E DONOT PERMIT CHILDREN TO USE WORKLIGHT UNSUPERVISED it is not a toy The temperature of the bulb can become hot I5 Part No 975815 003 Use only with Craftsman battery pack after being on for an extended period of time This hot temperature may cause burn injury if and charger both sold separately iouched Extra bulb included m KEEP WORK AREA CLEAN Cluttered areas i i and benches invite accidents AVOID DANGEROUS ENVIRONMENT E KEEP LIGHT DRY CLEAN AND FREE FROM OIL AND GREASE Always use a clean cloth when cleaning Never use brake fluids gasoline petroleum based products or any strong solvent to clean your light mM STAY ALERT Watch what you are doing and use common sense Do not rush E CHECK DAMAGED PARTS Before further use of this light a part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function A part that is damaged should be properly repaired or replaced IMPORTANT SAFETY RULES FOR BATTERY fi P TOOLS ae E USE ONLY THE CHARGER RECOMMENDED FOR USE WITH YOUR WORKLIGHT Do not aaia a i boor mains ae sand substitute any other charger Use of another TEF De enone SAS S ORS eae charger co2. ACEMENT See Figure 3 When purchasing replacement xenon bulb request recommended part number 981258 001 TO REPLACE BULB E Remove battery pack from worklight E Remove the two screws securing lens cover then remove cover E Remove old bulb from spring E Position new xenon bulb in spring E Replace lens cover and screws E Replace battery pack Note For your convenience a bulb storage area with extra bulb has been provided it is located behind the lens cover See Figure 3 SCREWS LENS COVER Fig 3 To presetve natural resources please recycle or dispose of properly This product contains nickel cadmium batteries Local state or federal laws may prohibit disposal of nickel cadmium batteries in ordinary trash Consult your local waste authority for information regarding available recycling and or disposal options For replacement parts information and ordering cail this toll free number 1 800 366 PART 1 800 366 7278
3. ery pack is secure in light before use A CAUTION When placing battery pack in your light be sure raised rib on battery pack aligns with groove inside light handle and latches snap in place properly Improper assembly of battery pack can cause damage to internal components To remove battery pack locate latches on end of battery pack and depress to release battery pack from your light BATTERY PACK DEPRESS LATCHES TO RELEASE BATTERY PACK 96557 OPERATION SWITCH See Figure 2 To turn your light on and off depress switch trigger SWITCH TRIGGER MULTI POSITION HEAD MULTI POSITION HEAD See Figure 2 Your worklight has the feature of a multi position head that has positive stop clicks at each position Rotate head to the desired position as shown in the arrows in figure 2 SAFETY RULES FOR WORKLIGHTS A WARNING Do not operate flashlight or charger near flammable liquids or in gaseous or explosive atmospheres Internal sparks may ignite fumes A WARNING Lens and bulb become hot during use During or immediately after use don t lay worklight flat on lens surface e Handle worklight with care around any flammable surface If bulb has been lit let worklight coo for several minutes before changing bulb Do not use or permit use of worklight in bed or sleeping bags A burn injury could result Sears Roebuck and Co Hoffman Estates IL 60179 USA 972000 671 5 99 BULB REPL
4. t use charger outdoors Disconnect charger from power supply when not in use SAVE THESE INSTRUCTIONS Review them frequently and use them to instruct others who may use this light If you loan someone this light loan them these instructions also OPERATION CHARGING YOUR WORKLIGHT The battery pack and charger are not included with this worklight They are both sold separately If you decide to purchase a battery pack and charger use battery pack part number 975284 001 and charger part number 975283 001 TO CHARGE BATTERY PACK Charge battery pack only with the charger recom mended Make sure power supply is normal house voltage 120 volts 60 hz AC only Connect charger to power supply Place battery pack in charger then press down on battery pack to be sure contacts on battery pack engage properly with charger contacts Red light should turn on When battery pack is fully charged the red light will turn off and the green light will turn on TO INSTALL REMOVE BATTERY PACK See Figure 1 Use 18 0 volt battery pack part number 975284 001 only Begin with a fully charged battery pack Note After normal usage the battery pack requires 1 hour of recharge time Orient battery pack so that raised rib on battery pack aligns with groove inside worklight Battery pack is designed to fit only one way in light handle Insert battery pack making sure latches on each side of battery pack snap in place and batt
5. tteries plode Also DO NOT dispose of a worn out Other types of batteries may burst causing RULES FOR SAFE OPERATION Continued Do not expose to rain or snow To reduce the risk of damage to charger body and cord pull by charger body rather than cord when disconnecting charger An extension cord should not be used unless absolutely necessary Use of improper extension cord could result in a risk of fire and electric shock If extension cord must be used make sure a That pins on plug of extension cord are the same number size and shape as those of plug on charger b That extension cord is properly wired and in good electrical condition and c That wire size is large enough for AC ampere rating of charger as specified below Cord Length Feet 25 ft 50 ft 100 ft 150 ft Cord Size AWG 16 16 16 14 Note AWG American Wire Gage DO NOT OPERATE CHARGER WITH A DAMAGED CORD OR PLUG If damaged have replaced immediately by a qualified serviceman Do not operate charger if it has received a sharp blow been dropped or otherwise damaged in any way take it to a qualified serviceman Do not disassemble charger take it to a qualified serviceman when service or repair is required Incorrect reassembly may result in a risk of electric shock or fire To reduce the risk of electric shock unplug charger from outlet before attempting any maintenance or cleaning Turning off controls will not reduce this risk Do no
6. uld cause batteries to explode causing possible serious injury RULES FOR SAFE OPERATION E Your battery tool should be charged in a location where the temperature is more than 50 F but READ ALL INSTRUCTIONS ese than TROT E KNOW YOUR WORKLIGHT Read owner s m Under extreme usage or temperature conditions manual carefully Learn its applications and battery leakage may occur If liquid comes in limitations as well as the specific potential contact with your skin wash immediately with hazards related to this light soap and water then neutralize with lemon juice m USE ONLY BATTERY PACK PART NUMBER or vinegar If liquid gets in your eyes flush them 975284 001 WITH YOUR WORKLIGHT Any with clean water for at least 10 minutes then attempt to use another battery pack will cause SEBk MMENHI MINEA BNENIOR damage to your light and could possibly explode m WHEN SERVICING USE ONLY IDENTICAL cause a fire or personal injury CRAFTSMAN REPLACEMENT PARTS m REMOVE BATTERY PACK FROM IMPORTANT SAFETY INSTRUCTIONS FOR WORKLIGHT BEFORE REPLACING BULB OR CHARGER PERFORMING ANY ROUTINE MAINTENANCE m Before using battery charger read ail instructions OR CLEANING and cautionary markings in this manual on E DONOT DISASSEMBLE YOUR LIGHT battery charger and product using battery charger E DO NOT PLACE WORKLIGHT OR BATTERY WARNING To reduce the risk of injury charge PACK NEAR FIRE OR HEAT They may ex only nickel cadmium type rechargeable ba
Download Pdf Manuals
Related Search