Clifford concept 50x User's Manual
Contents
1. Definitions W Digit A digit is defined as any number from 1 to 9 inclusive W Valet code A valet code may be to 3 digits A one digit code X any number between 1 9 A two digit code X Y any number between 11 99 excluding numbers with zeros A three digit code X YZ any number between 111 999 excluding numbers with Zeros Remember no code can have a zero m PlainView switch A rocker switch mounted on the dashboard or console The switch has three positions 1 Latched 2 Center 3 Spring loaded momentary When you press the latched side the switch remains in its pressed position When you press the momentary side the switch bounces back to the center position Entering a digit To enter a digit you tap press and release on the momentary side of the PlainView switch the number of times corresponding to the numeral of the digit to be entered followed by pressing to the latched side then returning the switch to its center position Entering a code If your code has only one digit enter the code as described in Entering a digit If your code has more than one digit just repeat the above for each digit of your code To enable valet mode 1 Turn the ignition switch to its ON position or start the engine 2 Enter your secret valet code on the PlainView switch then return the switch to its center position 3 You now have 5 seconds to press the latched position to enter valet mode The system s LED will glow continual2. To help you count you will hear a chirp each time you press the momentary side 5 Immediately flip the switch to the latched position 6 Enter you new code To enter 31 as your new code you would press the switch in this manner momentary momentary momentary latched you ll hear 3 chirps to confirm the first digit momentary latched 1 chirp to confirm the second digit center 7 Wait 3 seconds until you hear 2 chirps indicating the new code has been accepted Turn off the ignition to exit program mode you ll hear a 3 chirp confirmation 9 VERY IMPORTANT You must immediately test your new secret valet code Turn on the ignition enter your new code then flip the switch to its latched position The LED will illuminate If it does not the new code you programmed and the one you just entered do not match In such a case the system will revert to the previous code oo Keyless entry in valet mode Even if valet mode is enabled you can still remotely control the convenience features For instance simply press button 1 channel 1 as if you were disarming and the doors will unlock indicated by one parking light flash and the interior lights will turn on Press button 1 again and the doors lock confirmed by two flashes You can also use the other channels to activate options such as a remote trunk release or remote engine starting 11 Remote controlled valet mode entry and exit You can even enable or exit valet mode wi
3. disarm with all the indications noted above except for the chirp THE SYSTEM acknowledgments TO REMOTELY Button 2 channel 2 controls an electronic interlock that lets you TURN ON A TIMED separately command two functions with the same channel one ACCESSORY when the system is armed and another when disarmed Pressing button 2 while the alarm is armed will activate the system s timed accessory output for any duration you wish between one second and two minutes the factory setting is 30 seconds see User selectable features on pages 16 20 TO REMOTELY Button 2 channel 2 can control another function when the system OPEN THE TRUNK is disarmed such as an optional remote trunk release Pressing button 2 while the alarm is disarmed will remotely open the trunk TO ACTIVATE Button 4 channel 4 and channels 5 12 see How to use your OTHER OPTIONS keychain remote control on page 6 can activate accessories such REGARDLESS OF as the IntelliStart remote engine starter remote power window ALARM STATE control Concept 50x systems and accessories on your other vehicles etc Anti CodeGrabbing ACG with Random Code Encryption Protects you and your automobile from the most effective and onerous car stealing device ever used by car thieves a code grabber Code grabbers literally record from hundreds of meters away the code sent by your car alarm remote control Then the thief simply plays back the code when you re gone in
4. high see Remote Sensor Adjustments on page 12 Clifford s exclusive FACT feature ensures you ll never experience repeated false alarms If the siren goes off DO NOT remotely disarm allow it to run for the full 30 second siren duration Before sounding the siren a second time the system automatically checks for another activated trigger or sensor to verify that a genuine intrusion is in progress Should the siren sound again you will know for sure that someone is tampering with your vehicle To disable FACT see User selectable features on pages 16 20 SmartPowerUp ll If power is removed SmartPowerUp II ensures the system will automatically restore itself to its previous state when power is restored So if a thief disconnects the power while the system is armed and then restores it in an attempt to start the car the system will re arm and instantly sound the siren while immobilizing the vehicle 14 Smart Self Powered Siren with Unbreachable Digital ComLink This siren has its own built in back up battery so even if a thief cuts all the wires the siren will continue to wail Furthermore this unique Clifford designed and manufactured siren has all these important additional enhancements m Unbreachable Digital ComLink Clifford s ingenious Digital ComLink is a serial communications link that ensures that if the system fuse is pulled or if power to the system is interrupted or if any siren wire is tampered with while the system is
5. on off AutoArm amp Lock on off Sound 2 on off info on page 9 NOTE 2 info on page 12 info on page 11 info on page 16 Add new remote to channel 3 FACT on off Sound 3 on off info on page 9 NOTE 3 info on page 12 NOT USED info on page 16 AutoActivate timed channel 4 accessory Set accessory timer duration f P Mfo on page 9 NOTE upon remote arming on off Isec 2min 30sec Henna t this feature is for installers only info on page 9 NOTE 6 pag Erase all channels QuietChirps on off NOT USED Sound 5 on o info on page 19 NOTE 5 NOT USED info on page 16 info on page 16 Long term chirp silencing on off Seta new secret valet code Sound 6 on off info on page 16 info on page 13 14 NOTE 7 info on page 16 WARNING If you have remote window and sunroof closure DO NOT CHANGE THIS SETTING it requires installer only adjustment Changing the duration may cause damage DO NOT alter the installer only setting in the gray cell There is also an installer only column 5 so if you accidentally select an installer only feature turn off the ignition and start again NOTE 1 Transmit channel 1 or other channel of your choosing of the new m NOTE 7 Immediately flip the switch to its latched position then remote control You will hear one chirp to confirm programming of channel 1 a Enter the new code that you wish to use The system will sound the same NOTE 2 Transmit channel 2 or other channel of your choosing of
6. the key to your system It has Clifford s Anti CodeGrabbing ACG technology for the ultimate protection against code grabbing devices see page 8 You will use your remote to arm and disarm the system lock and unlock the doors enter and exit valet mode engage and disengage the AutoImmobilization circuits and command options such as a remote trunk release power window operation and even remote engine starting How to use your keychain remote control LED indicator pence Your remote control can individually command up to 12 different system functions and options It s like having a TV with 12 channels You change channels functions with your keychain remote control But instead of putting 12 buttons on the remote we made it easy First the button you use the most button 1 to arm disarm lock and unlock is larger than the others Buttons 2 3 and 4 are the smaller buttons to the right below and left of button 1 The LevelShift button on the side of the remote control allows you to select channels 5 12 W Jo transmit either channel 1 2 3 or 4 Just press either button 1 2 3 or 4 For instance to transmit channel 3 press button 3 While you transmit the LED indicator will blink once every second this indicates level 1 W Jo transmit either channel 5 6 7 or 8 Press the LevelShift button once This shifts buttons 1 4 to level 2 channels 5 8 Then press the desired button within the next 7 seconds Fo
7. warranty card for full details W FACT False Alarm Control and Test One of many patented Clifford innovations FACT absolutely positively ends recurring false alarms W A Pair of 4 Button 12 Channel Remote Controls Fingertip command from a distance W Anti CodeGrabbing ACG with Random Code Encryption Today s criminals are shifting from code scanning to a new much more efficient method of electronic thievery code grabbing When you use a car alarm remote control it transmits a digital code to your alarm A thief with a code grabber can record that code right off the air from hundreds of meters away then play it back when you re gone to disarm the alarm and unlock the doors Within seconds your car is just another theft statistic Fortunately Clifford s Anti CodeGrabbing ACG randomly changes the transmitted code every time you press any of the remote control buttons And since these codes are selected by the system s microprocessor from an electronic file containing several trillion codes the remote control NEVER sends the same code twice and the system control unit NEVER accepts the same code twice That makes code grabbing utterly useless against the Clifford Concept 50x W UltraSecure Coded Valet Mode Ensures that no thief can turn off your Concept 50x like they can all other brands of alarms W Remote Controlled Valet Mode Entry and Exit With just a press of a button on your remote control y
8. 0x s arm disarm chirps until you wish to restore them The indicator light flashes will continue to provide visual confirmation of remote controlled arming and disarming See the User selectable features section on pages 16 20 W Remote controlled chirp muting This is especially valuable when parking late at night in a quiet residential area To arm or disarm silently press button 3 on your remote control instead of the usual button 1 W QuiefChirps You can control the volume of the arm and disarm chirps As shipped from the factory your system issues full volume chirp acknowledgments If you prefer you may reduce the chirp volume to a level that is clearly audible yet less obtrusive See the User selectable features section on pages 16 20 W Automatic low battery warning If at any time the siren s back up battery voltage is low or it fails to hold its charge the normal arm and disarm chirps will be automatically muted to alert you of the problem Once the back up battery is charged the chirps will automatically be restored W Noise Abatement Circuitry Automatically limits siren sounding to 2 5 minutes even if a door is left open in the wake of an intrusion attempt 15 User selectable features Your Concept 50x allows you to set many of its features to your own personal preferences Although the system s capabilities are extensive we made the programming procedures very simple to make a change you just flick the PlainView switch a f
9. Armed but the hood or trunk is ajar see Smart AutoTesting on page 13 How to interpret the LED status indicator The LED on your car s dashboard or console will inform you of the system status Off System is disarmed and in normal operating mode On Programming or valet mode Flashing The Autolmmobilizer is engaged and or the system is armed and protecting your vehicle Pause between flashes Either a malfunction see page 13 or an intrusion was attempted see page 8 AutoArming If this feature is enabled and you forget to remotely arm the system will automatically arm itself 30 seconds after you park the vehicle exit and close all the vehicle doors For your convenience if you re open any door s within the 30 second countdown AutoArming will restart from the beginning once all doors are closed Concept 50x has these additional AutoArming features m AutoArming enable disable If you prefer you may deactivate or reactivate the AutoArming feature See User selectable features on pages 16 20 B Visual acknowledgment Five seconds after you exit the vehicle and close all the doors the indicator lights will flash twice to confirm that the AutoArming countdown is progressing Then 25 seconds later the system will AutoArm E AutfoArmm amp Lock To ensure you can t accidentally lock your keys inside the car the system is factory set not to lock the doors upon AutoArming To change th
10. World Class Auto Security Owner s Manual CLIFFORD World Class Auto Security The Concept 50x is covered by one or more of the following Clifford Electronics U S A patents 4 158 874 4 233 642 4 327 444 4 383 242 4 430 685 4 845 464 4 887 064 4 890 108 4 922 224 4 997 053 5 081 667 5 146 215 5 157 375 5 467 070 and other patents pending Table of Contents Standard Features of the Concept 50x oes 2 Your 4 button 12 channel remote controls sn 6 How to use your keychain remote control 2222s 6 What each button channel does s 7 Anti CodeGrabbing ACG with Random Code Encryption ss 8 Smart prior intrusion attempt alert oon 8 How to interpret the chirps and indicator light flashes 9 How to interpret the LED status indicator 2222 sss 9 ZAUTO ATITWEYO 1e oC re eMe ap a d pre doter ie a i c dap a SCC d E e 9 AutoArming enable disable 2 2222 sons 9 Visual acknowledgment hann 9 AUAI E LOCK uvas xAY A RENE MA WR ERE eR te ite A TUR e RU 9 Instant AutoArming BYPASS iv se e ooo o kw ade e Re REA 9 Ultrasecure coded valet mode kt 10 Definiliors i e Arn d ee VRE eta D oec e Cte qb Ro he e ps 10 To enable valet mode uk vu laa Be e UR GS ARA 10 To exit valet mode as Tt goo acd de o Re e oe ues 11 Setting your own secret valet code aaa 11 Keyless entry in valet mode ow os 11 Remote controlled val
11. armed the siren will instantly activate for five minutes However if the system is disarmed and power is interrupted for authorized servicing the siren will remain silent This eliminates the need for a special separate shutoff key common to other battery backed sirens This ingenious Clifford feature guards against any possibility of a thief tampering with the system m Smart charging Other battery backed sirens continually draw charging current from your vehicle s battery In time this can drain the car s battery Clifford s Smart Self Powered Siren only draws charging current while the vehicle s ignition is on i e while you re driving This prevents battery drain m Personalized Siren Sounds Most alarm sirens have a single warble tone A few offer six tone sirens that cannot be adjusted or require destruction of circuit wires to change the sounds the change is permanent and cannot be changed again Your Concept 50x siren is different As shipped from the factory it sounds six different alarm sounds However you may turn any of the six sounds on or off to create a different combination of sound patterns In all there are 64 different combinations You may set your own Personalized Siren Sounds so if you hear a siren at a distance you will know for sure whether or not it is your car See the User selectable features section on pages 16 20 m Long term chirp silencing Whenever you wish you may silence your Concept 5
12. ature Select position this is indicated with 3 chirps If you wait another 60 seconds the system will exit program mode this allows you to make programming changes even while you re driving In Example 2 below you ll learn how easy it is to change the settings of several different features in just one session without having to repeatedly turn the ignition on and off EXAMPLE 2 Turn off AutoLock and AutoUnLock then turn on QuietChirps This time we will change the settings of three different features in just one programming session We will turn off both the AutoLock and AutoUnLock features see page 14 as well as turn on the QuietChirps feature see page 15 Here s all you have to do Enter program mode as previously noted ignition on enter your program mode code press the momentary side until you here a chirp 2 Since AutoLock is in column 2 row 1 of the Table you will have to enter the latched side twice and the momentary side once Therefore move the switch to latched center latched center Wait for the two chirps to confirm the selection of column 2 Within 10 seconds press and release the momentary side of the switch once you will hear a chirp when you press it After a brief pause you ll hear 1 chirp to confirm that AutoLock is now off 3 Since AutoUnLock is in column 2 row 2 and is in the same column as you just entered for AutoLock there is no need in this case to again select column 2 Therefore you ca
13. e ignition the system s built in two point AutoImmobilizer electronically disengages your vehicle s starter motor and electronic fuel pump to ensure against theft of your vehicle The LED Status Indicator will repeatedly flash to indicate that AutoImmobilization has been activated Even if a thief were to cut all the wires or even find the Concept 50x control unit and disconnect it he would still be unable to start the engine Please be aware that unlike AutoArming described above Autolmmobilization occurs regardless of whether you open or close any doors What s more disabling the AutoArming feature has no effect on Autolmmobilization When you remotely disarm your Concept 50x the AutoImmobilization circuits automatically disengage You then have 30 seconds to start the engine or turn the ignition switch to its ON position If more than 30 seconds pass the immobilizer will automatically reactivate This will be visually indicated by the LED repeatedly flashing To disarm the Autolmmobilizer use the remote control to arm and then disarm the system Smart AutoTesting Each time you remotely arm the system it tests all triggers and sensors If the hood or trunk is open the system will immediately alert you with 4 chirps and 4 indicator light flashes instead of the usual 2 and 2 If a door is ajar you will receive the usual 2 chirps and 2 flashes then 5 seconds later 4 chirps and 4 flashes The door ajar warning will not work o
14. em s memory records the identity of the last 8 activated or malfunctioning triggers and sensors which allows your installer to track down any malfunction To identify the triggers and sensors held in memory use the following procedure 1 With the ignition OFF flick the PlainView switch to its latched side 2 Press button 1 to arm the system then again to disarm 3 The LED will blink 1 6 times to indicate the most recently activated point pause blink 1 5 times to indicated the next most recently activated point and so on 4 Write down the number of blinks between pauses and refer to the chart on page 13 AufoLock and AutoUnLock For your safety and that of your passengers the doors automatically lock the instant you turn on the ignition see User selectable features on pages 16 20 When you turn the ignition off AutoUnLock automatically unlocks the doors To suit your preferences you may turn off either or both the AutoLock and or AutoUnLock features There are four possibilities AutoLock on while AutoUnLock is off or vice versa The other two combinations are both AutoLock and AutoUnLock on or both off False Alarm Prevention and FACT False Alarm Control and Test False alarms are usually caused by a car alarm s sensor that either cannot detect the difference between normal environmental conditions and a genuine theft attempt or in the case of your Concept 50x has its sensor sensitivity set too
15. ess of a button on the remote simultaneously arms your system and locks the doors Another press disarms and unlocks m User Selectable AutoLock Automatically locks the doors the instant you turn on the ignition to start the engine E User Selectable AutoUnLock Automatically unlocks the doors when you turn off the engine W Smart Self Powered Siren with Unbreachable Digital ComLink Continuous two way digital communication between the system and the siren assures that if at any time the system fuse is pulled or any siren wire is cut the siren will instantly activate for five minutes Yet when the system is disarmed and power is interrupted the siren will remain silent m Personalized Siren Sounds You may select any combination of 6 different sound patterns for unmistakable recognition from a distance So if you hear a siren at a distance you will know for sure whether or not it is your car m Automatic Low Battery Warning If at any time the siren s back up battery voltage is low or it fails to hold its charge the normal arm and disarm chirps will be muted to alert you of the problem Once the siren s internal back up battery is charged the chirps will automatically be restored W Smart Remote Trunk Release Capability Assures the optional remote trunk release can be activated only if the system is disarmed It also makes sure that the trunk release cannot be remotely activated while driving 3 Standard Features of t
16. et mode entry and exit s 12 Remote controlled sensor adjustment 2222s 12 Remote controlled override of one or both sensorzones i 12 Built In Two Point Autolmmobilizer s 13 Smart AUtolesting 3 3 v usc aeg ox eg es 13 Specific malfunction identification aaa a a 13 Automatic malfunction bypass i n 14 Multiple event TotalRecall 60 n 14 AutoLock and AutoUnLOCk aon 14 False Alarm Prevention and FACT False Alarm Control and Test 14 SmatrfPowerUp Il S ee ak Me ob la od Sut dh wok UA dE aa fers 8 14 Smart Self Powered Siren with Digital ComLink 0 sn 15 Unbreachable Digital ComLink a n 15 Smarischarging so 4 ck s on euim d eR ais Od E SE eee det nde Dd 15 Personalized Siren Sounds 6 o 15 Long term chirp silencing ata s 15 Remote controlled chirp muting 22s 15 QuietChirps muffled chirp sound leve sss 15 Automatic low battery warning n 15 Noise abatement circuitry oaaae 15 User selectable features 22 ha hos 16 Step by step programming instructions 6 2222s 16 Adding new remote controls 2 22s 18 How fo erase the codes of lost or stolen remote controls i 18 Table of user selectable features 2222s 19 20 Standard Features of the Concept 50x Lifetime Warranty For as long as you own the vehicle Clifford will repair or replace the control unit and remote controls free of charge see
17. ew times Once you ve changed a few settings you ll find that programming Concept 50x is so easy that you can even do it while driving The system comes with all of its features pre programmed as noted by the bold type in the Table of user selectable features on pages 19 20 To change any of the settings use the steps noted below To restore the feature to its factory setting just repeat the procedure How to change a user selectable feature Briefly here s how it will work e Pick a feature from the Table on pages 19 20 noting its column and row numbers First you ll need to get into program mode by entering your secret valet mode code see page 10 After you have entered your code press and hold the momentary side of the PlainView switch until you hear a chirp You re now in the Feature Select position e Next you ll press the latched side of the switch a number of times identical to the column number Lastly you will press the momentary side of the switch a number of times corresponding to the row number That s all there is to it After you enter the feature s column and row numbers you ll hear either one chirp to indicate that the feature has been turned off or two chirps if turned on It s easy once you ve done it Try the examples on page 19 Step by step programming instructions 1 Refer to the Table of user selectable features and make note of the column across number and the row down number of the feature s you wi
18. he Concept 50x cont W Remote Window Sunroof Closure Capability On certain vehicles including several models of Mercedes Benz Jaguar Volkswagen and BMW the system s integrated timer and an optional relay can be used to automatically close the power windows and sunroof every time you remotely arm your system W QuietChirp Whenever you desire you may choose to lower the decibel volume of the arm and disarm chirps to a level that is clearly audible but less obtrusive than the full volume chirps All it takes is a few flicks of a switch W User Selectable AutoArming Automatically arms itself passively if you forget and has all these additional features m AutoArming Enable Disable You may disable or re enable the AutoArming feature with just a few flicks of a switch m AutoArm amp Lock You may set the system to automatically lock the doors every time the system AutoArms m Visual Indication Two parking lights flashes signal that the 30 second countdown to AutoArming has started m Instant AutoArm Bypass Just a quick turn of the ignition switch will bypass AutoArming for one cycle perfect when fueling the vehicle AutoArming is automatically restored the next time you park W Patented Smart Prior Intrusion Attempt Alert When you return to your vehicle and remotely disarm your Concept 50x a special chirp and indicator light flash sequence will audibly and visually alert you from a distance if an i
19. ic means since whenever you wish the system will visually identify the activated triggers and sensors in reverse chronological order W Patented Remote Control Code Learning with MultiRemote Recognition Just a few flicks of a switch lets you match to the system up to 4 different 12 channel Clifford ACG remote controls Just as easily a lost or stolen remote control can be deleted W Multiple Car Control You may use the same remote to control Concept 50x systems on up to six of your other vehicles W High Luminescence LED Status Indicator Adds visual deterrence and identifies system status W Patented SmartPowerUp II When power to the system is disconnected the system s non volatile memory always remembers the security system s last state armed or disarmed and returns to that state when power is restored So if a thief disconnects the power and then restores it in an attempt to start the car the system will instantly re arm Your 4 button 12 channel remote controls The 4 button 12 channel remote controls are ultra sophisticated miniature radio transmitters powered by a tiny 12 volt battery Range is up to 30 meters A weak remote control battery will reduce range Electrical interference and even sunspots can interrupt the signal from your remote control to the system If this happens repeatedly press the remote control button this works better than holding the button down The 4 button 12 channel remote control is
20. indow 7 If you are not satisfied with the detection level and wish to increase sensitivity press button 2 on your remote control To decrease it press button 4 Each time you increase sensitivity the siren will sound higher and higher pitched chirps Conversely sensitivity decreases are confirmed with lower and lower toned chirp Three chirps indicate minimum and maximum settings There are 32 sensitivity levels for the Proximity Sensor s interior zone 16 for the less critical warning zone 8 Repeat steps 6 and 7 until you are satisfied with the sensitivity then press button 1 to record the new sensitivity setting and exit the sensor test adjust mode you ll hear three chirps to confirm exit You may now either repeat steps 1 4 for the other sensor zone or press button 1 again to arm the system Und Remote controlled override of one or both sensor zones Transmitting channel 10 within 10 seconds of arming the system will override the exterior warning zone of the Proximity Sensor you ll see 4 parking light flashes to confirm the zone override This is useful when parking in an area with heavy pedestrian traffic Transmitting channel 10 again within the 10 second period will override both zones of the sensor for those times when you must leave a passenger or pet in the vehicle The sensor zones are automatically restored the next time you arm the system 12 Built In Two Point Autolmmobilizer Thirty seconds after you turn off th
21. is setting see User selectable features on pages 16 20 E nstant AutoArming bypass Prevents AutoArming when fueling the vehicle and other times when you wish to temporarily bypass AutoArming To activate Instant AutoArming Bypass rapidly turn the ignition switch to ON then OFF You will hear a single siren chirp to confirm that the system will not AutoArm The system reverts to its normal operating mode when you next start the engine 9 UltraSecure Coded Valet Mode In seconds thieves can disable all other alarm brands by hotwiring the ignition and flicking an easy to find hidden valet switch Your system has safeguards that absolutely ensure a thief cannot enable the valet mode as a way of turning off your system How To enable valet mode the driver must first enter a secret valet code on the PlainView switch Your code will be a 1 to 3 digit number of your choosing Each digit can be any number from to 9 i e the code can be any number between 1 and 999 except those that contain a zero Whenever the system is in valet mode it overrides the AutoArming feature see page 9 and all the security features are turned off At various times you will need to switch the system off For instance when having your car serviced washed or parked by a valet Your factory set valet code is the single digit 2 NOTE If you temporarily lose the use of your remote controls you can disarm The system by enabling valet mode
22. it program mode 16 l EXAMPLE 1 Turn on AutoArm amp Lock When the system AutoArms see page 9 it does not normally lock the doors to ensure that you cannot accidentally lock the keys inside the vehicle To enable this feature you ll note that AutoArm amp Lock is in column 3 row 2 of the table on pages 19 20 The off in bold type indicates the factory setting The following example will turn on AutoArm amp Lock 1 To enter program mode turn on the ignition enter your valet code as noted on page 10 then hold the switch in its momentary position until you hear a chirp 2 Select column 3 by pressing the latched side and then returning the switch to its center position three times then wait for the three chirps to confirm column 3 To select row 2 press momentary two times you ll hear a chirp each time you press the momentary side 3 After a brief pause you ll hear two chirps to confirm that AutoArm amp Lock is now on 4 Turn the ignition off You ll hear 3 chirps confirming automatic exit from the program mode and you re done If you make an error just turn off the ignition and start again To turn AutoArm amp Lock back off just repeat steps 1 4 In step 3 you ll hear one chirps to confirm that the feature has been turned back off Remember one chirp off two chirps on NOTE You have 10 seconds to enter the row number after selecting the column If you wait too long the system jumps back to the Fe
23. just entered do not match The system will hear two chirps to confirm the new accessory timer duration has reverted to the previous code 20 Copyright Clifford Electronics Inc 1996 31 106A C5xHOLOM 896
24. ly for on going visual confirmation of valet mode 10 To exit valet mode 1 Turn the ignition switch to its ON position or start the engine 2 Flick the switch back to its center position The LED will turn off to confirm that the system is now in its normal operating mode Setting your own secret valet code Since all Concept Series systems have the same factory set code it is highly advisable that you set your own valet code You may choose any 1 2 or 3 digit code that does not have any zeros You can also change your valet code whenever you want Simply write down the 1 to 3 digit code you wish to use remember no zeros in the code then refer to the User selectable features section on pages 16 20 Example Let s say you want to set your valet code to 31 To do so you would do the following 1 From the Table of user selectable features on pages 19 and 20 you would note that the set a new secret valet code feature is in column 3 row 6 2 Enter program mode by turning on the ignition entering your current valet code then pressing the PlainView switch to its momentary side for 3 seconds until you hear a chirp 3 Select column 3 by moving the switch between latched and center 3 times i e latched center latched center latched center After a brief pause you will hear 3 chirps to confirm that you have selected feature column 3 4 Select row 6 by pressing and releasing the momentary side of the switch 6 times
25. m is disarmed 3 silently arm or disarm no 3 4 activate an optional accessory no 4 5 arm or disarm a Concept 50x on your second vehicle yes once 1 Command a Concept 50x on your second vehicle to 6 optionally turn on a timed pus if the system is armed yes gigs 2 optionally pop the trunk if the system is disarmed activate an optional accessory f controlled by a Concept 50x on your second vehicle yes once 3 activate another optional accessory 8 controlled by a Concept50x on your second vehicle yes once 4 9 enter exit valet mode yes twice 1 10 remotely tum off one or both sensor zones yes twice 2 activate an optional accessory controlled by a Concept 50x on your third vehicle yes wiee 12 activate another optional accessory yes twice 4 controlled by a Concept 50x on your third vehicle TO ARM Press button 1 channel 1 once You will hear two chirps and the THE SYSTEM indicator lights will flash twice The dashboard LED will flash repeatedly and the car doors will automatically lock TO DISARM Press button 1 channel 1 again One chirp and one indicator THE SYSTEM light flash confirms disarming In addition the doors will auto matically unlock and the interior lights will turn on and stay on for 30 seconds or until you start the engine whichever occurs first TO SILENTLY Press button 3 channel 3 Your Concept 50x system will arm or ARM OR DISARM
26. n go right away to the row selection momentary side of the switch Now within 10 seconds press the momentary side two times to jump to row 2 After a brief pause you ll hear 1 chirp to confirm that AutoUnLock is now off 17 4 Note that the QuietChirps feature is in the same column 2 row 5 Simply press the momentary side 5 times After a brief pause you ll hear two chirps to confirm that the QuietChirps feature is now on 5 To exit the program mode turn the ignition off You ll hear 3 chirps to confirm program mode exit You just made three programming changes in only five steps Easy isn t it Notice again that in this instance you did not have to re select column 2 If you don t touch the switch the system stays in the column for 10 seconds to allow you to select any other feature s in the same column without having to re enter the column number Of course you can also toggle the latched side to select a new column If you wait more than 10 seconds the system automatically jumps back to the Feature Select position This is the stand by position ready for entry of a new programming selection If no action is taken for the next 60 seconds the system automatically exits program mode perfect if you program while driving or if you forget to turn off the ignition Adding new remote controls For other drivers in your family or if you wish to control Concept 50x systems on your other cars with the same remote contr
27. n vehicles with factory delayed or dimming courtesy lights If a sensor is malfunctioning you will receive the usual 2 chirps and 2 flashes then 10 seconds later there will be 4 chirps and 4 flashes W Specific malfunction identification If you get the 4 chirp 4 flash signal upon arming perform the following to identify the malfunctioning trigger or sensor 1 Remotely disarm then turn on the ignition The LED status indicator inside your vehicle will be flashing pause then repeat 2 Count the number of blinks in one cycle between pauses for your convenience the blink cycle repeats a total of 5 times and refer to the chart below 1 blink Proximity Sensor 3 blinks Optional sensor 4 blinks Door trigger 5 blinks Trunk trigger 6 blinks Hood trigger If your vehicle has a factory installed feature that turns off or dims the interior courtesy lights five seconds or more after you exit the vehicle the system cannot provide this indication 13 Automatic malfunction bypass In the event of a component malfunction the system will automatically bypass any faulty point and arm all other triggers and sensors to provide the utmost possible protection until you can have the system serviced by your local Authorized Clifford Dealer If you accidentally armed with the hood trunk or a door open just close the open point and the system will again monitor that point Multiple event TotalRecall The syst
28. ntrusion attempt was foiled while you were away Your Concept 50x will even identify the specific trigger or sensor that detected the intrusion attempt W Remote Controlled Courtesy Lighting For your personal safety and convenience when you remotely disarm your Concept 50x the interior lights turn on and stay on until you start the engine or 30 seconds whichever occurs first Built In Indicator Light Flasher On board relay and circuitry will visually confirm door lock and system status 4 Standard Features of the Concept 50x cont W Patented Smart AutoTesting Automatically tests all system triggers and sensors every time you remotely arm and warns you if you accidentally arm your Concept 50x system with the hood or trunk open If there is a genuine trigger or sensor malfunction the system will specifically identify the problem thereby eliminating time consuming and costly trouble shooting W Patented Malfunction AutoBypass with Automatic Monitoring In the unlikely event of a trigger or sensor malfunction Concept 50x automatically bypasses the malfunction and arms all other points to continue relentless protection of your vehicle If you simply left the hood trunk or a door open when you armed just close it and the system will again monitor that trigger point W Multiple Event TotalRecall Concept 50x s memory stores the identity of the last eight trigger and sensor activations This provides an invaluable diagnost
29. ol you can buy additional remote controls from any Clifford Dealer and program them into the system yourself Each Concept 50x will respond to as many as four 12 channel ACG remote controls To add a new remote control to the system use the procedures noted in the User selectable features section on pages 16 20 How to erase the codes of lost or stolen remote controls If one of your remote controls is ever lost or stolen you can erase its digital codes from the system memory to make sure that the missing remote control can never be used to disarm your system To do so use the Erase all channels feature feature column 1 row 5 on the Table of user selectable features on pages 19 20 This will clear all remote control codes from the system memory Then simply program each remaining and or replacement remote control as noted in the Adding new remote controls section above 18 Table of user selectable features 1 chirp OFF two chirps ON Feature Select Row 1 Ist momentary Row 2 2nd momentary Row 3 3rd momentary Row 4 4th momentary Row 5 5th momentary Row th momentary Column 1 Column 2 Column 3 Column 4 Ist latched 2nd latched 3rd latched 4th latched Add new remote to channel 1 AutoLock on off AutoArming on off Sound 1 on off info on page 9 NOTE 1 info on page 12 info on page 11 info on page 16 Add new remote to channel 2 AutoUnLock
30. ou can enter or exit valet mode Indicator light flashes visually confirm valet mode entry and exit Built In Two Point Autolmmobilizer For the utmost in theft prevention two AutoImmobilization circuits interrupt both the starter and electronic fuel pump while the system is armed Even if a thief were to pull the fuses or cut all the wires the starter and fuel pump remain immobilized m Failure Proof Driving Safety Even in the unlikely event of a system malfunction the AutoImmobilizer will not stop the engine while the vehicle is being driven Standard Features of the Concept 50x cont W Remotely Adjustable Dual Zone Proximity Sensor Two sensor zones provide full protection If someone is lurking near your car the system will sound a warning tone But if a thief actually leans into the passenger compartment the system will instantly blast the siren It is impervious to wind and temperature variations that cause ultrasonic sensors to false alarm and you can even adjust sensitivity of each zone via the remote control W Dual Mode Chirp Silencing W henever you wish just a press on the remote control will arm and disarm the system silently It s perfect when parking at night in a quiet residential area Or if you prefer you can turn off the chirps on a long term basis until you wish to turn them back on W Remote Door Locking Unlocking with Built in Relays No more fumbling with keys in the dark or bad weather A pr
31. r instance to transmit channel 5 press the LevelShift button once then press button 1 While you transmit you ll notice that the LED indicator blinks twice pauses blinks twice etc this indicates level 2 W Jo transmit channel 9 10 11 or 12 Press the LevelShift button twice This shifts buttons 1 4 to level 3 channels 9 12 Then press the corresponding button within the next 7 seconds For instance to transmit channel 10 press the LevelShift button twice then press button 2 While you transmit you ll notice that the LED blinks three times pauses blinks three times etc this indicates level 3 NOTE One second after you stop transmitting level 2 or level 3 channels 5 12 the remote control automatically returns to level 1 channels 1 4 6 What each button channel does Your Concept 50x remote controls come pre programmed so that certain channels command certain functions If you wish you can actually assign any channel to any function see pages 16 20 The following chart indicates what each remote control channel number does and how to transmit each channel number Factory settings of the 12 remote control channels Transmitting Press the How Press channel Causes the system to LevelShift many button number button times number 1 am or disarm and lock or unlock the doors no 1 optionally turn on a timed device if the system is armed 2 AND no 2 optionally pop the trunk if the syste
32. sh to program 2 Turn on the ignition or start the engine skip this step if the engine is running 3 Enter your valet mode code see page 10 then press the Plain View switch to its momentary side for 3 seconds until you hear a siren chirp the system LED will also turn on to indicate program mode You are now in the Feature Select position 4 Select the feature column Toggle the switch in and out of the latched position the same number of times as the column number of the selected feature NOTE each latched to center motion is counted as one Pause You will hear the same number of chirps as the column number you have selected audibly confirming your selection 5 Select the feature row Press and release the momentary side the same number of times as the feature s row number You ll will hear a chirp each time you press 6 If there is a NOTE for the selected feature perform the actions noted Pause You will hear either one or two chirps Two chirps ON one chirp OFF 8 You may select another feature or you may exit program mode a To select another feature in that column repeat step 5 within the next 10 seconds after 10 seconds 3 chirps mean you are now back in the Feature Select position b To select a different feature column go to step 4 c To exit program mode turn the ignition off you ll hear 3 chirps and the LED will turn off If driving just wait 60 seconds for the system to automatically ex
33. stantly disarming the alarm and unlocking the doors It s like giving the thief your car keys But not if you have the Concept 50x since it utilizes complex digital signal processing and unbreachable encryption to randomly change the digital code every time you use the remote control Your remote control will never transmit the same code twice and the control unit will never accept the same code twice Thus the code recorded and played back by the thief s code grabber will never be accepted by your Concept 50x Smart prior intrusion attempt alert If you hear three chirps when you remotely disarm instead of the usual one chirp it means that a trigger or sensor was activated in your absence When you enter the vehicle and turn on the ignition or start the engine the LED will blink 1 6 times pause then repeat the blink cycle 4 more times Count the number of blinks in one cycle and refer to the chart on page 13 to identify the trigger or sensor that was activated while you were away How to interpret the chirps and indicator light flashes When you use the remote the system responds with chirps and indicator light flashes Chirps and flashes Meaning 1 Your system is disarmed 2 Your system is armed 2 and then 4 Armed butthere is a door open or the sensor is malfunctioning see Smart AutoTesting on page 13 3 Disarmed butthere was an intrusion attempt while you were away see Smart prior intrusion attempt on page 8 4
34. th your remote control simply by transmitting channel 9 LevelShift twice then button 1 In addition to the above indications two parking light flashes will confirm that you have remotely enabled valet mode while a single flash confirms exiting of valet mode Remote controlled sensor adjustment You may individually test and adjust the settings of each sensor zone 1 Disarm the system with the remote control open the driver s window 2 Turn the ignition to the ON position enter your valet code then press and hold the momentary side of the switch until you hear a siren chirp 3 Flick the switch to the latched position and back to center five times Pause You will hear 5 chirps Tap the momentary side of the switch 5 times you will hear a chirp each time Turn the ignition switch off exit the vehicle close the door then select the zone you wish to adjust a Interior zone Transmit channel 11 LevelShift twice then button 3 b Exterior zone Transmit channel 12 LevelShift twice then button 4 6 To test the current sensitivity setting a Interior zone Lean into the passenger compartment You will hear a chirp when the zone detects your presence Ideally it should chirp when you lean over the driver s seat but remain silent when you lean toward the window b Exterior zone Lean toward the window You ll hear a chirp when the zone detects you Ideally it should only chirp when you are within one foot of the w
35. the new number of chirps as the digit you choose when you move the switch to the remote control You will hear two chirps to confirm programming of channel 2 latched side e g if the first digit is 4 you ll hear four chirps when you NOTE 3 Transmit channel 3 or other channel of your choosing of the new press the latched side remote control You will hear three chirps to confirm programming of channel 3 b Make sure to return the switch to its center position when complete NOTE 4 Transmit channel 4 or other channel of your choosing of the new c Wait 3 seconds until you hear 2 chirps indicating the new code has been remote control You will hear four chirps to confirm programming of channel 4 accepted NOTE 5 When you hear one chirp all remotes will have been erased from the d Turn the ignition off You ll hear 3 chirps to confirm program mode exit system memory You must now add the new and or existing remote controls to and the LED will turn off the system i e program channels 1 4 of each remote that will be used with e VERY IMPORTANT You must immediately test your new secret your Concept 50x valet code Turn the ignition on enter your new code then flip the switch NOTE 6 The accessory timer starts as soon as you select this feature When the to its latched position The LED will illuminate If it does not the new code duration you wish has been reached press button 1 on the remote control You you programmed and the one you
Download Pdf Manuals
Related Search